机械与工厂英语
组装、冲压、喷漆等专业词汇
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
Screw driver起子
Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌
OOBA开箱检查
fit together组装在一起
fasten锁紧(螺丝)
fixture 夹具(治具)
pallet栈板
barcode条形码
barcode scanner条形码扫描仪fuse together熔合
fuse machine热熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
cosmetic inspect外观检查
inner parts inspect内部检查thumb screw大头螺丝
lbs.inch镑、英寸
EMI gasket导电条
front plate前板
rear plate后板
chassis |'∫?si| 基座bezel panel面板
power button电源按键
reset button重置键
Hi-pot test of SPS高源高压测试V oltage switch of SPS
电源电压接柆键
sheet metal parts 冲件
plastic parts塑料件
SOP制造作业程序
material check list物料检查表work cell工作间
trolley台车
carton纸箱
sub-line支线
left fork叉车
personnel resource department 人力资源部
production department生产部门planning department企划部
QC Section品管科
stamping factory冲压厂painting factory烤漆厂molding factory成型厂common equipment常用设备uncoiler and straightener整平机punching machine 冲床
robot机械手
hydraulic machine油压机
lathe车床
planer |'plein |刨床
miller铣床
grinder磨床
driller钻床
linear cutting线切割
electrical sparkle电火花
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager |'depjuti| =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to file burr 锉毛刺
final inspection终检
to connect material接料
to reverse material 翻料
wet station沾湿台
Tiana天那水
cleaning cloth抹布
to load material上料
to unload material卸料
to return material/stock to退料
scraped |'skr?pid|报废
scrape ..v.刮;削
deficient purchase来料不良
manufacture procedure制程
deficient manufacturing procedure制程不良oxidation |' ksi'dei n|氧化
scratch刮伤
dents压痕defective upsiding down抽芽不良defective to staking铆合不良embeded lump|in'bed| |l mp|镶块feeding is not in place送料不到位stamping-missing漏冲
production capacity生产力
education and training教育与训练proposal improvement提案改善
spare parts=buffer备件
forklift叉车
trailer=long vehicle拖板车
compound die合模
die locker锁模器
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称administration/general affairs dept总务部automatic screwdriver电动启子thickness gauge厚薄规
gauge(or jig)治具
power wire电源线
buzzle蜂鸣器
defective product label不良标签identifying sheet list标示单screwdriver holder起子插座
pedal踩踏板
stopper阻挡器
flow board流水板
hydraulic handjack油压板车
forklift叉车
pallet栈板
glove(s)手套
glove(s) with exposed fingers割手套thumb大拇指
forefinger食指
midfinger中指
ring finger无名指
little finger小指
band-aid创可贴
iudustrial alcohol工业酒精
alcohol container沾湿台
head of screwdriver起子头
sweeper扫把
mop拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain链条
jack升降机
production line流水线
chain链条槽
magnetizer加磁器
lamp holder灯架
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
wrong part错件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良
slipped screwhead/slippery screw head螺丝滑头slipped screwhead/shippery screw thread滑手speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
poor staking铆合不良
excesssive gap间隙过大
grease/oil stains油污
inclusion杂质
painting peel off脏污
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
poor processing 制程不良
poor incoming part事件不良
fold of pakaging belt打包带折皱
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理
exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
die repair模修
enterprise plan = enterprise expansion projects企划QC品管
die worker模工
production, to produce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
culture教养
qualified products, up-to-grade products良品defective products, not up-to-grade products不良品waste废料
board看板
feeder送料机
sliding rack滑料架
defective product box不良品箱
die change 换模
to fix a die装模
to take apart a die拆模
to repair a die修模
packing material包材
basket蝴蝶竺
plastic basket胶筐
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material, to input落料to impose lines压线
to compress, compressing压缩
character die字模
to feed, feeding送料
transportation运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
feature change 特性变更
evaluation评估
prepare for, make preparations for 准备parameters参数
rotating speed, revolution转速
manufacture management制造管理abnormal handling异常处理
production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
manufacture procedure制程
operation procedure作业流程
to revise, modify修订
to switch over to, switch---to throw--over switching over 切换
engineering, project difficulty工程瓶颈
stage die工程模
automation自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
shut die架模
shut height of a die架模高度
analog-mode device类模器
die lifter举模器
argon welding氩焊
vocabulary for stamping
冲压常词汇
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
top stop上死点
bottom stop下死点
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块
reset复位
smoothly顺利
dent压痕
scratch刮伤
deformation变形
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核
processing, to process加工
delivery, to deliver 交货
to return delivery to. to send delivery back to return of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单
consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
to move away a die plate移走模板
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
common vocabulary for die engineering模具工程常用词汇
die 模具
figure file, chart file图档
cutting die, blanking die冲裁模
progressive die, follow (-on)die
连续模
compound die复合模
punched hole冲孔
panel board镶块
to cut edges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line stretching, line pulling线拉伸
engraving, to engrave刻印
up siding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
upper die base上模座
lower die base下模座
upper supporting blank上承板
upper padding plate blank上垫板
spare dies模具备品
spring 弹簧
bolt螺栓
document folder活页夹
file folder资料夹
to put file in order整理资料
spare tools location手工备品仓
first count初盘人
first check初盘复棹人
second count 复盘人
second check复盘复核人
equipment设备
waste materials废料
work in progress product在制品
casing = containerization装箱
quantity of physical inventory second count 复盘点数量
quantity of customs count
会计师盘,点数量
the first page第一联
filed by accounting department for reference会计部存查end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department)
本表请与盘点清册一起送会计部-(NHK厂区送财会部)
Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用-状况明细表
blank and waste sheet NO.
