C型胶管(一端带直角弯头)Rubber pipe assembly, C-type(with an elbow, 90°)
上部内防喷器接头(远控) Upper IBOP (remote)
主机防风棚可燃气体探测仪Inflammable gas detector in main equipment shed
YM-16-Ⅱ型液压猫头YM-16-Ⅱ Hydraulic Cathead
主发电机组额定功率×台数Rated power X quantity, main generator set
将所有DAQ数据存于硬盘Store all DAQ data on hard disk.
由任式金属硬密封泥浆阀门Mud valve , union type, metal to metal seal
焊拉式金属硬密封泥浆阀门Welding metal seal mud valve
焊接式金属硬密封泥浆闸门Welding metal rigid mud-sealing gate
焊接式金属硬密封泥浆阀门Welded metal hard sealing mud valve
底部压井管线包括四个阀门Kill line(including 4 valves)
API阀门DN50组数量API gate valve DN50 union
刹车液压操作系统额定压力Rated hydraulic operation system pressure of brake
金属硬密封泥浆阀门密封件Metal hard seal mud valve sealings
设计符合API4F规范The mast conforms to API 4F
设计符合API9B规范Conforms to API 9B
设计符合API8A规范Conforms to API 8A specification
设计符合API7K规范Conforms to API 7K specifications
柴油发电机组保养配件清单Maintenance parts list of diesel generator set house
司钻控制室及钻井参数仪表Driller's control cabin and drilling parameter instrument
焊接式金属硬密封泥浆阀板Welding metal seal mud valve plate
每个泵上的三个缸可以互换The 3 hydraulic cylinders of every pump can be interchanged.
操作台升降行调节范围6m Console rising and lowering distance is 6m
带传动,以简化减速机构. Belt transmission is adopted, which simplifies the speed-reducing mechanism.
主滚筒尺寸(直径×长度)Main drum size(Dia.×Length)
压力差开关(油气分离器)Pressure difference switch (oil-gas separator)
旋转方向(面向飞轮端视)Rotation direction(facing to flywheel)
橡胶管线1""(约30米)Rubber pipe line1""(About 30 m)
推拉式塑钢窗(钢化玻璃) Slide plastic-steel window (tempered glass)
刹车鼓尺寸(直径×长度)Brake rim size(Dia.×Length)
排出滤网及辅助管路(二)Discharge Filter Screen and Assistant Pipe(2)
空气过滤器滤芯(重负荷)Air filter element(heavy duty)
胶管总成(长度仅供参考)Rubber hose assembly(Length for reference)
电传系统部分(发电机柜)Electric drive system(generator cabinet)
电传系统部分(开关柜)Electric Drive System(Cubicle Switchboard)
打捞震击器(液压上击器)Fishing jar
不锈钢丝护套胶管(横向) Stainless wire jacketed hose(horizontal)
不锈钢丝护套胶管(横向)Stainless wire jacketed hose(cross)
(5″钻杆28米立根)(5"drill pipe 28m stand)
四川宏华石油设备有限公司Sichuan Honghua Petroleum Equipment Co., Ltd.
发电、气源房布置各部件图Parts drawing for Generator/air source house
钻井液管汇通径/额定压力Drilling fluid manifold bore size / rated pressrue
扣压式软管接头Press type softpipe fitting
金属硬密封泥浆阀门阀座Metal hard seal mud valve seat
CAT3406柴油机组CAT3406 Diesel engine generator set
起升大绳死绳端固定装置Fixation device of hoisting wireline deadline end
主机防风棚排风系统控制Control of the ventilation system in main equipment shed 泥浆泵H2S气体探测仪Mud pump H2S gas monitor
固控区H2S气体探测仪H2S gas detection instrument in Solid control area
外螺纹/外螺纹穿板接头Out thread/external thread bulkhead joint
井场交流区域配供电系统Well site AC distribution system
绞车辅助驱动电机/台数Drawworks auxiliary driving motor / quantity
辅助发电机组功率×台数Auxiliary generator set power X quantity
鹅颈管与水龙带联接方式Goose neck pipe and rotary hose connection type
电动倒绳机及钻井钢丝绳Electrical spooler and drill line
司钻偏房安装在支撑架上The doghouse installed on supporting frame
通风式气胎离合器摩擦片Ventilated type air tube clutch friction plate
小气室普通气胎离合器囊Clutch Ballonet
装在底座上司钻位置对面Installed on the substructure facing driller side
压力传感器配2m长电缆Pressure transducer, with 2m long cable
突面板式平焊钢制管法兰Crowning plate type flush welding steel tube flange
凸面板式平焊钢制管发兰Convex type plain welding flange
移送气缸支撑架装置部件SUPPORT, MOVING CYLINDER
无火花型三相四极插件Non-spark three-phase four-pole plug-in
自动电压调节器反应时间Response time, auto voltage regulator
二层台及挡风墙、飞机架Racking board and bayshon, cantilever
KXT型可曲挠橡胶接管KXT type flexible rubber connecting pipe
井架左右四段及左右五段Left and right section IV & V of mast
由壬式双刻度抗震压力表EP dual-scale pressure gauge, union type
动力及电传动系统区设备Power and electric driving system equipment
金属硬密封泥浆阀门阀板Metal hard seal mud valve plate
振动罐-吸收罐(录井)Shaker tank-suction tank( well logging)
油气分离器滤芯(次级)Oil-gas separator filter element(secondary)
油气分离器滤芯(初级)Oil-gas separator filter element(primary)
印制电路板(发电柜)Printed circuit board( generator cabinet)
外形尺寸(长×宽×高)Overall measurement (L x W x H)
干粉灭火器(带安装架) Dry powder fire extinguisher (w/installation frame)
电传系统部分(同期柜)Electric drive system(synchronizing cabinet)
电传系统部分(变频柜)Electric drive system(converter cabinet)
低压泥浆系统(固控室)Low pressure mud system(solid control room)
(含由壬fig100)(includes Union fig100)
发电、气源房布置图总图Layout of Generator/Air Source House
注可按用户要求颜色配Note: the colour is based on client requirement.
铺板(六)与左右上座Paving plate(6) and left&right upper seat
立根盒前梁与左右上座Front beam of setback and left&right upper seat
机架与绞车护罩及底座Main frame and drawworks guard and skid
卡特辅助柴油发电机组CAT aux. diesel generator set
防爆应急荧光灯电池组Battery set of Explosion proof emergency fluorescent lamp 人字调节支撑架含销轴A-frame adjustable support (including pins)
泥浆泵可燃气体探测仪Mud pump gas monitor
固控区可燃气体探测仪Flammable gas detection instrument in Solid control area
双液动节流管汇控制箱Double hydraulic choke manifold control box
动力钳及套管钳备件箱Power tong and casing tong spare parts box
泵及螺杆压缩机备件箱Spare parts box of pump and screw compressor
BOP控制装置集装箱BOP control unit container
高压及内防喷高压管线High pressure pipe line and inner blowout preventing pipe line 左下段及人字架左支腿Left lower section and A frame left legs
右下段及人字架右支腿Lower section and A-frame right leg
钻杆台绞车气路安装图Air piping diagram for drill pipe board winch
左路工作钳总进油接头Oil inlet joint, left service caliper
右路工作钳总进油接头Oil port joint, right service caliper
无螺纹焊接式管接头Unthreaded Welded Pipe Connector
扩口式组合三通管接头Combined T joint, flare type
可曲挠性合成橡胶接头Flexible rubber joint
焊接式头端直通管接头Through Welded Pipe Connector
叉形状预绝缘管状端头Lug(fork-shaped, tubular end)
发电机控制及并车系统Generator control and paralleling system
液压动力钳滑轮2套2sets of hydraulic power tong pulley
手动大钳平衡重2套2sets Sheave of manual tong
常开式制动钳密封一套Normally open brake tong seals
常闭式制动钳密封一套 A set of normal closed brake tong sealings
钻台上一个远程控制台Remote console on drill floor
循环泵电机功率/转速Circulating pump motor power/rotation speed
刹车泵电机功率/转速Brake pump motor power/rotary speed
机具泵电机功率/转速Tools pump motor power/rotary speed
电压、频率、功率因素Voltage, frequency, and power factor of generator set
钻井泵额定功率/台数Drilling pump rated power/ quantity
泥浆泵额定功率×台数Mud pump rated power×quantity
泥浆泵电机功率/台数Mud pump motor power / quantity
液压大钳配件套管扳手Casing spanner for hydraulic power tong
旋钮带锁定,圈数指示Knob has a lock and circle number indicator
游吊系统倒绳用钢丝绳Traveling system spooling steel line
用于穿绳、取绳、存绳Used for reeving, spooling and storing drill lline
正压式压缩空气呼吸器Compressed air respirator
载荷限制器手柄制动器Handle brake of load limiter
室内吸顶式烟雾报警器Roof smoke detector
除砂除泥一体化清洁器Desander& desilter combined mud cleaner
通风式气胎离合器气囊Ventilated type air tube clutch air bag
通风式膜式离合器气囊Clutch Ballonet
刹车泵额定压力/排量Brake pump rating pressure/displacement
机具泵额定压力/排量Tools pump rated pressure/displacement
绞车轴编码器带有电缆Drawworks shaft coder with cable
MCC房VFD房线缆MCC house VFD house cable
双三通阀带溢流阀阀块Dual 3-way valve with relief valve block
美制螺纹锥面扩口接口American system screw thread taper expanded interface
转盘驱动交流变频电机AC VF motor of RT drive device
绞车驱动交流变频电机Drawworks AC VF motor
固定式螺杆空气压缩机Fixed screw air compressor
隔爆型三相异步电动机Ex-proof three phase asynchronous motor
铺板(十二)与立根盒Paving plate(12)and setback
输送装置止推轴承密封Stop bearing seal of transportation device
发电-气源-MCC房Generating-air source-MCC house
井架左右中下段及上段Mast L&R, middle lower section and upper section
微型高压软管接头总成Micro HP hose connector assembly
三通型鹅颈管组件总成T goose neck assembly
高压耐火隔热软管总成High Pressure Fireproof Hose&heat insulating hose assembly 双轮闭口锁环起重滑车Lifting yoke
VFD到泥浆泵电缆槽Cable trough from VFD to mud pump house
VFD到钻台面电缆槽Cable trough from VFD to drill floor
MCC到泥浆罐电缆槽Cable trough, MCC to mud tank
控制管路过滤器维修包Maintenance kit control pipeline filter
套管卡瓦钻铤吊卡CD Casing slip DC elevator CD
C型胶管/单弯90°Rubber pipe assembly, C-type/single elbow, 90°
C型胶管/双弯90°Rubber pipe assembly, C-type/ dual elbow, 90°
所有接头都为震击由壬All connections are hammer unions.
