电子行业专业英语词汇
电子行业专业英语词汇 Document number：WTWYT-WYWY-BTGTT-YTTYU-2018GT
专用词汇表
一、生产流程 1.
插机(刮蓝胶)component- inserting
2. 装配 assembly
3. 修理repair
4. 包装 packaging
5. 成品仓 finished goods warehouse
6. 返工 rework
7. 啤胶件
8. 组件成型 component moulding
9. IC 烧录 IC program 10. 插件 insection 11. 注塑 plastic injection 12. 发料 material delivery 13. 插机
14. 零件加工 component-processing 15. 炉前外观检查 visual inspection
before wave soldering
16. 电源板波峰焊 power board wave
soldering
17. 执锡
18. 零件后焊 hand soldering 19. 零件焊接&打黄胶
20. 低电压测试 low voltage test 21. 半成品外观检查Semi-finished
goods visual inspection
22. 过水洗机 23. 打热熔胶 dotting hot glue 24. 装卡板
25. pallet 栈板 26. IC 烧录 IC program 27. SMT(刮锡膏)
28. 喷油 spray conformal coating 29. 焗干防水油 30. welding 焊接 31. breathing 排气 32. feed 供料 33. Tiana 天那水
34.to load material上料 to unload
material卸料 to return
material/stock to退料
35.to fix a die装模 to take apart a
die拆模
36.cold forging 冷锻 press forging 冲
锻
37.to impose lines压线
38.to compress, compressing压缩
39.焗炉温度
40.开槽groove
41.shearing剪断
42.接线端子 terminal
43.to stake, staking, reviting铆合
44.fuse together熔合
45.electrical sparkle电火花
46.fit together组装在一起
47.fasten锁紧(螺丝)
48.rotating speed, revolution转速49.argon welding氩焊
50.to take apart a die卸下
51.to load a die装上
52.to tight a bolt拧紧螺栓 to looser
a bolt拧松螺栓
https://www.sodocs.net/doc/2011174860.html,pound die复合模
54.punched hole冲孔
55.buffing 抛光
56.chamfering machine 倒角机
57.panel board镶块
58.to cutedges=side cut=side scrap
切边
59.to pull, to stretch拉伸
60. Line streching, line pulling线拉伸
61.engraving, to engrave刻印
62.degrease脱脂
63.rinse水洗
64.pierce die冲孔模
65.forming die成型模
66.progressive die连续模
67.gang dies复合模
68.shearing die剪边模
69.riveting die铆合模
70.pierce冲孔
71.forming成型(抽凸,冲凸)
72. draw hole抽孔
73.吹热缩管
74.胶芯plastic core
二、夹具设备、工具
75.烙铁 iron
76.排气扇 A exhaust fan
77.稀释剂 a tinner
78.水洗锡线
79.pallet栈板
80.gunk 料斗
81.caliper gauge 卡规
82.Screw driver起子
83.barcode scanner条码扫描器
84.热风枪 hot air reflowing gun 85.taker取料机
86.roller 滚筒 runner 流道
87.plastic basket胶筐
88.isolating plate baffle plate;
barricade隔板
89.steel plate钢板
90.roll material卷料
91.conveyer belt输送带
92.transmission rack输送架
93.钢网 stencil
94.油墨 printing ink
95.插机并过炉
96.高压测试 hi-pot test
97.铣刀 milling cutter
98.发热管 heater
99.烙铁咀 iron tip
100.静电手套 ESD gloves 101.风枪 air gun
102.p unch冲头
103.g roove punch压线冲子
104.a ir vent排气道
105.w elding line熔合痕
106.C ONN Connector 连接器107.C AV Cavity 模穴
108.A SS'Y Assembly 装配,组装109.继电器relay
110.磨床切割片
111.延时器 delay timer
112.热电偶Heat control sensor 、thermocouple
113.电磁阀Solenoid
114.温控器Temperature control 115.烙铁发热芯heater core for iron 116.剪钳 wire cutter
117.电批开关Electric screw driver switch
118.电批Electric screw driver 119.电批齿轮Electric screw driver gear 120.火牛transformer
121.碳刷Carbon brush
122.吸锡泵suck solder pump
123.尖嘴钳micro long nose pliers 124.热熔胶枪glue gun
125.热风筒heating gun
126.f use machine热熔机
127.烙铁座iron seat
128.静电带wrist strap
129.波峰锡炉wave soldering oven 130.水循环系统water-recycling
system
131.水洗机
132.防水油 conformal coating
133.自动成型机 auto-moulding machine 134.电晶体自动成型机