空白与作废单号
plate电镀
mold成型
material for engineering mold testing工程试模材料not included in physical inventory不列入盘点sample样品
incoming material to be inspected进货待验description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办PCE assembly production schedule sheet
PCE组装厂生产排配表
model机钟
work order工令
revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
stock age analysis sheet
库存货龄分析表
on-hand inventory现有库存
available material良品可使用
obsolete material良品已呆滞
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
year-end physical inventory difference analysis sheet
年终盘点差异分析表
physical inventory盘点数量
physical count quantity账面数量
difference quantity差异量
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts 良品
defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
on way location在途仓
oversea location海外仓
spare parts physical inventory list备品盘点清单
spare molds location模具备品仓
skid/pallet栈板
tox machine自铆机wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
pilot导正筒
trim剪外边
pierce剪内边
drag form压锻差
pocket for the punch head挂钩槽slug hole废料孔
feature die公母模
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
set screw止付螺丝
form block折刀
stop pin定位销
round pierce punch=die button圆冲子shape punch=die insert异形子
stock locater block定位块
under cut=scrap chopper清角
active plate活动板
baffle plate挡块
cover plate盖板
male die公模
female die母模
groove punch压线冲子
air-cushion eject-rod气垫顶杆spring-box eject-plate弹簧箱顶板bushing block衬套
insert 入块
club car高尔夫球车
capability能力
parameter参数
factor系数
phosphate皮膜化成
viscosity涂料粘度
alkali dipping脱脂
main manifold主集流脉
bezel斜视规
blanking穿落模
dejecting顶固模demagnetization去磁;消磁
high-speed transmission高速传递heat dissipation热传
rack上料
degrease脱脂
rinse水洗
alkaline etch龄咬
desmut剥黑膜
D.I. rinse纯水次
Chromate铬酸处理
Anodize阳性处理
seal封孔
revision版次
part number/P/N料号
good products良品
scraped products报放心品defective products不良品finished products成品disposed products处理品barcode条形码
flow chart流程窗体
assembly组装
stamping冲压
molding成型
spare parts=buffer备品coordinate坐标dismantle the die折模
auxiliary fuction辅助功能
poly-line多义线
heater band 加热片thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
edge finder巡边器
concave凸
convex凹
short射料不足
nick缺口
speck瑕疪
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
witness line证示线
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂bracket小磁导
liaison联络单
volatile挥发性
resistance电阻
ion离子
titrator滴定仪
beacon警示灯
coolant冷却液
crusher破碎机模具工程类
plain die简易模
pierce die冲孔模
forming die成型模progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸) draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边punch riveting冲压铆合side stretch侧冲压平
reel stretch卷圆压平groove压线
blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印tick-mark farside反面压印冲压名称类
extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格
die height range适用模高
die height闭模高度
burr毛边
gap间隙
weight重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
eq-height sleeves=spool等高套筒pin销
lifter guide pin浮升导料销guide pin导正销
wire spring圆线弹簧
outer guiding post外导柱
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch set上模座
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板)
stripping plate内外打(脱料板)
outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件)
deburring punch压毛边冲子
groove punch压线冲子
stamped punch字模冲子
round punch圆冲子
special shape punch异形冲子
bending block折刀
roller滚轴
baffle plate挡块
located block定位块
supporting block for location
定位支承块
air cushion plate气垫板
air-cushion eject-rod气垫顶杆trimming punch切边冲子
stiffening rib punch = stinger 加强筋冲子ribbon punch压筋冲子
reel-stretch punch卷圆压平冲子
guide plate定位板
sliding block滑块
sliding dowel block滑块固定块
active plate活动板
lower sliding plate下滑块板
upper holder block上压块
upper mid plate上中间板
spring box弹簧箱
spring-box eject-rod弹簧箱顶杆spring-box eject-plate弹簧箱顶板bushing bolck衬套
cover plate盖板
guide pad导料块
塑件&模具相关英文compression molding压缩成型
flash mold溢流式模具
plsitive mold挤压式模具
split mold分割式模具cavity型控母模
core模心公模
taper锥拔
leather cloak仿皮革
shiver饰纹
flow mark流痕
welding mark溶合痕
post screw insert螺纹套筒埋值
self tapping screw自攻螺丝
striper plate脱料板
piston活塞
cylinder汽缸套
chip细碎物
handle mold手持式模具
移转成型用模具
encapsulation molding低压封装成型射出成型用模具
two plate两极式(模具)
well type蓄料井
insulated runner绝缘浇道方式
hot runner热浇道
runner plat浇道模块
valve gate阀门浇口
band heater环带状的电热器spindle阀针spear head刨尖头
slag well冷料井
cold slag冷料渣
air vent排气道
h=0.02~0.05mm
w=3.2mm
L=3~5mm
welding line熔合痕
eject pin顶出针
knock pin顶出销
return pin回位销反顶针
sleave套筒
stripper plate脱料板
insert core放置入子
runner stripper plate浇道脱料板guide pin导销
eject rod (bar)(成型机)顶业捧subzero深冷处理
three plate三极式模具
runner system浇道系统
stress crack应力电裂orientation定向
sprue gate射料浇口,直浇口nozzle射嘴
sprue lock pin料头钩销(拉料杆) slag well冷料井
side gate侧浇口
edge gate侧缘浇口
tab gate搭接浇口
film gate薄膜浇口
flash gate闸门浇口
slit gate缝隙浇口
fan gate扇形浇口
dish gate因盘形浇口
H=F=1/2t~1/5t
T=2.5~3.5mm
diaphragm gate隔膜浇口
ring gate环形浇口
subarine gate潜入式浇口
tunnel gate隧道式浇口
pin gate针点浇口
Φ0.8~1.0mm
Runner less无浇道
(sprue less)无射料管方式
long nozzle延长喷嘴方式
sprue浇口;溶渣
品质人员名称类
QC quality control 品质管理人员
FQC final quality control 终点质量管理人员IPQC in process quality control 制程中的质量管理人员
OQC output quality control 最终出货质量管理人员IQC incoming quality control 进料质量管理人员TQC total quality control 全面质量管理
POC passage quality control 段检人员
QA quality assurance 质量保证人员
OQA output quality assurance 出货质量保证人员QE quality engineering 品质工程人员
品质保证类
FAI first article inspection 新品首件检查
FAA first article assurance 首件确认
TVR tool verification report 模具确认报告
3B 3B 模具正式投产前确认
CP capability index 能力指数
CPK capability index of process 模具制程能力参数SSQA standardized supplier quality audit 合格供货商品质评估
OOBA out of box audit 开箱检查
QFD quality function deployment 品质机能展开FMEA failure model effectiveness analysis 失效模式分析
8 disciplines 8项回复内容FA final audit 最后一次稽核
CAR corrective action request 改正行动要求corrective action report 改正行动报告
FQC运作类
AQL Acceptable Quality Level 运作类允收品质水准
S/S Sample size 抽样检验样本大小
ACC Accept 允收
REE Reject 拒收
CR Critical 极严重的