密封胶芯使用寿命长. Packing unit has enough rubber volume and long service life
采用可靠的复合密封. Reliable compound seal is adopted to ensure no leakage.
滚子补芯,四销驱动, Roller bushing,squre driving,
印制电路板(同期柜)Printed circuit board(synchronous cabinet)
液压系统(两个液缸) Hydraulic system(two cylinders )
液压大钳(一年备件)Hydraulic power tong(one year spare parts)
液控换向阀(力士乐)Hydraulic control reversal valve (Roxreth)
压力差开关(过滤器)Pressure difference switch(filter)
联轴节链轮(变速箱)Shaft-connecting sprocket (gearbox)
接插件(插头/插座)Connector(plug/socket)
防爆护罩(含摄像机)Explosion proof guard ( including camera)
防爆控制按钮(带灯) EX Control button(with lamp)
电传系统部分(其它)Electric drive system(others)
柴油机底座(加宽台) Substructure of Diesel Engine
(含螺杆压缩机1台)(including one screw compressor)
(KB-75空气包)( KB-76 air discharging bag)
转盘电机风机引风装置Air-guide device of RT motor blower
循环泵额定压力/排量Rating pressure/displacement of circuling pump
底漆低表面处理环氧漆PrimerLow surface treat epoxy painting
悬臂吊含电机,基座Cantilever crane includes motor and fundation support
三相A移动插头插座Inserts
绞车前梁与左右上座Drawworks front beam and left&right upper seat
地面高压管汇固定座HP manifold Fixed Seats
钻台高压管汇闸阀组Gate valve assembly for drilling floor highpressure manifold 地面高压管汇闸阀组Ground highpressure manifold gate valve assembly
配气动过卷防碰装置Pneumatic over roll anti-crush device
泥浆液面报警器装置Mud Lever Alam Devices
防喷器液压控制装置BOP hydraulic control device
地面防喷器控制装置Ground BOP control device
登梯防坠落保护装置Climbing anti-falling device
固控区排风系统电源Power supply for ventilating system of solid control area
空气滤清器次级滤芯Air filter secondary filter element
空气滤清器初级滤芯Air filter primary filter element
初级油气分离器滤芯Kit. Seperator
液动节流管汇控制箱Hydraulic choke manifold control box
进口固控系统备件箱Solid control system spare parts box
管汇及固控等备件箱Spare parts box of manifold and solid control
泵及防喷器等备件箱Spare parts box of pump and BOP
左起升人字架前支腿Left front leg of lifting frame
左起升人字架后支腿Left back leg of lifting frame
右起升人支架前支腿Front leg of right lifting frame
右起升人支架后支腿Back leg of right lifting frame
司钻室气控箱安装图Pneumatic Control Box in Driller's Cabin installation drawing 两用水龙头各部件图Dual purpose swivel parts drawing
美制外螺纹穿板接头British measurement external thread bulkhead joint
快插式螺纹穿板接头Quick threaded bulkhead connector
可曲挠合成橡胶接头Flexible rubber joint
焊接式母由壬死堵头Weld Box Union Plug
焊接式公由壬死堵头Welded male union plug
齿轮泵出油三通接头T-joint of oil gear pump output
插入式螺纹穿板接头Plug-in type threaded piercing connector
Y形插入式螺纹接头Y-shaped plug-in type threaded connector
Y形快插式螺纹接头Quick push-in fitting of Y-shape
L形快插式螺纹接头Quick push-in fitting, L-shape
L形插入式螺纹接头Quick push-in fitting of L-shape
绞车油、气、水系统Oil, air and water System of DW
风动马达及传动系统Pneumatic motor and drive system
VFD房及控制系统VFD house and control system
MCC房及控制系统MCC house and control system
DC用玻璃管保险丝Glass tube fuse for DC
AC用玻璃管保险丝Glass tube fuse for AC
转盘电机功率/台数Rotary table motor power / quantity
绞车电机功率/台数Drawworks motor power / quantity
触摸屏上显示的参数Parameters displayed on touch screen
控制电缆及辅助设施Control cable and auxiliary equipments
笔,圆珠总成,蓝色Pen, Ball Point Assy, Blue
直角接头,带O型圈Right-angle elbow, with O-ring
液压大钳配件密封圈Seal ring for hydraulic power tong
搅拌机减速箱密封圈Agitator reducer sealing ring
焊接式由壬密封垫圈Welded union seal washer
断路器合闸压线圈Chopper switch on winding,
液压大钳配件黄油枪Grease gun for hydraulic power tong
泥浆回流流量传感器Mud Return line sensor assembly
各种气体检测报警器Gas detects and alarms
个人随身气体报警器Personal gas warner
钢丝绳及液压卷绳器Wire line and hydraulic spooler
返流泥浆流量传感器Return mud flow sensor assembly
常开型电磁阀岛阀片Noramlly open Solenoid valve terminal valve plate 常闭型电磁阀岛阀片Noramlly closed Solenoid valve terminal valve plate 普通气胎离合器气囊Clutch Ballonet
出磁性过滤器30目Magnetic filter, 30 mesh
美制扩口管接头螺母British measurement flared joint nut
金属硬密封泥浆阀门Metallic hard sealing mud valve
排出滤网及辅助管路Discharge Filter Screen and Assistant Pipe(1)
防爆钢丝绳电动葫芦Wire line electric hoist, EX-PRF
冷启动装置额定排量Cold start device rated displacement
机具吸油过滤器法兰Flange of suction filter
机具回油过滤器法兰Flange of oil return filter
晶闸管/二级管模块Transister/diode module
VIP数据录井模块VIP data logging module
耐油胶管NPT丝扣Oil proof rubber hose NPT thread connection
阀杆导向器装卸工具Handling equipment of valve lever guide device
测斜绞车配件及工具Accessaries and tools of deviation winch
平移液缸缸径/杆径Slipping cylinder diameter/pole diameter
顶升液缸缸径/杆径Lifting cylinder diameter/pole diameter
一年备件除气器配件List of one year spare parts for degaser
液压站电气系统部件Parts for electric system of HPU
压力表高压油管部件Parts for High-pressure oil line of pressure gauge 气源系统其他附属件Accessories of air source system
起升人字架撑杆组件 A frame components for rig-up
泥浆泵安装必须配件Necessary accessories of mud pump installation
供给喷嘴钨制嵌入件Supply nipple parts
发电机控制系统部件Parts of Generator Control System
BOP防喷器连接件BOP connecting parts
防爆区域内防爆等级Explosion proof of explosion proofing area
高压呼吸空气压缩机High pressure breathing air compressor
吸入罐高压剪切管汇Shear manifold, suction tank
混浆罐高压剪切管汇HP shear manifold of mixing tank
安全阀及灌注泵管汇Safety valve and charge pump manifold
队长室和办公室电话Telephones in tool pusher's office and other offices
发电机控制及同期柜Generator control and synchronizing cabinet
方钻杆及大小鼠洞管Kelly & Mouse Holes
泵房保温棚底座方管Square pipe of insulated booth basement of pump house 远/近控制转换开关Remote/local shiftswitch
液压钻杆钳尾桩1个One snub line stake of hydraulic drill pipe power tong
手动大钳尾绳桩2个 2 pcs Tail rope pole of manual tong
电缆专用SLS型钢Special steel for cable, SLS type
锤击式钢制由壬密封Impact steel unoin seal
防爆比例先导溢流阀Pilot operated proportional relief valve, explosion-proof
二位三通常闭按钮阀Two-position three-way normally closed valve
二位三通常闭气控阀Two-position three-way normally open pneumatic valve
二位三通常开气控阀Two-position three -way normally open air control valve
叠加式双单向节流阀Double-single chock valve
电瓶输出负极连接端Cathode connection end of battery
电瓶输出正极连接端Anode connection end of battery
冷暖分体式防爆空调Warmer/cooler air conditioner, explosion proof
液压系统及液压站等Hydraulic system and HPU
泥浆泵随机工具清单Special Tools List For Mud Pump
左钻台偏房外形尺寸Overall dimension of the left rig floor dog house
右钻台偏房外形尺寸Overall dimension of dog house on the right side of rig floor 最大缸套直径×冲程Max. liner dia. x stroke
方形带座外球面轴承Square type sphere bearing
支架全部由槽钢制成The whole bracket is made of channel steel
移送气缸支撑架总成Support assembly, moving cylinder
压风机进排气阀总成Compressor air in/out valve assembly
无石棉级摩擦片总成Asbestos-free friction disc assemblage
气胎离合器气囊总成Clutch Ballonet assembly
