IC datasheet pdf-TRS3223E,pdf(3-V TO 5.5-V MULTICHANNEL RS-232 LINE DRIVER_RECEIVER)

https://www.sodocs.net/doc/135529527.html, FEATURES

APPLICATIONS

DESCRIPTION/DB, DW, OR PW PACKAGE (TOP VIEW)

N.C. ? No internal connection

RHL PACKAGE (TOP VIEW)

CC C1+N.C.V+

C1–

C2+

C2–

V–

DOUT2

N.C.

RIN2Flexible control options for power management are available when the serial port is inactive.The TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION SLLS794–JUNE 2007

?ESD Protection for RS-232Bus Pins

–±15-kV Human-Body Model (HBM)

–±8-kV IEC61000-4-2,Contact Discharge

–±15-kV IEC61000-4-2,Air-Gap Discharge

?Meets or Exceeds the Requirements of

TIA/EIA-232-F and ITU v.28Standards

?Operates With 3-V to 5.5-V V CC Supply

?Operates up to 500kbit/s

?Two Drivers and Two Receivers

?Low Standby Current ...1μA Typ

?External Capacitors ...4×0.1μF

?Accepts 5-V Logic Input With 3.3-V Supply

?Alternative High-Speed Pin-Compatible Device

(1Mbit/s)for TRSF3223E ?

Battery-Powered Systems ?

PDAs ?

Notebooks ?

Laptops ?

Palmtop PCs ?Hand-Held Equipment ORDERING INFORMATION The TRS3223E consists of two line drivers,two line receivers,and a dual charge-pump circuit with ±15-kV ESD protection pin to pin (serial-port connection pins,including GND).The device meets

the requirements of TIA/EIA-232-F and provides the

electrical interface between an asynchronous

communication controller and the serial-port

connector.The charge pump and four small external

capacitors allow operation from a single 3-V to 5.5-V

supply.The device operates at typical data signaling

rates up to 500kbit/s and a maximum of 30-V/μs

driver output slew rate.auto-powerdown feature functions when FORCEON is low and FORCEOFF is high.During this mode of operation,if the device does not sense a valid RS-232signal,the driver outputs are disabled.If FORCEOFF is set low and EN is high,both drivers and receivers are shut off,and the supply current is reduced to 1mA.Disconnecting the serial port or turning off the peripheral drivers causes auto-powerdown to occur.Auto-powerdown can be disabled when FORCEON and FORCEOFF are high.With auto-powerdown enabled,the device is activated automatically when a valid signal is applied to any receiver input.The INVALID output is used to notify the user if an RS-232signal is present at any receiver input.INVALID is high (valid data)if any receiver input voltage is greater than 2.7V or less than –2.7V,or has been between –0.3V and 0.3V for less than 30μs.INVALID is low (invalid data)if the receiver input voltage is between –0.3V and 0.3V for more than 30μs.Refer to Figure 4for receiver input levels.

Please be aware that an important notice concerning availability,standard warranty,and use in critical applications of Texas

Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.

https://www.sodocs.net/doc/135529527.html, TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION

SLLS794–JUNE 2007ORDERING INFORMATION

T A

PACKAGE (1)(2)ORDERABLE PART NUMBER TOP-SIDE MARKING QFN –RHL

Reel of 2000TRS3223ECRHLR PREVIEW Tube of 25TRS3223ECDW SOIC –DW

TRS3223EC Reel of 2000TRS3223ECDWR 0°C to 70°C Tube of 70TRS3223ECDB SSOP –DB

RS23EC Reel of 2000TRS3223ECDBR Tube of 70TRS3223ECPW TSSOP –PW

RS23EC Reel of 2000TRS3223ECPWR QFN –RHL

Reel of 2000TRS3223EIRHLR PREVIEW Tube of 25TRS3223EIDW SOIC –DW

TRS3223EI Reel of 2000TRS3223EIDWR –40°C to 85°C Tube of 70TRS3223EIDB SSOP –DB

RS23EI Reel of 2000TRS3223EIDBR Tube of 70TRS3223EIPW TSSOP –PW

RS23EI Reel of 2000TRS3223EIPWR (1)

Package drawings,standard packing quantities,thermal data,symbolization,and PCB design guidelines are available at https://www.sodocs.net/doc/135529527.html,/sc/package.(2)For the most current package and ordering information,see the Package Option Addendum at the end of this document,or see the TI website at https://www.sodocs.net/doc/135529527.html, .