MAJ Major 主要的
MIN Minor 轻微的
AOQ Average Output Quality 平均出厂品质AOQL Average Output Quality Level 平均出厂品质Q/R/S Quality/Reliability/Service 品质/可靠度服务MIL-STD Military-Standard 军用标准
S I-S IV Special I-Special IV 特殊抽样水准等级
P/N Part Number 料号
L/N Lot Number 批号
AOD Accept On Deviation 特采
UAI Use As It 参照件
FPIR First Piece Inspection Report 首件检查报告PPM Percent Per Million 百万分之一
制程统计品管专类
SPC Statistical Process Control 统计制程管制SQC Statistical Quality Control 统计质量管理
R Range 全距
AR Averary Range 全距平均值
UCL Upper Central Limit 管制上限
LCL Lower Central Limit 管制下限
MAX Maximum 最大值
MIN Minimum 最小值
GRR Gauge Reproducibility&Repeatability 量具之再制性及重测性判断量可靠与否
DIM Dimension 尺寸
DIA Diameter 直径
FREQ Frequency 频率
N Number 样品数
其它品质术语类
QCC Quality Control Circle 品质圈
QIT Quality Improvement Team 品质改善小组PDCA Plan Do Check Action 计划执行检查总结
ZD Zero Defect 零缺点
QI Quality Improvement 品质改善
QP Quality Policy 目标方针
TQM Total Quality Management 全面品质管理MRB Material Reject Bill 退货单
LQL Limiting Quality Level 最低品质水准
RMA Return Material Audit 退料认可
QAN Quality Amelionrate Notice 品质改善活动ADM Absolute Dimension Measuremat 全尺寸测量QT Quality Target 品质目标
7QCTools 7 Quality Controll Tools 品管七大手法通用之件类
ECN Engineering Change Notes 工程变更通知(供货商)
ECO Engineering Change Order 工程改动要求(客户)
PCN Process Change Notice 工序改动通知
PMP Product Management Plan 生产管制计划
SIP Specification In Process 制程检验规格
SOP Standard Operation Procedure 制造作业规范IS Inspection Specification 成品检验规范
BOM Bill Of Material 物料清单
PS Package Specification 包装规范
SPEC Specification 规格
DWG Drawing 图面
系统文件类
QS Quality System 品质系统
ES Engineering Standarization 工程标准
H Huston (美国)休斯敦IWS International Workman Standard 工艺标准
ISO International Standard Organization 国际标准化组织
GS General Specification 一般规格
CMCS C-China M-Manufact C-Compaq S-Stamping Compaq产品在龙华冲压厂制造作业规范
CQCA Q-Quality A-Assembly Compaq产品在龙华组装厂品管作业规范
CQCP P-Painting Compaq产品在龙华烤漆厂品管作业规范
部类
PMC Production & Material Control 生产和物料控制
PPC Production Plan Control 生产计划控制
MC Material Control 物料控制
ME Manafacture Engineering 制造工程部
PE Project Engineering 产品工程部
A/C Accountant Dept 会计部
P/A Personal & Administration 人事行政部
DC Document Center 资料中心
QE Quality Engineering 品质工程(部)
QA Quality Assurance 品质保证(处)
QC Quality Control 质量管理(课)
PD Product Department 生产部
LAB Labratry 实验室
IE Industrial Engineering 工业工程
R&D Research & Design 设计开发部
P Painting 烤漆(厂)
A Asssembly 组装(厂)
S Stamping 冲压(厂)
生产类
PCS Pieces 个(根,块等)
PRS Pairs 双(对等)
CTN Carton 卡通箱
PAL Pallet/skid 栈板
PO Purchasing Order 采购订单
MO Manufacture Order 生产单
D/C Date Code 生产日期码
ID/C Identification Code (供货商)识别码
SWR Special Work Request 特殊工作需求
L/N Lot Number 批号
P/N Part Number 料号
其它
OEM Original Equipment Manufacture 原设备制造PCE Personal Computer Enclosure 个人计算机外设PC Personal Computer 个人计算机
CPU Central Processing Unit 中央处理器
SECC SECC` 电解片
SGCC SGCC 热浸镀锌材料
PRC People's Republic of China 中国大陆
U.S.A the United States of America 美国
A.S.A.P As Soon As Possible 尽可能快的
E-MAIL Electrical-Mail 电子邮件
N/A Not Applicable 不适用
QTY Quantity 数量
VS 以及
REV Revision 版本
JIT Just In Time 零库存
I/O Input/Output 输入/输出
OK Ok 好
NG Not Good 不行,不合格
C=0 Critical=0 极严重不允许
ESD Electry-static Discharge 静电排放
5S 希腊语整理,整顿,清扫,清洁,教养
ATIN Attention 知会
CC Carbon Copy 副本复印相关人员
APP Approve 核准,认可,承认
CHK Check 确认
AM Ante Meridian 上午
PM Post Meridian 下午
CD Compact Disk 光盘
CD-ROM Compact Disk Read-Only Memory 只读光盘
FDD Floppy Disk Drive 软盘机
HDD Hard Disk Drive 碟碟机
REF Reference 仅供参考
CONN Connector 连接器
CAV Cavity 模穴
CAD Computer Aid Design 计算器辅助设计
ASS'Y Assembly 装配,组装
MAT'S Material 材料
IC Integrated Circuit 集成电路
T/P True Position 真位度
TYP Type 类型
WDR Weekly Delivery Requitement 周出货需求
C/T Cycle Time 制程周期
L/T Lead Time 前置时间(生产前准备时间)
S/T Standard Time 标准时间
P/M Product Market 产品市场
3C Computer,Commumcation,Consumer electronic's 消费性电子
5WIH When,Where,Who,What,Why,How to
5M Man,Machine,Material,Method,Measurement
4MIH Man,Materia,Money,Method,Time 人力,物力,财务,技术,时间(资源)
SQA Strategy Quality Assurance 策略品质保证DQA Desigh Quality Assurance 设计品质保证MQA Manufacture Quality Assurance 制造品质保证
SSQA Sales and service Quality Assurance 销售及服务品质保证
LRR Lot Rejeet Rate 批退率
BS Brain storming 脑力激荡
EMI Electronic Magnetion Inspect 高磁测试
FMI Frequency Modulatim Inspect 高频测试
B/M Boar/Molding(flat cable)
C/P Connector of PC
A/P Assembly
SPS Switching power supply 电源箱
DT Desk Top 卧式(机箱)
MT Mini-Tower 立式(机箱)
DVD Digital Vedio Disk
VCD Vdeio Compact Disk
LCD Liquid Crystal Display
CAD Computer AID Design
CAM Computer AID Manufacturing
CAE Computer AID Engineering
ABIOS Achanced Basic in put/output system 先进的基本输入/输出系统
CMOS Complemeruary Metoll Oxide Semiconductor 互补金属氧化物半导体
PDA Personal Digital Assistant 个人数字助理
IC Integrated Circuit 集成电路
ISA Industry Standard Architecture 工业标准体制结构
MCA Micro Channel Architecture 微信道结构EISA Extended Industry Standard Architecture 扩充的工业标准结构
SIMM Single in-line memory module 单项导通汇流组件
DIMM Dual in-line Memory Module 双项导通汇流组件
LED Light-Emitting Diode 发光二级管
FMEA Failure Mode Effectivenes 失效模式分析
W/H Wire Harness 金属线绪束集组件
F/C Flat Calle 排线
PCB Printed Circuit Board 印刷电路板
CAR Correction Action Report 改善报告
NG Not Good 不良
WPR Weekly Delivery Requirement 周出货要求PPM Parts Per Million 百万分之一
TPM Total Production Maintenance 全面生产保养MRP Material Requiremcnt Planning 物料需计划OC Operation System 操作系统TBA To Be Design 待定,定缺
D/C Drawing Change
P/P Plans & Procedune
EMI Electrical-Music Industry 电子音乐工业
RFI Read Frequency Input 读频输入
MMC Maximum Material Condition
MMS Maximum Material Size
LMC Least Material Condition
LMS Least Material Size
------------------------------------------------------------------------------------------
模具技术用语
各种模具常用成形方式
accurate die casting 精密压铸powder forming 粉末成形
calendaring molding 压延成形powder metal forging 粉末锻造
cold chamber die casting 冷式压铸precision forging 精密锻造
cold forging 冷锻press forging 冲锻
compacting molding 粉末压出成形rocking die forging 摇动锻造