空气包充气软管总成Charging hose assembly of dampener
热交换器及油标名称Heat exchanger and oil level indicator
配有张力型指重仪表Completed with a tension type weight sensor
大力空压机及压力表Air compressor and pressure gauge
立管压力缓冲器胶杯Standpipe pressure buffer rubber cup
突面钢制管法兰盖板Blind plate
套装内六角扳手Inner hex wrench
转盘下部泥浆回收盘Mud sump under rotary table
照明具备应急功能Lighting, emergency function shall be available.
右钻台偏房为工具房Dog house on the right side of rig floor is a tool house.
液缸由合金锻造而成The hydraulic cylinder is alloy steel forged.
配有天车防碰过卷阀The drawworks is equipped with Crown-O-Matic
安装有接线柱及电缆Complete with all binding posts and cables
总重量(含钻井泵)Total weight(including drill pump)
重量(不含主补芯) Weight(excluding master bushing)
重量(不含液压油) Weight (without hydraulic oil)
液压钻杆钳(备用) Hydraulic drill pipe power tong(standby)
两用水龙头(备用) Dual purpose swivel (standby)
联轴节链轮(马达)Shaft-connecting sprocket (motor)
空压机(英格索兰) Air compressor (Ingersolland )
胶囊(吸入空气包)Capsule(suction pulsation dampener)
管汇(方案布置图) Manifold (Layout)
挂图橱窗(带台边)Picture show window(w/window sill )
工具提篮(配件箱) Junk basket(accessory box)
防滑钩(带保险卡)Anti-slip hook(with safety clip)
顶跨(正面/侧面)Width of top(face/side)
蝶阀箱(一年备件)Butterfly valve case(one year spares)
(一端带直角弯头)(with one 90 degree bend)
(含气瓶及干燥机)(including air tanks and air dryer)
发电、气源房布置图Layout of Generator/Air Source House
井电灯具及配件列表List of lamps and fittings on wellsite
二位三通防爆电磁阀Two-position three -way electromagnetic valve, explosion-proof 电机额定电压/频率Motor rating voltage/frequency
面漆丙烯酸聚氨酯漆Surface painting acrylic polyurethane
地面支座固定座Surface support, fixed
两位两通换向阀组Two-Position Two-Way Reverse Valve set
卡特柴油发电机组CAT diesel generator set
柴油机变矩器机组Diesel torque converter set
风压开关辅件组装Air pressure switch accessory assembling
钻机底座平移装置Rig substructure horizontally sliding device
钻井泵及传动装置Drilling pumps and driving unit
液压盘式刹车装置Hydraulic disc brake unit
液压自动举管装置Hydraulic auto lifting-pipe device
液压猫头固定装置Fastening Unit for hydraulic cathead
泥浆泵及传动装置Mud pump and tansmission device
防坠落及拖拽装置Falling arrester and drag device
绞车盘刹水泵控制Drawworks disc brake water pump control
含蒸汽管线防护罩Including steam pipeline guard
分料箱和转鼓护罩Casing
泵电机风机及护罩Pump motor blower and guard
泥浆泵参数屏电源Mud pump parameter screen power
绞车盘刹水泵电源Drawworks disc brake water pump power supply
指重表齿轮润滑油Gear lube oil,weight indicator
液压离合器涡轮油Turbine oil for hydraulic clutch
减速器传动润滑油Drive lubricant oil of speed reducer
自浮式电子测斜仪Floating electronic inclinometer
硫化氢气体探测仪H2S gas monitor
固控区气体探测仪Gas detection instrument in solid control area
电子单多点测斜仪Electronic inclinometer
便携式HS探测仪HS Detecting Instrument
转盘配以下补芯The rotary table is equipped with the following bushing. 空气过滤器内滤芯Elem. Air fliter fty
空气过滤器外滤芯Elem. Air filter primary
背包绳滑轮固定销Sheeve fixed Pin
远程控制台配件箱Parts box for remote control console
液动手动闸板阀箱Hydrailic/manual gate valve box
液压卷绳机胶管箱Hose box for hydraulic rope spooler
起井架缓冲控制箱Buffer Control Case
卡特柴油机配件箱CAT diesel engine accessaries box
防喷器随机配件箱BOP accessory box
顶驱控制室集装箱Top drive control room container
吊卡及卡瓦随机箱Elevator and slip box
振动筛视频信号线Video signal wire of shale shaker
振动筛视频电源线Power line of shale shaker video
泥浆泵视频信号线Mud pump video signal line
泥浆泵视频电源线Mud pump video power line
泥浆泵电机PE线Mud pump motor PE line
环状活动连接管线Chicksan loop hoses
固控系统各部件图Solid control system parts drawings
高压管汇各部件图Parts Drawing for HP Mud Manifold
转换(由壬)接头Adapter (Union)
油泵出口高压球头HP spherical head, pump outlet
液压油进出口接头Inlet and outlet joints of hydraulic oil
液压马达进油接头Hydraulic motor oil-inlet joint
循环水进出口接头Inlet/outlet Joints for water circulation
刹车泵出油管接头Oil outlet pipe connection of brake pump
刹车泵进油管接头Oil inlet pipe connection, brake pump
刹车泵泄油管接头Oil drain pipe connector, brake pump
美制锥面扩口接头British measurement pyramidal face flared joint
美式强力快速接头American type fast connection
扩口式B型管接头Flared fitting, B-type
可曲挠性橡胶接头Flexible rubber joint
井口防喷装置接头Wellhead BOP joint
接线盒含备用插头Terminal box with spare plug
焊接式铰接管接头Welded Pipe Connector
焊接式直通管接头Through Welded Pipe Connector
焊接式三通管接头Three-Way Welded Pipe Connector
焊接式公由壬堵头Welded male union plug""
不锈钢波纹管接头Stainless steel corrugated pipe connector
井架固定绞链套筒Hinge Sleeve for mast fixation
钻井参数记录系统Recording system for drilling parameters
钻井参数仪表系统Instrumentation system for drilling parameters
气体探测固定系统Gas detection fixed system
动力及电传动系统Power and Electrical drive system
死绳稳绳器3套 3 sets Deadline stabilizer
套管扶正机控制台Casing stabilizer console
套管扶正机维修台Casing centralization machine repairing desk
防喷器安装维护台BOP installation and maintenance platform
真空泵功率/转速Vaccum pump power/rotation speed
BOP用套筒扳手Socket spanner for BOP
定子绕组接线方式Stator winding wireline connection type
登梯助力器斜拉绳Inclined pulling line of Climb assistantor
断路器失压线圈Chopper lose voltage winding,
导线防护橡胶垫圈Rubber gasket, for conductor protection
振动筛磁力启动器Shale shaker magnectic startor
泥浆罐液压传感器Mud level sensor
梅花形弹性联轴器Elastic coupling
交流开关量变送器AC switching value transducer
活绳头绳卡固定器Drill line Fixed Unit
滚筒编码器传感器Drum coder sensor
固定式气体控测器Fixed air detector
供给加速器缓冲器Supply accelerator baffler
防毒面具及过滤器Gas mask and filter
防爆荧光灯镇流器Current stabilizer of Explosion proof fluorescent lamp 多功能保护继电器Multifunction protective relay
超声波液位传感器Ultrasonic fluid level sensor
ISV吸油过滤器ISV oil suction filter
气胎离合器摩擦片Air tube clutch friction block
转向球销锁紧螺母Locknut
梯子(二)与台面Ladder(II)and drilling floor
梯子(-)与台面Ladder(I)and drilling floor
绞车刹车带轴惰轮DW brake idler wheel with shaft
油箱电加热器功率Oil tank heater power
线电压波形畸变率Line voltage wave distorting rate
绞车额定输入功率Drawworks rated input power
换热器热交换功率Heater change power
防爆交流电机功率Explosion proof AC motor power
悬臂吊及电动葫芦Cantilever crane and electric block
SH环链手拉葫芦SH loop chain block
主液压泵额定排量Rated flow rate of main hydraulic pump
液压系统额定流量Hydraulic system rated flow rate
转盘传动箱支承梁Support beam of RT gear box
液缸最高工作压力Max. working pressure of hydraulic cylinder
向传感器提供电力Supply power to sensors
气动系统工作压力Air system working pressure
内防喷器工作压力IBOP Pressure Rating
顶驱最大提升能力Max. lifting Capacity of top drive
泥浆泵电机主电缆Mud pump motor main cable
液压油进出口法兰Inlet and outlet Flanges of hydraulic oil
循环水进出口法兰Inlet/outlet Flanges for water circulation
蓄能器过滤器油块Accumulator filter block
井架专用钢管管卡Special steel pipe clamp for mast
井架安装专用工具Special tools for mast installation
短时最大工作扭矩Short time max working torque
适用的钢丝绳直径Wireline dia.
