Attachment 14 Intershield 300 TDS
A light coloured, abrasion resistant, aluminium pure epoxy coating giving excellent long term anticorrosive protection and low temperature application capability.
PRODUCT DESCRIPTION A universal primer which can be applied directly to mechanically prepared shop primer or suitably prepared bare steel. Suitable for use with controlled cathodic protection.For use at Newbuilding or Maintenance & Repair.
INTENDED USES
ENA300-Bronze, ENA301-Aluminium 60% ±2% (ISO 3233:1998)
125 microns dry (208 microns wet). Range 100 - 200 microns dry (167 - 333 microns wet) may be specified depending upon end use.4.8 m2/litre at 125 microns dft, allow appropriate loss factors Airless Spray, Brush, Roller
PRODUCT INFORMATION Volume Solids Typical Film Thickness Theoretical Coverage Method of Application Finish/Sheen Not applicable Part B (Curing Agent)ENA303
Mix Ratio
2.50 volume(s) Part A to 1 volume(s) Part B
Flash Point (Typical)Part A 28°C; Part B 26°C; Mixed 28°C Induction Period
Not required
Overcoating Data - see limitations
Substrate Temperature
Colour Drying Information -5°C 5°C 25°C 35°C See Limitations section when Intershield 300 is used as part of an Intersleek scheme.
Note
Touch Dry [ISO 9117/3:2010]7 hrs 5 hrs 3 hrs 2 hrs Hard Dry [ISO 9117-1:2009]10 hrs 8 hrs 6 hrs 3 hrs Pot Life 6 hrs
6 hrs
150 mins
60 mins
Overcoated By -5°C
5°C
25°C
35°C
Min Max Min Max Min Max Min Max When overcoating with Intersleek 386, refer to the Intersleek 737 data.
Intershield 300 may be overcoated with Intersleek 737 at 0°C, the minimum interval being 12 hours and the maximum 30 hours.Intershield 300 may be overcoated with Intersleek 731 above 15°C. At 15°C, the minimum interval being 5 hours and the maxim being 2 days. For application below 15°C consult International Paint.
When overcoating with Interbond 201 or Interbond 501, refer to the Intergard 740 data.
Interthane 990 may be used on boottop areas at reduced overcoating intervals. Consult International Paint.Interfine 691 is currently only available in Europe.
When overcoating with Interfine 878, refer to the Interfine 979 data.
Note
Interfine 691 10 hrs 3 days 8 hrs 3 days 6 hrs 3 days 3 hrs 3 days Interfine 979 - -8 hrs 7 days 6 hrs 7 days 3 hrs 7 days Intergard 263 14 hrs 14 days 9 hrs 14 days 7 hrs 14 days 4 hrs 14 days Intergard 269 14 hrs 6 mths 9 hrs 6 mths 7 hrs 6 mths 4 hrs 3 mths Intergard 282 14 hrs 14 days 9 hrs 14 days 7 hrs 14 days 4 hrs 14 days Intergard 740 14 hrs 14 days 9 hrs 14 days 7 hrs 14 days 4 hrs 14 days Intershield 300Immersed Areas 14 hrs 14 days 9 hrs 14 days 7 hrs 14 days 4 hrs 14 days Intershield 300
Non Immersed Areas 14 hrs 6 mths 9 hrs 6 mths 7 hrs 6 mths 4 hrs 3 mths Intersleek 717 - -9 hrs 14 days 7 hrs 14 days 4 hrs 14 days Intersleek 731 - - - - 4 hrs 2 days 3 hrs 2 days Intersleek 737 - -7 hrs 24 hrs 5 hrs 2 days 3 hrs 2 days Interthane 990 14 hrs
5 days
9 hrs
5 days
7 hrs
3 days
4 hrs
2 days
REGULATORY DATA VOC
Note: VOC values are typical and are provided for guidance purposes only. These may be subject to variation depending on factors such as differences in colour and normal manufacturing tolerances.
