搜档网
当前位置:搜档网 › 机械词汇-很全

机械词汇-很全

机械词汇-很全
机械词汇-很全

机械词汇

Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld承插焊接

fillet weld角焊,填角焊branch connection分支接续fabrication tolerance.制造容差local heat treatment 局部热处理threaded pipe螺纹管seal welding.密封焊接

flange joint 凸缘接头undercut 底切

feeder馈电线conduit outlet电线引出口

seal fitting 密封接头, 密封配件Screw thread lubricant螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强

lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple螺纹接头zinc plated.镀锌的

ring joint 环接, 围缘接合bolt 螺栓control: 控制器National Electrical Code 全国电气规程job site 施工现场

master schedule 主要图表, 综合图表, 设计任务书, 主要作业表

torque wrench 转矩扳手Hard hat:安全帽

flange connection.凸缘联接stockpile贮存

Goggles:护目镜packing list装箱单

crate: 柳条箱purchased material list原材料进货单back-feed反馈wire coil线盘,线卷,

NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫

terminal block线弧, 接头排接线盒, 接线板, 线夹

power drill机械钻connector. 接线器

insulated sleeve绝缘套管wire connector接线器

wire terminal电线接头control wiring控制线路

motor lead电动机引出线power wiring电力布线

tender document.提供证件orifice plate.挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀piping system.管道系统reinforcement of weld加强焊缝fabrication.制造

dye penetrant examination染料渗透试验法

magnetic particle examination 磁粉检验butt weld 对接焊缝

girth weld环形焊缝cement lined piping 水泥衬里

weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试assembly.装配

Random Radiography随机射线照相检查

radiographic examination 射线照相检查 examination试验

erection 架设 arc welding 电弧焊

cable tray.电缆盘rigid steel conduit 钢制电线管

power control 功率控制 normal bend 法向[法线]弯管control cable控制电缆操纵索grounding conductor 接地导体cable glands: 电缆衬垫exfoliation剥落

power receptacle 电力插座junction box 分线箱

lighting fixture照明器材Circuit breaker断路开关

race way 电缆管道terminal box接线盒

distribution board配电盘, 配电屏receptacle 插座

tumble switch.翻转开关,拨动式开关amplifier panel 放大器盘

cathodic protection system 阴极保护系统control console 控制台

electrical material电气材料convenience receptacle.电源插座cable gland 电缆衬垫filler rod焊条shield gas 保护气体

TIG: Tungsten-arc Inert-Gas welding 钨极电弧惰性气体保护焊

tensile strength 抗张强度shield jig保护夹具

high frequency generator.高频发电机welding rod 焊条

filler metal 焊料, 焊丝shop fabrication 车间制造

field installation 现场安装welding bead 焊道

both sides welding.双面焊接residual stress 残余应力electrode 电焊条condensation 冷凝longitudinal.纵向的horizontal line 水平线circumferential joint 周圈接缝nondestructive examination.非破坏性检验, qualification: 合格性construction work施工工程welded joint焊接缝焊接节点gas cutting.气割arc cutting电弧切割grind off 磨掉

metallic luster 金属光泽Screwed Piping Joints螺丝状的管接头gouging .刨削槽Bending: 挠曲witness test订货人在场的试验Welding: 焊接Threading: 车缧纹Leveling:校平color identification 彩色识别Alignment:对准,定位调整check against 检查, 核对Fixing:固定Console:控制台cubicle室,箱audit 审计material certificate.材料合格证vertical panel竖直面板power distribution panel 配电盘gauge board仪表板beveling 磨斜棱,磨斜边local panel 现场配电盘grouting 灌浆fabrication 加工,制造instrument rack 计测器支架tank gauge 液面计flushing 冲洗,填缝analyzer分析器

piping管道敷设tubing敷设管道cable fitting电缆配件elbow.弯管接头main pipe 主管道bend.弯管弯头

solvent 溶剂postweld heat treatment 焊后热处理jig.夹具

arc gouging 电弧刨削 chipping修琢machining 机械加工bridges.管式桥clamp.夹钳tack welding 点焊

butt welding 对接焊grinder. 磨床commencement.开始gusset plate角撑板, 加固板process pipe 工艺管道land 纹间表面

tee 三通管丁字钢 T形梁opening 开口reinforcing pad.补强垫,增强衬板flux 焊剂wet developer 湿显像剂blowhole气泡,气孔inclusion 杂质imperfection 缺陷limitation 限度valve 阀,闸门structural attachment 结构附件tapered allowance 削尖余量

tack welding 平头焊接sputter 喷溅scale 废料

lateral translation侧向平移weld joint 焊缝, 焊接接头plug.塞

fusion 熔融base material基底材料lead foil 铅箔intensifying screen 增光屏, 光增强屏pressure test.压力试验film density.影片密度line number行数 leak test漏泄试验

plate thickness 筛板厚度restoration修理

field fabricated 工地制造的,现场装配的junction box.接线盒

flow sheet 流程图vent 放气孔, 通风孔drain 排水管

机械专业英语词汇(很全)

金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic

误差 error 响应 response 定位 allocation 机床夹具 jig

动力学 dynamic 运动学 kinematic 静力学 static 拉伸 pulling

分析力学 analyse mechanics 压缩 hitting 剪切 shear

扭转 twist 弯曲应力 bending stress 强度 intensity

三相交流电 three-phase AC 磁路 magnetic circles

变压器 transformer 异步电动机 asynchronous motor 几何形状 geometrical

精度 precision 正弦形的 sinusoid 交流电路 AC circuit

机械加工余量 machining allowance 变形力 deforming force 退火 anneal

变形 deformation 应力 stress 硬度 rigidity 热处理 heat treatment

正火 normalizing 脱碳 decarburization 渗碳 carburization 电路 circuit 半导体元件 semiconductor element 反馈 feedback 发生器 generator

直流电源 DC electrical source 门电路 gate circuit 逻辑代数 logic algebra

外圆磨削 external grinding 内圆磨削 internal grinding 绞孔 fraising

平面磨削 plane grinding 变速箱 gearbox 离合器 clutch

绞刀 reamer 螺纹加工 thread processing 螺钉 screw 铣削 mill

铣刀 milling cutter 功率 power 工件 workpiece 齿轮加工 gear mechining

齿轮 gear 主运动 main movement 主运动方向 direction of main movement

进给方向 direction of feed 进给运动 feed movement

合成进给运动 resultant movement of feed 前刀面 rake face

合成切削运动 resultant movement of cutting 刀尖 nose of tool

合成切削运动方向 direction of resultant movement of cutting 前角 rake angle

切削深度 cutting depth

机械专业词汇:

hardenability 淬透性carbide tool 硬质合金刀具alloy tool steel 合金工具钢alloyed cast iron 合金铸铁carbon steel 碳素钢carbon tool steel 碳素工具钢cast iron 铸铁cast steel 铸钢die material 模具材料

high alloy steel 高合金钢high carbon steel 高碳钢low alloy steel 低合金钢low carbon steel 低碳钢shock resistant tool steel 抗冲击工具钢

nodular graphite iron 球墨铸铁malleable cast iron 可锻铸铁

mottled cast iron 麻口铸铁hardenability curve 淬透性曲线

hardening capacity 淬硬性(硬化能力)hardness penetration diagram “U”形曲线hardness profile 硬度分布(硬度梯度)heat treatment procedure 热处理规范

heat treatment installation 热处理设备 heat treatment furnace 热处理炉

heat treatment cycle 热处理工艺周期heat time 加热时间

heat system 加热系统heating up time 升温时间heating curve 加热曲线

high temperature carburizing 高温渗碳high temperature tempering 高温回火isothermal annealing 等温退火interrupted ageing treatment 分级时效处理local heat treatment 局部热处理overheated structure 过热组织

pack carburizing 固体渗碳Oxynitrocarburizing 氧氮碳共渗

partial annealing 不完全退火recrystallization temperature 再结晶温度

cutting part 切削部分tool angle 刀具角度tool back angle 背前角

tool back clearance 背后角tool backlash movement (tool retracting) 退刀

tool back wedge angle 背楔角tool base clearance 基后角

tool cutting edge plane 切削平面tool cutting edge angle 主偏角

tool grinding machine 工具磨床tool geometrical rake 几何前角

tool nomal clearance(rake) 法后角(法前角)locating device 定位装置

tool orthogonal clearance(rake, wedge) 后角(前角,楔角)

locating face 定位面locating pin 定位销(挡料销)locating plate 定位板

locating ring 定位圈locating rule 定位尺locating element 定位零件(定位要素)work hardening 加工硬化internal cylindrical grinding machine 内圆磨床

internal cylindrical turing 内圆车削internal force 内力

internal cylindrical grinding machine with vertica 立式内圆磨床

hole scraping (turning,milling, lapping) 刮孔(车孔,铣孔,研孔)

hole grinding (slotting,honing, flanging) 磨孔(插孔,珩孔,翻孔)

versatile grinding machine 多用磨床versatile lathe 多用车床

vertical multi-tool lathe 立式多刀车床precision milling machine 精密铣床

spot face 孔口平面drill and countersink 定心钻,中心钻counterbore cutter head 扩孔钻头jig boring machine 坐标镗床

jig grinding machine 坐标磨床jig and fixture 夹具

fixture of gear cutting machine 齿轮加工机床夹具

fixture of milling machine 铣床夹具fixture of grinding machine 磨床夹具fixture of planing machine 刨床夹具fixture of slotting machine 插床夹具vacuum fixture 真空夹具universal fixture (jig) 通用夹具stationary fixture 固定夹具standard fixture (jig) 标准夹具pneumatic fixture (jig) 气动夹具open-side boring and milling machine 悬臂镗铣床magnetic fixture (jig) 磁力夹具locating device (face,element) 定位装置(面,元素)hydraulic fixture (jig) 液压夹具slide gauge 游标卡尺triple action press 三动压力机tow point single action press 双点单动压力机watch press 台式压力机

