WA653SN Installation Pocket Guide & 快速安装指南(V100R003C02_05)
2240
Unit: mm 单位：mm
3
4WA653SN dimensions
WA653SN 尺寸
安装工具
安装附件
Packing List 装箱单
Verify the contents of the packing box, as shown in the following table, to ensure that you have received all necessary items. For any missing or inconsistent item, contact the supplier.打开产品包装后，请检查下表中的物品。如与实际不符，请与供应商联系。
Device Overview 设备简介
SN Item 名称
Item 名称
Description
说明
2.4G antenna port Connected to radio cable.Ports and LEDs 接口和指示灯介绍
Ground point 设备的接地点
56
24
Screw 钻孔螺钉
Expansion bolt 膨胀胶塞
7
Hexagonal bolt (M6*12)六角螺栓(M6*12)
Steel hoop 钢夹
Flat washer (M6)平垫圈（M6）Spring washer (M6)弹簧垫（M6）Flexible support
动态支架Fixed support
静态支架
Phillips screwdriver 十字螺丝刀
Flat-head screwdriver 一字螺丝刀Maker
记号笔 6 mm drill bit
6mm 钻头
Hammer drill
电钻
COAX crimping
tool 压线钳
Diagonal pliers
斜口钳
RJ45 crimping tool 网线钳Network cable
tester 网线测试仪
Claw hammer 羊角锤
Adjustable wrench 活动扳手
a
Assemble a spring washer and then a flat washer onto a hexagonal bolt. 在六角螺栓上先放置一个弹簧垫圈，再放置一个平垫圈。
b
Screw the assembly bolt tightly using the adjustable wrench to install the WA653SN onto the fixed support. 将组合好的螺栓插入安装孔，并用扳手按图示方向固定。
Installing the Flexible Support onto the WA653SN 安装动态支架
2
Installing the WA653SN onto the Fixed Support 将安装了动态支架的WA653SN 安装到静态支架上
3
a
Collecting the MAC Address of the WA653SN 采集MAC 地址
2
2
1
1在柱子上安装
1
2
2
1
3
Mistake-proofing design 防呆设计
Connecting the Cables 连接线缆
Installing the WA653SN Against a Wall 在墙面上安装
Install the fixed support against a wall.将静态支架安装到墙上。
1Installing the WA653SN 安装WA653SN
2
The procedure for installing a flexible support onto the WA653SN is the same as the procedure for installing a flexible support onto a fixed support.
在WA653SN 上安装动态支架和将动态支架安装到静态支架上的方法与在柱子上安装的步骤相同。
接地线
Shielded Network
cable Surge protection
2
1
3
4
2
Specification
说明
to +60 ℃Operating humidity
Item 分类Specification
说明Weight 重量
3.5 kg
Copyright ? Huawei Technologies Co., Ltd. All rights reserved.华为专有和保密信息 版权所有?华为技术有限公司2011。
Physical Specifications 物理规格
Connecting the Cables d
e a b
c
a
b c
d
Install a surge protection device. Keep the ground point of the surge protection device inside to facilitate ground cable connection.
安装防雷器，防雷器的接地端朝向设备内侧，目的是连接防雷器的接地线比较方便。Connect the radio cable.安装射频电缆。
Connect the radio cable
连接射频电缆
Connect the fiber
b
c
d
e
f
Install an optical module as shown in step a before connecting the fiber.
连接光纤时需要先安装光模块，如步骤a 所示。
NOTE
f
Use waterproof adhesive tape to wrap the two connectors of each surge protection device. The upper layer of the tape should overlap 1/2 of the lower layer.
Surge protection
device 防雷器
Radio cable 射频电缆
Waterproof adhesive tape 防水胶带
The ground cable to the surge
protection device 防雷器的接地线