FUNCTION TABLES

EACH DRIVER (1)

INPUTS

OUTPUT DRIVER STATUS VALID RIN DOUT DIN

FORCEON FORCEOFF RS-232LEVEL X

X L X Z Powered off L

H H X H Normal operation with auto-powerdown disabled H

H H X L L

L H Yes H Normal operation with auto-powerdown enabled H

L H Yes L L

L H No Z Powered off by auto-powerdown feature H

L H No Z (1)H =high level,L =low level,X =irrelevant,Z =high impedance

EACH RECEIVER (1)

INPUTS

OUTPUT VALID RIN DOUT RIN

EN RS-232LEVEL L

L X H H

L X L X

H X Z Open

L No H (1)H =high level,L =low level,X =irrelevant,

Z =high impedance (off),

Open =input disconnected or connected driver off

https://www.sodocs.net/doc/135529527.html, DIN2DOUT2

RIN1

FORCEOFF

ROUT1DIN1DOUT1

RIN2

ROUT2EN

FORCEON INVALID

Absolute Maximum Ratings (1)TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION SLLS794–JUNE 2007

LOGIC DIAGRAM (POSITIVE LOGIC)

Pin numbers are for the DB,DW,and PW packages.

over operating free-air temperature range (unless otherwise noted)

MIN

MAX UNIT V CC

Supply voltage range –0.36V V+

Positive-output supply voltage range (2)–0.37V V–

Negative-output supply voltage range (2)0.3–7V V+–V–

Supply voltage difference (2)13V Driver (FORCEOFF,FORCEON,EN)–0.36V I

Input voltage range V Receiver –2525Driver

–13.213.2V O Output voltage range V Receiver (INVALID)

–0.3V CC +0.3DB package

70DW package

58θJA Package thermal impedance (3)(4)°C/W PW package

83RHL package

PREVIEW T J

Operating virtual junction temperature 150°C T stg

Storage temperature range –65150°C (1)

Stresses beyond those listed under "absolute maximum ratings"may cause permanent damage to the device.These are stress ratings only,and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions"is not implied.Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.(2)

All voltages are with respect to network GND.(3)

Maximum power dissipation is a function of T J (max),θJA ,and T A .The maximum allowable power dissipation at any allowable ambient temperature is P D =(T J (max)–T A )/θJA .Operating at the absolute maximum T J of 150°C can affect reliability.

(4)The package thermal impedance is calculated in accordance with JESD 51-7.

https://www.sodocs.net/doc/135529527.html, Recommended Operating Conditions (1)

Electrical Characteristics (1)TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION

SLLS794–JUNE 2007See Figure 6

MIN

NOM MAX UNIT V CC =3.3V 3 3.3 3.6Supply voltage

V V CC =5V 4.55 5.5V CC =3.3V 2Driver and control V IH

DIN,EN,FORCEOFF,FORCEON V high-level input voltage V CC =5V 2.4Driver and control V IL

DIN,EN,FORCEOFF,FORCEON 0.8V low-level input voltage Driver and control input voltage DIN,EN,FORCEOFF,FORCEON 0 5.5V V I

Receiver input voltage –2525V TRS3223EC 070T A

Operating free-air temperature °C TRS3223EI –4085(1)Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(see Figure 5)

PARAMETER

TEST CONDITIONS MIN TYP (2)MAX UNIT Input leakage EN,FORCEOFF,I I ±0.01±1μA current FORCEON

V CC =3.3V or 5V,T A =25°C,Auto-powerdown disabled

0.31mA No load,FORCEOFF and FORCEON at V CC I CC Supply current Powered off

No load,FORCEOFF at GND 110μA No load,FORCEOFF at V CC ,FORCEON at GND,Auto-powerdown enabled

110All RIN are open or grounded (1)

Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.

