ansys瞬态分析例子

/BATCH
/COM,ANSYS RELEASE 12.1 UP20091102 10:30:00 10/26/2011
/COM,ANSYS RELEASE 12.1 UP20091102 10:00:45 10/26/2011
/prep7,start
/prep7
*SET,width,1000
*SET,length,2000
*SET,high,1000
*SET,t,20
*SET,b,15
*SET,i,(b**4)/12
et,1,63
et,2,4
r,1,t,
r,2,b*b,i,i,b,b
mp,ex,1,2.1e5
mp,nuxy,1,0.3
mp,dens,1,7.9e-9
rect,,length,,,width
rectng,,length,,width
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/USER, 1
/VIEW, 1, 0.865338004228 , 0.451428339699 , 0.217721364489
/ANG, 1, 22.4514579849
/REPLO
/VIEW, 1, -0.730890064214 , -0.279857574373 , 0.622478475210
/ANG, 1, 1.61686369195
/REPLO
/VIEW, 1, -0.153639345279 , 0.385325691642E-01, 0.987375406163
/ANG, 1, -5.00264216419
/REPLO
k,5,,,-high
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/DIST,1,1.08222638492,1
/REP,FAST
/VIEW, 1, -0.201237952025 , -0.287752130587 , 0.936323660925
/ANG, 1, -4.36898136787
/REPLO
/VIEW, 1, -0.235675626511 , -0.703009733097 , 0.670995018043
/ANG, 1, -0.772958995386
/REPLO
k,6,length,,-high
k,7,length,width,-high
k,8,,width,-high
l,1,5
l,2,6
l,3,7
l,4,8
lplot,all
esize,100
amesh,all
type,2
real,2
lmesh,5,8
*dim,pressure,table,4,1,1
*set,pressure(0,1,1),0
*set,pressure(1,0,1),0
*set,pressure(2,0,1),1
*set,pressure(2,1,1),0.01
*set,pressure(3,0,1),2
*set,pressure(3,1,1),0.01
*set,pressure(4,0,1),6
*set,pressure(4,1,1),0
finish
/solu
antype,trans
trnopt,full
ksel,s,loc,z,-high
dk,all,all
outres,all,1
alphad,5
sfa,1,,pres,%pressure%
deltim,0.2,0.05,0.5
autots,on
kbc,0
time,4.0
solve
finish
! /post
/post1
FINISH
/POST26
nsol,2,146,u,z
/grid,1
plva,2
/DIST,1,0.924021086472,1
/REP,FAST
finish
SAVE

开始的时候说过，其中有一些命令我不是很清楚，就是指下面这几条
*dim,pressure,table,4,1,1
*set,pressure(0,1,1),0
*set,pressure(1,0,1),0
*set,pressure(2,0,1),1
*set,pressure(2,1,1),0.01
*set,pressure(3,0,1),2
*set,pressure(3,1,1),0.01
*set,pressure(4,0,1),6
*set,pressure(4,1,1),0