compound molding 复合成形rotary forging 回转锻造compression molding 压缩成形rotational molding 离心成形
dip mold 浸渍成形rubber molding 橡胶成形encapsulation molding 注入成形sand mold casting 砂模铸造
extrusion molding 挤出成形shell casting 壳模铸造foam forming 发泡成形sinter forging 烧结锻造forging roll 轧锻six sides forging 六面锻造
gravity casting 重力铸造slush molding 凝塑成形hollow(blow) molding 中空(吹出)成形squeeze casting 高压铸造
hot chamber die casting 热室压铸swaging 挤锻
hot forging 热锻transfer molding 转送成形
injection molding 射出成形warm forging 温锻investment casting 精密铸造matched die method 对模成形法
laminating method 被覆淋膜成形low pressure casting 低压铸造
lost wax casting 脱蜡铸造matched mould thermal forming 对模热成形模
各式模具分类用语
bismuth mold 铋铸模landed plunger mold 有肩柱塞式模具
burnishing die 挤光模landed positive mold 有肩全压式模具
button die 镶入式圆形凹模loading shoe mold 料套式模具
center-gated mold 中心浇口式模具loose detail mold 活零件模具
chill mold 冷硬用铸模loose mold 活动式模具
clod hobbing 冷挤压制模louvering die 百叶窗冲切模
composite dies 复合模具manifold die 分歧管模具counter punch 反凸模modular mold 组合式模具double stack mold 双层模具multi-cavity mold 多模穴模具
electroformed mold 电铸成形模multi-gate mold 复式浇口模具
expander die 扩径模offswt bending die 双折冷弯模具
extrusion die 挤出模palletizing die 迭层模
family mold 反套制品模具plaster mold 石膏模blank through dies 漏件式落料模porous mold 通气性模具
duplicated cavity plate 复板模positive mold 全压式模具
fantail die 扇尾形模具pressure die 压紧模
fishtail die 鱼尾形模具profile die 轮廓模flash mold 溢料式模具progressive die 顺序模gypsum mold 石膏铸模protable mold 手提式模具hot-runner mold 热流道模具prototype mold 雏形试验模具
ingot mold 钢锭模punching die 落料模
lancing die 切口模raising(embossing) 压花起伏成形re-entrant mold 倒角式模具sectional die 拼合模runless injection mold 无流道冷料模具sectional die 对合模具
segment mold 组合模semi-positive mold 半全压式模具
shaper 定型模套single cavity mold 单腔模具
solid forging die 整体锻模split forging die 拼合锻模split mold 双并式模具sprueless mold 无注道残料模具
squeezing die 挤压模stretch form die 拉伸成形模sweeping mold 平刮铸模swing die 振动模具
three plates mold 三片式模具trimming die 切边模unit mold 单元式模具universal mold 通用模具unscrewing mold 退扣式模具yoke type die 轭型模
模具厂常用之标准零配件
air vent vale 通气阀anchor pin 锚梢
angular pin 角梢baffle 调节阻板
angular pin 倾斜梢baffle plate 折流檔板
ball button 球塞套ball plunger 定位球塞
ball slider 球塞滑块binder plate 压板
blank holder 防皱压板blanking die 落料冲头
bolster 上下模板bottom board 浇注底板
bolster 垫板bottom plate 下固定板
bracket 扥架bumper block 缓冲块
buster 堵口casting ladle 浇注包
casting lug 铸耳cavity 模穴(模仁)
cavity retainer plate 模穴扥板center pin 中心梢clamping block 锁定块coil spring 螺旋弹簧
cold punched nut 冷冲螺母cooling spiral 螺旋冷却栓
core 心型core pin 心型梢
cotter 开口梢cross 十字接头
cushion pin 缓冲梢diaphragm gate 盘形浇口
die approach 模头料道die bed 型底
die block 块形模体die body 铸模座
die bush 合模衬套die button 冲模母模
die clamper 夹模器die fastener 模具固定用零件
die holder 母模固定板die lip 模唇
die plate 冲模板die set 冲压模座
direct gate 直接浇口dog chuck 爪牙夹头
dowel 定位梢dowel hole 导套孔
dowel pin 合模梢dozzle 辅助浇口
dowel pin 定位梢draft 拔模锥度
draw bead 张力调整杆drive bearing 传动轴承ejection pad 顶出衬垫ejector 脱模器
ejector guide pin 顶出导梢ejector leader busher 顶出导梢衬套
ejector pad 顶出垫ejector pin 顶出梢
ejector plate 顶出板ejector rod 顶出杆
ejector sleeve 顶出衬套ejector valve 顶出阀
eye bolt 环首螺栓filling core 椿入蕊
film gate 薄膜形浇口finger pin 指形梢
finish machined plate 角形模板finish machined round plate 圆形模板
fixed bolster plate 固定侧模板flanged pin 带凸缘销flash gate 毛边形浇口flask 上箱
floating punch 浮动冲头gate 浇口
gate land 浇口面gib 凹形拉紧销
goose neck 鹅颈管guide bushing 引导衬套
guide pin 导梢guide post 引导柱
guide plate 导板guide rail 导轨
head punch 顶镦冲头headless punch 直柄冲头heavily tapered solid 整体模蕊盒hose nippler 管接头impact damper 缓冲器injection ram 压射柱塞
inlay busher 嵌入衬套inner plunger 内柱塞
inner punch 内冲头insert 嵌件insert pin 嵌件梢king pin 转向梢
king pin bush 主梢衬套knockout bar 脱模杵
land 合模平坦面land area 合模面
leader busher 导梢衬套lifting pin 起模顶销
lining 内衬locating center punch 定位中心冲头locating pilot pin 定位导梢locating ring 定位环
lock block 压块locking block 定位块
locking plate 定位板loose bush 活动衬套
making die 打印冲子manifold block 歧管档块master plate 靠模样板match plate 分型板
mold base 塑料模座mold clamp 铸模紧固夹
mold platen 模用板moving bolster 换模保持装置moving bolster plate 可动侧模板one piece casting 整体铸件
parallel block 平行垫块paring line 分模线
parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pilot pin 导销
pin gate 针尖浇口plate 衬板
pre extrusion punch 顶挤冲头punch 冲头
puncher 推杆pusher pin 衬套梢
rack 机架rapping rod 起模杆
re-entrant mold 凹入模retainer pin 嵌件梢
retainer plate 扥料板return pin 回位梢
riding stripper 浮动脱模器ring gate 环型浇口
roller 滚筒runner 流道
runner ejector set 流道顶出器runner lock pin 流道拉梢
screw plug 头塞set screw 固定螺丝
shedder 脱模装置shim 分隔片
shoe 模座之上下模板shoot 流道
shoulder bolt 肩部螺丝skeleton 骨架
slag riser 冒渣口slide(slide core) 滑块
slip joint 滑配接头spacer block 间隔块
spacer ring 间隔环spider 模蕊支架
spindle 主轴sprue 注道
sprue bushing 注道衬套sprue bushing guide 注道导
套
sprue lock bushing 注道定位衬套sprue puller 注道拉料销
spue line 合模线square key 方键
square nut 方螺帽square thread 方螺纹
stop collar 限位套stop pin 止动梢
stop ring 止动环stopper 定位停止梢
straight pin 圆柱销stripper bolt 脱料螺栓
stripper bushing 脱模衬套stripper plate 剥料板stroke end block 行程止梢submarine gate 潜入式浇口
support pillar 支撑支柱/顶出支柱support pin 支撑梢supporting plate 扥板sweep templete 造模刮板
tab gate 辅助浇口taper key 推拔键
taper pin 拔锥梢/锥形梢teeming 浇注
three start screw 三条螺纹thrust pin 推力销
tie bar 拉杵tunnel gate 隧道形浇口
vent 通气孔wortle plate 拉丝模板
模具常用之工作机械
3D coordinate measurement 三次元量床boring machine 搪孔机
cnc milling machine CNC铣床contouring machine 轮廓锯床
copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形刨床
cylindrical grinding machine 外圆磨床die spotting machine 合模机
drilling machine 钻孔机engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床
graphite machine 石墨加工机horizontal boring machine 卧式搪孔机
horizontal machine center 卧式加工制造中心internal cylindrical machine 内圆磨床jig boring machine 冶具搪孔机jig grinding machine 冶具磨床
lap machine 研磨机machine center 加工制造中心multi model miller 靠磨铣床NC drilling machine NC 钻床
NC grinding machine NC磨床NC lathe NC车床
NC programming system NC程序制作系统planer 龙门刨床
profile grinding machine 投影磨床projection grinder 投影磨床