上水管线油壬短节Water pipeline union sub
法兰由壬过渡短节Flange and union Crossover
钻杆吊卡随机配件Parts delivered together with DP elevator
游动系统安装配件Parts for traveling system installation
移送气缸装置部件Moving cylinder (pneumatic) parts
移动模块安装配件Installation accessories for moving module
压力表接头组合件Connector subassembly, pressure gauge
气源系统安装配件Installation accessories of air source system
联接管路焊接部件Pipe-connecting welding part
进油接头焊接部件Oil input joint welding part
回油接头焊接部件Oil welding joint parts
固控系统成套辅件Solid control System complete accessories
固控系统一年备件One year spares of solid control system
发电机组安装配件Installation fittings of generator set
宝鸡防水防暴插件Water and explosion proof plugs, Baoji
加料漏斗上药品架Pill rack on pill hopper
热交换器换热面积Heat exchanger area
螺杆式空气压缩机Srew type air compressor
绞车辅助驱动电机Drawworks auxiliary driving motor
电动螺杆式压缩机Electrical screw compressor
YJ系列交流电机YJ Series AC Motor
高压油泵柱塞弹簧HP oil pump plug spring
转盘梁最大静负荷Max. static load of rotary table beam
泥浆泵参数屏信号Mud pump parameter screen signal
螺杆空气压缩型号Model of srew type air compressor
泥浆泵参数信号柜Mud pump parameter signal cabinet
泥浆泵冷却小水罐Mud pump cooling water tank
固控系统振动筛罐Share shaker tank of solid control tank
一层钢丝编制胶管Rubber hose, with one steel-line-knitted layer 型可曲挠橡胶接管Type flexible rubber connecting pipe
吸入罐外置连通管Suction tank outfitting connection pipe
稳压电源保险丝管Stabilized voltage power fuse tube
机房用气输出胶管Air output hose for machine house
钢丝编织护套胶管Rubber hose
法兰连接金属软管Metal hose for flange connection
不锈钢丝护套胶管Stainless wire jacketed hose
高压跳脱保护开关High-pressure tripping protective switch
上下底座连接撑根Connecting supporting pole between upper and lower bases
液压钻杆钳移送缸Liquid Pressure Cylinders
井架、底座液压缸Mast and substructure Hydraulic Cylinder
泥浆泵护罩支承杆Mud Pump Shield Rods
突面钢制管法兰盖Blind plate
司钻房和司钻偏房Integrated console/control house and Doghouse Cubicle(driller's cabin)
电动压风机气源房Air Compressor House
VFD/MCC房VFD/MCC house
滚子补芯四销六方Roller bushing pin hex
钻机主要技术规范Main technical specification of drilling rig
双功能箭形回压阀Back pressure valve
防爆电磁换向气阀Ex proof electromagnetic change valve
内六角圆柱头螺钉Inner hexagon cheese head screw
扁平头半空心铆钉Rivet
坡道梯子逃生跑道Ramp ladder escaping way
配套清单Parts list
工具房遥控器钥匙Remote control key of tool house
钻台阀组组件总成Drill floor valve assembly
振动筛排砂槽总成Sand-removing ditch assembly of shale shaker
异型三通组件总成Reducer tee subassembly
万向轴十字轴总成Cardan shaft crosshead Assembly
双单向阀阀块总成Dual-Check Valve Block Assembly
泥浆泵拔缸器总成Mud Pump Seat Fixing Tool
猫头油缸连接总成Connection Assembly for Cathead Cylinder
离心机旋转件总成Centrifuge ROTATING PARTS ASSEMBLY
胶管安全装置总成Hose safety device assembly
电磁刹车手柄总成Electromagnetic Braker Control Handle
地面阀组组件总成Ground valve set assembly
地面阀组底座总成Skid assembly of Ground valve group
除泥器排砂槽总成Desilter sand trough assembly
除砂器排砂槽总成Desander/dump assembly
排砂槽三角架支撑Sand discharging groove tripod
电极和油泵支支撑Generator and oil pump supporter
名称Name
风冷电磁涡流刹车Air cooled eddy current brake
单轮链环起重滑车Pulley of single sheave
0.5T风动绞车0.5T air winch
油壬式抗震压力表EP pressure gauge, union type
由壬式抗震压力表EP pressure gauge,union type
双刻度抗震压力表Dual-scale shockproof pressure gauge
空气进出口温度表Air inlet/outlet thermometer
泥浆清洁器供液泵Mud cleaner feed pump
压力调节器维修包Repair kit for pressure regulator
进气提升阀维修包Kit. Rep 4 INL VLV
死、活绳固定压板Drill line Fixed Blocks
所有交流电机防爆All AC motors are explosion proof type.
