钻井常用英语
目录
TABLE OF CONTENTS
PART 1. 准备工作 (Getting Ready)
PART 2. 泥浆设计 (Mud Design)
PART 3. 配浆和处理 (Mixing And Treatment)
PART 4. 钻井工程A (Drilling Engineering A)
PART 5. 钻井工程B (Drilling Engineering B)
PART 6. 固相控制 (Solids Control)
PART 7. 井下复杂情况A (Complex Circumstance A)
PART 8. 井下复杂情况B (Complex Circumstance B)
PART 9. 泥浆房试验 (Testing In Mud House)
PART 10. 完井作业 (Completion)
PART 11. 作业安全 (Safety)
PART 12. 泥浆处理剂 (Mud Materials)
PART 13. 泥浆报表 (Mud Report)
PART 14. 公司介绍 (Service Introduction)
PART 1. 准备工作 (Getting Ready)
1.1 There will be strong wind, we have to wait on weather. 有强风，必须等候天气好转。
1.2 What materials can be unloaded to the boat?
那些物品可以卸到拖轮上？
1.3 The surplus Barite, Bentonite have to be transferred to the supply boat.
把多余的重晶石、般土粉运到拖轮上。
1.4 Where is the new location? What are the coordinates?
新井位在什么地方？经纬度多少？
1.5 When are we going to start moving?
什么时候开始拖航？
1.6 The Move may be start at eight thirty.
预计八点半起拖。
1.7 Speed up, please!
请快点干！
1.8 Have you checked all the mud equipments.
泥浆设备都检查过了吗？
1.9 Everything is O.K.
一切都正常。
1.10 The typhoon is coming. We will have to get everything ready to evacuate the rig.
台风快要来了，必须做好一切弃船准备。
1.11 Before making mud, clean all the circulation pipe-line and mud pits.
配浆前要认真清洗循环管线和配浆池。
1.12 Allow to yeild for six hours.
般土浆要预水化至少6小时。
1.13 Before spud, adjust the viscosity of bentonite sweep to over 80 seconds by adding Lim
e.
一开前，用石灰将般土浆粘度调至80秒以上。
1.14 Must prepare at least 200 cubic meter's slurry before spud.
开钻前应配好至少200方高粘度稠泥浆。
1.15 At least 80 tons Barite should be kept on hand at rig.
平台上必须储备至少80吨的重晶石粉。
PART 2. 泥浆设计 (Mud Design)
2.1 This is the drilling fluid's programme of WEIZHOU 12-1-3 well.
这是涠洲12－1－3井的泥浆设计书。
2.2 The proposed total depth of this well is 3900 meters.
这口井的设计井深是3900米。
2.3 What is the BHA of this well?
这口井的钻具组合是什么？
2.4 This is the hole geometry of this well.
这是这口井的井身结构。
2.5 The casing programme of this well is for 30” conductor (riser), 20” surface casing, 13 3/8” and 9 5/8” intermediate casing, and 7” liner.
本井的套管程序是：30英寸导管，20英寸表层套管，13 3/8和9 5/8英寸技术套管，最后下 7英寸尾管。
2.6 Mud program for the 12 1/4 inch interval is the PDF-PLUS mud, which is the PHPA polyme r.
12 1/4英寸井段采用PDF－PLUS泥浆体系，这是部分水解聚丙烯酰胺聚合物体系。
2.7 The surface intervals will be drilled with the seawater and gel sweeps.
表层采用海水钻进及稠泥浆进行清扫。
2.8 The PEM mud system has been successfully used on drilling operations in Bohai Gulf and S outh China Sea.
PEM泥浆体系曾经成功地应用于渤海和南海。
2.9 Mud density required for the well, which is expected to be in the range 1.05 to 1.10 S.
G. in 17 1/2 inch hole.
这口井17 1/2英寸井眼的钻井液密度为1.05到1.10 S.G.。
2.10 Fluid loss will be controlled below 5 ml in the 8 1/2 inch interval.
在8 1/2英寸井眼的钻井液失水要控制在5毫升以下。
2.11 Casing depths provided by the Operator.
(泥浆设计)所依据的套管深度是由作业者提供的。
2.12 The water depth is 108 meters, bushing high is 25 meters.
这口井的水深108米，补心高25米。
2.13 Hole volumes includes previous casing volume.
(泥浆设计中的)井眼体积包括前期套管的体积。
2.14 Open hole volume assumes gauge hole.
井眼体积以规则井眼假设。
2.15 Assumed 150 cubic meters surface volume.
(在泥浆设计中)假设地面循环体积为150方。
2.16 The brief target oil and gas zone are from 2300 to 2500 meters. The formation is：san d, sand-stone, shale cross.
主要目的油气层在2300到2500米，其地层岩性为：砂岩、砂
砾岩和泥岩互层。
2.17 No allowance for volume of hole enlargement.
不包括井眼扩大的泥浆体积。
2.18 Also not include the consumption for complex circumstance, such as blow-out, loss circ ulation etc.
也不包括井喷、井漏等复杂情况的材料消耗。
2.19 The mud volume estimated is based on 80% of efficiency of solids control equipment beha vior.
按固控设备清除效率80％计算本井的泥浆材料消耗量。
2.20 Actual Barite consumption will depend on hole condition while drilling.
实际的重晶石用量取决于井下的实际需要。
2.21 The annular volume is 115 cubic meters.
井眼的环空体积为115方。
PART 3. 配浆和处理 (Mixing And Treatment)