(2)All typical values are at V CC =3.3V or V CC =5V,and T A =25°C.

https://www.sodocs.net/doc/135529527.html, DRIVER SECTION

Electrical Characteristics (1)

Switching Characteristics (1)TRS3223E 3-V TO 5.5-V

MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION SLLS794–JUNE 2007over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(see Figure 5)

PARAMETER

TEST CONDITIONS MIN TYP (2)MAX UNIT V OH

High-level output voltage DOUT at R L =3k ?to GND 5 5.4V V OL

Low-level output voltage DOUT at R L =3k ?to GND –5–5.4V I IH

High-level input current V I =V CC ±0.01±1μA I IL

Low-level input current V I at GND ±0.01±1μA V CC =3.6V,V O =0V I OS

Short-circuit output current (3)±35±60mA V CC =5.5V,V O =0V r o

Output resistance V CC ,V+,and V–=0V,V O =±2V 30010M ?FORCEOFF =GND,V CC =3V to 3.6V,V O =±12V ±25I OZ

Output leakage current μA FORCEOFF =GND,V CC =4.5V to 5.5V,V O =±12V ±25(1)

Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.(2)

All typical values are at V CC =3.3V or V CC =5V,and T A =25°C.

(3)Short-circuit durations should be controlled to prevent exceeding the device absolute power dissipation ratings,and not more than one output should be shorted at a time.

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(see Figure 5)

(1)

Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.(2)

All typical values are at V CC =3.3V or V CC =5V,and T A =25°C.

(3)Pulse skew is defined as |t PLH –t PHL |of each channel of the same device.

https://www.sodocs.net/doc/135529527.html, RECEIVER SECTION

Electrical Characteristics (1)

Switching Characteristics (1)TRS3223E 3-V TO 5.5-V MULTICHANNEL

RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION

SLLS794–JUNE 2007over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)(see Figure 6)

PARAMETER

TEST CONDITIONS MIN TYP (2)MAX UNIT V OH

High-level output voltage I OH =–1mA V CC –0.6V CC –0.1V V OL

Low-level output voltage I OL =1.6mA 0.4V V CC =3.3V 1.6 2.4V IT+

Positive-going input threshold voltage V V CC =5V 1.9 2.4V CC =3.3V 0.6 1.1V IT–

Negative-going input threshold voltage V V CC =5V 0.6 1.4V hys

Input hysteresis (V IT+–V IT–)0.5V I OZ

Output leakage current EN =V CC ±0.05μA r i

Input resistance V I =±3V to ±25V 35k ?(1)

Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.

(2)All typical values are at V CC =3.3V or V CC =5V,and T A =25°C.

over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)

(1)

Test conditions are C1–C4=0.1μF at V CC =3.3V ±0.3V;C1=0.047μF,C2–C4=0.33μF at V CC =5V ±0.5V.(2)

All typical values are at V CC =3.3V or V CC =5V,and T A =25°C.

(3)Pulse skew is defined as |t PLH –t PHL |of each channel of the same device.

https://www.sodocs.net/doc/135529527.html,

AUTO-POWERDOWN SECTION Electrical Characteristics

Switching Characteristics TRS3223E

3-V TO5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER

WITH±15-kV ESD PROTECTION

SLLS794–JUNE2007

over recommended ranges of supply voltage and operating free-air temperature(unless otherwise noted)(see Figure5) PARAMETER TEST CONDITIONS MIN MAX UNIT