radial drilling machine 旋臂钻床shaper 牛头刨床surface grinder 平面磨床try machine 试模机
turret lathe 转塔车床universal tool grinding machine 万能工具磨床
vertical machine center 立式加工制造中心wire E.D.M. 线割放电加工机
检验量测工具用语
autocollimator 自动准直机bench comparator 比长仪block gauge 块规bore check 精密小测定器calibration 校准caliper gauge 卡规
check gauge 校对规clearance gauge 间隙规clinoretee 测斜仪comparator 比测仪
cylinder square 圆筒直尺depth gauge 测深规
dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规
inside calipers 内卡钳inside micrometer 内分厘卡interferometer 干涉仪leveling block 平台
limit gauge 限规micrometer 测微计
mil 千分之一吋monometer 压力计
morse taper gauge 莫氏锥度量规nonius 游标卡尺optical flat 光学平晶optical parallel 光学平行passimeter 内径仪position scale 位置刻度
profile projector 轮廓光学投影仪protractor 分角器radius 半径ring gauge 环规
sine bar 正弦量规snap gauge 卡模
square master 直角尺stylus 触针
telescopic gauge 伸缩性量规working gauge 工作量规
模具钢材
alloy tool steel 合金工具钢aluminium alloy 铝合金钢bearing alloy 轴承合金blister steel 浸碳钢bonderized steel sheet 邦德防蚀钢板carbon tool steel 碳素工具钢
clad sheet 被覆板clod work die steel 冷锻模用钢emery 金钢砂ferrostatic pressure 钢铁水静压力forging die steel 锻造模用钢galvanized steel sheet 镀锌铁板
hard alloy steel 超硬合金钢high speed tool steel 高速度工具钢
hot work die steel 热锻模用钢low alloy tool steel 特殊工具钢
low manganese casting steel 低锰铸钢marging steel 马式体高强度热处理钢
martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢
meehanite metal 米汉纳铁merchant iron 市售钢材molybdenum high speed steel 钼系高速钢molybdenum steel 钼钢
nickel chromium steel 镍铬钢prehardened steel 顶硬钢
silicon steel sheet 硅钢板stainless steel 不锈钢
tin plated steel sheet 镀锡铁板tough pitch copper 韧铜
troostite 吐粒散铁tungsten steel 钨钢
vinyl tapped steel sheet 塑料覆面钢板
表面处理关连用语
age hardening 时效硬化ageing 老化处理
air hardening 气体硬化air patenting 空气韧化annealing 退火anode effect 阳极效应
anodizing 阳极氧化处理atomloy treatment 阿扥木洛伊表面
austempering 奥氏体等温淬火austenite 奥斯田体/奥氏体
bainite 贝氏体banded structure 条纹状组织
barrel plating 滚镀barrel tumbling 滚筒打光blackening 染黑法blue shortness 青熟脆性bonderizing 磷酸盐皮膜处理box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀
bright heat treatment 光辉热处理bypass heat treatment 旁路热处理
carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳cementite 炭化铁
chemical plating 化学电镀chemical vapor deposition 化学蒸镀
coarsening 结晶粒粗大化coating 涂布被覆
cold shortness 低温脆性comemtite 渗碳体controlled atmosphere 大气热处理corner effect 锐角效应
creeping discharge 蠕缓放电decarburization 脱碳处理
decarburizing 脱碳退火depth of hardening 硬化深层diffusion 扩散diffusion annealing 扩散退火electrolytic hardening 电解淬火embossing 压花etching 表面蚀刻ferrite 肥粒铁
first stage annealing 第一段退火flame hardening 火焰硬化
flame treatment 火焰处理full annealing 完全退火gaseous cyaniding 气体氧化法globular cementite 球状炭化铁
grain size 结晶粒度granolite treatment 磷酸溶液热处理
graphitizing 石墨退火hardenability 硬化性hardenability curve 硬化性曲线hardening 硬化
heat treatment 热处理hot bath quenching 热浴淬火hot dipping 热浸镀induction hardening 高周波硬化ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理
ion plating 离子电镀isothermal annealing 等温退火liquid honing 液体喷砂法low temperature annealing 低温退火
malleablizing 可锻化退火martempering 麻回火处理martensite 马氏体/硬化铁炭metallikon 金属喷镀法metallizing 真空涂膜nitriding 氮化处理nitrocarburizing 软氮化normalizing 正常化
oil quenching 油淬化overageing 过老化overheating 过热pearlite 针尖组织
phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀
plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化press quenching 加压硬化process annealing 制程退火
quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕quenching distortion 淬火变形
quenching stress 淬火应力reconditioning 再调质recrystallization 再结晶red shortness 红热脆性residual stress 残留应力retained austenite 残留奥rust prevention 防蚀salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 时效处理
second stage annealing 第二段退火secular distortion 经年变形
segregation 偏析selective hardening 部分淬火
shot blast 喷丸处理shot peening 珠击法
single stage nitriding 等温渗氮sintering 烧结处理soaking 均热处理softening 软化退火
solution treatment 固溶化热处理spheroidizing 球状化退火
stabilizing treatment 安定化处理straightening annealing 矫直退火
strain ageing 应变老化stress relieving annealing 应力消除退火
subzero treatment 生冷处理supercooling 过冷surface hardening 表面硬化处理temper brittleness 回火脆性
temper colour 回火颜色tempering 回火
tempering crack 回火裂痕texture 咬花
thermal refining 调质处理thermoechanical treatment 加工热处理
time quenching 时间淬火transformation 变态tufftride process 软氮化处理under annealing 不完全退火
vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理
vacuum hardening 真空淬火vacuum heat treatment 真空热处理
vacuum nitriding 真空氮化water quenching 水淬火wetout 浸润处理
焊接用语
acetylene 乙炔ampere 电流安培
angle welding 角焊arc 电弧
argon arc welding 氩弧焊接bare electrode 光熔接条butt welding 对接焊接camber 电弧弯曲
cascade 阶迭熔接法clad weld 被覆熔接
crator 焊疤excess metal 多余金属
filler rod 焊条fillet weld 填角焊接
gas shield 气体遮蔽groove welding 起槽熔接
hand face shield 手握面罩hard facing 硬表面堆焊
jig welding 工模焊接laser beam welding 雷射光焊接metal electrode insert gas welding MIG熔接nugget 点焊熔核
overlaying 堆焊peening of welding 珠击熔接法
plug welding 塞孔熔接positioned welding 正向熔接pressure welding 压焊propane gas cutting 丙烷气切
生产制造管理中常用英文单词缩写 1. A/D/V Analysis/Development/Validation 分析/发展/验 证 AA Approve Architecture 审批体系 ACD Actual Completion Date 实际完成日期 ALBS Assembly Line Balance System 装配线平衡系统 ANDON 暗灯(安腾灯) AP Advanced Purchasing 提前采购 API Advanced Product Information 先进的产品信息APQP Advanced Product Quality Planning 先期产品质量策划 ATT Actual Tact Time 实际单件工时 BIQ Building in Quality 制造质量 BIW Body In White 白车身 BOD Bill of Design 设计清单 BOE Bill of Equipment 设备清单 BOL Bill of Logistic 装载清单 BOM Bill of Material 原料清单 BOP Bill of Process 过程清单 BPD Business Plant Deployment 业务计划实施 CAD Computer-Aided Design 计算机辅助设计 CAE Computer-Aided Engineering 计算机辅助工程(软件) CARE Customer Acceptance & Review Evaluation 用户接受度和审查评估 CAS Concept Alternative Selection 概念可改变的选择CIP Continue Improve Process 持续改进 CIT Compartment Integration Team 隔间融合为组 CKD Complete Knockdown 完全拆缷 CMM Coordinate Measuring Machines 坐标测量仪 CPV Cost per Vehicle 单车成本 CR&W Controls/Robotics & Welding 控制/机器人技术和焊接 CS Contract Signing 合同签订