135.螺丝泵 screw pump
136.恒温运风焗炉
137.手浸锡炉
138.剪脚机
139.超声波蒸水机
140.表面组件拾放机
141.高周波塑料熔接机
142.半自动锡浆印刷机
143.剪线机
144.超声波啤机ultrasonic welding machine
145.自动绕线机
146.超声波清洗机 ultrasonic cleaning machine
147.振动试验台vibration test
platform
148.计算机剥线机electronic wire-peeling machine
149.贴片机 SMT equipment
150.供料器 feeder
151.红外焗炉
152.封黑胶预热炉
153.回焊炉温度曲线测试仪
154.焗炉155.进料器车
156.锡浆搅拌机
157.无铅波峰焊机
158.开线机
159.封口机
160.胶纸机
161.移载装置
162.送板机
163.周转车
164.发电机electric generator 165.注塑机 plastic injection machine 166.碎料机smashing machine 167.干燥机drier
168.自动吸料机auto-sucking machine 169.锯床
170.车床lathe
171.钻床
172. punching machine 冲床
173.干燥机 drier
174.冷水机 cooler
175.数控精密火花机
176.移印机 printer
177.手动吊机
178.热油机oil-heating machine 179.叉车forklift
180.磨床grinder
181.铣床miller
182. sheet metal parts 冲件
183. punching machine 冲床
184.过滤器 filter
185.碎料干燥机
186.抽湿机
187.热风回焊炉 hot air reflow
soldering oven
188.注塑机plastic injeciton machine 189.润滑油grease
190.汽缸Rmulti cylinder
191.螺丝screw 192.弹簧spring
193.蜂鸣器buzzle
194.刮刀 squeegee
195.真空杯vacuum cup
196.真空咀vacuum tip
197.喷嘴Nozzle
198.支架bracket
199.六角板手
200.过滤器Filter
201.密封圈 airproof ring 202.套筒/活塞piston
203.顶针thimble
204.传输皮带belt/conveyor 205.真空棉?pad vacuum 206.消音器muffler
207.滑轮Pulley,idler tension,asy pre-tension
208.夹片Replacement Fine Foil 209.线夹wire clamp
210.扎线 tie wrap
211.通风孔 blowhole
212.自功螺丝 self-tapping screw 213.保险丝Fuse
214.高度规High dividers
215.螺线管solenoid
216.送/扯线螺线管Spring solenoid assembly
217.焊咀gaiser
218.电源线Power cord
219.测试针test probe
220.变压器transformer
221.弹性定位柱spring fixation pole 222.铝皮sheet aluminum 223.网络线communicate wire 224.电磁阀Solenoid AIRTAC 225.精调电阻Precision adjustable resisto
226.脚踏开关foot switch
227.开关电源switching power 228.散热片Thermal Conductive Pad 229.旋转开关Rotary switch 230.接线柱Pole Wiring
231.音频插头Audio plug
232.按键开关keyswitch
233.保险丝座Fuse jack
234.定位柱fixation pole
235.ICT压棒ICT-PRESSING
STICK
236.除泡剂Defoamer
237.继电器Relay
238.电线束electrical wiring harness 239.锡箔纸Solder foil papper 240.针筒needle canister
241.光电开关Photoelectricity switch 242.电批Electric screw driver 243.烙铁soldering iron
244.黄油（润滑油）butter
(lubricant)
245.气管wind pipe
246.刀片blade
247.bolt螺栓
248.trailer=long vehicle拖板车249.stopper阻挡器
250.flow board流水板
251.v accum cleaner吸尘器
252.quenching淬火
253.tempering回火
254. annealing退火
255.volatile挥发性
256.风批Pneumatic driver
257.电批Electric screw driver
三、质量管理
QC : quality control 质量管理258. IQC : incoming quality control 进料质量管理
259..OQC : output quality control 出货质量管理
260.PQC : process quality control 制程质量管理也称
261.I PQC: in process quality control. 262.AQL : acceptable quality level 允收标准
263.CQA: customer quality
assurance 客户质量保证
264.PPM Parts Per Million 百万分之一
265.MA : major defect 主要缺点MI : minor defect 次要缺点266.CR :critical defect 关键缺点267.SMT : surface mounting
technology 表面粘贴技术
268.SMD : surface mounting device 贴片机
269.SMC : surface mounting
component 表面粘贴组件
270.ECN : engineering change notice 工程变更通知
271.D CN : design change notice 设计变更通知
272.BOM : bill of material 物料清单
https://www.sodocs.net/doc/2011174860.html,-STD-105E : 美国陆军标准,也称单次抽样计划.