Receiver input threshold for

V T+(valid)FORCEON=GND,FORCEOFF=V CC 2.7V INVALID high-level output voltage

Receiver input threshold for

V T(valid)FORCEON=GND,FORCEOFF=V CC–2.7V INVALID high-level output voltage

Receiver input threshold for

V T(invalid)FORCEON=GND,FORCEOFF=V CC–0.30.3V INVALID low-level output voltage

I OH=1mA,FORCEON=GND,

V OH INVALID high-level output voltage V CC–0.6V

FORCEOFF=V CC

I OL=1.6mA,FORCEON=GND,

V OL INVALID low-level output voltage0.4V

FORCEOFF=V CC

over recommended ranges of supply voltage and operating free-air temperature(unless otherwise noted)(see Figure5)

PARAMETER TYP(1)UNIT t valid Propagation delay time,low-to high-level output1μs

t invalid Propagation delay time,high-to low-level output30μs

t en Supply enable time100μs (1)All typical values are at V CC=3.3V or V CC=5V,and T A=25°C.

https://www.sodocs.net/doc/135529527.html,

PARAMETER MEASUREMENT INFORMATION

TEST CIRCUIT

VOLTAGE WAVEFORMS ?3 V ?3 V 3 V 3 V 0 V 3 V 1.5 V 1.5 V Output Input V OL V OH t TLH

RS-232

Output

t THL L SR(tr)+6V t THL or t TLH TEST CIRCUIT VOLTAGE WAVEFORMS 0 V 3 V

Output Input V OL V OH t PLH

RS-232

Output

t PHL 50%50%1.5 V 1.5 V TEST CIRCUIT VOLTAGE WAVEFORMS 50%50%?3 V 3 V 1.5 V 1.5 V Output

Input

V OL V OH t PHL t PLH Output

EN

TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION

SLLS794–JUNE 2007A.

C L includes probe and jig capacitance.B.The pulse generator has the following characteristics:PRR =250kbit/s,Z O =50?,50%duty cycle,t r ≤10ns,

t f ≤10ns.

Figure 1.Driver Slew Rate

A.

C L includes probe and jig capacitance.B.The pulse generator has the following characteristics:PRR =250kbit/s,Z O =50?,50%duty cycle,t r ≤10ns,

t f ≤10ns.

Figure 2.Driver Pulse Skew

A.

C L includes probe and jig capacitance.B.The pulse generator has the following characteristics:Z O =50?,50%duty cycle,t r ≤10ns,t f ≤10ns.

Figure 3.Receiver Propagation Delay Times

https://www.sodocs.net/doc/135529527.html, TEST CIRCUIT

VOLTAGE WAVEFORMS

Output V OL V OH )

3 V 0 V Output Input Output

TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION SLLS794–JUNE 2007

PARAMETER MEASUREMENT INFORMATION (continued)

A.

C L includes probe and jig capacitance.B.The pulse generator has the following characteristics:Z O =50?,50%duty cycle,t r ≤10ns,t f ≤10ns.

Figure 4.Receiver Enable and Disable Times

https://www.sodocs.net/doc/135529527.html,

TEST CIRCUIT VOLTAGE WAVEFORMS

INVALID

Output

Receiver

Input

INVALID 2.7 V

2.7 V

0.3 V

0.3 V

0 V V+CC V?Supply Voltages ?Auto-powerdown disables drivers and

reduces supply current to 1 μA

EN TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION

SLLS794–JUNE 2007PARAMETER MEASUREMENT INFORMATION (continued)

A.

C L includes probe and jig capacitance.B.The pulse generator has the following characteristics:PRR =250kbit/s,Z O =50?,50%duty cycle,t r ≤10ns,

t f ≤10ns.

Figure 5.INVALID Propagation Delay Times and Supply Enabling Time

https://www.sodocs.net/doc/135529527.html, APPLICATION INFORMATION

DIN1

FORCEOFF

FORCEON DOUT1

ROUT1

C1RIN1C BYPASS

DIN2

INVALID

= 0.1m F

V CC

C1C2, C3, and C43.3 V " 0.3 V

5 V " 0.5 V

3 V to 5.5 V 0.1 μF 0.047 μF 0.1 μF 0.47 μF 0.33 μF 0.1 μF V CC vs CAPACITOR VALUES

?