一:常用術語 Hon Hai 鴻海 CMM Component module move 機動元件整合 CEM Contract Manu faction service 合約委托代工 IBSC Internet Business Solution Center 國際互聯網應用中心 PCEG Personal Computer Enclosure group 個人電腦外設事業群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鴻富錦事業群 SABG system assembly business group 系統組裝事業群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鴻準 Stamping tool shop I 沖模一廠 Stamping tool shop II 沖模二廠 Prototype workshop 樣品中心 Steel factory 裁剪廠 PCE molding tooling workshop PCE塑模廠 Hua Nan test and measurement center 華南檢測中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 鎂合金 Engineer standard 工標 Document center (database center)資料中心 Design Center 設計中心 Painting 烤漆(廠) Assembly組裝(廠) Stamping 沖壓(廠) Education and Training教育訓練 proposal improvement/creative suggestion提案改善 Technological exchange and study 技術交流研習會 Technology and Development Committee 技術發展委員會 BS Brain Storming 腦力激蕩 QCC Quality Control Circle 品質圈 PDCA Plan Do Check Action 計劃執行檢查總結 DCC delivery control center 交貨管制中心 3C Computer 電腦類產品 Consumer electronics 消費性電子產品 Communication 通訊類產品 Core value(核心价值) Love 愛心
生产车间常用名称翻译 仓库:WAREHOUSE 脱包间:REMOVING BAG ROOM 楼梯口:THE STAIRS 原料传递口:RAW MATERIAL TRANSFER PORT 原料间:RAW MATERIAL ROOM 称量间:WEIGHING ROOM 清洗间:WASHING ROOM 一次更衣室:DRESSING ROOM 二次更衣室:DRESSING ROOM 缓冲间:BUFFERING ROOM 2个 洁具间:SANITARY TOOL ROOM 2个 器具存放间:TOOLS STORAGE ROOM 2个 制作间:MIXING ROOM 更衣室:DRESSING ROOM 3个 安全出口:EXIT 3个红色字 传递口:CONNECTING WINDOW 7个灌装间:FILLING ROOM 半成品储存间:SEMI FINISHED PRODUCTS STORAGE 内包材间:INNER PACKAGE MATERIAL ROOM 女更衣室:WOMEN'S DRESSING ROOM 男更衣室:MEN'S DRESSING ROOM 女一更衣室:WOMEN'S DRESSING ROOM NO.1 男一更衣室:MEN'S DRESSING ROOM NO.1 女二更衣室:WOMEN'S DRESSING ROOM NO.2 男二更衣室:MEN'S DRESSING ROOM NO.2 成品组装间:FINISHED PRODUCTS ASSEMBLING ROOM 外包装车间:OUTER PACKAGING ROOM 2个 女洗手间:WOMEN’S WASHROOM 货梯严禁乘坐:PERMITTED UNLESS PRODUCTS INCLUDED. 研发室:RESEARCH AND DEVELOPMENT ROOM 微检室:MICROBIOLOGICAL TEST ROOM 打样间:SAMPLING ROOM 留样间:SAMPLES STORAGE ROOM 总更衣室:MAIN DRESSING ROOM 办公室:OFFICE
接机到送酒店: 1.Excuse me. Are you XXX from XXXX?对不起,你是来自XX公司的XX吗? 2. I'm XXX. I am here to meet you today.我是XX,今天我到这里来接你。 3. I'll show you to your hotel.我带你去旅馆。 4.How was your flight? Was it comfortable?你坐的班机怎么样?还舒服吗?It was quite good.But it was awfully long.班机很好,就是时间太长了。 5.Did you have a good flight?你旅途愉快吗? Not really, I'm afraid. We were delayed taking off, and we encountered a lot of bad weather.不太好,我们起飞延误了,还遭遇了恶劣的气候。 6.Did you get any sleep on the plane?你在飞机上睡觉了吗? 7.We have booked a hotel for you.我们已经帮你预定了酒店 8.Does it take long to go to hotel from here?从此地去台北要很久吗? It’s about an hour.大概要一个小时。 9.I’ve brought my car, so I can drive you to your hotel.我开车来的,所以我开车送你到旅馆。 10.You must be hungry. Shall we get something to eat?你一定饿了,我们吃点东西好吗?How about get something at the hotel restaurant.我们 就到旅馆餐厅吃点东西怎么样。/Would you like to have some dinner?你想吃饭吗? What would you like to eat?你想吃什么呢?/Can I take you out to dinner? It'll be my treat.我带你出去吃饭好吗?这次我请客。/If you’re hungry, we can eat dinner now.如果你饿了,我们现在就去吃饭。 11. I hope you don’t mind having Chinese food for lunch、dinner.希望你不要介意午餐或晚餐吃中国菜
硬件类常用英语词汇 下面是小编整理的硬件类常用英语词汇,希望对大家有帮助。 计算机英语词汇大全 常见硬件篇 CPU:Central Processing Unit,中央处理单元,又叫中央处理器或微处理器,被喻为电脑的心脏。 LD:Laser Disk,镭射光盘,又称激光视盘。 CD:Compact Disc,压缩光盘,又称激光唱盘。 CD-ROM:Compact Disc-Read Only Memory,压缩光盘-只读记忆(存储),又叫“只读光盘”。 VCD:Video Compact Disc,视频压缩光盘,即人们通常所说的“小影碟”。 RAM:Random Access Memory,随机存储器,即人们常说的“内存”。 ROM:Read-Only Memory,只读存储器。 Seagate:美国希捷硬盘生产商。Seagate英文意思为“通往海洋的门户”,常指通海的运河等。 Quantum:英文含意为“定量,总量”。著名硬盘商标,美国昆腾硬盘生产商(Quantum Corporation)。
Maxtor:“水晶”,美国Maxtor硬盘公司。 PCI:Peripheral Component Interconnection,局部总线(总线是计算机用于把信息从一个设备传送到另一个设备的高速通道)。PCI总线是目前较为先进的一种总线结构,其功能比其他总线有很大的提高,可支持突发读写操作,最高传输率可达132Mbps,是数据传输最快的总线之一,可同时支持多组外围设备。PCI不受制于 CPU处理器,并能兼容现有的各种总线,其主板插槽体积小,因此成本低,利于推广。 EDO:Extended Data Output,扩充数据输出。当CPU的处 理速度不断提高时,也相应地要求不断提高DRAM传送数据速度, 一般来说,FPM(Fast Page Model)DRAM传送数据速度在60-70ns,而EDO DRAM比FPM快3倍,达20ns。目前最快的是SDRAM(Synchronous DRAM,同步动态存储器),其存取速度高 达10ns。 SDRAM:Synchronous Dynamic Random Access Memory,同步动态随机存储器,又称同步DRAM,为新一代动态 存储器。它可以与CPU总线使用同一个时钟,因此,SDRAM存储 器较EDO存储器能使计算机的性能大大提高。 Cache:英文含义为“(勘探人员等贮藏粮食、器材等的)地窖; 藏物处”。电脑中为高速缓冲存储器,是位于CPU和主存储器 DRAM(Dynamic Randon Access Memory)之间,规模较小,但 速度很高的存储器,通常由SRAM(Static Random Access
从事质量工作以来积累的常用英语,希望对有需要的朋友有所帮助!质量专业英语大全零件材料类的专有名词 CPU: central processing unit(中央处理器) IC: Integrated circuit(集成电路) Memory IC: Memory Integrated circuit(记忆集成电路) RAM: Random Access Memory(随机存取内存) DRAM: Dynamic Random Access Memory(动态随机存取内存)SRAM: Staic Random Access Memory(静态随机内存) ROM: Read-only Memory(只读存储器) EPROM:Electrical Programmable Read-only Memory (电可抹只读存诸器) EEPROM: Electrical Erasbale Programmable Read-only Memory(电可抹可编程只读存储器) CMOS: Complementary Metal-Oxide-Semiconductor (互补金属氧化物半导体) BIOS: Basic Input Output System(基本输入输出系统)Transistor:晶体管 LED:发光二极管 Resistor:电阻 Variator:可变电阻
Capacitor:电容 Capacitor array:排容Diode:二极管 Transistor:三极体Transformer:变压器(ADP)Oscillator:频率振荡器(0sc)Crystal:石英振荡器 XTAL/OSC:振荡产生器(X)Relay:延时器 Sensor:感应器 Bead core:磁珠 Filter:滤波器 Flat Cable:排线 Inductor:电感 Buzzer:蜂鸣器 Socket:插座 Slot:插槽 Fuse:熔断器 Current:电流表 Solder iron:电烙铁Magnifying glass:放大镜Caliper:游标卡尺