带双向气动旋扣器With double direction air make-up device
轴承(固相输出)Bearing(solid output)
轴承(液相输出)Bearing(liquid output)
终端电阻(进口)Terminal resistor(imported)
直管总成(双公)Straight pipe assembly (double pins)
振动筛(直线型) Shale shaker (linear type)
由壬接头(丝扣)Union(thread )
以太网线(低温) Ethernet lead(low temperature)
小杂件(活绳头)Accessories (live line head)
砂泵(一年备件)Sand pump(one year spares)
钳工锉(带木柄)Fitter file(with wood handle)
配件箱一年配件)Accessory box one year spares)
猫道(含钻杆架) Catwalk channel(includs pipe rack)
喇叭口(选配项) Bell nipple(for option)
缓冲垫(安全阀)Buffer pad(safety valve)
滚子补芯(一套) Roller bushing(1 set)
挂钩(带安全舌)Hook(with safety pin)
(含辅助发电机)(including an auxiliary generator)
(不包括消声器)(except the muffler)
最大举升管子质量Max. mass of lifted pipe
最大举升管子长度Max. length of lifted pipe
最大举升管子直径Max. diameter of lifted pipe
主液压泵额定压力Rated pressure of main hydraulic pump
主液压泵电机功率Motor power of main hydraulic pump
液压系统额定压力Hydraulic system rated pressure
凸面带颈平焊法兰Downward welding flange
空气过滤器修理包Air filter maintainance kit
底座配以下附件The substructure is provided following accessory 斜拉杆与上下座Inclined tension rod and upper &lower seats
泥浆泵调节底座Mud pump Adjustable skid
井架连接双耳座Dual Eyepad Seat For mast-connecting
防喷管线固定座Choke Manifold Fixed Seat
防喷器运载底座Carrying seat of BOP
保温棚柱与底座Insulated booth poles and base
Ⅱ级托板后支座Grade II pallet rear support
直接式黄油油嘴Straight grease nipple
钻台H型闸门组H gate valve unit on drill floor
蓄能器过滤器组Accumulator filter set
泥浆泵电动机组Rig pump driving unit-DC motor
井架起升滑轮组Mast lifting sheaves set
节流管汇闸阀组Choke manifold gate valve set
地面管汇闸阀组Gate valve set of ground manifold
比例溢流阀阀组Proportional Relief valve set
输出虑波器电阻Output wave filter resister
逃生滑道及梯子Escape slide and ladder
排砂槽总成梯子Sand discharging groove assembly ladder
二层台栏杆销子Pins for Racking board handrail
液压大钳尾绳柱Snub line stake, hydraulic power tong
钻井泵传动装置Mud pump transmission device
转盘及驱动装置Rotary table and driving device
主补芯吊装装置Lifting device for master bushing
套管灌泥浆装置Casing mud charge unit
泥浆泵传动装置Mud pump drive device
泥浆泵控制装置Mud pump controlling device
立根防坠落装置Pipe Falling arrester
井架工安合装置Derrickman safety device
辅助蓄能器装置Assistant Accumulator Set
防喷器起吊装置Lifting unit of BOP
防喷器吊装装置Hoisting device of BOP
防喷器移动装置BOP trolley
防喷器吊装装置BOP lifting device
防碰器吊装装置BOP hoisting unit
防喷器导轨装置BOP guide rail device
二层台逃生装置Racking board escaping device
二层台拖曳装置Drag device on racking board
大钳平衡重装置Tong counterweight
差速防坠落装置Speed-reduce anti falling device
板式水冷却装置Water Cooling Unit of plate type
BOP控制装置Bop control unit
低温极压润滑脂Low temperature extreme pressure grease 绞车联轴器护罩DW Coupling Guard
电机联轴器护罩Motor Coupling Guard
立根盒最大静载Max.static setback load
防爆照明箱电源Power supply for Explosion proof lighting box 钻杆扶正台备用DP stabbing board, standby
油气分离器滤芯Oil-gas separator filter element
油气分离器滤芯Filtrating element of oil/gas separator
沙漠型空气滤芯Air Filters
燃油滤清器滤芯Fuel filter element
空气过滤器滤芯Air filter element
卡特发电机滤芯CAT generator filter element
机油滤清器滤芯Oil filter element
回油滤油器滤芯Oil return filter element
回油过滤器滤芯Oil return filter element
高压过滤器滤芯High pressure filter element
消防工作服帽鞋Fire Fighting Clothes
自动送钻减速箱Huto-bit-feed speed reducer casing
双闸板防喷气箱Double ram BOP box
井架销轴配件箱Pin accessaries box of mast
固控系统胶管箱Solid control system rubber hose case 防暴动力接线箱Explosion proof power junction box
防暴照明接线箱Explosion proof lighting junction box
顶驱配件集装箱Top drive accessory container
底座销轴配件箱Substructure pins box
测井绞车配件箱Accessories box of logging winch
2T电动葫芦箱2T electric Hoist
转盘电机PE线PE wire of RT motor
振动筛外置管线Shale shaker external pipe
泥浆泵排出管线Mud pump discharging pipeline
内防喷高压管线Inner blowout preventing HP pipeline
立管压力表管线Standpipe pressure gauge line
绞车电机PE线Drawworks motor PE line
弹簧,笔杆回位Spring, Pen Arm Return
钻机气路安装图Air piping diagram for rig
两用水龙头总图Dual purpose swivel general drawing
井架气路安装图Mast air course installation drawing
绞车气路安装图DW air pipeline installation drawing
电动机机结构图Motor structural drawing
电动倒绳机总图Electric wireline spooler general drawing 电动倒绳机总图Electric Wireline Spooler
自封式快换接头Self-sealing quick release joint
预绝缘管状端头Pre-insulated tubular end
溢流阀回油接头Relief valve retrun-oil joint
一端带直角弯头With elbow at one end
压力开关焊接头Welded joint, pressure switch
压力表过渡接头Pressure gauge crossover sub
压盖式伸缩接头Flex joint
无缝同心大小头Concentric Seamless Reducing Bushing 水龙头保护接头Swivel Saver Sub
水龙头转换接头Swivel adaptor
气体探测仪探头Gas detector probe
泥浆储备罐弯头Elbow for reserve tank
滤油器进油接头Oil filter inlet connector
连接器,公接头Coupling, Male Disconnect
连接器,母接头Coupling, Female Disconnect
快插式螺纹接头Quick threaded connector
快拔接头,公头Quick connector, male
快拔接头,母头Quick connector, female
可曲挠橡胶接头Flexible rubber joint
方钻杆保护接头Kelly protection joint
传感器焊接接头Sensor joint, weld type
冲压焊接式弯头Punch welding type elbow
冲压焊接式弯头punch welding type elbow
超高压快速接头Extra-high voltage quick connector
不锈钢快换接头Quick release coupling, stainless steel
T形快插式接头Push-in fitting of T-shape
T形插入式接头Push-in fitting of T-shape
液压站电气系统Eelectric system of HPU
防喷器调装系统BOP lifting system
防喷器吊装系统BOP hoisting system
发电机控制系统Generator Control System
中间漆环氧云铁Intermediate paint, epoxy micaceous iron oxide 下O型密封压套Lower O seal pressure sleeve
联轴器柱销,套Pins and sheath loops
液压套管扶正台Hydraulic casing stabbing board
机房压板及螺丝Engine Fixed Blocks and Bolts
主绞车固定螺栓Lock bolts of drawworks
封井器双头螺栓Bolt for BOP
除气器配件螺栓Degasser accessory bolt
泥浆化学实验室Mud laboratory
接线盒至办公室Terminal box to office
刹车盘冷却方式Cooling type of brake disc
井口溢流管吊绳Wellhead overflow pipe hoisting line
北石所液压盘刹Drawworks
自封式锤击由壬Hammer union, self-seal type
焊接式球面由壬Welded spherical union
锤击式钢制由壬Impact steel union
发电机照明加热Generator lighting heating
圆螺母止动垫圈Nut Stop Washer
由壬接头密封圈Union seal ring
猫头配件密封圈Cathead accessory sealing ring
断路器失压线圈Circuit voltage lose loop
断路器分闸线圈Circuit switch off winding
大钳全套密封圈All set of seal rings of tongs
大钳全套密封圈 A complete set of power tong sealing rings
除气器配件垫圈Degasser accessory gasket
O型橡胶密封圈O-ring
O形橡胶密封圈O-ring
二层台及挡风墙Racking board and windshield
脚踏气压黄油枪Treadle type grease gun
直嘴孔用卡簧钳Spring caliper
液压钻杆动力钳Hydraulic drill pipe power tong
分气筒液气大钳Air divider hydraulic pneumatic tong
B型吊钳扣合钳 B type suspending tongs closing wrench B型吊钳扣合钳 B type manual tongs closing wrench
自耦降压启动器Startor
转盘转速传感器Rotation speed sensor of RT
转盘扭矩传感器Rotary torque sensor
直梯攀升保护器Protector for climbing straight ladder
游车位置传感器Travelling block position sensor
位移信号处理器Location signal processing unit
外围配套传感器Peripheral sensors provided
送钻电机编码器Bit feeding motor coder
起升大绳悬挂器Hanger of hoisting rope
泥浆气体分离器Poor Boy Separator
泥浆压力传感器Mud pressure sensor
泥浆实验室仪器Mud lab instrument
泥浆液气分离器Mud Gas Separator