closed type single action crank press 闭式单动(曲柄)压力机

one point single action press 单点单动压力机

open-back inclinable press 开式双柱可倾压力机

four crank press 四曲柄压力机

stright side single action double crank press 闭式双点单动双曲柄压力机

single piece frame press 整体框架式压力机

rocker arm type press 摇臂式压力机

top drive sheet metal stamping automatic press 上传动板料冲压自动压力机

barrel surface 圆柱形表面antiflowback valve 反流阀

reciprocating-screw machine 往复螺旋注塑机single-stage plunger 单级柱塞

shot chamber 注射室curing temperature 固化温度shot capacity 注射能力

plunger diameter 柱塞直径sectional area of plunger 柱塞面积

hydraulic cylinder 液压缸blanking die 冲裁模

blanking clearance, die clearance 冲裁间隙blanking force 冲裁力

die,stamping and punching die 冲模tonnage of press 压力机吨位shut height of press machine 压力机闭合高度center of die, center of load 压力中心clearance between punch and die 凹凸模间隙tolerance of fit 配合公差shearing force diagram 剪力图peak die load 模具最大负荷clamping force (element, device, piston) 夹紧力(件,装置,活塞)

clamp plate (ring) 压板(夹紧环)shearing force (plane) 剪切力(平面)side clearance angle 侧隙角side locating face 侧定位面

side-push plate 侧压板shuttle table 移动工作台matrix plate 凹模固定板material removal rate 材料切除率sheet matal 板料blanking die 冲裁模assembling die 复合冲模,装配用模具compound blank and pierce dies 落料冲孔模shaving die 切边模,修边模shankless die 无柄模具

scrapless progressive die 无废料连续模return-blank type blanking die 顶出式落料模expanding die 胀形模,扩管模die for special purpose 专用模

cavity plate (block) 凹模bend ability 可弯性bend arc 弯曲弧

bending angle (line) 弯曲角(线)bending brake (bending machine) 弯板机,拆弯机bending fatigue 弯曲疲劳bending radius 弯曲半径

minimum bending radius 最小弯曲半径bending operation 弯曲工序

air-bend die 自由弯曲模bending moment diagram 弯矩图

blank length of bend 弯曲件展开长度

relative bending radius 相对弯曲半径bending equipment for plastics 塑料折弯设备drawing machine 拉拔机drawing numbers 拉伸次数

drawing ratio (coefficient,force,speed) 拉伸比(系数,力,速度)

foamed (cellular) plastic 泡沫塑料Thermoplastic 热塑性塑料

plastic industry 塑料(工业)行业blow molding die for plastics 塑料吹模机standard die components for plastics 塑料模具标准化零部件

thermoforming machine for plastics 塑料热成型机transfer mold 传递模

foaming mold for plastics 泡沫塑料模型laminating machine 层压机

plastic molding press 塑料制品成型压力机parting surface 分型面

other plastics converting machine 其它塑料加工机械Draft 脱模斜度compression molding machine 压塑机transfer mold 压注模(也称传递模)extruder double-screw for plastics 塑料加工用双螺杆挤压机ring gate 环形浇口extruder single-screw for plastics 塑料加工用单螺杆挤压机spreader 分流锥ash-type mold 溢出式压缩模portable transfer mold 移动式压注模

mold for plastics 塑料成型模具(简称塑料模)fixed transfer mold 固定式传递模

mold for thermoplastics 热塑性塑料模edge gate 侧浇口

injection mold for thermoplastics 热塑性塑料注射模runner plate 流道板

portable transfer mold 移动式传递模insulated runner mold 绝热流道模

warm runner mold 温流道模pin-point gate 点浇口

submarine gate, tunnel gate 潜伏浇口warm runner plate 温流道板

stationary mold, fixed half, fixed die, cover die 定模

moving die, movable mold, moving half 动模sprue gating 中心浇口,浇道浇口

die-casting die 压力铸造模具(简称压铸模)fixed clamping plate 定模底板moving clamping plate 动模底板support plate, backing plate 支承板

movable core 活动型芯baffle 导流块sprue spreader 分流锥(分流器)ejector pin (plate) 推杆(板)ejector pin retaining plate 推杆固定板gate 内浇口air vent 排气槽parting line 分型面feed (gating, runner) system 浇注系统pouring temperature (rate, time) 浇注温度(速度,时间)

sprue base (bush, gate, puller) 直浇道窝(浇口套,直接浇口,拉料杆)

final forging temperature 终锻温度finishing temperature 终锻温度initial forging temperature 始锻温度flat die hammer 自由锻锤forge furnace 锻炉forge ratio (forge reduction) 锻造比

forging crankpress 锻造用曲柄压力机

forging die (die steel, drawing) 锻模(锻模钢,锻件图)

forging line (load, practice) 锻造生产线(负荷,工艺)

forging plane (plant) 锻造面(厂)

forging pressure (process, range) 锻造力(工艺,范围)

hammer forging die 锤锻模forging heat-treatment 锻件热处理forging temperature interval 锻造温度范围forging tolerance 锻件公差

hot forging drawing 热锻件图chip formation 成型切削

chip load (force) 切削力drilling and reaming 钻孔和铰孔

taper turning 锥度车削external threading 外螺纹车削

chuck handle 夹头扳手,夹头钥匙combination chuck 复动夹头

shaper and planer 牛头刨床和龙门刨床slotting machine 插床

rotary-type bushing 旋转衬(钻)套underlying metal 底层金属

perforated electrode 多孔电极electro-chemical machining 电化学加工form electromachining 电加工成形面electric machining 电加工

salt bath electrode furnace 电极盐浴炉electrolytic forming machine 电解成形机electrochemical machining 电解加工electrochemical machining tool 电解加工机床electrolytic universal tool and cutter grinder 电解万能工具磨床

electrolytic heat treatment 电解液热处理

electrohydraulic forming 电液成形electrolytic marking machine 电解刻印机electrolytic surface grinder 电解平面磨spark erosion machining 电火花加工法electrical discharge machining (EDM) 电火花加工

electrodischarge cutting machine 电火花切割机

electrical discharge machine 电火花加工机床

electrical spark-erosion perforation 电火花打孔electrode contact surface 电极接触面electrical discharge forming 电火花成形机laser cutting machine 激光切割机electron beam cutting machine 电子束切割机

cavity sinking EDM machines 型腔电火花加工机床

travelling-wire EDM machine 线电极电火花加工机床

electro-discharge machine tool 电火花加工机床

electron beam machining (EBM) 电子束加工

electron beam machine tool 电子束加工机床form electromachining 电加工成形面tiny hole spark-erosion grinding machine 电火花小孔磨床

spark-erosion cutting with a wire 电火花线切割

wire cut electric discharge machine 电火花线切割机

encoded transducer 编码传感器compensator 补偿器

incremental measuring system 增量测量系统analog control 模拟控制

assembly language 汇编语言data processing system 数据处理系统

graphic data processing 图形处理linear (circle) interpolator 线形(圆形)插补器

DNC--direct numerical control 直接数字控制 a safety loop 保险圈

CNC--computer numerical control 计算机数字控制 a wire loop 钢丝圈

DPU--Data Processing Unit 数控处理单元DLU--Data Loops Unit 数据循环单元cutter saddle 刀架cylinder saddle 鞍形气缸座loop a line 环路法连接线路horizontal spindle 轴式vertical spindle 立轴式travelling-column 行程立柱feedback unit 反馈单元machining center 加工中心tool-storage 刀具存贮

ball screw 滚珠丝杠tool changer 刀库machine control unit (MCU) 机床控制单元flexible machining system 柔性制造系统disk operating system (DOS) 磁盘操作系统Microsoft dish operating ssytem (MS-DOS) 微软磁盘操作系统

program and data files 程序和数据文件

internal and external command 内部和外部文件

format a diskette 磁盘格式化diskcopy command 磁盘拷贝命令

erase (deletion) command 删除命令

create (change, remove) directory 建立(改变,移动)目录

hard disk drive (HDD) 硬盘驱动器hard (soft) disk 硬(软)盘

standard keyboard 标准键盘color display 彩色显示

printer operating procedures 打印机操作程序application window 应用程序窗口

batch file 批处理文件control (main,system) menu 控制(主,系统)菜单configuration system file 系统配置文件