工廠常用英語翻譯(機械、模具) 总经理办公室General manager’s office 模具部Tooling department 项目部Project department品质部Quality department计划 部 Plan department 制造部Manufacture department产品部Keypad departmentIMD 产品部 IMD department五金部 Metal stamping department设计科 Design section冲压车间 Stamping workshop电镀车间 Plating workshop物控科 Production material control section 计划 科 Plan section 仓务科 Warehouse section商务科 Business section品质规划科 quality plan section IQC科 IQC sectionIPQC科 IPQC sectionOQC科 OQC section检测中心 measurement center 项目规划科 Project plan section项目XX科 Project section XX试模科 Mold test section成本科 Cost section 设备科 Facility section采购科 Purchase section综合办 General affairs office 编程科 Programming section 模具工程科 Tooling engineering section模具装配车间Mold assembly workshop文控中心 Document control center (DCC)注塑车间Injection workshop喷涂车间 Spray painting workshop装配车间Assembly workshop 总经理General manager (GM)经理managerXX部门经理Manager of XX department 原料库 Raw material warehouse半成品库 Semi-finished product warehouse成品库 Finished product warehouse科长 section chief 主任 chief 部门主管 department head主管, 线长supervisor组长Foreman, forelady秘书secretary 文员clerk操作员operator助理assistant职员staff 陶瓷ceramics合成纤维synthetic fibre电化学腐蚀electrochemical corrosion车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining车间workshop工程技术人员engineer气动夹紧pneuma lock 数学模型mathematical model画法几何descriptive geometry机械制图Mechanical drawing 投影projection视图view 剖视图profile chart 标准件standard component零件图part drawing 装配图assembly drawing尺寸标注size marking技术要求technical requirements 刚度rigidity内力internal force位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material刚度准则rigidity criterion 垫圈washer 垫片spacer直齿圆柱齿轮straight toothed spur gear斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint曲柄crank摇杆racker凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient求导derivation 定积分definite integral不定积分indefinite integral 曲率curvature偏微分partial differential 毛坯rough游标卡尺slide caliper千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant逆矩阵inverse matrix线性方程组linear equations 概率probability 随机变量random variable排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss轴线axes余子式cofactor
参观工厂之常用英语 WHY DON’T WE START AT THE WORKSHOP. MR …? 为什么不从工厂开始呢,MR…? LET ME TAKE YOU AROUND THE FACTORY. 让我带你到工厂四周看看。 I’M AFRAID YOU’LL HAVE TO WEAR AN OVERALL. IT’S A HYGIENE REQUIREMENT. 请穿上工作服,这是卫生上的要求。 YOU NEED THIS FOR SECURITE. 你需要使用这个,以保证安全。 AT PRESENT, THERE ARE 968 WORKERS AT THE MANUFACTERING PLANT. 目前,这座制造厂有员工968人。 WATCH YOUR STEP. 当心你的脚下。
I’m not familiar with that point. Let me call someone who is more knowledgeable. 关于那一点我不太熟悉。让我打电话给比较了解情况的人。 It’s very important not to touch the machinery. 不要触摸机器很重要。 Pls come this way. 请这边走。 Our company deals in a wide range of related products. 本公司经营一系列相关产品。 How big is your company? 贵公司的规模有多大? What is your market share? 贵公司的市场占有率是多少? I’m not familiar with that part. 那一部分我不熟悉。
常用词汇 主厂房main power building 设备缺陷equipment defect 缺陷处理defect treatment 设备规范Specification of equipment 铭牌nameplate 接线盒terminal box 热网heating network 电网network 供货范围scope of supply 参数parameter 停机, 停运outage 皮带速度belt velocity 皮带传输belt conveyor 蒸汽参数steam condition 蒸发量generation rates 功率因素power factor 输出负荷continuous rating output 额定蒸汽流量Max. continuous rating(MCR) 额定电压rated voltage 额定电流rated current 运行工况operation condition 值班员attendant 工日man-day 工时man-hour 事故甩负荷emergency load dump 四班三倒three shift by four teams 白班day shift 长白班regular shift 小休short-time off 大休long time-off 行灯safety lamp, 手锤hand hammer, 钢丝reinforcing wire 螺丝刀screw driver 测厚仪pachometer, 电筒electric torch 卡尺Sliding caliper 撬棒crowbar 手拉葫芦hand chain block 梯子Ladder, 扳手spanner 安全帽safety helmet 手套gloves 分包商sub-contractor 承包商contractor 土建civil work 工作票work order 操作票operation order
CORPORATE COMMON ABBREVIATION 常用语缩写 1 Organization组织 1-1 HQ Head Quarter 总公司 1-2Chairmen主席 1-3Lite-On Group光宝集团 1-4 President 总裁 1-5Executive Vice President 常务副总裁 1-6Vice President副总裁 1-7HR Human Resource人力资源部 1-8FIN Finance 财务 1-9Sales 销售 1-10R&D Research & Developing 研发部 1-11QA 质量保证QA DQA CS 1-12MIS Management Information System资讯管理系统1-13Pur 采购Purchasing 1-14IMD Image management division 影像管理事业部 1-15ITS information technology system 计算机部 1-16QRA quality reliability assurance 品保部 1-17MFG manufacturing 制造部 1-18PMC production &material control 生(产)物(料)管(理) 1-19 PRO Procuremnet 采购开发部
1-20 PMO Plant Manager Office 厂长室 1-21 CEO Chief Executive Officer 执行总裁 2 Materials 材料 2-1PC Production Control 生产控制 2-1-1MPS Mass Production Schedule 量产计划 2-1-2FGI Finished goods Inventory 成品存货 2-1-3UTS Units To Stock存货单元 2-1-4WIP Working In Process Inventory在制品 2-1-5C/T Cycle Time 循环时间,瓶颈 2-1-6WD Working Days 工作天 2-1-7MTD Month To Days 月初到今日(例如总表整理) 2-1-8YTD Year To Days 年初到今日 2-1-9 SO Sales Order 销售单 2-1-10MO Manufacture Order 制造单 2-1-11 BTO Build To Order 订单生产 2-1-12 P/N part number 料号 2-1-13 FCST Forecast 预测计划 2-1-14 W/O Working Order 工单 2-1-15 P/O Purchasing Order 采购单 2-1-16 VDS Vendor Delivery Schedule 厂商送货进度表2-1-17 D/C Delivery Order 交货单 2-2 MC Material Control材料控制
【文件编号】 中材科技风电叶片车间常用英语 受控状态__________ 发放编号__________ 编制:__________ 审核:__________ 批准:__________
目录 组件/Parts ....................................... 错误!未定义书签。 设备&工装/Equipments&Devices ..................... 错误!未定义书签。 材料/Material .................................... 错误!未定义书签。 玻纤类/Fabric ................................ 错误!未定义书签。 芯材类/ Core Material ........................ 错误!未定义书签。 耗材类/Consumables ........................... 错误!未定义书签。 辅材类/Adding Material ....................... 错误!未定义书签。 树脂&粘接胶/Resin &Glue ...................... 错误!未定义书签。 油漆&腻子/Paint& Filler ...................... 错误!未定义书签。 避雷系统/Lightning Protection System ............. 错误!未定义书签。 金属件/Metal Pieces .............................. 错误!未定义书签。 2.工艺过程常用中英文词汇对照表 ....................... 错误!未定义书签。 工序类/Procedure ................................. 错误!未定义书签。 模具调试/Mold Debug .............................. 错误!未定义书签。 来料检查/ Incoming Inspection .................... 错误!未定义书签。 铺层/Lamination .................................. 错误!未定义书签。 灌注&预固化/Infusion&Pre-curing .................. 错误!未定义书签。 粘接/Bonding ..................................... 错误!未定义书签。 后处理/ Post-processing .......................... 错误!未定义书签。 3. 缩写/ Abbreviation ................................ 错误!未定义书签。 4. 维修工艺/ Maintenance Craft ....................... 错误!未定义书签。 真空灌注工艺维修方案/Infusion Process ........... 错误!未定义书签。 维修流程/Repaire Flow Diagram ................ 错误!未定义书签。