386 g/lt as supplied (EPA Method 24)
318 g/kg of liquid paint as supplied. EU Solvent Emissions Directive (Council Directive 1999/13/EC)
Intershield 300
Abrasion Resistant Aluminium Pure Epoxy
When used as part of an approved scheme, this product has the following certification:
? Food Contact - Carriage of Grain (NOHA)
? Tank Coatings - B1 Classification of Ballast Tank Coatings (DNV/Marintek tested)? Tank Coatings - NORSOK M-501, Rev 3, system 7 (Marintek)? Fire Resistance - Smoke & Toxicity (Exova Warringtonfire)
? Fire Resistance - Surface Spread of Flame (Exova Warringtonfire)? Fire Resistance - Marine Equipment Directive compliant ? Food Contact - FDA Compliant: Dry Foodstuffs
? Potable Water - Carriage of Potable Water (TUV, Singapore) (BS6920:2000)
Potable Water Certification issued by external bodies is dependent upon formulation and/or manufacturing site. Based on this, products supplied in different territories may not be approved to all of the standards listed above.
Consult your International Paint representative for details.
CERTIFICATION
Consult your International Paint representative for the system best suited for the surfaces to be protected.When using in cargo holds, consult the Intershield 300 Cargo Hold Application Guidelines.
SYSTEMS AND COMPATIBILITY
Use in accordance with the standard Worldwide Marine Specifications.All surfaces to be coated should be clean, dry and free from contamination.
High pressure fresh water wash or fresh water wash, as appropriate, and remove all oil or grease, soluble contaminants and other foreign matter in accordance with SSPC-SP1 solvent cleaning.
SURFACE PREPARATIONS
NEWBUILDING
Where necessary, remove weld spatter and smooth weld seams and sharp edges.
Weld seams and areas of shop primer damage or breakdown should be blast cleaned to Sa2? (ISO 8501-1:2007) or power tooled to Pt3 (JSRA SPSS:1984).
Intact, approved, shop primers must be clean, dry and free from soluble salts and any other surface contaminants.Unapproved shop primers will require complete removal by blast cleaning to Sa2? (ISO 8501-1:2007). In some cases sweep blasting to a defined International Paint standard (eg AS2 or AS3) may be acceptable. Consult your International Paint representative for specific recommendations.
MAJOR REFURBISHMENT
Abrasive blast clean to minimum Sa2 (ISO 8501-1:2007) or International Paint Hydroblasting Standard HB2M. If oxidation has occurred between blasting and application of Intershield 300, the surface should be reblasted to the specified visual standard.
Surface defects revealed by the blast cleaning process, should be ground, filled, or treated in the appropriate manner.
REPAIR
Consult International Paint.
OTHER
For tank coating and application of Intersleek systems, consult International Paint for the detailed coating procedures that should be followed.
Consult your International Paint representative for specific recommendations.
NOTE
For use in Marine situations in North America, the following surface preparation standards can be used:SSPC-SP10 in place of Sa2? (ISO 8501-1:2007)SSPC-SP6 in place of Sa2 (ISO 8501-1:2007)SSPC-SP11 in place of Pt3 (JSRA SPSS:1984)
Material is supplied in two containers as a unit. Always mix a complete unit in the proportions supplied. Once the unit has been mixed it must be used within the working pot life specified.(1) Agitate Base (Part A) with a power agitator.
(2) Combine entire contents of Curing Agent (Part B) with Base (Part A) and mix thoroughly with power agitator.Application by brush is recommended for small areas only. Multiple coats may be required to achieve specified film thickness.
Application by roller is recommended for small areas only. Multiple coats will be required to achieve specified film thickness.
International GTA220. DO NOT thin more than allowed by local environmental legislation.International GTA822/GTA220
In the event welding or flame cutting is performed on metal coated with this product, dust and fumes will be emitted which will require the use of appropriate personal protective equipment and adequate local exhaust ventilation. In North America do so in accordance with instruction in ANSI/ASC Z49.1 "Safety in Welding and Cutting."
Recommended
Tip Range 0.66-0.79 mm (26-31 thou)
Total output fluid pressure at spray tip not less than 211 kg/cm2 (3000 p.s.i.)
APPLICATION Mixing
Airless Spray
Brush Roller Thinner Cleaner
Welding
Work Stoppages and Cleanup Do not allow material to remain in hoses, gun or spray equipment. Thoroughly flush all equipment with
International GTA822/GTA220. Once units of paint have been mixed they should not be resealed and it is advised that after prolonged stoppages work recommences with freshly mixed units.
Clean all equipment immediately after use with International GTA822/GTA220. It is good working practice to periodically flush out spray equipment during the course of the working day. Frequency of cleaning will depend upon amount sprayed, temperature and elapsed time, including any delays. Do not exceed pot life limitations.All surplus materials and empty containers should be disposed of in accordance with appropriate regional regulations/legislation.