3.1 How many cubic meters high viscosity mud has you mixed?
高粘泥浆配了多少？
3.2 About 160 cubic meters.
大约160方。
3.3 Give me a hand, please!
请帮下忙！
3.4 Fill tanks with required amount of drilling water.
向泥浆池中加入需要量的钻井水。
3.5 Reduce calcium ion below 100 ppm by adding Soda Ash.
加入纯碱以降低钙离子浓度到低于100ppm。
3.6 Add 5 sacks DRISPAC and 10 sacks PF-FLO into the mud.
加五袋DRISPAC和十袋PF－FLO。
3.7 Addition of 0.5 to 1% PF-LUBE should be recommended to reduce any high torque or drag pr oblems
建议向泥浆中加入0.5~1%的PF-LUBE以降低扭矩和摩阻。
3.8 The mud should be pretreated with Bicarbonate while drilling cement.
当钻水泥塞时，应该用小苏打对泥浆进行预处理。
3.9 PF-TEMP are used to reduce API fluid loss less than 5 ml.
PF-TEMP用于将API失水降到低于5毫升。
3.10 Do you understand? Call the assistant driller (A.D.) or derrickmen down to help us.
明白了吗？叫副司钻或井架工下来帮忙。
3.11 The carrying capacity of the mud is lower, add 2~3 kg/m3 DRISPAC.
泥浆携砂能力下降，加入2～3公斤/方的DRISPAC。
3.12 For the mud system, maintain pH values among 8.5 to 9.5 while drilling.
对于这套泥浆体系，钻进期间应维持泥浆的pH值在8.5~9.5之
间。
3.13 Add adequate PF-THIN to reduce the viscosity and gels of the mud.
加入适量的PF－THIN，以降低泥浆的粘度和切力。
3.14 Add PF-GLA for raise the resist caving capacity and lubricity.
加入PF－GLA以增强泥浆的防塌润滑性能。
3.15 The last section抯 mud can be used in this interval.
上一井段的泥浆可以混入本段新浆中使用。
3.16 Let’s go to transform the mud to PEM system.
去将本段泥浆转化成PEM泥浆体系。
3.17 Must keep the concentration of PF-PLUS over 2.85 kg/m3 in mud.
应保持泥浆中PF－PLUS的最小浓度为2.85公斤/方。
3.18 Do not stop the agitator.
别关(泥浆池的)搅拌器。
PART 4. 钻井工程A (Drilling Engineering A)
4.1 The pressure test is O.K.
试压合格。
4.2 Run the wear bushing.
下抗磨补心。
4.3 Stop the pumps for a flow check.
停泵观察。
4.4 Make a wiper trip to the 20 inch casing shoe.
短起下到20英寸套管鞋。
4.5 Ream down all the tight points.
在所有遇阻点进行划眼。
4.6 Work the string up and down.
上下活动钻具。
4.7 Make a short trip.
进行短起下钻。
4.8 Slug the pipe.
灌重泥浆。
4.9 Circulate bottoms up for a sample.
循环取样观察。
4.10 Circulate the hole clean.
循环清洗井眼。
4.11 Drill the 36” hole with seawater, pumping 4~6 cubic meters high viscosity slugs for o ne string.
在36英寸井眼用海水钻进，每钻一个立拄泵入4～6方的稠泥浆进行清扫。
4.12 When 20” casing depth is attained, displace hole volume with hig h viscosity mud.
钻达20英寸套管深度时，用高粘度泥浆替满井眼。
4.13 When logging or general overhaul for long time, mud density
must be raised to E.C.D. for stable of hole.
在电测或长时间停钻检修设备时，将泥浆密度提高到循环时的当量泥浆密度范围。
4.14 Drilling with cone (drag) bit in the section.
此段地层采用牙轮（刮刀）钻头钻进。
4.15 Running (landing, pulling) casing.
下（起）套管。
PART 5. 钻井工程B (Drilling Engineering B)
5.1 Do not dump the mud into the sea.
不要把泥浆排放到海里。
5.2 Slug the pipe with two cubic meters of mud before pulling out.
起钻前打进两方重泥浆。
5.3 This is the undergauged (tight hole) interval.
这是缩径井段。
5.4 The bit must have been balled up, must it not?
钻头泥包了，是吗？
5.5 Stop drilling at 2965 meters.
钻至2965米，停钻。
5.6 Get ready to drop a TOTCO (deviation survey) once the circulation has finished.
循环结束，准备投测。
5.7 How long is it to circulate bottoms up?
需要循环多长时间？
5.8 Circulate for one and a half hour and then pull the string out at 14:30.
循环一个半钟头，14:30起钻。
5.9 The penetration rate (ROP) has been
6.18 meters per hour.
机械钻速为6.18米/小时。
5.10 Drill cement with seawater and then displace the new mud into the hole as drilling ou t of the casing shoe.
用海水钻水泥塞，钻到套管鞋时替入泥浆。
5.11 The drill collar O.D. is 7.5 inch, and the drill pipe O.D. is 5 inch.
钻铤外径为7.5” ，钻杆外径为5敗￡
5.12 Collecting the drill cuttings at the shale-shaker.
到振动筛处取点钻屑来。
5.13 keep the mud flow characteristic in tubulant (hydraulic, laminar).
使泥浆流变性保持在紊流（揣流，层流）
5.14 Prevent the swabbing effect.
防止产生抽吸作用。
5.15 It is oil-base mud, which is water-in-oil emulsion。
这是油基泥浆，油包水泥浆。
5.16 Open the mud gun.
开动泥浆枪。
5.17 It is being in well survey.
正在电测。
5.18 W.O.C. now.
正在水泥候凝。
PART 6. 固相控制 (Solids Control)
6.1 Start the shale shaker.
启动振动筛。
6.2 Then start the desander and desilter.
然后启动除砂器和除泥器。
6.3 Shut off the degasser and centrifuge.
关掉除气器和离心机。
6.4 Change it with a 40 mesh screen.
换成40目筛布。
6.5 The actual mud density required will depend upan existing hole conditions. 实际的泥浆密度将取决于当时的井下情况。
6.6 The low gravity solid's content should be under 5% by volume in the mud. 要将泥浆中的低固相维持在5％(体积比)以下。
6.7 All solids control equipment should be run efficiently in drilling.
钻井时，所有的固相控制设备应该有效地运转。
6.8 The MBT of this system should be kept below 25 ppb.
应该将泥浆中的MBT值保持在低于25 ppb。
6.9 Adding 20 tons Barite to raise mud weight of this pit to the 1.20 S.G.
加20吨重晶石将这池泥浆的密度提到1.20 S.G.。
6.10 Clean the settling pits. (Dump the sand trap.)
清洗沉砂池。
PART 7. 井下复杂情况A (Complex Circumstance A)