FMS (flexible manufacturing system) 柔性制造系统

CNC (computer numerical control) 计算机数字控制

revised feed signal 反进给信号default selection mode 默认选择模式

MCU (machine control unit) 控制加工单元

ACS (adaptive control system) 自动补偿系统CRT (cathode-ray tube) 显像管

process planning 制定工艺过程

CIM (computer integrated manufacturing) 计算机集成制造

vertical stroke 垂直行程system variable 系统变量

accurate die casting 精密压铸air bend die 悬空弯曲模具

blank through dies 漏件式下了模calendering 压延成形

center gated mold 中心浇口式模具cold chamber die casting 冷室压铸compacting molding 粉末压出成形double stack mold 双层模具

duplicated cavity plate 复板模encapsulation molding 注入成形expander die 扩径模family mold 成套制品模具fantail die 扇尾形模具

fantail die 鱼尾形模具f;ash mold 溢料式模具flash mold 溢料式模具

flange bending die 弯缘模具flang trim die 整缘磨具

flash trimming die 整缘磨具flat edge teim die 水平整缘磨具

foam frming 发泡成形gang die 成排模具gravity casting 重力铸造

sand mold casting 砂模铸造sectional die 对合模具shaper 定型模具

singe cavity mold 单腔模具squeeze casting die 高压铸造

squeezing casting die 挤压模swaging 挤锻tandem die 串列模具

shree plates mold 三板式模具transfer molding 传送成形universal mold 通用模具warn foring 温锻air vent valve 通气阀

anchir pin 锚梢angular cams 角凸轮angular pin 交梢(倾斜梢)

baffle 调节阻板baffle plate 折流档板ball button 球塞套

ball plunger 定位球塞binder plate 压板ball silder 球塞滑块

binder plate 压板blank holder 防皱压板blanking punch 下料冲头

bottom board 浇注底板 bottom plate 下固定板bracket 托架

casting ladle 浇注包casting lug 铸耳cavity 模穴(模仁/模腔)

cavity adaptor plate 固定侧安装板cavityplate 模仁板 cavity retainer plate 模穴托板clamping block 锁定块cooling manifold 冷却歧管

core adaptor plate 可动侧安装板core plate 心型板

core push back spring 心型回位弹簧diaphragm gate 盘形浇口

die approach 模头料道die clamper 夹模器die fastener 模具固定用零件

die plate 冲模板direct gate 直接浇口draft 拔模锥度

draw bead 张力调整杆drive bearing 传动轴承ejector pad 顶出垫

ejector plate 顶出板ejector valve 顶出阀calendaring molding 压延成形powder metal forging 粉末锻造rotary forging 回转锻造rotational molding 离心成形 shell casting 壳模铸造foam forming 发泡成形

hot chamber die casting 热室压铸 warm forging 温锻 investment casting 精密铸造

matched die method 对模成形法laminating method 被覆淋膜成形

low pressure casting 低压铸造lost wax casting 脱腊铸造matched mould thermal forming 对模热成形模landed plunger mold 有肩柱塞式模具landed positive mold 有肩全压式模具loading shoe mold 料套式模具

center-gated mold 中心浇口式模具loose detail mold 活零件模具

manifold die 分歧管模具modular mold 组合式模具

multi-cavity mold 多模穴模具multi-gate mold 复式浇口模具palletizing die 叠层模plaster mold 石膏模fishtail die 鱼尾形模具protable mold 手提式模具lancing die 切口模 raising(embossing) 压花起伏成形

re-entrant mold 倒角式模具single cavity mold 单腔模具

three plates mold 三片式模具air vent vale 通气阀anchor pin 锚梢

ball slider 球塞滑块cooling spiral 螺旋冷却栓ejection pad 顶出衬垫ejector leader busher 顶出导梢衬套film gate 薄膜形浇口finish machined plate 角形模板finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销

flash gate 毛边形浇口flask 上箱floating punch 浮动冲头

gate land 浇口面guide plate 导板guide rail 导轨head punch 顶镦冲头headless punch 直柄沖头heavily tapered solid 整体模蕊盒impact damper 缓冲器injection ram 压射柱塞inlay busher 嵌入衬套knockout bar 脱模杵land 合模平坦面land area 合模面

locating center punch 定位中心冲头locating pilot pin 定位导梢

locking plate 定位板making die 打印冲子manifold block 歧管档块

master plate 靠模样板match plate 分型板 mold base 塑胶模座

mold clamp 铸模紧固夹mold platen 模用板moving bolster plate 可动侧模板

one piece casting 整体铸件parallel block 平行垫块paring line 分模线

parting lock set 合模定位器pass guide 穴型导板peened head punch 镶入式冲头pin gate 针尖浇口plate 衬板rack 机架rapping rod 起模杆retainer pin 嵌件梢retainer plate 托料板slag riser 冒渣口

spacer block 间隔块spacer ring 间隔环square key 方键

square nut 方螺帽square thread 方螺纹stop collar 限位套

straight pin 圆柱销stripper plate 剥料板submarine gate 潜入式浇口support pillar 支撑支柱/頂出支柱supporting plate 扥板

tab gate 辅助浇口taper key 推拔键taper pin 拔锥梢/锥形梢three start screw 三条螺纹tie bar 拉杵tunnel gate 隧道形浇口wortle plate 拉丝模板3D coordinate measurement 三次元量床

boring machine 搪孔机cnc milling machine CNC铣床contouring machine 轮廓锯床copy grinding machine 仿形磨床copy lathe 仿形车床copy milling machine 仿形铣床copy shaping machine 仿形铇床cylindrical grinding machine 外圆磨床

die spotting machine 合模机drilling machine 钻孔机

engraving machine 雕刻机engraving E.D.M. 雕模放置加工机form grinding machine 成形磨床graphite machine 石墨加工机

horizontal boring machine 卧式搪孔机 horizontal machine center 臥式加工制造中心internal cylindrical machine 內圆磨床lap machine 研磨机

machine center 加工制造中心NC drilling machine NC钻床

NC grinding machine NC磨床NC lathe NC车床

NC programming system NC程式制作系统planer 龙门铇床

profile grinding machine 投影磨床radial drilling machine 旋臂钻床

surface grinder 平面磨床try machine 试模机turret lathe 转塔车床

universal tool grinding machine 万能工具磨床

vertical machine center 立式加工制造中心autocollimator 自动准直机

bench comparator 比长仪block gauge 块规calibration 校准

caliper gauge 卡规check gauge 校对规clearance gauge 间隙规comparator 比测仪cylinder square 圆筒直尺depth gauge 测深规

dial indicator 针盘指示表dial snap gauge 卡规digital micrometer 数位式测微计feeler gauge 测隙规gauge plate 量规定位板height gauge 测高规

inside calipers 內卡钳limit gauge 限规morse taper gauge 莫氏锥度量规optical flat 光学平晶optical parallel 光学平行passimeter 內径仪position scale 位置刻度 protractor 分角器radius 半径

ring gauge 环规sine bar 正弦量规snap gauge 卡模

square master 直角尺telescopic gauge 伸缩性量规 working gauge 工作量規aluminium alloy 铝合金钢bearing alloy 轴承合金clad sheet 被覆板ferrostatic pressure 钢铁水静压力galvanized steel sheet 镀锌铁板

hard alloy steel 超硬合金钢low alloy tool steel 特殊工具钢

low manganese casting steel 低锰铸钢marging steel 马式体高強度热处理钢martrix alloy 马特里斯合金meehanite cast iron 米汉纳铸钢meehanite metal 米汉纳铁merchant iron 市售钢材 prehardened steel 顶硬钢stainless steel 不銹钢tin plated steel sheet 镀锡铁板

vinyl tapped steel sheet 塑胶覆面钢板age hardening 時效硬化 ageing 老化处理

air hardening 气体硬化air patenting 空气韧化annealing 退火

anode effect 阳级效应anodizing 阳级氧化处理atomloy treatment 阿托木洛伊表面austempering 奧氏体等温淬火austenite 奧斯田体/奧氏体bainite 贝氏体banded structure 条纹状组织

barrel plating 滾镀barrel tumbling 滾筒打光blackening 染黑法

box annealing 箱型退火box carburizing 封箱渗碳bright electroplating 辉面电镀bright heat treatment 光辉热处理bypass heat treatment 旁路热处理

carbide 炭化物carburized case depth 浸碳硬化深层carburizing 渗碳chemical plating 化学电镀chemical vapor deposition 化学蒸镀coarsening 結晶粒粗大化coating 涂布被覆controlled atmosphere 大气热处理creeping discharge 蠕缓放电decarburization 脱碳处理

decarburizing 脱碳退火depth of hardening 硬化深层

diffusion annealing 扩散退火electrolytic hardening 电解淬火

first stage annealing 第一段退火flame hardening 火焰硬化

flame treatment 火焰处理full annealing 完全退火

gaseous cyaniding 气体氧化法globular cementite 球状炭化铁

grain size 結晶粒度granolite treatment 磷酸溶液热处理graphitizing 石墨退火hardening 硬化heat treatment 热处理

hot bath quenching 热浴淬火induction hardening 高周波硬化

ion carbonitriding 离子渗碳氮化ion carburizing 离子渗碳处理

ion plating 离子电镀low temperature annealing 低温退火malleablizing 可锻化退火martempering 麻回火处理

martensite 马氏体/硬化铁炭metallikon 金属噴镀法

metallizing 真空涂膜nitrocarburizing 软氮化normalizing 正常化overageing 过老化overheating 过热pearlite 针尖组织phosphating 磷酸盐皮膜处理physical vapor deposition 物理蒸镀plasma nitriding 离子氮化pre-annealing 预备退火precipitation 析出precipitation hardening 析出硬化process annealing 制程退火

quench ageing 淬火老化quench hardening 淬火quenching crack 淬火裂痕recrystallization 再结晶 residual stress 残留应力retained austenite 残留奧salt bath quenching 盐浴淬火sand blast 喷砂处理seasoning 時效处理second stage annealing 第二段退火secular distortion 经年变形segregation 偏析selective hardening 部分淬火shot blast 喷丸处理single stage nitriding 等温渗氮soaking 均热处理solution treatment 固溶化热处理stabilizing treatment 安定化处理straightening annealing 矫直退火strain ageing 应变老化

stress relieving annealing 应力消除退火subzero treatment 生冷处理

surface hardening 表面硬化处理tempering crack 回火裂痕

thermal refining 调质处理thermoechanical treatment 加工热处理transformation 变态under annealing 不完全退火

vacuum carbonitriding 真空渗碳氮化vacuum carburizing 真空渗碳处理

vacuum hardening 真空淬火vacuum heat treatment 真空热处理

vacuum nitriding 真空氮化water quenching 水淬火broing machine 搪孔机

CMC milling machine CMC铣床 wolfrtam (W) 钨vanadium (V) 钒

uranium (U) 铀titanium (Ti) 钛tkallium (Ti) 铊tantalum (Ta) 钽stannum (Sn) 锡scandium (Sc) 钪samarium (Sm) 钐

