185104J50AHA-F中文资料

Type 168/185 Metallized Polyester Radial Lead Capacitors

Radial Box Metallized Polyester Capacitors for Automatic Insertion

Highlights

The Type 168/185 series radial lead metallized polyester box capacitors are available in bulk (Type 168) or on ammo pack or tape and reel (Type 185). These capacitors are constructed in rugged rectangular plastic cases and all come with 5.0 mm (0.197“) lead spacing. They are good for general purpose applications such as bypass, decoupling, energy storage/discharge and arc suppres-sion.

? Case and epoxy ?ll meets UL94V-0 ? 5.0 mm (0.197“) lead spacing ? Bulk, tape and reel or ammo pack ? Non-inductively wound ? Non-polar ? Low leakage

?

Lead material: Tinned copper wire

Speci?cations

Capacitance Range: Voltage Range: Capacitance Tolerance: Operating Temperature Range: Dielectric Withstand Voltage: Dissipation Factor (DF): RoHS Compliant

0.001 μF to 1.0 μF

50 Vdc to 400 Vdc (30 Vac to 200 Vac, 60 Hz)

±5%, ±10%, ±20%

–55 oC to +125 oC (with 50% Vdc derating >85 oC) 1.6 x rated voltage for 2 sec @ +25 oC ±5 oC

tan δ x 10 –4 at 25 oC ±5 oC

kHz C ≤0.1 μF C > 0.1 μF 1 ≤100 ≤100 10 ≤150 ≤150

100

≤300

Total Self Inductance (L): Approximately 7 nH

Long Term Stability (after two years): Capacitance change ?C/C ≤ ±3% under stan-dard environmental conditions Maximum Pulse Rise Time (dv/dt):

Vn V/μs 50 250 63 250 100 300 250 400 400

600

If the working voltage (V) is less than the nominal voltage (Vn), the capacitor can work at higher dv/dt. In this case, the maximum value allowed is obtained by multiplying the above value with the ratio Vn/V.

元器件交易网https://www.sodocs.net/doc/6a1778713.html,

Type 168/185 Metallized Polyester Radial Lead Capacitors

Capacitor Outline Drawing

Test Method and Performance

L T

Max

Max

H Max

.217 ±.039

(5.5 ±1.0 mm)

?d ±.002 S (±0.05)

±.015 (±0.4 mm)

Lead length shown is as supplied on the 168 Series

Soldering

Test Conditions

Soldering Temperature: 260 oC ±5 oC

Soldering Duration: 10 sec ±1 sec

Performance

Capacitance Change ?C/C: ≤ ±2%

DF Change ?tg δ: ≤30 x 10–4 at 10 kHz Insulation Resistance: ≥ limit value

Insulation Resistance

Test Conditions

Temperature: 25 oC ±5 oC

Voltage Charge Time: 1 minute

Voltage Charge: 10 Vdc for Vn < 100 Vdc

100 Vdc for Vn ≥ 100 Vdc

Performance

For Vn > 100 Vdc: C ≤ 0.33 μF, ≥15,000 MΩ

C > 0.33 μF, ≥ 5,000 S

For Vn ≤100 Vdc: C ≤ 0.33 μF, 30,000 MΩ

C > 0.33 μF, ≥ 10,000 S

Damp Heat Test

Test Conditions

Temperature: +40 oC Relative Humidity: 95% Test Duration: 21 days

Performance

Capacitance Change ?C/C: ±5%

DF Change ?tg δ: ≤ 0.005 (10 KHz) Insulation Resistance: ≥ 50% of limit value

Life Test

Test Conditions REF

Temperature: +85 oC Test Duration: 2000 hrs Voltage Applied: 1.25 x Vn

Performance

Capacitance Change ?C/C: ≤ ±2%

DF Change ?tg δ: ≤30 x 10–4 at 10 kHz Insulation Resistance: ≥ 50% of limit value

Ratings

RoHS Compliant

Catalog Part Number Tape & Reel Ammo Pack Cap (μF) Inches Millimeters L

T

H

S

?d

L

T

H

S

?d

50 Vdc / 30 Vac

168104*50A-F 185104*50#A>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168154*50A-F 185154*50#A>-F 0.15 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168224*50C-F 185224*50#C>-F 0.22 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168334*50C-F 185334*50#C>-F 0.33 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168474*50H-F 185474*50#H>-F 0.47 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168684*50F-F 185684*50#F>-F 0.68 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 168824*50G-F 185824*50#G>-F 0.82 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 168105*50G-F 185105*50#G>-F 1.00

0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6 63 Vdc / 40 Vac

168473*63A-F 185473*63#A>-F 0.047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168563*63A-F 185563*63#A>-F 0.056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168683*63A-F 185683*63#A>-F 0.068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168823*63A-F 185823*63#A>-F 0.082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168104*63A-F 185104*63#A>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168154*63C-F 185154*63#C>-F 0.15 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168184*63C-F 185184*63#C>-F 0.18 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168224*63C-F 185224*63#C>-F 0.22 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168274*63C-F 185274*63#C>-F 0.27 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168334*63H-F 185334*63#H>-F 0.33 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168474*63H-F 185474*63#H>-F 0.47 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168684*63F-F

185684*63#F>-F

0.68

0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168105*63G-F 185105*63#G>-F 1.00 0.283 0.236 0.433 0.197 0.024 7.2 6.0 11.0 5.0 0.6

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm (See H dimension in taping speci?cations)