7.1 The down-hole problems are very complicated.
井下情况很复杂。
7.2 We have gotten overpull while tripping out.
起钻遇卡。
7.3 The hole is tight while running in.
下钻遇阻。
7.4 The formation is unstable and the well caving are serve.
地层不稳定，井塌严重。
7.5 There are no mud returns while circulating.
循环时没有泥浆返出。
7.6 The pit level has lowered quickly.
泥浆池液面下降很快。
7.7 The hole lost returns.
有进无出。
7.8 Where is the thief zone?
漏失层在哪里？
7.9 Pump(Spot) the lost circulation materials (L.C.M.) into the hole.
打堵漏泥浆。
7.10 The hole is kicking!
井涌啦！
7.11 It is loss circulation, stop drilling, circulation.
发生井漏，停止钻进，循环观察。
7.12 Trip up at once, pull the bit into the casing.
立即起钻，将钻头提到套管内。
7.13 L.C.M. has been added into the mud, tell the derrickmen to stop the shale shaker.
泥浆中已加入堵漏材料，叫甲板工关掉振动筛。
7.14 Using the seawater to force drill out the loss formation.
采用海水强行钻过漏失层。
7.15 The stuck-pipe soak fluids is: add 100 kg PIPE-LAX into the one cubic meter 0# diesel. 解卡液配方为：0号柴油一方加PIPE－LAX 100公斤。
PART 8. 井下复杂情况B (Complex Circumstance B)
8.1 Kill the well using the driller抯 method.
用司钻法压井。
8.2 Pump the 1.5 S.G. mud to kill the well.
泵入密度1.5的泥浆压井。
8.3 The hole conditions have been complicated by a combination of lost returns and the kic k.
又喷又漏，井下情况很复杂。
8.4 The pipe抯 stuck.
卡钻了。
8.5 Pump 10 cubic meters of diesel oil and free agents into the hole.
打进柴油和解卡剂10方。
8.6 The company has decided to plug the well for side tracking.
公司决定：打水泥塞侧钻。
8.7 Displace cement with the mud pumps!
用泥浆泵替水泥浆。
8.8 Pump the cement plug in the hole.
打水泥塞。
8.9 It is the sweepage, add 10-30 kg/m3 PF-SEAL(fine fiber) in whole circulating mud.
发生渗漏，在循环泥浆中加入10～30 公斤/方的PF-SEAL。
8.10 Adjust mud properties at once.
立即调整泥浆性能。
PART 9. 泥浆房试验 (Testing In Mud Room)
9.1 Checking the mud test equipment in the pilot test kit.
检查仪器箱中的泥浆试验设备。
9.2 Use the mud balance to determinate the mud weight.
用泥浆比重计测出泥浆的密度。
9.3 The Marsh Funnel (Viscometer) is used for routine viscosity determinations.
马氏漏斗用作日常泥浆浓度的测定。
9.4 The Six-speed Electronic Rheometer is made up from BAROID.
这台六速流变仪是贝劳德公司制造的。
9.5 For this mud sample, PV is 20, YP is 15, and fluid loss is 6 ml.
测这个泥浆样品，PV为20， YP为15，失水是6毫升。
9.6 Get the mud sample under the shale-shaker.
在振动筛处取样。
9.7 Sand content is below 1%.
含砂量小于1％。
9.8 The pH value is 8.5 by pH indicator strips.
用pH试纸测得泥浆pH为8.5。
9.9 The chemical analysis result are:
Ca2+ =400, Cl- =18000, Pm=1.5, Pf=0.3, Mf=0.4
泥浆化学分析结果为： Ca2+ =400，Pm=18000，Pf=0.3，
Mf=0.4。
9.10 Do you bring the Retort Kit, Methylene Blue Kit to the platform?
你带了固相蒸馏仪和亚甲基蓝测试仪到平台上吗？
9.11 Have a fluorescence analysis for the mud sample.
对泥浆样品进行荧光分析。
PART 10. 完井作业 (Completion)
10.1 Adding 1-2% of PF-BPA should be commenced before entering pay zone to minimize formati on damage.
进入油层前就在泥浆中加入1～2％的PF－BPA，以减少地层的损
害。
10.2 CA-101 is used to provide corrosion protection in free-solids brine.
CA－101用于无固相盐水完井液中起腐蚀抑制作用。
10.3 Let抯 prepare the completion fluids.
让我们去准备完井液。
10.4 It is the packer fluids.
这池是封隔液。
10.5 Workover fluids is O.K.
修井液已配好。
10.6 The corrosion data must below 0.075 mm/year.
腐蚀速率必须低于0.075密尔/年。
10.7 After the well finish, only keep one mud engineer at the rig.
完钻后，只留一个泥浆工程师在井上。
10.8 Next prepare to test.
下一步准备试油。
10.9 The well would be abandoned, tell the derrickmen to clean the mud pits.
准备弃井，告诉甲板工去扫泥浆池
10.10 Finished drilling, prepare logging.
已完钻，准备电测。
PART 11. 作业安全 (Safety)
11.1 No smoking here!
这里不准吸烟！
11.2 Open flame is strictly prohibited.
严禁使用明火。
11.3 Put on your safety helmet(hard hat), please!
请戴上安全帽！
11.4 It抯 a dangerous area. Keep away from here!
这里危险，请离远点！
11.5 No way! That抯 against the rule.
不行！这是违章作业。
11.6 Sorry, drinking liquor is not allowed on the rig.
对不起，平台上不准喝酒。
11.7 Be careful at work!
工作时要小心！
11.8 The alarm was an abandon drill.
刚才的警报是弃船演习。
11.9 Man overboard! Help!
有人落水啦！救命！
11.10 Have you got the emergency programme?
有应急状态部署表吗？
PART 12. 泥浆处理剂 (Mud Materials)
12.1 Barite is one of the weighting materials. The density is about 4.2 S.G.
重晶石粉是加重材料的一种。其密度大约为4.2 S.G.
12.2 Use the XCD polymer as the viscosifier and fluid loss additives in mud.
在泥浆中用XCD生物聚合物作为提粘剂和降失水剂.
12.3 PF-THIN is a polymeric thinner, and normal using range is 5.0 - 10.0 ppb.
PF－THIN是一种聚合物稀释剂，其加量范围为5～10ppb。
12.4 For PETROTECH Drilling Fluids Service’ mud system, the toxicity data (EC50 values) is as follow.
对于中海石油技术服务泥浆公司的泥浆体系，请看以下的毒性
数据(EC50值)。
12.5 All materials used in the mud is no toxic.
泥浆中所用的泥浆材料都无毒。
12.6 The thermal stability of PF-TEX is over 200℃.
PF－TEX的热稳定性超过200℃。
12.7 For handling PF-TEX, contact with skin and eyes should be avoided.
使用PF－TEX时，要避免粘到皮肤上或溅到眼睛里。
12.8 PF-PLUS is packaged in 25 kg multi-ply paper bags.
PF－PLUS采用多层复合纸袋包装，每袋25公斤。
12.9 The product, which packaged with 200 kg drums, is PF-LUBE.
那个采用200公斤桶包装的泥浆材料是PF－LUBE。
12.10 No any spare place to store the other materials in the cabin.
泥浆舱里已经没有多余的地方存放其它的泥浆材料了。
PART 13. 泥浆报表 (Mud Report)
13.1 This is an API standard mud daily report.
这是一份API标准的泥浆日报表.