274. NG :Not Good 不行,不合格275.ESD Electry-static Discharge 静电排放
276.5S 希腊语整理,整顿,清扫,清洁,教养
277.Polarity : 电性/极性 Icicles : 锡尖
278.Non-wetting : 空焊
279.burr 毛刺，批锋
280.locking knot 死结
281.t orsion 扭曲
282.warpage 翘曲
283.waviness 波痕
284. flying 飞件
285.blister 起泡
286.Short circuit : 短路
287.冷焊 cold soldering
288.non-welding 289.假焊
290.包焊
291.焊点
292.lifted solder 浮焊
293.pseudo soldering 虚焊
294. open soldering脱焊
295.Splay mark?水纹
296.icicle/solder projection拉尖297.Flow mark?流纹
298.White patches on surface?表面白斑
299.Sink marks?缩影
300.Mold release?脱模
301.焊盘 soldering tray 302.Missing component : 缺件303.Wrong component : 错件304. Excess component : 多件305.Insufficient solder : 锡少306.Excessive solder : 锡多
307.Solder residue : 锡渣
308.Solder ball : 锡球
309.Tombstone : 墓碑
310.b reaking.(be)broken,(be)cracked 断裂
311.Sideward : 侧立
312.c osmetic defect外观不良313. mixed color杂色
314. die repair模修
315. rust生锈
316. grease/oil stains油污
317. delamination起鳞
318. gouge沟槽;凿槽
319. inclusion杂质
320. poor staking铆合不良321. oxidation 氧化
322. abrasion磨损
323.reverse angle = chamfer倒角324. failure, trouble故障325.dents压痕
326.defective upsiding down抽芽不良
327.defective to staking铆合不良328.embedded lump镶块
329.feeding is not in place送料不到位
330.stamping-missing漏冲
331.e xcessive gap间隙过大
332.burr(金属)flash(塑件)毛边https://www.sodocs.net/doc/2011174860.html,dewed=moldy=mouldy发霉334. slipped screw head & slippery screw head螺丝滑头
335.slipped screwhead/shippery screw thread滑手
336.speckle斑点
337.dimension/size is a little bigger 尺寸偏大(小)
338.not up to standard不合规格 out of specification
339.shrinking/shrinkage缩水
340.mixed color杂色
341.d iscoloration异色
342.ageing 老化
343.hardening 硬化
344. overheating 过热
345.rust prevention 防蚀
346.tempering 回火
347.water spots水渍
348.exposed metal/bare metal金属裸露
https://www.sodocs.net/doc/2011174860.html,ck of painting烤漆不到位https://www.sodocs.net/doc/2011174860.html,ponent damage : 零件破损351.G old finger : 金手指
352.SOP : standard operation
process 标准操作流程
353.SIP : standard inspection
process 标准检验流程
354. Simple random sampling : 简单随机抽样
355.SPC : Statistical process
control 356.SQE : Supplier quality
engineering
357.Sampling sample :抽样计划358.fixture : 治具
359.Gauge 量规
360.QTS: Quality tracking system 质量追查系统
361.S pare parts :备用品
362.Inventory report for : 库存表363.Manpower/Tact estimation 工时预算
364. Calibration : 校验
365.Corrugated pad : 波纹垫366.Conductive bag : 保护袋367.Fixture : 制具
368.Probe : 探针
369.Lint-free gloves : 静电手套370.Wrist wrap : 静电手环
371.p lug hole孔塞
372.Wrong direction 极性反
https://www.sodocs.net/doc/2011174860.html,ponent damage or broken 零件破损
374. Unmeleted solder熔锡不良375.flux residue松香残渣
376.wrong label or upside down label 贴反