driling machine 钻孔机graphite mackine 石墨加工机praner 投影磨床

radial driling machine 旋臂钻床bench comparatcr 比长仪feeler guage 测隙规guage plate 量规定位板height guage 测高规morse taper guage 莫氏锥度量规nano 奈米(十亿分之一) plug guage 塞规thickness gauge 厚薄(测隙)规

low alloy tool steel 特殊工具钢maraging steel 马式体高强度热处理钢mateix alloy 马特里斯合金meehanite mttal 米汉纳铁perhardened steel 预硬钢ageing treatment 老化处理austepeering 奥氏体等温淬火bright heat treatement 光辉热处理bypass heat treament 旁路热处理

diffusion annealing 扩散退火acetylene 乙炔ampere 电流安培

angel welding 角焊arc 电弧argon arc welding 氩弧焊接

bare electrode 光熔焊接camber 电弧弯曲cascade 階叠熔接法

clad weld 被覆熔接crator 焊疤excess metal 多余金属

gas shield 气体遮蔽hand face shield 手握面罩hard facing 硬表面堆焊laser beam welding 雷射光焊接metal electrode insert gas welding MIG 熔接overlaying 堆焊propane gas cutting 丙烷气切割seam 焊缝

seaming 接合seam welding 流缝熔接series seam welding 串联缝熔接

spark 火花stud arc welding 电弧焊接underlaying 下部焊层

weld flow mark 焊接流痕weld mark 焊接痕weld penetration 熔接透入welding bead 焊接泡welding interval 焊接周期activator 活化剂adapter ring 接模环bag moulding 气胎施压成形bank 滞料

breathing 排气caulking compound 填隙料color masterbatch 色母料color matching 调色colorant 着色剂daylight 开隙elastomer 弹性体extruded bead sealing 压出粒涂层法floating platen 活动模板

foaming agent 发泡剂granule 颗粒料hot mark 热斑 hot stamping 烫印

kiss-roll coater 滚压涂布机kneader 混合机knife coating 刮刀涂布

levelling agent 匀涂剂lubricant 润滑剂mandrel 模心型

master batch 母料matrix 基料molecular 分子筛

mould clamping force 锁模力mould release agent 脱模剂over packing 过充填oxidation 氧化parison 吹气成形坯料pin point gate 针孔形浇口plasticizer 塑化剂plastomer 塑体plating 电镀ram 冲柱

ram extruder 活塞式押出机reciprocating screw 往复螺杆

restricted gate 限制形浇口sealer 封口机side gate 侧向浇口

slip agent 光滑剂snap fit 滑入配合spanishing 凹痕印刷

spray up 喷附成形staple fiber 短纤维strain 应变strand 丝束

stress cracking 应力龟裂take out device 取料装置toggle type mould clamping system 肘杆式锁模装置torpedo spreader 鱼雷形分流板transparency 透明性under coat 打底突层Steam trace 加热蒸汽管道branch connection 分支接续fabrication tolerance 制造容差threaded pipe 螺纹管seal welding 密封焊接flange joint 凸缘接头

seal fitting 密封接头, 密封配件Screw thread lubricant 螺纹润滑剂Seal 绝缘层lock washer 锁紧[止动, 防松]垫圈electrical panel 配电板,配电盘

zinc plated 镀锌的National Electrical Code 全国电气规程

master schedule 主要图表, 综合图表, 设计任务书, 主要作业表

flange connection 凸缘联接Hard hat 安全帽packing list 装箱单

crate 柳条箱purchased material list 原材料进货单back-feed 反馈

NPT thread 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧, 接头排接线盒, 接线板, 线夹insulated sleeve 绝缘套管wire terminal 电线接头motor lead 电动机引出线orifice plate 挡板flange gasket 法兰垫片dimensional inspection 尺寸检验ABS resin 丙烯轻丁二烯苯arcylic 压克力

acetal copolymer 共聚甲醛acetal resin 聚甲醛树脂 acetone resin 丙酮树脂

acrylic fiber 丙乙轻纤维acrylic resin 丙烯树脂

acrylonitrile-styrene 丙乙轻苯乙烯树脂additional polymer 加聚物

adhesive 粘着剂adhesive film 粘着薄膜 alkyd resin 醇酸树脂

allyl resin 烯丙醇酯树脂amino resin 氨基树脂butadiene 丁二烯

butyl acetate 醋酸丁酯carbon fiber 碳纤维catalyst 催化剂

cellulose acetate 醋酸纤维素(CA) cellulose acetate butyrate 醋酸丁酸纤维素

chlorinated polyethylene 氯化聚乙烯chopped strand 短玻璃丝束

crystalline polymer 结晶性聚合物cyclohexanone 环乙酮

cyclohexanol 环乙酯dially phthalate 苯二甲酸二烯丙酯

dibutyl fumarate 反丁烯二酸二丁酯dioctyl fumarate 反丁烯二酸二辛酯

engineering plastics 工程塑胶ethyl acetate 醋酸乙酯

ethylene vinylacetate 乙烯-醋酸乙烯共聚物expanded polystyrene 发泡聚苯乙烯fibrillation 原纤化filament 长纤维fluorocarbon resin 氟碳树脂

graphite fiber 石墨纤维high impact polystyrene 高冲击聚苯乙烯(HIPS)

high impact polystyene 高冲击产聚苯乙烯melamine resin 三聚氰胺酚醛树脂

mylar 聚乙烯对苯二酸oxirane 环氧乙烷plastic 塑料polyacetal 聚甲醛polyacetylene 聚乙炔polyacrylic acid 聚丙烯酸(PAP) polyalcohol 多元醇polyamide 耐龙(PA) polybutyleneterphthalate 聚对苯二甲酸丁酯

polycarbonate 聚碳酸酯polyethylenterephthalate 聚乙醇对苯(PETP) polymetylmethacrylate 聚甲基丙烯酸甲酯addendum of thread 螺牙冠

adjustable spaneer 活动扳手angle cutter 角铣刀approaching face 渐近面

arbor 心轴back clearance angle 背隙角back rake 背斜角

backing 视垫ball end mill 球端铣刀belt sander 带式打磨机bevel angle 去角bevel lead 倒角blade 刀刃blank 胚料bottoming hand tap 底螺丝攻brazed tool 硬锝刀具centering location 定心ceramic tool 陶瓷刀具chamfer 倒角chamfered corner 去角角隅chamfering machine 倒角机chamfering tool 去角刀具chaser 螺丝钣刀

chip breaker 断屑器clamp face 夹持面clearance angle 隙角

cold circular saw 常温圆规compass 两角规concave angle 凹角

concave cutter 凹面铣刀corner radius 角隅半径cotter diameter 梢径

crack 破裂crater 刀痕磨耗crest radius 牙顶圆角半径cutting edge angle 切深角cutting edge inclination 切刃斜角

cylinder key broach 键孔拉刀drawing thread 退刀螺蚊face milling cutter 面铣刀end cutting angle 副切深角end gash 刀端深口face 斜面f laking 破损

flank 隙面(刀腹)flank wear 隙面磨耗fluted land 槽背

gear hob 滚齿hatching 部面线helix angle 螺旋角

hexagon headed bolt 六角头螺栓hexagon nut 六角螺帽hook angle 勾角

included angle 刀刃角index head 分度头jack 千斤顶lapping 研磨lead 导程machinability 被切削性major cutting edge 主切刃

major flank 主隙面margin 刀缘metal saw 金工锯

metal slitting saw 锯割铣刀minor flank 副隙面no relief thread 无隙螺纹

normal clearance angle 法隙角normal rake 法斜角normal wedge angle 法刀口角nose angle 刀角nut tap 螺帽螺丝攻orthogonal clearance angle 垂直隙角orthogonal rake 正斜角orthogonal wedge angle 垂直刀口角

pearn tap 特殊螺丝攻plain milling cutter 平铣刀plain tapered bore 普通推拔孔plug hand tap 塞螺丝攻polot tap 导桿螺丝攻pull head 拉头

pulley tap 带轮螺丝攻radial 径向斜面radial thread relief 径向螺牙隙radius end mill 圆角端铣刀radius of circle 圆角rake angle 斜角

ratchet broach 刺轮拉刀retrieving head 支持头rifle broach 来福线拉刀

sand paper 砂纸scraper 刮刀segment angle 弧角

serration broach 细齿拉刀shank 刀柄side clearance angle 侧隙角side rake 侧斜角slab milling cutter 平板铣刀spade drills 铲钻

spanner 扳手spline broach 方栓槽拉刀square 直角尺

square end mill 方形端铣刀square sleeker 方形镘刀square trowel 直角度

straight bore 直孔straight flute 直尺槽straight shank drills 直柄钻头subland drills 多槽钻头super crest tap 高顶螺丝攻tap 螺丝攻

taper hand tap 斜螺丝攻taper shank 推拔柄taper tap 推拔螺丝攻

tapping torque 攻螺丝扭力target drills 留心钻thread 螺纹

thread milling cutter 螺纹铣刀threads per inch 牙数throw away tip 折叠式刀片throw away tool 折叠式刀具tool angles 刀具角

tool for lathe 车刀tool point angle 刀刃角tool reference plane 基准面

tosecan 画线盘waffle die flattening 压文效平working angles 切削刀barrelling 滚光加工blanking 下料加工cam die bending 凸轮弯曲加工

double shearing 叠板裁断drawing 引申加工drawing with ironing 抽引光滑加工fine blanking 精密下料加工finish blacking 光制下料加工flabging 凸缘加工impact extrusion 冲击挤压加工lock seaming 固定接合marking 刻印加工

parting 分段加工progressive blanking 连续下料加工progressive drawing 连续引申加工reaming 铰孔加工scrapless machining 无废料加工shaving 缺口修整加工shearing 切断加工

staking 铆固stamping 锻压加工a ccumulator 蓄压器actuator 驱动器adapter 接头back shaft 支撑轴blank determination 胚料展开

board drop hanmmer 板落锤brake 煞车camlachie cramp 铸包

casting on flat 水平铸造chamotte sand 烧磨砂charging hopper 加料漏斗

clutch brake 离合制动器coil car 带卷升降运输机coil cradle 卷材进料装置

coil reel stand 钢材卷料架cradle 送料架 crank 曲柄轴crankless 无曲柄式

cross crank 横向曲轴dial feed 分度送料die assembly 合模

double crank press 双曲柄轴冲床film play 液面花纹

fine blanking press 精密下料冲床formboard 进模口架frame 床身机架

金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals

刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission

轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error

响应 response 定位 allocation 机床夹具 jig 动力学 dynamic

运动学 kinematic 静力学 static 分析力学 analyse mechanics

拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist

弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC

磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor

几何形状 geometrical 精度 precision 正弦形的 sinusoid

交流电路 AC circuit 机械加工余量 machining allowance 变形力 deforming force 变形 deformation 应力 stress 硬度 rigidity 热处理 heat treatment

