UNISONIC TECHNOLOGIES CO., LTD
L1119 CMOS IC
1.5A LOW DROPOUT REGULATORS
DESCRIPTION
The UTC L1119 is a fast ultra low-dropout linear regulator that developed in CMOS process which allows low quiescent current operation independent of output load current. This CMOS process also allows the device to operate under extremely low dropout conditions.
The UTC L1119 allows to operate from a 2.5V~7.0V input supply. Wide range of preset output voltage options are available and respond very fast to step changes in load which makes them suitable for low voltage microprocessor applications.
FEATURES
* Low ground current
* Load regulation of 0.04%
* Output current of 1.5A DC is guaranteed * Accurate output voltage.(± 1.5%)
* Extremely low output capacitor requirements * Over temperature/ Over current protection
*Pb-free plating product number: L1119L-xx
ORDERING INFORMATION
Order Number Pin Assignment
Normal Lead Free Plating Package 1 2 3
Packing
L1119-xx-AA3-A-R L1119L-xx-AA3-A-R SOT-223 G O I Tape Reel L1119-xx-AA3-C-R L1119L-xx-AA3-C-R SOT-223 G I O Tape Reel L1119-xx-AB3-A-R L1119L-xx-AB3-A-R SOT-89 G O I Tape Reel L1119-xx-AB3-B-R L1119L-xx-AB3-B-R SOT-89 O G I Tape Reel L1119-xx-AB3-C-R L1119L-xx-AB3-C-R SOT-89 G I O Tape Reel L1119-xx-AB3-D-R L1119L-xx-AB3-D-R SOT-89 I G O Tape Reel L1119-xx-TN3-D-R L1119L-xx-TN3-D-R TO-252 I G O Tape Reel L1119-xx-TN3-D-T L1119L-xx-TN3-D-T TO-252 I G O Tube
MARKING INFORMATION
BLOCK DIAGRAM
GND
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL RATINGS
UNIT Input Supply Voltage V IN-0.3 ~ +7.5 V
Output Voltage V OUT-0.3 ~ +7.5 V
Output Current I OUT Short Circuit Protected
Power Dissipation P D Internally
Limited
Operating Junction Temperature T OPR-40 ~ +125
Storage Temperature T STG-65 ~ +150
Note Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
RECOMMENDED OPERATING RATINGS
PARAMETER SYMBOL RATINGS
UNIT Input Supply Voltage V IN 2.5 ~ 7.0 V
Maximum Operating Current (DC) I OPR(MAX) 1.5 A Operating Junction Temperature T J-40 ~ +125
Note: Absolute maximum ratings are those values beyond which the device could be permanently damaged.
Absolute maximum ratings are stress ratings only and functional device operation is not implied.
ELECTRICAL CHARACTERISTICS
(T J=25°C, V IN =V OUT+1V, I L=10mA, C OUT=33μF,unless otherwise specified.)
PARAMETER SYMBOL TEST
CONDITIONS
MIN
TYP
MAX UNIT
I L = 150 mA 38 45
Dropout Voltage (Note) V D
I L = 1.5 A 870
mV
Peak Output Current I PEAK 2.0 2.5 A
I L = 150 mA 4 9
Ground Pin Current I GND
I L = 1.5 A 5 14
mA
Output Voltage Tolerance V OUT 10 mA ≤ I L≤ 1.5A
V OUT +1 ≤ V IN≤ 7.0V
-1.5 0 +1.5 %
Line Regulation ?V OUT V OUT+1V Short Circuit Current I SC 4.5 A AC PARAMETERS Output Noise Density ρN(l/f) f = 120Hz 0.8 μV BW = 10Hz – 100kHz 150 Output Noise Voltage eN BW = 300Hz – 300kHz 100 μV(rms) V IN = V OUT + 1.5V C OUT =100uF, V OUT = 3.3V 60 Ripple Rejection RR V IN = V OUT + 0.3V C OUT =100uF, V OUT = 3.3V 40 dB OVER TEMPERATURE PROTECTION Shutdown Threshold T SHDN165 °C Thermal Shutdown Hysteresis T HYS 10 °C Note: Dropout voltage is defined as the minimum input to output differential voltage at which the output drops 2% below the nominal value. Dropout voltage specification applies only to output voltages of 2.5V and above. For output voltages below 2.5V, the drop-out voltage is nothing but the input to output differential, since the minimum input voltage is 2.5V. TYPICAL CHARACTERISTICS (V IN =V OUT +1V, V OUT =2.5V, C OUT =33μF, I OUT =10mA, C IN =68μF, T a =25°C.) -40-20 020406080100120140 0.05 0.1 0.15 0.2 0.25 Temperature (℃)D r o p -O u t (V ) Drop-Out Voltage vs Temperature (I L ) -40-20 020406080100120 140 0.15 0.175 0.2 0.225 Temperature (℃) D r o p -O u t (V ) Drop-Out Voltage vs Temperature (V OUT ) 0.125 V OUT vs Temperature 0.00D e l t a V O U T (%) -0.10-0.20 -0.30-0.40-0.50-0.60-0.70-0.80-0.90 -75 -50 -25 25 50 75 100125 Temperature (℃)10 0.010 10Frequency (Hz) N o i s e ( V / H z ) Noise Density 1.000 0.100 100 1000 100000 10000 03V IN (V) V O U T (V ) Input Voltage vs Output Voltage 2.50.51.52 1 1 23 4 TYPICAL CHARACTERISTICS(Cont.) 100 Frequency (Hz) Output Noise Density 1000 10000 100000 100 Output Noise Density 1000 10000 100000 Frequency (Hz) 10 -10 90 Frequency (Hz) Ripple Rejection vs Frequency 1M 100K 10K 1K 100 10203040506070 80 R i p p l e R e j e c t i o n (d B ) Load Transient Response 20 I O U T (A ) V O U T (V ) Line Transient Response 10 s/DIV V I N (V ) V O U T (V ) Line Transient Response 10 s/DIV V I N (V ) V O U T (V ) TYPICAL CHARACTERISTICS(Cont.) Line Transient Response 10 s/DIV V I N (V ) V O U T (V ) Line Transient Response 10 3.25 3.33.35V I N (V ) V O U T (V ) 5.34.3 3.453.4