13.2 Provide today抯 mud daily report to the operator before 24:00.
在今晚12点之前将今天的泥浆日报表交给钻井监督.
13.3 At the end of the well we must provide operator with a detailed review of the mud engi neering operations performed.
完井时我们要向作业者提供一份详细的泥浆工程作业完成报
告。
13.4 Using the portable computer to finish this Mud Recap.
用笔记本电脑将这份泥浆完井报告完成.
13.5 Four copies are required. Keep one for yourself, another one for operator, one for ri
g and one for mud base.
需要一式四份。自己留一份，一份交作业者，一份给平台，另
一份带回泥浆基地。
13.6 The mud materials consumption of this interval were listed in here.
本井段的泥浆材料消耗情况列在这里。
13.7 Total mud cost of the well is 530,780 yuan RMB.
这口井的泥浆总费用为530,780元人民币。
13.8 The treatment volume for mud treatment in this section is 460 cubic meters.
本段总的泥浆处理体积为460方。
13.9 It is the brief mud properties for the 12 1/4 inch interval.
这是12 1/4英寸井段的主要泥浆性能。
13.10 After that is the mud cost analysis and problem's discussion.
接下来是泥浆费用分析和问题讨论。
13.11 Please write the “Drilling Fluids Engineering Accident Report”.
请填写“钻井液事故报告”。
13.12 Let the Drilling Supervisor sign the “Drilling Fluids Service Sheet”, a nd take it ba ck to the Base Manager.
请钻井监督填“泥浆服务签单”，并带回给基地经理。
13.13 This is the list of materials just came.
这是刚到的泥浆材料清单。
PART 14. 公司介绍 (Service Introduction)
14.1 I am working for PETROTECH Drilling Fluids Service.
我为中海石油技术服务泥浆公司工作。
14.2 PETROTECH Drilling Fluids Service is a division of PETROTECH SERVICES, CNOOC.
中海技服泥浆公司是中海石油技术服务公司下的一个专业服务
公司。
14.3 We provides drilling fluids engineering services both offshore and onshore.
我们为海上和陆地钻井上提供钻井液工程技术服务。
14.4 We also supplies additives for drilling.
我们也为钻井提供泥浆材料。
14.5 Our Service has warehouses in Zhanjiang Base and Tanggu Base.
我们公司在湛江和塘沽基地都有泥浆材料库房。
14.6 We are able to provide various products for following mud systems.
我们能够为以下的泥浆体系提供各种处理剂。
14.7 How many people in your Service?
你们公司有多少人？
14.8 Eighty-two staffs, now. Eight of them are senior engineers.
现在有82人。其中八人是高级工程师。
14.9 Drilling Fluids Service formed a joint venture CHINA-NANHAI Magcobar Mud Corporation L imited with M-I in 1984.
泥浆公司与美国M－I公司在1984年成立了中国－南海麦克巴泥浆有限合营公司。
14.10 We provide ten employees for the CHINA-NANHAI Magcobar Company this year.
我们今年为麦克巴合营公司提供10名雇员。
14.11 Several mud materials are imported. These materials, which are made in CHINA, are pr ovided by our Service
那几种材料是进口的，这些材料是我们公司提供的国产材料。
石油钻井英语词汇
对照实物确认的钻井词汇 一、井口与井控 1.套管头升高短节（上下由法兰连接，中间是三通或四通）casing spool 2.油管悬挂器tubing hanger 3.油管悬挂器上边接有阀门的盖子tubing bonnet 4.（可焊接的）导管头（接箍）conductor connector 5.（可焊接的）套管头（接箍）casing connector 6.井口帽blanking cap & plug 7.三闸板防喷器triple slide-lok preventer 8.双闸板防喷器double slide-lok prevente 9.油/套管升高短节tubing/casing riser 10.整体式升高短节integral union riser 11.法兰×丝扣井口转换头wellhead adapter 12.井口四通两边的横向阀门wing valves 13.油管悬挂器上边的变径法兰大小头bonnet 14.上边是法兰的套管头casing flange 15.只上边是法兰，下边与表层套管焊接的套管头casing head 16.套管头内的卡瓦casing slips 17.（上法兰小，下法兰大）变径套管头casing spool crossover 18.与导管焊接的坐在圆井底的套管头landing head flange top 19.卡瓦密封套管悬挂器slips seal casing hanger
20.（上下是法兰，中间是四通的）油管升高短节tubing spool 21.柔性封隔闸板flexpacker ram 22.可变径闸板variable bore ram 23.剪切闸板shearing blind ram 24.卡瓦型套管悬挂器slip-type casing hangers 25.高负荷悬挂器high-load hanger 26.悬挂器断开式密封圈hanger isolation seal ring 27.井口封隔变径变压法兰（中间有几道密封圈，下边是低压，上边是高压）packoff/crossover flange 28.油管头（下法兰大，内带密封圈；中间是四通，上法兰小）tubing heads 29.底（下）变径法兰（下边内径大，上边内径小）basic adapter 30.单密封变径法兰（下内径大，上内径小）single seal bore adapter 31.变径大小头（下边是法兰，上边是本体上钻孔攻丝扣）coupling adapter 32.油管悬挂器转换大小头短节（上法兰小，下法兰大，下法兰内有丝扣）tubingsuspension adapter 33.双油管悬挂器dual completion tubing hanger 34.双密封孔连接法兰dual seal bore adapter 35.锁紧螺丝lockdown screw 36.（地面）单油管密封总成single packer completion 37.法兰式采油树盖子flanged tree caps 38.扰性油管悬挂器coiled tubing hanger
钻井英语常用词汇及术语缩写.