退火 anneal 正火 normalizing 脱碳 decarburization

渗碳 carburization 电路 circuit 半导体元件 semiconductor element

反馈 feedback 发生器 generator 直流电源 DC electrical source

门电路 gate circuit 逻辑代数 logic algebra 外圆磨削 external grinding

内圆磨削 internal grinding 平面磨削 plane grinding 变速箱 gearbox

离合器 clutch 绞孔 fraising 绞刀 reamer

螺纹加工 thread processing 螺钉 screw 铣削 mill

铣刀 milling cutter 功率 power 工件 workpiece

齿轮加工 gear machining 齿轮 gear 主运动 main movement

主运动方向 direction of main movement 进给方向 direction of feed

进给运动 feed movement 合成进给运动 resultant movement of feed

合成切削运动 resultant movement of cutting

合成切削运动方向 direction of resultant movement of cutting 切削深度 cutting depth

前刀面 rake face 刀尖 nose of tool 前角 rake angle

后角 clearance angle 龙门刨削 planning 主轴 spindle

主轴箱 headstock 卡盘 chuck 加工中心 machining center

车刀 lathe tool 车床 lathe 钻削镗削 bore 车削 turning

磨床 grinder 基准 benchmark 钳工 locksmith 锻 forge

压模 stamping 焊 weld 拉床 broaching machine 拉孔 broaching

装配 assembling 铸造 found 流体动力学 fluid dynamics 流体力学 fluid mechanics

加工 machining 液压 hydraulic pressure 切线 tangent

机电一体化 mechanotronics mechanical-electrical integration

气压 air pressure pneumatic pressure 稳定性 stability 介质 medium

液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve

失效 invalidation 强度 intensity 载荷 load 应力 stress

安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix

键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing

弹簧 spring 制动器 arrester brake 十字结联轴节 crosshead

联轴器 coupling 链 chain

机械专业英语词汇(二)

皮带 strap 精加工 finish machining 粗加工 rough machining

变速箱体 gearbox casing 腐蚀 rust 氧化 oxidation 磨损 wear

耐用度 durability 随机信号 random signal 离散信号 discrete signal

超声传感器 ultrasonic sensor 集成电路 integrate circuit 挡板 orifice plate

残余应力 residual stress 套筒 sleeve 扭力 torsion 冷加工 cold machining

电动机 electromotor 汽缸 cylinder 过盈配合 interference fit 热加工 hotwork

摄像头 CCD camera 倒角 rounding chamfer 优化设计 optimal design

工业造型设计 industrial moulding design 有限元 finite element 滚齿 hobbing

插齿 gear shaping 伺服电机 actuating motor 铣床 milling machine

钻床 drill machine 镗床 boring machine 步进电机 stepper motor 丝杠 screw rod

导轨 lead rail 组件 subassembly

可编程序逻辑控制器 Programmable Logic Controller PLC

电火花加工 electric spark machining 电火花线切割加工 electrical discharge wire – cutting 相图 phase diagram 热处理 heat treatment 固态相变 solid state phase changes

有色金属 nonferrous metal 陶瓷 ceramics 合成纤维 synthetic fibre

电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension

向器 redirector 变速器 speed changer 板料冲压 sheet metal parts

孔加工 spot facing machining 车间 workshop 工程技术人员 engineer

气动夹紧 pneuma lock 数学模型 mathematical model

画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection

视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing

装配图 assembly drawing 尺寸标注 size marking 技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement

截面 section 疲劳极限 fatigue limit 断裂 fractur

塑性变形 plastic distortion 脆性材料 brittleness material

刚度准则 rigidity criterion 垫圈 washer 垫片 spacer

直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear

直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch

齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear

虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams

共轭曲线 conjugate curve 范成法 generation method

定义域 definitional domain 值域 range 导数\\微分 differential coefficient

求导 derivation 定积分 definite integral 不定积分 indefinite integral

曲率 curvature 偏微分 partial differential 毛坯 rough

游标卡尺 slide caliper 千分尺 micrometer calipers 攻丝 tap

二阶行列式 second order determinant 逆矩阵 inverse matrix

线性方程组 linear equations 概率 probability

随机变量 random variable 排列组合 permutation and combination

气体状态方程 equation of state of gas 动能 kinetic energy 势能 potential energy

机械能守恒 conservation of mechanical energy 动量 momentum

桁架 truss 轴线 axes 余子式 cofactor 逻辑电路 logic circuit

触发器 flip-flop 脉冲波形 pulse shape 数模 digital analogy

液压传动机构 fluid drive mechanism 机械零件 mechanical parts

淬火冷却 quench 淬火 hardening 回火 tempering

调质 hardening and tempering 磨粒 abrasive grain 结合剂 bonding agent

砂轮 grinding wheel 机床行业部分英汉对照

按英文字母排序

3-Jaws indexing spacers 三爪、分割工具头 A.T.C.system 加工中心机刀库Aluminum continuous melting & holding furnaces 连续溶解保温炉

Balancing equipment 平衡设备Bayonet 卡口Bearing fittings 轴承配件Bearing processing equipment 轴承加工机Bearings 轴承Belt drive 带传动Bending machines 弯曲机Blades 刀片Blades,saw 锯片

Bolts,screws & nuts 螺栓,螺帽及螺丝 Boring heads 搪孔头Boring machines 镗床Cable making tools 造线机Casting,aluminium 铸铝Casting,copper 铸铜Casting,gray iron 铸灰口铁Casting,malleable iron 可锻铸铁

Casting,other 其他铸造Casting,steel 铸钢Chain drive 链传动

Chain making tools 造链机Chamfer machines 倒角机Chucks 夹盘Clamping/holding systems 夹具/支持系统CNC bending presses 电脑数控弯折机

CNC boring machines 电脑数控镗床CNC drilling machines 电脑数控钻床

CNC EDM wire-cutting machines 电脑数控电火花线切削机

CNC electric discharge machines 电脑数控电火花机

CNC engraving machines 电脑数控雕刻机CNC grinding machines 电脑数控磨床CNC lathes 电脑数控车床CNC machine tool fittings 电脑数控机床配件CNC milling machines 电脑数控铣床CNC shearing machines 电脑数控剪切机CNC toolings CNC刀杆CNC wire-cutting machines 电脑数控线切削机Conveying chains 输送链Coolers 冷却机Coupling 联轴器

Crimping tools 卷边工具Cutters 刀具Cutting-off machines 切断机Diamond cutters 钻石刀具Dicing saws 晶圆切割机Die casting dies 压铸冲模Die casting machines 压铸机Dies-progressive 连续冲模

Disposable toolholder bits 舍弃式刀头Drawing machines 拔丝机

Drilling machines 钻床Drilling machines bench 钻床工作台

Drilling machines,high-speed 高速钻床Drilling machines,multi-spindle 多轴钻床Drilling machines,radial 摇臂钻床Drilling machines,vertical 立式钻床drills 钻头Electric discharge machines(EDM) 电火花机Electric power tools 电动刀具Engraving machines 雕刻机

Engraving machines,laser 激光雕刻机Etching machines 蚀刻机

Finishing machines 修整机Fixture 夹具Forging dies 锻模

Forging,aluminium 锻铝Forging,cold 冷锻Forging,copper 铜锻Forging,other 其他锻造Forging,steel 钢锻Foundry equipment 铸造设备

Gear cutting machines 齿轮切削机Gears 齿轮

Gravity casting machines 重力铸造机Grinder bench 磨床工作台

Grinders,thread 螺纹磨床Grinders,tools & cutters 工具磨床Grinders,ultrasonic 超声波打磨机Grinding machines 磨床

Grinding machines,centerless 无心磨床Grinding machines,cylindrical 外圆磨床Grinding machines,universal 万能磨床Grinding tools 磨削工具

Grinding wheels 磨轮Hand tools 手工具

Hard/soft and free expansion sheet making plant 硬(软)板(片)材及自由发泡板机组

Heat preserving furnaces 保温炉Heating treatment funaces 熔热处理炉Honing machines 搪磨机Hydraulic components 液压元件Hydraulic power tools 液压工具Hydraulic power units 液压动力元件

Hydraulic rotary cylinders 液压回转缸Jigs 钻模Lapping machines 精研机Lapping machines,centerless 无心精研机Laser cutting 激光切割

Laser cutting for SMT stensil 激光钢板切割机Lathe bench 车床工作台Lathes,automatic 自动车床Lathes,heavy-duty 重型车床

Lathes,high-speed 高速车床Lathes,turret 六角车床

Lathes,vertical 立式车床Lubricants 润滑液 Lubrication Systems 润滑系统Lubricators 注油机Machining centers,general 通用加工中心