元器件交易网https://www.sodocs.net/doc/6a1778713.html,

Type 168/185 Metallized Polyester Radial Lead Capacitors

RoHS Compliant

Catalog Part Number Tape & Reel Ammo Pack

Cap (μF)

Inches Millimeters L

T

H

S

?d

L

T

H

S

?d 100 Vdc / 63 Vac

168102*100A-F 185102*100#A>-F 0.0010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168152*100A-F 185152*100#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168222*100A-F 185222*100#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168272*100A-F 185272*100#A>-F 0.0027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168332*100A-F 185332*100#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168392*100A-F 185392*100#A>-F 0.0039 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*100A-F 185472*100#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168562*100A-F 185562*100#A>-F 0.0056 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*100A-F 185682*100#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168822*100A-F 185822*100#A>-F 0.0082 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168103*100A-F 185103*100#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168153*100A-F 185153*100#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168183*100A-F 185183*100#A>-F 0.018 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168223*100A-F 185223*100#A>-F 0.022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168273*100A-F

185273*100#A>-F 0.027 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168333*100C-F 185333*100#C>-F 0.033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168393*100C-F 185393*100#C>-F 0.039 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168473*100C-F 185473*100#C>-F 0.047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168683*100H-F 185683*100#H>-F 0.068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168104*100H-F 185104*100#H>-F 0.10 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168154*100F-F

185154*100#F>-F

0.15 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168224*100G-F 185224*100#G>-F 0.22

0.283 0.197 0.394 0.197 0.024 7.2 5.0 10.0 5.0 0.6 250 Vdc / 160 Vac

168332*250A-F 185332*250#A>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*250A-F 185472*250#A>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*250A-F 185682*250#A>-F 0.0068 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168103*250A-F 185103*250#A>-F 0.010 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168153*250A-F

185153*250#A>-F 0.015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168223*250C-F 185223*250#C>-F 0.022 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168333*250C-F 185333*250#C>-F 0.033 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168473*250F-F 185473*250#F>-F 0.047 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6 168683*250F-F

185683*250#F>-F 0.068 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168104*250G-F 185104*250#G>-F 0.100 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

400 Vdc / 200 Vac

168102*400A-F 185102*400#A>-F 0.001 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168152*400A-F 185152*400#A>-F 0.0015 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168222*400A-F

185222*400#A>-F 0.0022 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5

168332*400C-F 185332*400#C>-F 0.0033 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168472*400C-F 185472*400#C>-F 0.0047 0.283 0.098 0.256 0.197 0.020 7.2 2.5 6.5 5.0 0.5 168682*400C-F 185682*400#C>-F 0.0068 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168103*400F-F 185103*400#F>-F 0.010 0.283 0.138 0.295 0.197 0.020 7.2 3.5 7.5 5.0 0.5 168153*400F-F

185153*400#F>-F 0.015 0.283 0.177 0.374 0.197 0.024 7.2 4.5 9.5 5.0 0.6

168223*400G-F 185223*400#G>-F 0.022 0.283 0.197 0.394 0.197 0.024 7.2 5.0 10 5.0 0.6

* Indicates capacitance tolerance: J = ±5%, K = ±10%, M = ±20% # Indicates packaging type: R = Tape and Reel, A = Ammo Pack

> Indicates tooling code: A = 16.5 mm, B = 18.5 mm (See H dimension in taping speci?cation)

元器件交易网https://www.sodocs.net/doc/6a1778713.html,

Type 168/185 Metallized Polyester Radial Lead Capacitors Tape Speci?cation - 5.0 mm Lead Spacing

Item Code Millimeters Inches

Standard EIA-468-B

Lead-to-Lead Distance P 5.0+0.6 –0.2 .197+.024 –.040

Feed Hole Pitch P

12.7±0.3 .5±.012

Pitch of Component P

1

12.7±1.0 .5±.039

Hole Center to Lead P

2

3.85±0.7 .152±.028

Feed Hole Center to P

3

6.35±1.3 .250±.051

Component Center

Component Alignment, F-R ?h 0±2.0 0±.079

Tape Width W 18+1.0 –0.1 .709+.039 –.004

Hold-down Tape Width W

6.0 min .236 min

Hole Position W

1

9.0+0.75 –0.05 .355+.030 –.001

Hold-down Tape Position W

2

3.0 Max .118 Max

Height of Component H > >

from Tape Center

Feed Hole Diameter D

0 4.0±0.3 .157±.012

Case

Thickness Quantity Quantity

T Reeled Ammo Pack

2.5 2500 2000

3.5 1800 1500

4.5 1400 1300

5 1200 1000

6 1000 800

> The H dimension depends on the

insertion equipment used. Specify

the proper tooling code as indicated

below.

Tooling H Dimensions

Code Millimeters Inches

A

B

16.5±0.75

18.5±0.75

.679±0.030

.728±0.030

Part Numbering System for Auto Insertion

168/185 104 K 100 R H B –F

Packaging *Tooling RoHS

Type Internal Code Compliant Series Capacitance Tolerance Voltage (#) Code (>) Designation

185 102 = .001 μF J = ±5% 50 = 50 Vdc A = Ammo Letter A

103 = .01 μF K = ±10% 63 = 63 Vdc R = Tape & Reel B

104 = .1 μF M = ±20% 100 = 100 Vdc

105 = 1.0 μF 250 = 250 Vdc

400 = 400 Vdc

* Tooling code (>) depends on the users insertion equipment requirements. See table for available options. 元器件交易网https://www.sodocs.net/doc/6a1778713.html,