API(America Petroleum Institute美国石油学会BHA(bottom hole assembelly井底钻具组合BHP(bottom hole pressure井底压力BOP control room远程控制台 BOP(blowout preventer防喷器 BTC(buttress thread connection梯形扣 CP(circulating pressure循环压力 DC(drill collar钻铤 DL(dogleg 狗腿 DLS(dogleg severity狗腿严重度DP(drill pipe钻杆 DST(drill stem test中途测试ECD(equivalent circulating density循环当量密度ECD(equivalent circulating density当量循环密度EF(external flush外平 EMW(equivalent mud weight当量泥浆密度EUE(external upset end内加厚 FCP(final circulating pressure终了循环压力FH(full hole贯眼扣 GPM(gallon per minute加仑每分HCR(hydraulic control remote valve液动阀 HP(hydrostatic pressure静液柱压力HWDP(heavy weight drillpipe加重钻杆 IADC(international association of drilling contractors钻井承包商 ID(inside diameter内径 IF(internal flush内平扣 KOP(kickoff point造斜点 LOT(leak off test漏失实验 LTC(long thread connection长园扣
常用钻井英语缩写
钻井英语缩写 1.DP drill pipe 钻杆 2.HWDP heavy weight (wall) drill pipe 加重钻杆 3.DC drill collar 钻铤 4.BHA bottom hole assembly 井下钻具组合 5.STB stabilizer 钻杆扶正器 6.PNMDC pony non-magnetic drill collar 短无磁钻铤 7.SMDC short non-magnetic drill collar 短无磁钻铤 8.PDM positive displacement motor 螺杆9.BOP blowout preventer 封井器 10.BOPE blow out preventer equipment 封井器设备 11.IBOP inside blowout preventer 内防喷工具 12.CSG casing 套管 13.TBG tubing 油管
14.JNT/JT joint 单根 15.XO cross-over 配合接头 16.IF internal flush 内平 17.FH full hole 贯眼 18.REG regular 正规 19.IU internal upset 内加厚 20.EU external upset 外加厚 21.EUE external upset 外加厚 22.IEU internal＆external upset 内外加厚 23.OH open hole 裸眼 24.WOB weight on bit 钻压 25.RPM revolutions per minute 转速/分钟 26.SPM strokes per minute 冲程/每分钟 27.ECD equivalent circulating density 当量泥浆密度 28.MT metric ton 公制吨 29.DST drill stem test 钻
钻井英文词汇表
顶驱&钻井英文常用词汇表 （第一版） 盘锦辽河油田天意石油装备有限公司 2010年9月
一、顶驱英文 顶部驱动系统Top drive system 车载钻机truck-mounted rig 机械的mechanical 电学的electrical 液压的hydraulic 钻井设备drilling equipment 大斜度井high-inclination well 深井deep well 丛式定向钻井cluster directional well 低温顶驱low-temperature top drive system 超深井ultra-deep well 定向井directional well 载荷load capacity 工作高度working height 电动机motor 功率power 转速rotary speed 钻井扭矩drilling torque 过载能力over load capacity 卸扣break out 上扣make-up 循环压力circulation pressure 额定压力rated pressure 电源电压power voltage 电源频率power frequency 工作电流working current 通风机ventilator 接线箱junction box 平衡油缸counterbalance cylinder 盘式刹车disc brake 电缆接插件cable connector assembly 主电机main motor 液压阀组hydraulic valve block 提环bail 鹅颈管gooseneck 油箱tank 蓄能器accumulator 齿轮箱gearbox 冲管总成wash pipe assembly 液压马达hydraulic motor 回转头rotating head 导轨guide beam 倾斜油缸tilt cylinder 防松法兰lock flange 背钳back-up tong 导向器stabbing guide 遥控IBOP upper IBOP 手动IBOP lower IBOP 吊环link 吊卡elevator 齿轮轴gear shaft 冷却风机Cooling motor 交流电机 AC motor 水龙头 Swivel 主齿轮 Driving gear 编码器 Encoder 散热器 Radiator 油道 Oil passage 密封槽Seal groove 轴承 bearing 滚轮 Roller 滑套 IBOP actuator shell 曲柄 Crank 销pin 钳牙tongdies 活塞piston 螺栓bolt 黄油grease 小车总成 Carriage accessory 气流 Air current 风道 Air duct 进风口 Air inlet 出风口 Air outlet 梨型环 Pear link 卡箍clamping band 键key
钻井现场常用英语专业词汇
Accumulator 储能器 Active tank 循环池 Adjusting bolt （刹把）调节螺栓Admission pipe 进气管 Agitator 搅拌器 Air chamber 空气包 Air line 气管线 Air-operated hoist 气动绞车Alternating current drive 交流电驱动Annular BOP 环形BOP Ato-muffler 消音器 Ball valve 球阀 Bell nipple 井口喇叭管 Bench vise 老虎钳 bit breaker 钻头装卸器 bit gauge 钻头规 blind ram preventer 盲板防喷器BOP control panel 防喷器控制盘BOP deck 防喷器平台 Bottom plug 底塞 Brake lever (brake handle) 刹把Brake line (brake staple) 刹带Bridge plug 桥塞 Buttress 梯形扣 Butterfly valve 蝶阀 By-pass 旁通 By-pass plug 旁通塞 Calipers 卡钳 Casing coupling 套管接箍 Casing cutter 套管割刀 Casing elevator 套管吊卡 Casing hanger 套管悬挂器 Casing head 套管头 Casing monkey board 套管平台Casing scraper 刮管器 Casing shoe 套管鞋 Casing slip 套管卡瓦 Casing spear 套管打捞矛 Casing spool 套管四通 Casing tong 套管大钳 Cat line 猫头绳 Cat line grip 猫头绳爪 Cat shaft 猫头轴 Cat-head 猫头 Cellar deck 井口甲板Cement 水泥 Cement basket 水泥伞 Cement plug 水泥塞 Cement retainer 水泥阻流环 Cementing bond log 固井质量检查Cementing head 水泥头 Cementing line 固井管线 Cementing pump 固井泵 Chain 链 Chain pipe tong 链钳 Chain tong 链钳 Chamber 房间，寝室 Chamber gate 阀箱，闸室 Charge pump 灌注泵 Check valve 止回阀，回压凡尔 Choke 节流器，阻流器 Choke line 阻流管线 Choke position indicator 节流阀位置指示器Choke valve 节流阀 Choke-line manifold 阻流管汇 Clutch 离合器 Conductor 导管 Cone 牙轮 Cone fisher 牙轮打捞器 Cone lock 牙轮卡死 Cooling-water pump 冷却水泵 Core barrel shoe 取心筒鞋 Core basket 取心爪 Core bit 取心钻头 Core catcher 取心爪 Core catch case 取心爪外套 Core drying oven 岩心烘箱 Crossover joint(x/o) 变换接头 Crown block 天车 Crown block beam 天车梁 Dead line 死绳 Dead line diaphragm 死绳固定器膜片Dead line anchor 死绳固定器 Degasser 除气器 Derrick 井架 Desander (desilter) 除砂器（除泥器）Direct current drive 直流电驱动Discharge line 排除管线 Double ram type preventer 双闸板防喷器Down hole tool 入井工具