Machining centers,horizontal 卧式加工中心

Machining centers,horizontal & vertical 卧式及立式加工中心

Machining centers,vertical 立式加工中心

Machining centers,vertical double-column type 立式双柱加工中心

Magnetic tools 磁性工具Manifolds 集合管Milling heads 铣头

Milling machines 铣床Milling machines,bed type 床身式铣床

Milling machines,duplicating 仿形铣床Milling machines,horizontal 卧式铣床Milling machines,turret vertical 六角立式铣床Milling machines,universal 万能铣床Milling machines,vertical 立式铣床

Milling machines,vertical & horizontal 立式及卧式铣床

Mold & die components 模具单元Mold changing systems 换模系统

Mold core 模芯Mold heaters/chillers 模具加热器/冷却器

Mold polishing/texturing 模具打磨/磨纹Mold repair 模具维修

Molds 模具Nail making machines 造钉机Oil coolers 油冷却器Overflow cutting machines for aluminium wheels 铝轮冒口切断机

P type PVC waterproof rolled sheet making plant P型PVC高分子防水

PCB fine piecing systems 印刷电器板油压冲孔脱料系统

Pipe & tube making machines 管筒制造机Planing machines 刨床

Planing machines vertical 立式刨床Pneumatic hydraulic clamps 气油压虎钳Pneumatic power tools 气动工具

Powder metallurgic forming machines 粉末冶金成型机

Presses,cold forging 冷锻冲压机presses,crank 曲柄压力机

Presses,eccentric 离心压力机Presses,forging 锻压机Presses,hydraulic 液压冲床Presses,knuckle joint 肘杆式压力机Presses,pneumatic 气动冲床Presses,servo 伺服冲床

Presses,transfer 自动压力机Pressing dies 压模

Punch formers 冲子研磨器Quick die change systems 速换模系统Quick mold change systems 快速换模系统Reverberatory furnaces 反射炉

Rollers 滚筒Rolling machines 辗压机Rotary tables 转台Sawing machines 锯床Sawing machines,band 带锯床Saws,band 带锯Saws,hack 弓锯Saws,horizontal band 卧式带锯

Saws,vertical band 立式带锯shafts 轴Shapers 牛头刨床

Shearing machines 剪切机Sheet metal forming machines 金属板成型机Sheet metal working machines 金属板加工机Slotting machines 插床spindles 主轴Stamping parts 冲压机Straightening machines 矫直机Switches & buttons 开关及按钮Tapping machines 攻螺丝机

Transmitted chains 传动链Tube bending machines 弯管机

V ertical hydraulic broaching machine 立式油压拉床Vises 虎钳

Vises,tool-maker 精密平口钳Wheel dressers 砂轮修整器Woven-Cutting machines 织麦激光切割机Wrenches 扳手

单价unit price 工日合计Man-day total/work-day total

人工费cost of labor 材料费materials expenses

机械的mechanical 检查接线connection test

发电机generator 调相机phase regulator 周波cycle

减负荷装置load-shedding equipment 断路器柜circuit breaker cabinet

单母线single busbar 互感器transformer 每相电流Current by Phase

封闭式插接close type socket joint 发电机控制面板generator control panel

分级卸载sorted unloading 同步控制synchronization control

调速器speed governor 信号屏signal screen 继电器relay

高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer

空气断路器air circuit breaker 控制屏control panel

直流馈电屏direct current feed control panel 电容器electric condenser

计量盘metering panel 成套配电箱whole set of distribution box

落地式floor model 控制开关Control switches

铜芯电力电缆Copper core power cable 控制电缆actuating cable

热缩式电力电缆终端头pyrocondensation power cable terminal

钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel

电缆托架cable bracket

钢制托盘式桥架steel Tray-type cable support system

waterproof socket 防水插座防爆插座Explosion-proof socket

接地绞线earthing twisted pair 接地母线earthing bus

接地极lightning conductor 硬质聚氯乙烯管rigid polyvinyl chloride pipe

航空集散站air terminal 水银灯具Mercury Lamp

金属卤化物灯metal halide lamp 高压钠灯High Pressure Sodium Lamp

额定电压Rated V oltage 额定功率Rated Power 光源Light Source

防护等级Grade of Protection 高压汞灯High Pressure Mercury Lamp

高压钠灯High Pressure Sodium Lamp 金属卤化物灯Metallic Halide Lamp

照明电缆lighting cable 单线mongline 穿线threading

接地跨接线earthing jumper 分线箱junction box 接线盒connection box

圆钢round steel 扁钢flat steel 插座socket 配电盘switchboard

转换开关alternation switch 自动指令呼叫装置automatic instruction calling device 扬声器loudspeaker 明装Unfold Install 暗装Conceal Install

感温探测器Thermal Detector

恒温·干燥器/恒温恒湿器Drying Ovens/Humidity Chambers---(在重庆有OEM生产)

送风定温恒温器Forced Convection Constant Temperature Ovens

惰性气体恒温器Inert Gas Ovens

精密恒温器Precision Constant Temperature Ovens

洁净恒温器Clean Ovens

送风定温干燥器Forced Convection Constant Temperature Drying Ovens

空气幕送风定温恒温器Forced Convection Ovens With Air Curtain

定温干燥箱Constant Temperature Drying Ovens

角形真空定温干燥器V acuum Drying Ovens

恒温恒湿器Constant Temperature and Humidity Chambers

流水线设备In-Line System for Underfill Adhesive and Encapsulation

恒温培养器Constant Temperature Incubators---

可程式低温培养器Low Temperature Program Type Incubators

低温培养器Low Temperature Incubators

低温稳定性培养器Low Temperature Stability Incubators

培养器Incubators CO2培养器CO2 Incubators

振荡培养器Shaking Incubators 冻结干燥器Freeze Dryers---

冻结干燥器Freeze Dryers 离心形冻结干燥器Centrifugal Freeze Dryers 灭菌器Sterilizers--- 干热灭菌器Drying Sterilizers

高压灭菌器Autoclaves Sterilizers

低温等离子灭菌器Low Temperature Plasma Sterilizers

环形燃烧管灭菌器Loop Cinerator 纯水制造装置Water Purifiers---

纯水制造装置Water Stills 超纯水制造装置Ultra-pure Water Purifiers

简易纯水制造装置Water Purifiers

超纯水制造装置系统Ultra-pure Water Purifier System

大容量纯水制造装置Water Purifiers System

洗净器Washers--- 实验室玻璃器皿清洗机Laboratory Glassware Washers

超声波清洗机Ultrasonic Cleaners

大型超声波清洗机Aqueous Ultrasonic Cleaning Systems

超声波试管清洗机Ultrasonic Pipet Washers

超声波清洗机Ultrasonic Cleaners

恒温液槽Constant Temperature Baths---

投入式恒温装置Constant Temperature Devices

油槽Oil Baths 振荡式低温水槽Low Constant Temperature Shaking Baths

深槽形恒温水槽Constant Temperature Water Baths

粘度测定槽Kinematic Viscosity Baths

液压式恒温水槽Constant Temperature Water Baths

精密低温恒温水槽Precision Low Constant Temperature Water Baths

低温恒温水槽Low Constant Temperature Water Baths

试验管加热板Heating Blocks 冷却液体循环器Cooling Liquid Circulators cardan shaft万向联轴节companion flange成对法兰结合法兰配对法兰screw 螺丝钉packing list 装箱单hydraulic 液压的roller press液压机bearing 活动轴承bore钻孔thread穿线hexagon nut六角螺母spring lock washer螺丝弹簧垫片hand pump 手动泵grease润滑油

file 锉screw clamp 螺丝钳sliding caliper游标卡尺vice抬物架hose胶皮管tube fitting 管接头cyl.roller bearing 轴承

thrust roll. bear. spherical 轴承spheric. pl. bearing 球面轴承sliding plate 滑板tyre 轮带flat packing 密封shaft lip seal 密封v-seal v-密封

o-ring o形圈compression spring 弹簧垫片pumping element 泵件progr. distributor分配器gasket set密封圈装置rubber plate 橡胶板bellows 橡胶防尘罩(风箱) transm. pressure 压力表,压力传动器

filter element 过滤芯geared pump齿轮泵prop.contr.valve阀

gasket密封pressure gauge压力表sight glass量位计einbaruventil 阀hose管子lift check valve阀diff.pressure gaue压力表

diaph. accumulator气串瓶speicherblase气串temperature sensor传感器

gas-valve insert阀芯ventileinheit阀芯clutch/coupling连轴带srppressor plug插座level switch 开关sandwich plate夹层板

direct.contr.valve直控阀ventilating filter滤芯flow control valve

by-pass valve旁通阀, 辅助阀, 回流阀tubular cored ele.焊丝cored-wire焊丝plug-in connector 插座接头pulse generator脉冲发生器

proximity switch inductive非接触式电感开关sensor传感器pick-up传感器monitoring transd.变送器hexagon bolt六角螺栓

spring lock washer弹簧锁架垫片resist.thermometer oil leak-proof油封式变阻温度计resist.thermometer变阻温度计screw flat countersunk nib bolt螺旋平头垫头螺栓heating cable耐热电缆connection set连接装置

controller electronic电子调节器,电控装置alum.adjesove tape 胶带

threaded joint螺纹接合hose assembly软组件twin nipple双喷嘴measuring instrument计量工具bracket支座support支座

hydr.cyl.flat type液压缸(板型),水平水压气缸rotary seal回转密封

threaded rod螺纹杆hexagon nut六角螺母pression hose压力软管

hose clip软管卡l-section组装列表pump set泵机组

control block hydraulic unit with control液压控制部件

机械类常用英语词汇大全

机械类常用英语词汇大全 一字螺丝批 slot type screwdriver 一点透视 one-point perspective 二画 二合一黏合剂 epoxy resin adhesive 二合胶;混合胶 epoxy glue 二维的;平面的 two-dimensional 二进制 binary 二极管;整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的;公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学 ergonomics; human engineering 人体尺寸 human dimension 人体测量学 anthropometry; anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷;床鞍 apron 刀座鞍;溜板座 saddle 力 force 力三角形 triangle of force 力平行四边形 parallelogram of force 力多边形;多边形力学 polygon of force 力的分解 force resolution 力架;亮漆 lacquer 力矩 moment 力偶 couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip s head screw 十字螺丝批 Philip s type screwdriver 丁字尺;T 尺 tee square 三画 三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的;立体的 three-dimensional 三氯甲烷;哥罗芳 chloroform 三聚氰胺;蜜胺 melamine 三点透视 three-point perspective 上油漆 painting 上釉 enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力;虫漆 shellac 士巴拿;扳手 spanner 大芯夹板;宽条芯夹板 blockboard; solid corestock-laminated board 大量制造 mass production