MRP(material requirement planning)物料需求计划、MRPⅡ(manufacturing resource planning)制造企业资源计划和ERP(enterprise resource planning)企业资源计划,是企业管理信息系统发展的不同阶段。MPR主要对制造环节中的物流进行管理,使企业达到"既要保证生产又要控制库存"的目的;而MRPⅡ则集成了物流和资金流,将人、财、物,时间等各种资源进行周密计划,合理利用,以提高企业的竞争力;ERP它将供应链、企业业务流程和信息流程都囊括其中。由于ERP的概念流传最广,现在已经成为企业管理信息系统的代名词。 MIS(management information system)管理信息系统 PMC即Product material control 的缩写形式。是指对生产的计划与生产进度,以及物料的计划、跟踪、收发、存储、使用等各方面的监督与管理和废料的预防处理工作。PMC部主要有两方面的工作内容。即PC(生产计划、生产进度的管理)与MC(物料的计划、跟踪、收发、存储、使用等各方面的监督与管理,以及呆废料的预防与处理工作)。 R&D (Research & Development) 研发部 六标准差用来严格要求良率(Yield),一般而言相同的流程、程序,每重复一百万次只允许有三次或四次以下的错误,若达五次错误即是未达六标准差所设定的高良率水平 QC:Quality Control,品质控制,产品的质量检验,发现质量问题后的分析、改善和不合格品控制相关人员的总称.一般包括IQC(Incoming Quality Control来料检验),IPQC(In-Process Quality Control制程检验),FQC(Final Quality Control 成品检验),OQC(Out-going Quality Control出货检验),也有的公司不管三七
工厂专业英语术语 Assembly line组装线Layout布置图Conveyer流水线物料板Rivet table拉钉机Rivet gun拉钉枪Screw driver起子Pneumatic screw driver气动起子worktable 工作桌OO BA开箱检查fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板b arcode条码barcode scanner条码扫描器fuse together熔合fuse machine热熔机repair修理operator作业员QC品管supervisor 课长ME制造工程师MT制造生技cos metic inspect外观检查inner parts inspect内部检查thumb screw大头螺丝lbs. inch 镑、英寸EMI gasket导电条 front plate前板rear plate后板chassis 基座bezel panel面板 power button电源按键reset button重置键Hi-pot test of SPS高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts塑胶件SOP制造作业程序material check list物料检查表work cell工作间trolley台车carton纸箱sub-line支线left fork叉车personnel resource departmen t 人力资源部production department生产部门planning department企划部QC Secti on品管科 stamping factory冲压厂painting factory烤漆厂molding factory成型厂common e quipment常用设备uncoiler and straightener整平机 punching machine 冲床robot机械手hydraulic machine油压机 lathe车床planer |'plein?|刨床miller铣床grinder磨床 linear cutting线切割electrical sparkle电火花welder电焊机 staker=reviting machine铆合机position职务president董事长 general manager总经理special assistant manager特助 factory director厂长department director部长 deputy manager | =vice manager副理section supervisor课长 deputy section supervisor =vice section superisor副课长 group leader/supervisor组长line supervisor线长 assistant manager助理to move, to carry, to handle搬运 be put in storage入库pack packing包装to apply oil擦油 to file burr 锉毛刺final inspection终检to connect material接料 to reverse material 翻料wet station沾湿台Tiana天那水 cleaning cloth抹布to load material上料to unload material卸料 to return material/stock to退料scraped |'skr?pid|报废 scrape ..v.刮;削deficient purchase来料不良manufacture procedure制程deficient manufacturing procedure制程不良oxidation |' ksi'dei?n|氧化scratch刮伤dents压痕 defective upsiding down抽芽不良defective to staking铆合不良 embedded lump镶块feeding is not in place送料不到位 stamping-missing漏冲production capacity生产力 education and training教育与训练proposal improvement提案改善 spare parts=buffer备件forklift叉车trailer=long vehicle拖板车 compound die合模die locker锁模器pressure plate=plate pinch压板bolt螺栓administration/general affairs dept总务部automatic screwdriver电动启子thicknes s gauge厚薄规
base pan 基座 bezel 面板 flat cable 排线 resin film 树脂膜 raw materials原料 materials物料 steel plate钢板 roll/coil material卷料 spare parts =buffer备品 plastic parts塑料件 sheet metal parts/stamping parts 冲件 material check list物料检查表 finished product成品 semi-finished product半成品 good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品
disposed goods处理品 warehouse/hub仓库 packing material包材 basket蝴蝶竺 plastic basket胶筐 flow chart流程窗体 production tempo生产进度现状 lots of production生产批量 manufacture procedure制程 to revise, modify修订 to switch over to, switch—to, switching over切换engineering bottleneck, project difficulty工程瓶颈glove(s)手套 glove(s) with exposed fingers割手套 Band-Aid创可贴 Industrial alcohol工业酒精 broom扫把
电子制造业新产品导入NPI及常用英文词汇 产品定义(EVT),产品设计(DVT),定型测试(PVT) EVT (Engineer Verification Test)工程样品验证测试, DVT (Design Verification Test)设计样品验证测试, PVT(Production/Process/Pilot Verification Test)生产验证测试。 1)产品确证历程:EVT(Engineering Verification Test)---> DVT(Design Verification Test) ---> PVT(Process Verification Test); 2)EVT Poduct/Engineering Specification complete (由R&D 完成,容: 一些重要的参数,重要特征) Design Verification Plan ( B-test, Compatibility-test, EMI ) (由技服部作) 初步之BOM (R&D完成) Cost Review (PMP 负责) Test equipment and Tooling
(R&D 和工程部门) Test process documented and released 测试程序或测试文件 Failure analysis and corrective actions 针对不良点作设计上的改善 3)DVT Design Verification Test( B-test , Compatibility-test, EMI ) complete 概念1:可靠性测试: 产品在既定的时间, 在特定的条件下完成特定功能和性能的机率 概念2:B-test--- Basic test 包括: Function Test Safety Test Environment Test Mechanical Test 概念3:Safety Test 主要有: Hit-Pot 高压测试 绝缘电阻测试 Current Leakage(电流测试) 接地测试
一:常用术语 Hon Hai 鸿海 CMM Component module move 机动元件整合 CEM Contract Manu faction service 合约委托代工 IBSC Internet Business Solution Center 国际互联网应用中心 PCEG Personal Computer Enclosure group 个人计算机外设事业群(FOXTEQ)CCBG Connector& cable business group CPBG Competition business group ESBG Enterprise system business group 鸿富锦事业群 SABG system assembly business group 系统组装事业群 NWE Net Work Enclosure NSE Network system enclosure NSG Network system group NFE Network flexible enclosure Foxcavity = HZ = Hong Zhun 鸿准 Stamping tool shop I 冲模一厂 Stamping tool shop II 冲模二厂 Prototype workshop 样品中心 Steel factory 裁剪厂 PCE molding tooling workshop PCE塑模厂 Hua Nan test and measurement center 华南检测中心 MPE mobile phone enclosure MPE MBE mobile phone and notebook enclosure 明塑厂 MGE Alloy magnesium alloy enclosure 镁合金 Engineer standard 工标 Document center (database center)资料中心 Design Center 设计中心 Painting 烤漆(厂) Assembly组装(厂) Stamping 冲压(厂) Education and Training教育训练 proposal improvement/creative suggestion提案改善 Technological exchange and study 技术交流研习会 Technology and Development Committee 技术发展委员会 BS Brain Storming 脑力激荡 QCC Quality Control Circle 质量圈 PDCA Plan Do Check Action 计划执行检查总结 DCC delivery control center 交货管制中心 3C Computer 计算机类产品 Consumer electronics 消费性电子产品 Communication 通讯类产品 Core value(核心价值) Love 爱心