钻井英语简写
钻井英语缩写 Abbreviation DP Drill pipe 钻杆 HWDP heavy weight drill pipe 加重钻杆 DC drill collar 钻铤 STB stabilizer 钻杆扶正器 SMDC short magnetic drill collar 短无磁钻铤PDM positive displacement motor 螺杆 NMDC nonmagnetic drill collar 无磁钻铤（钻具）BOP blowout preventer 封井器 CSC casing 套管 JNT joint 单根 XO cross-over 配合接头 IF internal flush 内平 FH full hole 贯眼 REG regular 正规 IU internal upset 内加厚 EU external upset 外加厚 IEU internal & external upset 内外加厚 OH open hole 裸眼 WOB weight on bit 钻压 RPM revolutions per minute 转速分钟 SPM strokes per minute 冲程每分钟 ECD equivalent circulating density 当量泥浆密度MT metric ton 公制吨 BHA bottom hole assembly 底部钻具组合 DST drill stem test 钻具测试 KS key seat 键槽 STDS stands 立柱 VIS viscosity 粘度 WL water loss 失水 PV plastic viscosity 塑性粘度 YP yield point 屈服值 FL filtrate loss 滤失 TVD true vertical depth 垂深 MD measured depth 测量井深 TD total depth 总井深 KOP kick off point 造斜点 DIR direction 定向 AZM azimuth 方位 DEV deviation 井斜 ROP rate of penetration 机械钻速 ID inside-diameter 外径
(完整版)石油钻井工程英语词汇
地址：北京市朝阳区东三环中路7号财富中心A 座601 邮编：100020 石 油 钻 井 工 程 英 语 词 汇 2008-10-15 第一章：石油钻井工程英语基础词汇 第1 节 石油钻井工程基础词汇 钻井：drill 定向斜井：directional drilling 欠平衡钻井：under-balance drilling 海上钻井：off-shore drilling 陆地钻井： on-shore drilling 钻头：drill bit 刮刀钻头：drag bit 牙轮钻头：rock bit (镶齿钻头insert bit, 钢齿钻头steel toothed bit) 金刚石钻头：diamond bit 取心钻头：coring bit 钻头浮阀：float valve 钻头水眼：bit nozzle(or jet) 钻头水眼刺:bit nozzle washed out 钻头规：bit caliper(bit gauge) 钻头泥包：bit is balling 钻头钝了，我建议现在起钻：bit is dull. I suggest to POOH now
钻铤：DC(drill collar ) 光钻铤slick drill collar， 螺旋钻铤spiral drill collar 钻杆：DP(drill pipe ) 方钻杆：kelly 公扣：pin end 母扣：box end 内平式连接：IF(internal flash) 正规式连接：REG(regular) 贯眼式连接：FH(full hole)加重钻杆heavy weight drill pipe 短钻杆pop joint 井下马达：downhole motor 涡轮钻具：turbine 震击器：drilling jar 减震器：absorber 下部钻具组合：BHA（bottom hole assembly） 钻具扶正器：stabilizer（string stabilizer, near-bit stabilizer） 钻机：drill rig 钻井泥浆：drilling mud 钻井液：drilling fluid 钻井设备：drilling equipment油：oil 原油：crude oil 天然气：nature gas 煤层气：coal-bed gas 石油：petroleum 中国石油（简称）：CNPC（China National Petroleum Corporation ）长城钻井（简称）：GWDC(Great Wall Drilling Company) 采油：oil production 产油层(目的层)：reservoir( or pay zone) 钻进：drilling 调整钻井参数以得到理想的机械钻速： play the drilling parameters to get fast ROP 起钻：POOH(pull out of hole) 下钻：RIH(run in hole) 下套管：run casing(or RIH with casing) 短起下钻：wiper trip 循环泥浆：circulate 泥浆：reverse circulate 中途循环泥浆：break circulation 分段下钻：RIH in stages 通井：control trip 划眼：reaming 倒划眼：back reaming
石油钻井专业英语词汇
目录 第一节钻井英语单词 (2) 第二节井场用语，钻井常用短语及句子 (10) 第三节钻井泥浆术语 (29) 第四节常用安全术语 (31) 第五节钻井设备英语 (33) 第六节石油钻井英语情景会话 (40) 附录一：平台人员、作业者及服务公司人员名称 (47) 附录二：主要设备名称 (48) 附录三：钻具、井口工具、打捞工具名称 (52) 附录四：材料和工具名称 (53) 附录五：常用缩写形式 (55)
第一节钻井英语单词 drilling crew 钻井队 drill floor,rig floor,floor 钻台drawworks 绞车 well-site, rig-site 井场 rig manager 平台经理 DC (drill collar) 钻铤 drilling engineer 钻井工程师 DP (drill pipe) 钻杆 toolpusher 带班队长 rotary table 转盘 driller 司钻 assistant driller 副司钻derrickman, monkeyman 井架工roughneck, floorman 钻工roustabout 场地工 liner 缸套 motor fire man 司机（motorman）wellhead 井口 circulation & solid system 循环固控系统 machinist 机械师,机工,机械大班electrician 电器师,电工,电器大班operation program 作业程序(指令) cathead 猫头 caravan 营房，大篷车 tong 大钳 elevator 吊卡 well depth 井深 slip 卡瓦makeup 上扣 spud in 开钻 breakout 卸扣 ROP (rate of penetration),drilling speed, penetration rate 钻速 trip 起下钻 diesel-engine 柴油机 loss circulation 井漏，循环漏失working uniform 工作服 brake handle, brake bar 刹把 water well condition 水井井况circulating tank, circulation tank 循环罐 normal drilling 正常钻进 reserve tank 储备罐 parameter 参数 trip tank 补给罐，尖底罐, 起下钻泥浆罐（起下钻计量罐） rotary speed 转盘转速（转速）shale shaker 振动筛 pump pressure 泵压 WOB (weight on bit) 钻压 mesh 目,网孔;啮合,编织 torque 扭矩 screen cloth 筛布 displacement 排量 safety meeting 班前会 pump stroke 泵冲 shift exchange 交班、（倒班）
海洋石油常用中英文对照词汇