377.mixed parts机种混装
378.poor solder mask绿漆不良379.氧化 Oxidization
380.刮花 Scratch
381.脏污Contamination
382.变形 Deformation 383.stand off height浮高
384. IC reverse IC反向
385. supervisor课长
386.Forman组长
387.PPM: Parts per million 不良率388.DPU: Defects per unit 单位不良率
389.Resistor: 电阻390.Capacitor:电容
391.R esistor array : 排阻
392.Capacitor array: 排容
393. DIODE: 二极管
394.triode: 三极管
395.Crystal:震荡器
396.Fuse:保险丝
397.Bead: 电感 inductor 398.Connector:连结器
399.Metal Shearing:裁剪
400.ERP: Enterprise Resource Planning 企业资源规划
401.P rocessed material: 流程性材料402.Corrective action:纠正措施403. Preventive action:预防措施404.PDCA:Plan/Do/Check/Action计划/实施/检查/处理
405.Oscillator:振荡器
406.Adapter: 适配器
407.Spindle:轴心
408.WIP: Work in process半成品Waive:特别采用
409.FMEA:Protentical Failure Mode and Effects Analysis失效模式与效
应分析
410.M SA: Measurement Systems
Analysis 量测系统分析
411.Benchmarking:竞争标竿
412. Roka Yoke 防错法
413. Mistake Proofing 防呆法
414. Fool-Proof System防呆系统415. Specified Requirement:规定要求416. AOQ: Average Outgoing Quality 平均检出质量 AOQL: Average
Outgoing Quality Limit 平均检出
质量界限
417. Benchmarking 基准点
418. Calibration 校准419. Continuous improvement 持续改进
420. Deviation / Substitution 偏差/ 置换
421.ESD: Electrostatic discharge 静电释放
422.FMEA: Failure Mode Effect Analysis 失误模式效应分析423. First Article approval 产品的首次论证
424.First pass yield 一次性通过的成品率
425.First sample inspection 第一次样品检验
426.FMECA: Failure mode effect and critically analysis 失误模式,效
应及后果分析
427.Life Testing 寿命试验
Lot traceability 批量可追溯性428.NONCONFORMANCE 不符合
429.OUT-OF-CONTROL PROCESS 失控工序
430.Pilot Application 试产(试用) 431.P PM: Parts per million 百万分之一432.Process capability index 工序能力指数
433. Total quality management 全面质量管理
434.Site Audit 现场审核
435.Failure rate percentage 失误百分率
436.Customer complaints 客户投诉437.Root cause analysis of failures 失误根原分析
https://www.sodocs.net/doc/2011174860.html,yout Inspection:全尺寸检验439.Bulk material:散装材料
440.Feasibility Reviews:可行性审查441.P re-launch:量产前
442.Stock rotation :存货周转443. Inventory levels:最低库存量444.Interim action:临时措施445.Permanent action:永久措施446.vibration test振动试验447.Conveyer流水线物料板448.fasten锁紧(螺丝) 449.fuse machine热熔机450.SOP制造作业程序451.w ork cell工作间
452.trolley台车
453. carton纸箱
454.电阻 Resistor
455.电容 Capacitor
456.晶振 Crystal resonator 457.开关 Switch
458.插座 Jack
459.插头 Plug
460.工艺 Workmanship 461.喷油 Conformal coating 462.插件Insertion
481.C TQ=critical to quality 463.回焊炉 Reflowing oven
464.飞达 feeder
465.吸嘴
466.钢网 Stencil
467.抛料
468.线股Strand
469.松香 Flux
470.尾数 WP
471.锡炉 DIP
472.暂置 Hold
473.全检 Sorting
474.条形码 Bar code
475.日期编码 Date code
476.标准作业指导书 SOP Standard
operation plan
477.过电压保护 OVP Over voltage
protect
478.汶波/噪声Noise
479.连接器Connector
480.线材 Cable