模拟信号变送器Anolog signal transducer
立管压力传感器Stand pipe pressure sensor
乐清力士差速器Differential
交流线路保护器AC line protector
机具回油过滤器Oil return filter
鼓形齿式联轴器Drum shape toothed coupling
隔离栅,报警器Separation fence, alarm
防爆温度传感器Temperature sensor, EX-PRF
防爆液位传感器Liquid level sensor, EX-PRF
防爆液位控制器Liquid level controller,EX-PRF
防爆磁力启动器Explosion protecting starter
防暴磁力启动器Explosion proof magnetic starter
防爆报警发生器Explosion proof alarm
防爆型电加热器Electrical heater, EX-PRF
防爆空气冷却器Air cooler, EX-PRF
弹性柱销联轴器Resilient coupling with cylindrical pin
大钳扭矩传感器Tong torque sensor
大钩钩载传感器Hook load sensor
传动轴及联轴器Drive shat
出口流量传感器Displacement sensor
VFD房灭火器VFD house fire extinguisher
气动导管钳主气Air powered duct wrench
液位传感器垫片Shim for liquid level sensor
无石棉级摩擦片Non asbestos friction pad
气动锚头摩擦片Friction Piece for CatHead
多针型阀岛阀片Multiple-pin valve terminal valve plate
气胎离合器气囊Air tube clutch air bag
扩口管接头螺母JICflared tube connector nut
立管操作台台面Standpipe Operation Platform board
常闭气控阀或门Long close air control valve or gate
液压站电气编码Code of electric system of HPU
二层台导向滑轮Racking board guide pulley
配搅拌器功率Agitator power
离心泵电机功率Centrifugal motor power
技术文件及资料Technical documents and files
最大泥浆处理量Max.mud processing capacity
最大气体处理量Max.air processing capacity
压缩机额定排量Compressor rated displacement
刹车蓄能器容量Brake accumulator capacity
混合漏斗处理量Mixing hopper capacity
供水离心泵数量Water supply centrifuge number
二层台立根容量Stands capacity on racking board
除砂旋流器数量Desander cyclone number
除泥旋流器数量Cyclone number
右基座及转盘梁Right base seat and rotary table beam
中心管工作压力Working pressure of stem
刹车额定正压力Rated positive pressure of brake
发电机负载能力Capacity of generator sets
电池组的总能力Battery set capacity
传感器输出压力Output pressure of sensor
综合液压站原理Working principle of combined HPU
转盘电机主电缆Main cable of RT motor
泥浆泵电机电缆Mud pump motor cable
泥浆泵电机电缆Mud pump motor cable
绞车电机主电缆Drawworks motor main cable
凸面钢制管法兰Convex steel pipe flange
滤油器法口法兰Oil filter outlet flange
加油过滤器法兰Oil filling filter flange
机具泵出油法兰Oil outlet flange of machinery tool pump
机具泵吸油法兰Oil inlet flange of machinery tool pump
防喷器连接法兰BOP connecting flange
发动机连接法兰Connection flange of engine
井架起、放工况Working condition of mast lifting and lowering 下导向器固定块Lower Guide Retainer
比例溢流阀阀块Valve block, proportional relief valve
开式索具螺旋扣Opened rigging
带螺母弓型卸扣Arc style screw off with nut
空气进(出)口Air inlet(outlet)
上下构件连接卡Connecting clamp
侧开式套管吊卡Side open Casing Elevator
钻井泵专用工具Pump tools
配套电器及布局Equipped electric apparatus and layout
钻井钢丝绳直径Dia. Of drilling line
主气路管线管径Diameter of main air line
吸入管尺寸内径ID of exhaust pipe
适用钢丝绳直径Suitable wire diameter
排出管尺寸内径ID of suction pipe
捞砂钢丝绳直径Dia. of sand wireline
除砂旋流器直径Desander cyclone diameter
除泥旋流器直径Cyclone diameter
方钻杆保护短节Kelly protection nipple
配电箱固定底脚Switch box fixed leg
乐泰厌氧密封胶Sealant
油泵联轴器部件Parts for oil pump coupler
油箱盖焊接合件Oil box cover welded part
气源处理三联件 3 in 1 air source treatment device
泥浆罐安装配件Mud tank installation accessories
记数器滑块部件Counter sliding block parts
计数器滑块部件COUNTER SLIDIGN BLOCK PARTS
缓冲装置固定件Snubber assembly fixture
滚筒端头延伸件Extension piece of drum end
钢箍连接杆组件Connecting parts of steel hoof
防水型9芯插件Waterproof 9-core plug-in
档绳罩焊接部件Blocking-wire-cover welding part
自动灌浆罐底架Base skid, automatic filling tank
振动筛罐话机架Phone holder, shale shaker
司钻房起升支架Driller's hoisting frame
气体探测仪支架Gas detector support
泥浆储备罐底架Mud reserve tank bottom support
立支架与斜支架Vertical supporting frame and inclined supporting frame 可调式井架支架Adjustable mast bracket
井架起升人字架Mast lifting A-frame
二层台吊装支架Lifting frame on racking board
登梯助力器支架Support of climb assistantor
除沙除泥器支架Desander& desilter combined cleaner support
接线盒防护等级Terminal box protection level
系统总有效容积System total capacity
空气储罐组容积Air tanks total capacity
钻井泵驱动电机Drilling pump motor
液压套管扶正机Hydraulic casing stabbing device
液压工具提升机Hydaulic tool-hoister
同绞车驱动电机The same as motor of drawwork
螺杆空气压缩机Srew type air compressor
高压设备清洗机High Pressure Washing Equipment
钢丝绳及倒绳机Wireline and spooler
钢丝绳及倒绳机Wire line and spooler
电动螺杆空压机Electric screw air compressor
除砂除泥一体机Desander and disilter integrative cleaner
超G力振动电机Super G power vibrating motor
侧进风变频电机Side intake VF motor
摆线针轮减速机Cycloid speed reducer
VFD房工控机VFD house industry computer
除沙除泥一体化Desander& desilter combined cleaner
灌注泵离心型号Charge pump centrifuge model
发运地点广汉Delivery site: Guanghan
防爆开关控制柜Explosion proof switch control cabin
防爆开关控制柜EX switch control cabinet
固控系统吸入罐Suction tank of solid control system
固控系统储备罐Storage tank of solid control system
固控系统混浆罐Solid control system mixing tank
真空除气器弯管Bend pipe, vacuum degasser
一层钢丝编织管Rubber hose, with one steel-line-knitted layer 液压马达溢流管Hydraulic motor flow line
砂泵吸入四通管Sand pump suction four-way pipe
泥浆枪连接软管Mud gun connecting hose
连接绞车线槽管Cable channel to DW
井口至罐过浆管High Mud Pipe
进罐(下)胶管Inlet hose(bottom)
混合漏斗进液管Amalgamate Hopper fluid-in manifold
腐蚀罐进液软管Chemical tank inlet hose
分离器管线弯管Mud Gas Separator Pipes elbow
分离器管线直管Mud Gas Separator Pipes
反循环高压软管High pressure hose
电磁刹车中心管Electricomagnetic brake central tube
带由壬中压胶管Middle Pressure Hose with union
C型扣压式胶管 C type press rubber hose
A型扣压式胶管Rubber pipe assembly of A-type
A型扣压式胶管Rubber pipe assembly A-type
防爆型压力开关Explosion proof pressure switch
电机的风压开关Air pressure switch of motor
断路器操作机构Circuit breaker operation
无钩载,满立根No hook load, full of stands
支座式二位气缸Bracket type 2-position cylinder
安装法兰/气缸Flange/Cylinder
溢流管及方钻杆Flow line and kelley
液体分离器螺杆Screw rod for liquid separator
液压大钳加长杆Extension lever for hydraulic power tong
井架大腿横拉杆Mast main leg cross tie-rod
保温棚底座撑杆Base supporting pole of insulated booth
机械类常用英语词汇大全 一字螺丝批 slot type screwdriver 一点透视 one-point perspective 二画 二合一黏合剂 epoxy resin adhesive 二合胶;混合胶 epoxy glue 二维的;平面的 two-dimensional 二进制 binary 二极管;整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的;公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学 ergonomics; human engineering 人体尺寸 human dimension 人体测量学 anthropometry; anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷;床鞍 apron 刀座鞍;溜板座 saddle 力 force 力三角形 triangle of force 力平行四边形 parallelogram of force 力多边形;多边形力学 polygon of force 力的分解 force resolution 力架;亮漆 lacquer 力矩 moment 力偶 couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip s head screw 十字螺丝批 Philip s type screwdriver 丁字尺;T 尺 tee square 三画 三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的;立体的 three-dimensional 三氯甲烷;哥罗芳 chloroform 三聚氰胺;蜜胺 melamine 三点透视 three-point perspective 上油漆 painting 上釉 enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力;虫漆 shellac 士巴拿;扳手 spanner 大芯夹板;宽条芯夹板 blockboard; solid corestock-laminated board 大量制造 mass production