C3 can be connected to V CC or GND.

NOTES: A.Resistor values shown are nominal.

B.Nonpolarized ceramic capacitors are acceptable. If polarized tantalum or electrolytic capacitors are used, they should be

connected as shown.TRS3223E 3-V TO 5.5-V MULTICHANNEL RS-232LINE DRIVER/RECEIVER WITH ±15-kV ESD PROTECTION SLLS794–JUNE 2007

Figure 6.Typical Operating Circuit and Capacitor Values

PACKAGING INFORMATION

Orderable Device Status(1)Package

Type Package

Drawing

Pins Package

Qty

Eco Plan(2)Lead/Ball Finish MSL Peak Temp(3)

TRS3223ECDB ACTIVE SSOP DB2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDBG4ACTIVE SSOP DB2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDBR ACTIVE SSOP DB202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDBRG4ACTIVE SSOP DB202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDW ACTIVE SOIC DW2025Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDWG4ACTIVE SOIC DW2025Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDWR ACTIVE SOIC DW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECDWRG4ACTIVE SOIC DW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECPW ACTIVE TSSOP PW2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECPWG4ACTIVE TSSOP PW2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECPWR ACTIVE TSSOP PW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223ECPWRG4ACTIVE TSSOP PW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDB ACTIVE SSOP DB2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDBG4ACTIVE SSOP DB2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDBR ACTIVE SSOP DB202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDBRG4ACTIVE SSOP DB202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDW ACTIVE SOIC DW2025Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDWG4ACTIVE SOIC DW2025Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDWR ACTIVE SOIC DW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIDWRG4ACTIVE SOIC DW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIPW ACTIVE TSSOP PW2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIPWG4ACTIVE TSSOP PW2070Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIPWR ACTIVE TSSOP PW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM

TRS3223EIPWRG4ACTIVE TSSOP PW202000Green(RoHS&

no Sb/Br)

CU NIPDAU Level-1-260C-UNLIM (1)The marketing status values are defined as follows:

ACTIVE:Product device recommended for new designs.

LIFEBUY:TI has announced that the device will be discontinued,and a lifetime-buy period is in effect.

NRND:Not recommended for new designs.Device is in production to support existing customers,but TI does not recommend using this part in a new design.

PREVIEW:Device has been announced but is not in production.Samples may or may not be available.

OBSOLETE:TI has discontinued the production of the device.

(2)Eco Plan-The planned eco-friendly classification:Pb-Free(RoHS),Pb-Free(RoHS Exempt),or Green(RoHS&no Sb/Br)-please check https://www.sodocs.net/doc/135529527.html,/productcontent for the latest availability information and additional product content details.

TBD:The Pb-Free/Green conversion plan has not been defined.

Pb-Free(RoHS):TI's terms"Lead-Free"or"Pb-Free"mean semiconductor products that are compatible with the current RoHS requirements for all6substances,including the requirement that lead not exceed0.1%by weight in homogeneous materials.Where designed to be soldered at high temperatures,TI Pb-Free products are suitable for use in specified lead-free processes.

Pb-Free(RoHS Exempt):This component has a RoHS exemption for either1)lead-based flip-chip solder bumps used between the die and package,or2)lead-based die adhesive used between the die and leadframe.The component is otherwise considered Pb-Free(RoHS compatible)as defined above.

Green(RoHS&no Sb/Br):TI defines"Green"to mean Pb-Free(RoHS compatible),and free of Bromine(Br)and Antimony(Sb)based flame retardants(Br or Sb do not exceed0.1%by weight in homogeneous material)

(3)MSL,Peak Temp.--The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications,and peak solder temperature.

Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided.TI bases its knowledge and belief on information provided by third parties,and makes no representation or warranty as to the accuracy of such information.Efforts are underway to better integrate information from third parties.TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.TI and TI suppliers consider certain information to be proprietary,and thus CAS numbers and other limited information may not be available for release.