A A-60 fire door A-60级防火门 a-hundred-year return period 百年一遇abrasive （喷砂用的）磨料abrasive paper 砂纸 AC generator 交流发电机 AC motor 交流电动机accelerated corrosion testing 加速腐蚀试验acceptance criteria 合格准则 access hole (for welding) = cope hole (焊接)工艺孔accommodation and power platform (APP) 生活动力平台according to = in accordance with = in line with = as per = in the light of 按照 acetylene gas 乙炔 acid electrode 酸性焊条 acid proof cement 防酸水泥additive 添加剂 adhere to 遵守（动词）adherence to 遵守（名词）adjacent columns 相邻立柱adverse combination of loads 载荷的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction) 建造批准aforementioned 上述 aft winch 船艉绞车agitator 搅拌器 air blower 鼓风机 air compressor 空气压缩机 air driven pump 气动泵 air hoister 气动绞车 air manifold 气包 air tight test 气密性试验 air-hose 风带 aircraft obstruction beacon 航空障碍灯alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨脂漆allowable (working) stress 许用应力Aluminum alloy anode 铝合金阳极Aluminum ingot 铝锭aluminum paint 银粉漆aluminum sheet 铝皮 ambient air temperature 环境气温ambient temperature 环境温度
常用钻井英语缩写
标准文档 钻井英语缩写motor 螺杆 9.BOP blowout preventer 1.DP drill pipe 钻杆封井器HWDP heavy weight (wall) 2. 10.BOPE drill pipe 加重钻杆blow out preventer equipment 封井器设备3.DC drill collar 钻铤 11.IBOP inside blowout bottom 4.BHA hole assembly 井下钻具组合内防喷工具preventer 套管casing 12. 5.STB stabilizer 钻杆扶正器CSG 油管non-magnetic pony tubing 13.TBG 6.PNMDC drill collar 单根JNT/JT 短无磁钻铤joint 14. 7.SMDC short 配合接头cross-over 15.non-magnetic XO drill collar 短无磁钻铤内平internal flush IF 16. 8.PDM 贯眼full hole displacement positive FH 17.实用大全． 标准文档 18.REG regular 正规27.ECD equivalent circulating
density 当量泥浆密度19.IU internal upset 内加厚 28.MT metric ton 公制吨20.EU external upset 外加厚29. DST drill stem test 外加21.EUE external upset 钻具测试厚 30.l22.IEU interna＆external KS key seat 键槽 31.KSW key seat wiper 内外加厚upset 键槽清洁器裸眼open hole OH 23. 32.STDS stands 钻压weight on bit WOB 24.立柱 33.VIS viscosity revolutions per minute RPM 25.粘度 塑性viscosity 34.PV 分钟/转速plastic strokes SPM 26. minute per 粘度冲程/屈服值yield point 每分钟YP 35.实用大全． 标准文档 36.FL filtrate loss 滤失45.AZM azimuth 方位 46.water loss 失水DEV deviation 井斜37.WL https://www.sodocs.net/doc/6514980257.html,D true vertical depth ROP rate of penetration 机械转速垂深 48.ID 测量inside-diameter 内径depth 39.MD measured 49.井深OD outside diameter 外径 50.FTG footage 40.TD total depth 总井深进尺 51. plug back total depth PPG pounds per gallon 41.PBTD 人工井底（密度）每加仑磅inch pounds per square 52. piece
石油钻井英语
行业英语之实用词汇
现场实用词汇短语 一、甲方乙方 1. 承包商人员 ( Contractor’s Personnel ) Equipment Supervisor 设备总监 Materials Supervisor 材料总监 Senior Toolpusher 高级队长 Junior Toolpusher 值班队长 Driller 司钻 Sub Sea Engineer (SSE) 水下工程师 Assistant Driller (AD) 副司钻 Derrick Man 井架工 Floor Man (roughneck) 钻工 Crane Operator 吊车工 Mechanic 机械师 Electrician 电气师 Repairman 修理工 Welder 焊工 Radio Operator 电报员 Warehouse Man (stock Keeper) 材料员 Medic 医生 Safety Supervisor 安全监督
Interpreter (translator) 翻译 Chief Steward 管事 Cook 厨师 2、作业者及服务公司人员 ( Operator’s Personnel and Service Company Personnel) Drilling Superintendent 钻井监督 Company Man (Operator’s Representative) 公司代表 Geologist 地质师 Mud Logging Engineer (Mud logger) 泥浆录井工程师 Sample Catcher 捞砂工 Mud Engineer 泥浆工程师 ROV Engineer 潜水工程师 Cementer 固井工 Cement Engineer 固井工程师 Testing Engineer 试油工程师 Coring Engineer 取芯工程师 Wireline Logging Engineer电测工程师
最新钻井缩写大全
1.OH open hole裸眼 2.FH full hole 满眼，贯眼at full speed 3.AD assistant driller 副司钻 4.NTP （N toolpusher）night toolpusher夜班队长 5.RM reaming 划眼rig manager 平台经理 6.Back RM back ream倒划眼 7.CSG casing 套管 8.TBG tubing 油管coiled tubing 9.REG regular 常规扣at regular intervals regular meeting, irregular meeting 10.FTG footage 进尺 11.FPH footage per hour 每小时进尺 12.SNG single 单根 13.Hrs. hours 14.Yest. Yesterday 15.Fin. Finish 完成 16.OBS observe 观察 17.w/, t/, F/ with, to, from 18.XO crossover joint/sub 配合接头 19.BOP blowout preventer 防喷器 20.IBOP inner BOP 内防喷器 21.TDS Top drive system 顶驱 22.TOF top of fish 鱼顶 23.HHP hydraulic horse power 水马力 B.HHP 24.Hi-vis high viscosity 高粘 25.RPM revolution per minute 转速 26.SPM strokes per minute泵冲数stroke length 27.ROP rate of penetration 机械钻速 https://www.sodocs.net/doc/6514980257.html,TV closed-circuit television 29.MWD measuring while drilling 随钻测量 30.DP drill pipe 钻杆 31.HWDP heavy wall/weight drill pipe 加重钻杆 32.DC drill collar 钻铤 33.NMDC non-magnetic drill collar 无磁钻铤 34.STB stabilizer 扶正器 35.JNT joint 单根 36.IF internal flush 内平扣 Internal-external inner-outer inside-outside Input-output entrance-exit inlet-outlet Indoors-outdoors Increase- decrease raise-lower upper-lower 37.IU internal upset 内加厚 38.EU external upset 外加厚 39.IEU internal & external upset 内外加厚 40.WOB weight on bit 钻压bit load