专业英语词汇:机械加工

抛光 polishing 安装 to assemble 扳手 wrench 半机械化 semi-mechanization; semi-mechanized 半自动滚刀磨床 semi-automatic hob grinder 半自动化 semi-automation; semi-automatic 备件 spare parts 边刨床 side planer 变速箱 transmission gear 柄轴 arbor 部件 units; assembly parts 插床 slotting machine 拆卸 to disassemble 超高速内圆磨床 ultra-high-speed internal grinder 车床 lathe; turning lathe 车刀 lathe tool 车轮车床 car wheel lathe 车削 turning 车轴 axle 衬套 bushing 按英文字母排序 3-Jaws indexing spacers 三爪、分割工具头 A.T.C.system 加工中心机刀库 Aluminum continuous melting & holding furnaces 连续溶解保温炉Balancing equipment 平衡设备 Bayonet 卡口 Bearing fittings 轴承配件 Bearing processing equipment 轴承加工机 Bearings 轴承 Belt drive 带传动 Bending machines 弯曲机 Blades 刀片 Blades,saw 锯片 Bolts,screws & nuts 螺栓,螺帽及螺丝 Boring heads 搪孔头 Boring machines 镗床 Cable making tools 造线机 Casting,aluminium 铸铝 Casting,copper 铸铜 Casting,gray iron 铸灰口铁 Casting,malleable iron 可锻铸铁

机械工程图中常用的英语词汇

机械工程图中常用的英语词汇 A Abbreviation 缩写 Accuracy 精度、准确性 Acme thread 梯形螺纹(29°) Addendum 齿顶高 Addendum angle 齿顶角 Addendum circle 齿顶圆 Addendum of mating gear 啮合齿轮的齿顶高 Adjacent-part lines 相邻零件线 Aligned sections 旋转剖视 Aligned view旋转视图 Allowance 容差、加工余量 Alloy 合金 Alloy steel 合金钢 Alphabet 字母 Alteration 变更、更改 Alternate-position views 位置改变的视图 Alternator 交流发电机 Induction alternator 感应(交流)发电机 Motor alternator 电动(交流)发电机 Single-phase alternator 单向(交流)发电机 Synchronous alternator 同步(交流)发电机 Three-phase alternator 三相(交流)发电机 Amount 总量、总计 Analyzable assembly 分析装配图 Anchor bolt 地脚螺栓 Angles 角 Acute angle 锐角 Blunt angle 钝角 Right angle 直角 Sliding angle 摩擦角 Spiral angle 螺旋角 Taper angle 锥角 Angular 有角的 Angular bearing 径向止推轴承 Angular bevel gears 斜交伞齿轮 Angular gear人字齿轮 Angular section斜剖面 Anneal 退火 Approval 批准、许可 Arc 弧、圆弧

机械词汇表(1)

机械词汇表(1) 渐开线圆柱齿轮图样上应注明的尺寸数据Involute cylindrical gears--Information of the dimensional data to be given on the drawing 机械振动平衡术语Mechanical vibration--Balancing vocabulary 滚动轴承滚轮滚针轴承外形尺寸Rolling bearings Needle roller bearings--Track rollers--Boundary dimensions 滚动轴承滚轮滚针轴承公差Rolling bearings--Needle roller bearings-Track rollers--Tolerances 齿轮渐开线样板The involute master of gear 齿轮螺旋线样板The helix master of gear 机械密封的型式、主要尺寸、材料和识别标志Type, main dimension, material and marking of mechanical seals 挠性转子机械平衡的方法和准则Mechanical vibration--Methods and criteria for the mechanical balancing of flexible rotors 自攻锁紧螺钉的螺杆粗牙普通螺纹系列Screw thread shanks for thread forming screw--Metric coarse thread series 十字槽盘头自攻锁紧螺钉Cross recessed pan head thread forming screws 十字槽沉头自攻锁紧螺钉Cross recessed countersunk head thread forming screws 十字槽半沉头自攻锁紧螺钉Cross recessed raised countersunk head thread forming screws 六角头自攻锁紧螺钉Hexagon head thread forming screws 内六角花形圆柱头自攻锁紧螺钉Hexagon lobular socket thread forming screws 机床润滑系统Machine tools--Lubrication systems 铁氧体永磁直流电动机DC ferrite permanent magnet motors 滚动轴承词汇Rolling bearings--V ocabulary 带传动基本术语Drives using belt--Basic terminology V 带传动术语Drives using V-belts and grooved pulleys--Terminology 同步带传动术语Synchronous belt drives--Terminology 凸缘外圈向心球轴承凸缘尺寸Radial ball bearings with flanged outer ring--Flange dimensions 滚动轴承凸缘外圈微型向心球轴承外形尺寸Rolling bearings--Miniature radial ball bearings with flanged outer ring Boundary dimensions 现场平衡设备的说明和评价Field balancing equipment--Description and evaluation 重型弹簧垫圈Single coil spring lock washers, Heavy type 鞍形弹簧垫圈Curved single coil spring lock washers 波形弹簧垫圈Wave single coil spring lock washers 可靠性、维修性与有效性预计报告编写指南Presentation of reliability, maintainability and availability predictions 55°密封管螺纹第1部分: 圆柱内螺纹与圆锥外螺纹Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads Part 1: Parallel internal and taper external threads 55°密封管螺纹第2部分: 圆锥内螺纹与圆锥外螺纹Pipe threads with 55 degree thread angle where pressure-tight joints are made on the threads Part 2: Taper internal and external threads

机械专业英语词汇汇总

机械专业英语词汇(大全) 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck 加工中心machining center

机械专业词汇2

机械专业词汇 速度:Geschwindigkeit 动量:Bewegungsgroesse 摩擦:Reibung 动能:kinetische Energie 碰撞:zusammenstossen 质点:Partikel 抛物线:Parabel 万有引力:Gravitations 定理:Gesetz 光波:lichtwelle 波长:wellenlaenge 波:Welle 横波:Ouerwelle 纵波:laengswelle 场强:Feldstaerke 电势:elektrisches Potenzial 电势差:Potenzialdifferenz 电容:Kapazitaet 反向电流:inverser Strom gegenstrom 结构分析:strukturanalyse 自由度:Freiheitsgrad 转动:drehen 电路:Stromkreis 电压:Spannung 交变电流:wechselstrom 直流电流:Gleichstrom 节点:Gelenk 支路:nebenstrasse Seitenstrasse

电源:Stromquelle 互导:steilheit 互感:Gegeninduktion 电桥:Brueckenschaltung 电桥臂:Bruechenarm 尺寸公差:Toleranz 基本尺寸:grundmass 极限尺寸:Grenzmaass 偏差:Abmass 配合:zusammenspiel 公差带:Toleranz breite 公差带及配合:spielsitz 孔:Loch 轴:Achse 基孔制:Einheitsbohrung 基轴制:Bezugsachse 总和:Gesamtheit 俯视图:Aufsicht 视图:Ansicht 前视图:Vorderansicht 侧视图:Seitenansicht 三维:dreidimensional 切削:spanen schneiden 刀具: Stahl meissel 切削方向:Schnittrichtung 切削液:Schneidwasser 切削加工:Spanende bearbeitung 切削速度:schnittgeschwindigkeit 切削面:schnittflaeche 切削性:schneidbarkeit

机械类常用术语

机械类常用术语 计算机辅助设计与制造系统CAD/CAM system 计算机数控computer numerical control (CNC) 计算机数控车床CNC lathe 电路circuit 电磁线圈;筒形线圈;螺线管solenoid 电枢;衔铁线圈armature 电线electric wire 电线退皮钳wire stripper 电导率electrical conductivity 电导量conductance 电压voltage 电压比voltage ratio 十四画 划针scriber 划线layout; marking out; ruling 划线刀marking knife 划线工具marking tool 划线规marking gauge; surface gauge 划线轮stitch marker 图形表达技巧graphic presentation technique 图案;花样pattern 图框drawing frame 图画的阴暗部shade 图画纸cartridge paper 图象传意graphical communication 图头钉French nail 垫片;垫圈;介子gasket; washer 垫板;台垫bench hook 垫料backing 实践计划realization 对比contrast 对流convection

对接butt 对接合;对接榫butt joint 对接角榫butt mitred joint 对接焊butt welding 对称symmetry 惯性力矩;转动惯量moment of inertia 惯性负载inertia load 截锥铆钉pan head rivet 折尺folding rule 折床;弯曲机bending machine 折铁砧hatchet stake 折铁器folding bar 敲打成形beatening 杠杆lever 构件member 构成作业fabrication process 构架接合;构架榫framed joint 构架结构frame construction 构想;意念idea 榫头tenon 榫眼;卯孔mortise 榫规;双线规mortise gauge 榫锯;夹背锯tenon saw 榫凿mortise chisel 槌击法chopping 演绎技术(设计) rendering technique 滚子轴承roller bearing 滚花身;压花身knurled shank 滚珠轴承ball bearing 滚纹;切辊纹knurling 滚动摩擦rolling friction 滚压;辘压rolling 漏电断路掣;水气掣earth leakage circuit breaker (ELCB) 滞后现象hysteresis