密闭式炼胶机械 密(闭式)炼(胶)机internal mixer 翻转式密炼机dispersion mixer 加压式捏炼机pressurized kneader 总容积net chamber volume 工作容积working volume 填充系数filled coefficient(工作容积/总容积)转子速比rotating speed ratio of rotors 左传动left-hand drive 右传动right-hand drive 密炼室mixing chamber 正面壁chamber side 侧面壁chamber end 转子rotor 椭圆形转子elliptical type rotor 圆柱形转子cylindrical type rotor 相切型转子tangential rotor 啮合型转子intermeshing rotor 同步技术转子synchronous technological rotor 转子凸棱wing, nog 转子密封装置dust stop of rotor 加料门feed hopper door 压料装置pressing ram device 压砣ram 卸料装置discharge device 滑动式卸料装置slide door discharge device 摆动式卸料装置drop door discharge device
卸料门discharge door 翻转装置tilting device 上辅机up-stream equipment 下辅机down-stream equipment 胶片冷却装置batch off unit, slab cooling unit 开放式炼胶机械 开(放式)炼(胶)机mill, two-roll mill 压片机sheeting mill 热炼机warming mill 破胶机breaker 粉碎机grinding mill 粗碎机cracker 洗胶机washing mill, washer 精炼机refining mill, refiner 辊距nip, gap 辊隙nip, gap (辊筒)速比linear speed ratio (of rolls),friction ratio (of rolls)横压力separating force 辊筒roll 辊面宽度roll surface width 中空辊筒bored roll 钻孔辊筒drilled roll 沟槽辊筒fluted roll 前辊筒front roll 后辊筒rear roll, back roll 压盖frame cap
抛光 polishing 安装 to assemble 扳手 wrench 半机械化 semi-mechanization; semi-mechanized 半自动滚刀磨床 semi-automatic hob grinder 半自动化 semi-automation; semi-automatic 备件 spare parts 边刨床 side planer 变速箱 transmission gear 柄轴 arbor 部件 units; assembly parts 插床 slotting machine 拆卸 to disassemble 超高速内圆磨床 ultra-high-speed internal grinder 车床 lathe; turning lathe 车刀 lathe tool 车轮车床 car wheel lathe 车削 turning 车轴 axle 衬套 bushing 按英文字母排序 3-Jaws indexing spacers 三爪、分割工具头 A.T.C.system 加工中心机刀库 Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备 Bayonet 卡口 Bearing fittings 轴承配件 Bearing processing equipment 轴承加工机 Bearings 轴承 Belt drive 带传动 Bending machines 弯曲机 Blades 刀片 Blades,saw 锯片 Bolts,screws & nuts 螺栓,螺帽及螺丝 Boring heads 搪孔头 Boring machines 镗床 Cable making tools 造线机 Casting,aluminium 铸铝 Casting,copper 铸铜 Casting,gray iron 铸灰口铁 Casting,malleable iron 可锻铸铁
C型胶管(一端带直角弯头)Rubber pipe assembly, C-type(with an elbow, 90°) 上部内防喷器接头(远控) Upper IBOP (remote) 主机防风棚可燃气体探测仪Inflammable gas detector in main equipment shed YM-16-Ⅱ型液压猫头YM-16-Ⅱ Hydraulic Cathead 主发电机组额定功率×台数Rated power X quantity, main generator set 将所有DAQ数据存于硬盘Store all DAQ data on hard disk. 由任式金属硬密封泥浆阀门Mud valve , union type, metal to metal seal 焊拉式金属硬密封泥浆阀门Welding metal seal mud valve 焊接式金属硬密封泥浆闸门Welding metal rigid mud-sealing gate 焊接式金属硬密封泥浆阀门Welded metal hard sealing mud valve 底部压井管线包括四个阀门Kill line(including 4 valves) API阀门DN50组数量API gate valve DN50 union 刹车液压操作系统额定压力Rated hydraulic operation system pressure of brake 金属硬密封泥浆阀门密封件Metal hard seal mud valve sealings 设计符合API4F规范The mast conforms to API 4F 设计符合API9B规范Conforms to API 9B 设计符合API8A规范Conforms to API 8A specification 设计符合API7K规范Conforms to API 7K specifications 柴油发电机组保养配件清单Maintenance parts list of diesel generator set house 司钻控制室及钻井参数仪表Driller's control cabin and drilling parameter instrument 焊接式金属硬密封泥浆阀板Welding metal seal mud valve plate 每个泵上的三个缸可以互换The 3 hydraulic cylinders of every pump can be interchanged. 操作台升降行调节范围6m Console rising and lowering distance is 6m 带传动,以简化减速机构. Belt transmission is adopted, which simplifies the speed-reducing mechanism. 主滚筒尺寸(直径×长度)Main drum size(Dia.×Length) 压力差开关(油气分离器)Pressure difference switch (oil-gas separator) 旋转方向(面向飞轮端视)Rotation direction(facing to flywheel) 橡胶管线1""(约30米)Rubber pipe line1""(About 30 m) 推拉式塑钢窗(钢化玻璃) Slide plastic-steel window (tempered glass) 刹车鼓尺寸(直径×长度)Brake rim size(Dia.×Length) 排出滤网及辅助管路(二)Discharge Filter Screen and Assistant Pipe(2) 空气过滤器滤芯(重负荷)Air filter element(heavy duty) 胶管总成(长度仅供参考)Rubber hose assembly(Length for reference) 电传系统部分(发电机柜)Electric drive system(generator cabinet) 电传系统部分(开关柜)Electric Drive System(Cubicle Switchboard) 打捞震击器(液压上击器)Fishing jar 不锈钢丝护套胶管(横向) Stainless wire jacketed hose(horizontal) 不锈钢丝护套胶管(横向)Stainless wire jacketed hose(cross) (5″钻杆28米立根)(5"drill pipe 28m stand) 四川宏华石油设备有限公司Sichuan Honghua Petroleum Equipment Co., Ltd. 发电、气源房布置各部件图Parts drawing for Generator/air source house 钻井液管汇通径/额定压力Drilling fluid manifold bore size / rated pressrue
机器制造工业машиностроительная промышленность 机床;工作母机станок 重型机床станок тяжелого типа 精密机床прецизионный(точный)станок 自动程序控制机床станок с автоматеческим программным управлением 量具刃具мерительные и режущие инструменты 轴承(滚珠轴承,滚针轴承,微型轴承) подшипник(роликовый,игольчатый,микро-подшиник) 试造车间экспериментальный цех 制模车间модельный цех 翻砂(铸造)车间литейный цех 锻工车间кузнечный цех 冷锻车间холодноштамповочный цех
热压车间цех горячей прессовки 热处理车间термический цех;цех термической обработки 木工车间деревообделочный цех 铜工车间медный цех 油漆车间малярный цех 量具车间цех мерительного инструмента工具车间интрументальный цех 大件装配车间сборочный цех крупных деталей 装配车间сборочный цех 辅助车间вспомогательный цех 修配车间ремонтно-монтажный цех 铸造设备литейная установка 辗压设备каточная установка 金属切削机床металлорежущий стан 车床станок 齿轮箱车床токарный станок с коробкой
石油工程专业英语单词 A abnormal pressure异常高压 absolute open flow potential绝对敞喷流量 absolute permeability绝对渗透率 acetic acids乙酸 acid-fracturing treatment酸化压裂处理 acidize酸化 acidizing酸化 additives添加剂 Alkali/Surfactant/Polymer( ASP) tertiary combination flooding三元复合驱anhydrite无水石膏 annular space环形空间 appraisal well估计井,评价井 aquifer含水层 areal sweep efficiency面积波及系数 artificial lift methods人工举升方法 B beam pumps游梁式抽油机 bitumen沥青 blast joint耐磨钻头 block and tackle滑轮组 blowout preventes防喷器 blowout井喷 bone strength胶结强度 borehole井筒,井眼 bottomhole/wellhead pressure井底 / 井口压力 bottorm water底水 breakthrough突破,穿透 bubble point泡点 bubble point pressure泡点压力 C cable tool drilling顿钻钻井 capillary action毛细管作用 carbonate reservoirs碳酸盐储层 casing hanger套管悬挂器 casing head套管头 casing collapse套管损坏 casing corrosion套管腐蚀 casing leak 套管漏失 casing pressure套管压力
机械英语词汇大全2 金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 拉孔 broaching 装配 assembling 铸造 found 流体动力学 fluid dynamics 流体力学 fluid mechanics 加工 machining 液压 hydraulic pressure 切线 tangent 机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure 稳定性 stability 介质 medium 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking 技术要求 technical
机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist 弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve 失效 invalidation 强度 intensity 载荷 load 应力 stress 安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix 键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮
机械专业词汇 速度:Geschwindigkeit 动量:Bewegungsgroesse 摩擦:Reibung 动能:kinetische Energie 碰撞:zusammenstossen 质点:Partikel 抛物线:Parabel 万有引力:Gravitations 定理:Gesetz 光波:lichtwelle 波长:wellenlaenge 波:Welle 横波:Ouerwelle 纵波:laengswelle 场强:Feldstaerke 电势:elektrisches Potenzial 电势差:Potenzialdifferenz 电容:Kapazitaet 反向电流:inverser Strom gegenstrom 结构分析:strukturanalyse 自由度:Freiheitsgrad 转动:drehen 电路:Stromkreis 电压:Spannung 交变电流:wechselstrom 直流电流:Gleichstrom 节点:Gelenk 支路:nebenstrasse Seitenstrasse
电源:Stromquelle 互导:steilheit 互感:Gegeninduktion 电桥:Brueckenschaltung 电桥臂:Bruechenarm 尺寸公差:Toleranz 基本尺寸:grundmass 极限尺寸:Grenzmaass 偏差:Abmass 配合:zusammenspiel 公差带:Toleranz breite 公差带及配合:spielsitz 孔:Loch 轴:Achse 基孔制:Einheitsbohrung 基轴制:Bezugsachse 总和:Gesamtheit 俯视图:Aufsicht 视图:Ansicht 前视图:Vorderansicht 侧视图:Seitenansicht 三维:dreidimensional 切削:spanen schneiden 刀具: Stahl meissel 切削方向:Schnittrichtung 切削液:Schneidwasser 切削加工:Spanende bearbeitung 切削速度:schnittgeschwindigkeit 切削面:schnittflaeche 切削性:schneidbarkeit
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ;normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ;Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图 Conveyer流水线物料板Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检 查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压 测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检 查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产 部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备
石油词汇大全俄语专业 词汇 文稿归稿存档编号:[KKUY-KKIO69-OTM243-OLUI129-G00I-FDQS58-
石油词汇大全----俄语专业词汇 油田,油矿нефтепромысел 油井нефтескважина 石油产地нефтяное месторождение 石油产区нефтеносный район 钻井бурение 输油管道нефтепровод 贮油罐сборный резервуар 石油加工нефтепереработка 炼油厂нефтеочистительный завод 石油产品нефтепродукт 汽油бензин 柴油дизельное топливо 煤油керосин 重油мазут 沥青битум 石蜡парафин 凡士林(油)вазелин 润滑油смазочное масло 索拉油(太阳油)соляровое масло 润滑脂(黄油)тавот 石油焦нефтяной кокс 芳香族石油ароматическая нефть 含水石油обводнённая нефть 脱水石油обезвоженная нефть 奥别尔过磷酸钙оберфос 脱盐石油обессолённая нефть 石油基地нефтебаза 石油沥青нефтебитум 油轮нефтевоз 油港нефтегавань 石油汽нефтегаз 石油开采工нефтегазодобытчик 石油天然汽开采нефтегазодобыча 石油含量нефтегазоносность 石油天然气管道нефтегазопровод 集油器нефтеловушка
机械工具 扳子spanner (美作:wrench) 敲击扳手Impact spanner 双头扳子double-ended spanner 活扳子,活络扳手adjustable spanner, monkey wrench 套筒扳手box spanner (美作:socket wrench) 卡规calipers 夹钳pincers, tongs 剪床/大剪刀shears 钢锯hacksaw 剪线钳wire cutters 万能手钳multipurpose pliers, universal pliers 可调手钳adjustable pliers 冲子punch 钻drill 麻花钻Twist drill 螺纹thread 丝锥threader 丝锥tap 板牙spanner 板牙mastertap 绞刀(扩孔钻) reamer 柱绞刀cylinder reamer 锥绞刀taper reamer 卡盘chuck 三角刮刀scraper 孔径规calliper gauge 铆钉rivet 螺母nut 自锁螺母,防松螺母locknut 螺栓bolt 销钉pin, peg, dowel 垫圈washer U形钉staple 注油枪grease gun 撬棍Tommy bar, crow bar 防震橡胶锤rubber dead blow hammer 手动葫芦(倒链) manual hoister 机械加工拋光polishing 安装to assemble 衬套bushing 半机械化semi-mechanization; semi-mechanized 半自动滚刀磨床semi-automatic hob grinder 滚刀hob 扳手wrench 1
机械专业英语词汇(大全) 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性 elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析 力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲 应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度 rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 铰孔 fraising 铰刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮 gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck 加工中心machining center 车刀lathe tool 车床lathe
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42
43 44 45 46 47 、三氯甲烷;哥罗芳 chloroform 48 、三聚氰胺;蜜胺 melamine 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84
86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125
126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 、勾;勾脚 hook 152 、勾刀;胶片刀 plastic cutter 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167
169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209
组装、冲压、喷漆等专业词汇 Assembly line 组装线Layout 布置图 Conveyer 流水线物料板Rivet table 拉钉机 Rivet gun 拉钉枪Screw driver 起子 Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查 fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合fuse machine 热熔机 repair 修理operator 作业员 QC 品管supervisor 课长 ME 制造工程师MT 制造生技 cosmetic inspect 外观检查inner parts inspect 内部检查 thumb screw 大头螺丝lbs. inch 镑、英寸 EMI gasket 导电条front plate 前板 rear plate 后板chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件SOP 制造作业程序 material check list 物料检查表work cell 工作间 trolley 台车carton 纸箱 sub-line 支线left fork 叉车 personnel resource department人力资源部production department 生产部门planning department 企划部QC Section 品管科 stamping factory 冲压厂painting factory 烤漆厂 molding factory 成型厂common equipment 常用设备 uncoiler and straightener 整平机punching machine 冲床
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
石油英语词汇(P5) POL 面向问题的语言 polar activation 极性活化 polar adsorption 极性吸附 polar air mass 极地气团 polar angle 极角 polar anticyclone 极地反气旋 polar attraction 极性引力 polar cap absorption 极冠吸收 polar chart recorder 极坐标图记录器polar chart 极坐标地图 polar circle 极圈 polar climate 极地气候 polar compound 极性化合物 polar contact 极化继电器触点 polar coordinates 极坐标 polar curve 极坐标曲线 polar diagramm 极坐标图 polar drafter 弧形牵伸装置 polar easterlies 极地东风带 polar end 极性端 polar expansion 线膨胀 polar fluid 极性流体 polar flux 极化磁通 polar form 极坐标形式 polar frequency plot 矢量频率图 polar group 极性基团 polar impurity 极性杂质 polar leakage 磁极漏泄 polar liquid 极性液体 polar material 极性物质 polar method 极坐标法 polar molecule 极性分子 polar monomer 极性单体 polar mount antenna 极座架天线 polar orbit 极轨道 polar organic solvent 极性有机溶剂polar plot 极坐标图 polar polymer 极性聚合物 polar projection indicator 极投影指示器polar projection 极投影 polar racorder 极坐标记录器 polar radiation pattern 极坐标辐射图polar radius 极半径polar ray 极射线 polar region 极地 polar relay 极化继电器 polar solid angle 极隅角 polar solvent 极性溶剂 polar stereographic projection 极射赤平役影polar wandering 极移 polar winding 极向缠绕法;极向卷绕 polar 极的 polar-solvent extraction 极性溶剂萃取法polargraph 极谱仪 polari- 极 polarigraphy 极谱分析 polarimeter 极化计 polarimetric analysis 旋光分析 polarimetry 旋光测定;测极化 polaris 北极星 polarisation 极化 polariscope 偏振光镜 polariscopy =polarimetry polariton 电磁声子;偏振子 polarity chron 极性时 polarity coincidency correlator 极性符合相关器polarity effect 极化效应 polarity encoding 极性编码 polarity epoch 极性期 polarity era 极性代 polarity event 极性事件 polarity hyperinterval 极性特超间隔 polarity indicator 极性指示器 polarity information 极性信息 polarity interval 极性间隔 polarity inversion 极性倒转 polarity mark 极性标记 polarity period 极性纪 polarity reversal 极性倒转 polarity rock-stratigraphic unit 极性岩石地层单位polarity standard 极性标准 polarity subchron 极性亚时 polarity subinterval 极性亚间隔 polarity subzone 极性亚带 polarity superinterval 极性超间隔 polarity time scale 极性年表 polarity 极性