In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s)at issue in this document sold by TI to Customer on an annual basis.

TAPE AND REEL INFORMATION

*All dimensions are nominal Device Package Type Package Drawing

Pins

SPQ Reel Diameter (mm)Reel Width W1(mm)A0(mm)B0(mm)K0(mm)P1(mm)W (mm)Pin1Quadrant TRS3223ECDBR SSOP

DB 202000330.016.48.27.5 2.512.016.0Q1TRS3223ECDWR SOIC

DW 202000330.024.410.813.0 2.712.024.0Q1TRS3223ECPWR TSSOP

PW 202000330.016.4 6.957.1 1.68.016.0Q1TRS3223EIDBR SSOP

DB 202000330.016.48.27.5 2.512.016.0Q1TRS3223EIDWR SOIC

DW 202000330.024.410.813.0 2.712.024.0Q1TRS3223EIPWR TSSOP PW 202000330.016.4 6.957.1 1.6

8.016.0Q1

*All dimensions are nominal

Device Package Type Package Drawing Pins SPQ Length(mm)Width(mm)Height(mm) TRS3223ECDBR SSOP DB202000346.0346.033.0 TRS3223ECDWR SOIC DW202000346.0346.041.0 TRS3223ECPWR TSSOP PW202000346.0346.033.0 TRS3223EIDBR SSOP DB202000346.0346.033.0 TRS3223EIDWR SOIC DW202000346.0346.041.0 TRS3223EIPWR TSSOP PW202000346.0346.033.0

IMPORTANT NOTICE

Texas Instruments Incorporated and its subsidiaries(TI)reserve the right to make corrections,modifications,enhancements,improvements, and other changes to its products and services at any time and to discontinue any product or service without notice.Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete.All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.

TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty.Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty.Except where mandated by government requirements,testing of all parameters of each product is not necessarily performed.

TI assumes no liability for applications assistance or customer product design.Customers are responsible for their products and applications using TI components.To minimize the risks associated with customer products and applications,customers should provide adequate design and operating safeguards.

TI does not warrant or represent that any license,either express or implied,is granted under any TI patent right,copyright,mask work right, or other TI intellectual property right relating to any combination,machine,or process in which TI products or services are https://www.sodocs.net/doc/135529527.html,rmation published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement https://www.sodocs.net/doc/135529527.html,e of such information may require a license from a third party under the patents or other intellectual property of the third party,or a license from TI under the patents or other intellectual property of TI.

Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties,conditions,limitations,and notices.Reproduction of this information with alteration is an unfair and deceptive business practice.TI is not responsible or liable for such altered https://www.sodocs.net/doc/135529527.html,rmation of third parties may be subject to additional restrictions.

Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice.TI is not responsible or liable for any such statements.

TI products are not authorized for use in safety-critical applications(such as life support)where a failure of the TI product would reasonably be expected to cause severe personal injury or death,unless officers of the parties have executed an agreement specifically governing such use.Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications,and acknowledge and agree that they are solely responsible for all legal,regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications,notwithstanding any applications-related information or support that may be provided by TI.Further,Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications.

TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or"enhanced plastic."Only products designated by TI as military-grade meet military specifications.Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk,and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS16949requirements.Buyers acknowledge and agree that,if they use any non-designated products in automotive applications,TI will not be responsible for any failure to meet such requirements.

Following are URLs where you can obtain information on other Texas Instruments products and application solutions:

Products Applications

Amplifiers Audio

Data Converters Automotive

DLP?Products Broadband

DSP Digital Control

Clocks and Timers Medical

Interface Military

Logic Optical Networking

Power Mgmt Security

Microcontrollers Telephony

RFID Video&Imaging

RF/IF and ZigBee?Solutions Wireless

Mailing Address:Texas Instruments,Post Office Box655303,Dallas,Texas75265

Copyright?2009,Texas Instruments Incorporated