(完整版)机械工程专业英语词汇

陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams

机械行业专业术语

组装、冲压、喷漆等专业词汇 Assembly line 组装线Layout 布置图 Conveyer 流水线物料板Rivet table 拉钉机 Rivet gun 拉钉枪Screw driver 起子 Electric screw driver 电动起子Pneumatic screw driver 气动起子worktable 工作桌OOBA 开箱检查 fit together 组装在一起fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码barcode scanner 条码扫描器 fuse together 熔合fuse machine 热熔机 repair 修理operator 作业员 QC 品管supervisor 课长 ME 制造工程师MT 制造生技 cosmetic inspect 外观检查inner parts inspect 内部检查 thumb screw 大头螺丝lbs. inch 镑、英寸 EMI gasket 导电条front plate 前板 rear plate 后板chassis 基座 bezel panel 面板power button 电源按键 reset button 重置键Hi-pot test of SPS 高源高压测试 Voltage switch of SPS电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件SOP 制造作业程序 material check list 物料检查表work cell 工作间 trolley 台车carton 纸箱 sub-line 支线left fork 叉车 personnel resource department人力资源部production department 生产部门planning department 企划部QC Section 品管科 stamping factory 冲压厂painting factory 烤漆厂 molding factory 成型厂common equipment 常用设备 uncoiler and straightener 整平机punching machine 冲床

机械专业英语高频词汇讲解

机械专业英语高频词汇 metal cutting 金属切削 machine tool 机床 technology of metals金属工艺学 cutter 刀具 friction 摩擦 link 联结 drive/transmission 传动 shaft 轴 elasticity 弹性 frequency characteristic 频率特性 error 误差 response响应 allocation 定位 jig 机床夹具 term 语术 d ynamic 动力学 k inematic运动学 s tatic 静力学 a nalyse mechanics 分析力学 p ulling 拉伸 s hear 剪切 t wist 扭转 b ending stress 弯曲应力 i ntensity 强度 t hree-phase AC 三相交流电 m agnetic circles 磁路 t ransformer变压器 a synchronous motor 异步电动机 g eometrical 几何形状 p recision 精度 s inusoid 正弦形的 h itting压缩 A C circuit 交流电路 m achining allowance 机械加工余量 d eforming forc e 变形力 d eformation 变形 s tress 应力 r igidity 硬度 r igidity 刚度 h eat treatment 热处理 d ecarburization 脱碳 c ircuit 电路

f raising铰孔 semiconductor element 半导体元件 f eedback 反馈 g enerator 发生器 D C electrical source直流电源 g ate circuit 门电路 l ogic algebra//////algorithm逻辑代数 e xternal grinding 外圆磨削 internal grinding内圆磨削 p lane grinding 平面磨削 c arburization 渗碳 gearbox 变速箱 c lutch 离合器 r eamer铰刀 t hread processing 螺纹加工 s crew 螺钉 m ill 铣削 m illing cutter 铣刀 p ower 功率 w orkpiece 工件 g ear machining 齿轮加工 g ear 齿轮 m ain movement 主运动 d irection of main movem 主运动方向ent d irection of feed进给方向 f eed movement 进给运动 r esultant movement of fe 合成进给运动ed r esultant movement of cut 合成切削运动ting d irection of resultant cutting 合成切削运动方向motion c utting depth 切削深度 r ake face 前刀面 n ose of tool刀尖 r ake angle 前角 c learance angle 后角 p laning 龙门刨削 s pindle 主轴 h eadstock主轴箱 c huck 卡盘 m achining center 加工中心 l athe tool 车刀 l athe 车床 b ore 钻削镗削 t urning车削 g rinder 磨床

机械工程专业英语单词

Lesson 1 Basic Concepts in M e c h a n i c s机械学的基本概念mechanics n.力学 modify v.修改,调解,变更manageable a.可控制【管理】的incline v.(使)倾斜 ramp n.斜板,斜坡【道】slope v.(使)倾斜 friction n.摩擦 roll v.滚动 multiplier n.放大器,乘法器broom n.扫帚 convert v.转变【化】 handle n.手柄【把】 sweep v.扫荡【描】,掠过efficiency n.效率 gauge vt.测【计】量,校验bearing n.轴承 ideal mechanical advantage 理想的机械效益 neglect vt.忽略Lesson 2 Basic Assumption in Plasticity Theory 塑性理论的基本假设 assumption n.假定 plasticity n.塑性 investigate v.调查,研究deformation n.变形 metal forming process 金属成型工艺【过程】 strain (rate) n.应变【速率】strength n.强度 stress n.应力 yield stress 屈服应力 flow stress 流动应力 tensile stress 拉【伸】应力compressive stress 压【缩】应力shear stress 剪【切】应力geometry n.几何形状 elastic a.弹性的 springback n.回弹 bending n.弯曲,折弯

常用机械英语单词

金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematics 静力学static 分析力学analysis mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarbonization 渗碳carboniz ation 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding

机械设计及生产常用专业英语单词

机械设计及生产常用专业英语单词 Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Pneum atic screw driver 气动起子worktable 工作桌 OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板 barcode 条码 barcode scanner 条码扫描器 fuse together 熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME 制造工程师 MT 制造生技 cosmetic inspect 外观检查 inner parts inspect 内部检查 thumb screw 大头螺丝 lbs. inch 镑、英寸 EMI gasket 导电条 front plate 前板 rear plate 后板 chassis 基座 bezel panel 面板 power button 电源按键 reset button 重置键 Hi-pot test of SPS 高源高压测试Voltage switch of SPS 电源电压接拉键sheet metal parts 冲件 plastic parts 塑胶件 SOP 制造作业程序 material check list 物料检查表 work cell 工作间 trolley 台车

sub-line 支线 left fork 叉车 personnel resource departm ent 人力资源部 production departm ent生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 planer |plein|刨床 miller铣床 grinder磨床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺 final inspection终检 to connect material接料 to reverse material 翻料 wet station沾湿台

机械专业相关词汇中英文翻译大全

机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus

机械类常用英语词汇大全

机械类常用英语词汇大全丙烯丁二烯苯乙烯acrylonitrile-butadiene-stryrene (ABS) 主轴;心轴spindle 主题motif 令(纸张的计数单位) ream 凹座recess 凹模hollowing block 凸缘flange 凸缘联轴节flange coupling 凸轮cam 凸轮式配件cam-action fitting 凸轮传动cam drive 凸头螺丝raised head screw 加成作业;添加法addition process 加油oiling 加速器accelerator 功能;用途function 功率因子power factor 功率放大器power amplifier 功率板power amplifier board 功率晶体管power transistor 包氏记号法Bow's notation

「包浩思」;「包豪斯」〈设计风格) Bauhaus 半永固法;半永久接合semi-permanent joining 半接榫halving joint 半闭式槽榫stopped housing joint 半圆(木)锉half-round rasp 半圆车刀turning gouge 半圆锉half-round file 半圆头铆钉snap rivet 半导体semiconductor 卡路里;卡(热量单位) calorie 卡纸card paper 卡尺;测径器calipers 去角;倒角chamfer 可切削性machinability 可行性feasibility 可逆过程reversible process 可压缩性compressibility 可变电阻variable resistor 四分仪quadrant 四爪夹头four-jaw independent chuck 四圆心法(绘图) four-centre method 外卡尺outside calipers

机械类专业词汇表

机械类专业词汇表2 Piping work: 铺管工程Steam trace: 加热蒸汽管道Cutting: 切割socket weld 承插焊接fillet weld 角焊,填角焊branch connection 分支接续fabricati on tolera nee.制造容差local heat treatment 局部热处理threaded pipe 螺纹管seal weldi ng.密圭寸焊接flange joint 凸缘接头undercut 底切feeder馈电线conduit outlet 电线引出口seal fitting 密圭接头, 密圭配件Screw thread lubrica nt 螺纹润滑剂Seal: 绝缘层weld reinforcement 焊缝补强lock washer 锁紧[止动, 防松]垫圈electrical panel.配电板,配电盘nipple 螺纹接头zinc plated.镀锌的ring joint 环接, 围缘接合bolt 螺栓control: 控制器 National Electrical Code 全国电气规程 master schedule 主要图表, 综合图表, 设计任务书, 主要作业表torque wrench 转矩扳手job site 施工现场flange conn ecti on.凸缘联接 Hard hat:安全帽 Goggles:护目镜stockpile 贮存packing list 装箱单crate: 柳条箱purchased material list 原材料进货单back-feed 反馈wire coil 线盘,线卷,NPT thread. 美国标准锥管螺纹cable gland 电缆衬垫terminal block 线弧, 接头排接线盒, 接线板, 线夹power drill 机械钻connector. 接线器in sulated sleeve 绝缘套管wire connector 接线器wire terminal 电线接头control wiring 控制线路motor lead 电动机引出线power wiring 电力布线ten der docume n t 提供证件orifice plate. 挡板nut 螺母flange gasket 法兰垫片dimensional inspection 尺寸检验burn through 烧蚀pipi ng system .管道系统reinforcement of weld 加强焊缝fabrication. 制造dye penetrant exam in ati on染料渗透试验法magnetic particle examination 磁粉检验girth weld 环形焊缝cement lined piping 水泥衬里weld joint 焊缝, 焊接接头spool drawing 管路图, 管路详图spot test 抽查, 当场测试butt weld 对接焊缝 Ran dom Radiography随机射线照相检查radiographic

机械专业英语词汇

机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient 求导derivation 定积分definite integral

相关主题