All work involving the application and use of this product should be performed in compliance with all relevant national Health, Safety & Environmental standards and regulations.
Prior to use, obtain, consult and follow the Material Safety Data Sheet for this product concerning health and safety information. Read and follow all precautionary notices on the Material Safety Data Sheet and container labels. If you do not fully understand these warnings and instructions or if you can not strictly comply with them, do not use this product. Proper ventilation and protective measures must be provided during application and drying to keep solvent vapour concentrations within safe limits and to protect against toxic or oxygen deficient hazards. Take precautions to avoid skin and eye contact (ie. gloves, goggles, face masks, barrier creams etc.) Actual safety measures are dependant on application methods and work environment.
EMERGENCY CONTACT NUMBERS:
USA/Canada - Medical Advisory Number 1-800-854-6813
Europe - Contact (44) 191 4696111. For advice to Doctors & Hospitals only contact (44) 207 6359191China – Contact (86) 532 83889090R.O.W. - Contact Regional Office
SAFETY
Intershield 300 should be high pressure fresh water washed and/or solvent washed prior to overcoating, where
necessary, to ensure removal of any surface contamination that has accumulated.
Suitable for use on tanker decks subject to Classification Society Regulations.
Intershield 300 may be applied at substrate temperatures down to -15°C. Before applications are made below -5°C
consult your local IP representative for further detail of application procedure.
When Intershield 300 is to be overcoated with Intersleek 737, Intersleek 386 or Intersleek 731 the following
maximum pot lives must be observed:
+ 0°C - 160 minutes
+15°C - 105 minutes
+25°C - 75 minutes
+35°C - 45 minutes
Overcoating information is given for guidance only and is subject to regional variation depending upon local climate
and environmental conditions. Consult your local International Paint representative for specific recommendations.
Apply in good weather. Temperature of the surface to be coated must be at least 3°C above the dew point. For
optimum application properties bring the material to 21-27°C, unless specifically instructed otherwise, prior to mixing
and application. Unmixed material (in closed containers) should be maintained in protected storage in accordance
with information given in the STORAGE Section of this data sheet. Technical and application data herein is for the
purpose of establishing a general guideline of the coating application procedures. Test performance results were
obtained in a controlled laboratory environment and International Paint makes no claim that the exhibited published
test results, or any other tests, accurately represent results found in all field environments. As application,
environmental and design factors can vary significantly, due care should be exercised in the selection, verification of
performance and use of the coating.
LIMITATIONS
UNIT SIZE Unit Size Part A Part B
Vol Pack Vol Pack
For availability of other unit sizes consult International Paint
17.5 lt12.5 lt20 lt 5 lt 5 lt
UNIT SHIPPING WEIGHT (TYPICAL)Unit Size Unit Weight 17.5 lt23.4 Kg
Consult International Paint.
WORLDWIDE AVAILABILITY
The information in this data sheet is not intended to be exhaustive; any person using the product for any purpose other than that specifically
recommended in this data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at
their own risk. All advice given or statements made about the product (whether in this data sheet or otherwise) is correct to the best of our knowledge but
we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless
we specifically agree in writing to do so, we do not accept any liability at all for the performance of the product or for (subject to the maximum extent
permitted by law) any loss or damage arising out of the use of the product. We hereby disclaim any warranties or representations, express or implied, by
operation of law or otherwise, including, without limitation, any implied warranty of merchantability or fitness for a particular purpose. All products supplied
and technical advice given are subject to our Conditions of Sale. You should request a copy of this document and review it carefully. The information
contained in this data sheet is liable to modification from time to time in the light of experience and our policy of continuous development. It is the user's
responsibility to check with their local representative that this data sheet is current prior to using the product.
This Technical Data Sheet is available on our website at https://www.sodocs.net/doc/3c14550138.html, or https://www.sodocs.net/doc/3c14550138.html,, and should be the same as this
document. Should there be any discrepancies between this document and the version of the Technical Data Sheet that appears on the website, then the
version on the website will take precedence.
IMPORTANT NOTE
All trademarks mentioned in this publication are owned by, or licensed to, the AkzoNobel group of companies.
? AkzoNobel, 2014
https://www.sodocs.net/doc/3c14550138.html,