石油英语(中海油员工手册)
A A-60 fire door A－60级防火门Abrasive (喷砂用的)磨料abrasive paper 砂纸 AC generator 交流发电机AC motor 交流电动机Accelerated corrosion testing 加速腐蚀试验Acceptance criteria 合格准则access hole (for welding)= cope hole (焊接)工艺孔accommodation and power platform (APP) 生活动力平台 according to = in accordance with = in line with = as per = in the light of 按照acetylene gas 乙炔 acid electrode 酸性焊条 acid proof cement 防酸水泥Additive 添加剂adhere to 遵守(动词) Adherence to 遵守(名词) adjacent columns 相邻立柱adverse combination of loads 荷载的不利组合adverse condition 不利条件aeronautical radio system 航空无线电系统AFC (approved for construction)建造批准aforementioned 上述的 aft winch 船艉绞车Agitator 搅拌器 a-hundred-year return period 百年一遇 air blower 鼓风机 air compressor 空压机 air driven pump 气动泵 air hoister 气动绞车 air manifold 气包 air tight test 气密性试验aircraft obstruction beacon 航空障碍灯air-hose 风带 alarm buzzer 报警蜂鸣器alarm horn 报警喇叭aliphatic polyurethane 脂肪族聚氨酯漆Allowable(working) stress 许用应力Aluminum alloy anode 铝合金阳极 一. 技术词汇
钻井英语缩写
Abbreviation DP Drill pipe 钻杆 HWDP heavy weight drill pipe 加重钻杆 DC drill collar 钻铤 STB stabilizer 钻杆扶正器 SMDC short magnetic drill collar 短无磁钻铤PDM positive displacement motor 螺杆 NMDC nonmagnetic drill collar 无磁钻铤（钻具）BOP blowout preventer 封井器 CSC casing 套管 JNT joint 单根 XO cross-over 配合接头 IF internal flush 内平 FH full hole 贯眼 REG regular 正规 IU internal upset 内加厚 EU external upset 外加厚 IEU internal & external upset 内外加厚 OH open hole 裸眼 WOB weight on bit 钻压 RPM revolutions per minute 转速分钟 SPM strokes per minute 冲程每分钟
ECD equivalent circulating density 当量泥浆密度MT metric ton 公制吨 BHA bottom hole assembly 底部钻具组合 DST drill stem test 钻具测试 KS key seat 键槽 STDS stands 立柱 VIS viscosity 粘度 WL water loss 失水 PV plastic viscosity 塑性粘度 YP yield point 屈服值 FL filtrate loss 滤失 TVD true vertical depth 垂深 MD measured depth 测量井深 TD total depth 总井深 KOP kick off point 造斜点 DIR direction 定向 AZM azimuth 方位 DEV deviation 井斜 ROP rate of penetration 机械钻速 ID inside-diameter 外径 FTG footage 进尺 PPG pounds per gallon （密度）每加仑磅
海外钻井项目必备词汇REVISED
海外钻井项目必备英语词汇ESSENTIAL ENGLISH WORDS FOR OVERSEAS DRILLING PROJECTS 山东胜利职业学院 国际化人才培训部
目录 第一章：石油钻井工程英语基础词汇 第1节石油钻井工程基础词汇 (1) 第2节石油钻井方法基础词汇 (5) 第3节石油钻井技术基础词汇 (5) 第4节石油钻井参数基础词汇 (6) 第5节石油钻井作业现场工作人员名称 (7) 第 6 节石油作业现场常用工具 (8) 第二章：石油工程常用设备及专业术语 第1节钻井设备部分 (13) 第2节钻井泵类及相关设备 (16) 第3节与泵操作有关的实用短语 (18) 第4节钻台与底座 (19) 第5节井控操作与防喷器 (19) 第三章：钻井工程作业部分 第1节钻井事故 (24) 第2节钻头 (25) 第3节钻具 (25) 第4节钻井工程地面作业实用词汇与短语 (27) 第5节钻井工程井口作业实用词汇与短语 (28) 第四章：钻井液及相关设备 第1节钻井液名称 (30) 第2节钻井液设备 (31) 第3节钻井液处理剂 (31) 第五章：钻井相关作业 第1节取芯部分 (35) 第2节固井部分 (35) 第3节固井水泥浆名称和参数 (37) 第4节测井部分 (38) 第六章：井下作业常用短语 (39) 第七章：海上钻井作业 (41) 第八章：定向井部分 (42) 第九章：石油现场机械传动与机械设备 第1节：动力与传动 (43)
第十章：石油工程作业现场生活用词 第1节身体各部分名称 (45) 第2节服装 (47) 第3节描述天气 (49) 第4节常见蔬菜名称 (49) 第5节常见水果名称 (50) 第6节味道和调味品调味品 (50) 第7节酒类和祝酒 (51) 第8节食品 (52) 第9节超级市场 (53) 第10节容器、单位及钱币 (53) 第11节肉类 (54) 第12节海鲜，鱼类 (54) 第13节救火及救援 (55) 第14节日常生活用品 (55) 第15节星期与月份 (56) 第16节数字 (57) 第17节颜色 (58) 第十一章：常用缩略语与换算 第1节常用缩略语 Abbreviation (59) 第2节钻井现场常用公英制（美国用法）换算 (60)
石油钻井英语
石油钻井英语 A Handbook of English for Offshore Oil Drilling 海洋石油钻井常用英语手册 Drilling 钻井 Carry out drilling operation in accordance with the drilling program. 按钻井程序进行钻井作业. Prepared bell nipple. 准备”喇叭口”短节. Make up 2 joints of drill pipe. 接两根钻杆. Break out this connection. 卸开该接头. Run hole opener to sea bed. 下扩眼器到海底 Mix gel fluid for drilling conductor hole. 为钻导管井眼配制高粘度泥浆. Make up bottom hole assembly. 组合下部钻具 Check and reset crown-saver on every tour. 每个班都要检查并重新调整天车防碰装置. Number stands on trip out and trip in. 起下钻时给立柱编号. Pick up BHA and run to seafloor. 将下部钻具下到海底. Pick up stands. 接立柱 Don’t drill faster than 15 minutes for 1 stand. 钻进速度别超过15分钟1根立柱 Drop TOTCO. 投(陶特)测斜仪 Fish TOTCO with overshot. 用打捞筒捞起测斜仪 Resume drilling to T.D. 继续钻进到总深 Circulate 15 minutes.循环15分钟 Run in hole. 下钻 Put out of hole. 起钻 Make an inventory of all ring gaskets. 开一个所有垫圈的清单 Use spinning tong. 使用气动扳手 Operate the air winch. 操作气动绞车 Lay down 57 joints of 5” drill pipe. 甩57根钻杆 Pick up drill stem test tool. 提起钻杆测试工具 Circulate mud for 2 hours. 循环泥浆2小时 Move string during circulation. 在循环时注意活动钻具 Circulate hole clean. 循环清洗井眼