主要缺陷中英文对照
德仕科技（深圳）有限公司
品管部中英文对照表（一）
主要缺陷中英文对照
主要测量仪器中英文对照
电子电器产品不良缺陷对应英文描述
General Defect - 通用电器缺陷 cord untied or irregularly tied电线未绑或绑的不规则exposed wires金属线外露 brass wire in power cord exposed电源线的铜丝外露ground wire discontinuous地线间断 burn down烧坏 jam刮／卡死 excessive noise噪音过多 shock noise振动有噪音 switch operated not smoothly开关不顺 polarity reversed极性接反 open circuited开路 short circuited短路 grounding continuity test failed接地失败 Hi-pot test failed高压失败 leakage current test failed漏电 power supply dead无电源 dielectric strength test failed介质强度测试失败current or wattage out of specification电流／电压不合规格live wire exposed火线外露 General location - 电器通用缺陷 位置 jack插口 AC-IN jack交流输入口 DC-IN jack直流输入口 socket插座 socket cover插座盖 plug插头 plug foot插脚 polarized plug极性插头 coupling plug转化／耦合插头 flat blade plug扁脚插头 channel频道 function key功能键 nut螺母 LCD液晶显示屏 power LED indicator电源电子指示灯power cord电源线 electrode plate电极片 ON-Off switch开关 adapter适配器
主要缺陷中英文对照
主要缺陷中英文对照
————————————————————————————————作者：————————————————————————————————日期： 2
德仕科技（深圳）有限公司 品管部中英文对照表（一） 主要缺陷中英文对照 序号中文英文 序 号 中文英文 1 披峰Flash 16 流痕Flow mark 2 走不齐/ 缺胶 Short shot 17 色差 abberration 3 变形/注塑 后变形 Deformation 18 夹水线Weld lines 4 偏模Mismatch 19 碰伤Bump damage 5 起泡Blister 20 银线Silver 6 污斑Grease pits 21 少数量Packing shortage 7 雾化Atomization 22 泛白Blushing 8 烧焦Burn mark 23 发白Whitening 9 油污Oil mark 24 刮伤Scratch 10 气泡Blister 25 气纹Gas lines 11 划痕Scffing 26 混色Color mixture 12 泛黄Yellowing 27 斑点/污 点/ 黑点 Macula 13 缩水Sink mark 28 结合线 14 段差29 拉伤Pull 15 抛光不良Polishing mark 30 水印Watermark 主要测量仪器中英文对照
序号中文英文 序 号 中文英文 1 分厘卡(千 分尺) Micrometer 14 卡尺Caliper 2 C表Dial gauge 15 扁分厘卡Blade micrometer 3 块规Block gauge 16 针规Pin gauge 4 CMM X-Y-Z Coordinate 17 电子卡尺Digital caliper 5 扭力计Torque meter 18 投影仪Projection apparatus 6 高度仪Height gauge 19 直角尺Square master 7 游标卡尺Vernier caliper 20 硬度机Durometer 8 牙规Scre gauge 21 半径规Radius gauge 9 角度规Universal protractor 22 特别塞规Ring gauge 10 拉/推力计Pull/Push gauge 23 弹力计Spring balance 11 塞尺Clearance gauge 24 专用夹具Special fixture 12 工具显微 镜 Tool-measuring microscope 25 千分表Dial indicator 13 1 抽样Sampling 11 抽样计划 Sampling plan 2 样品数量Sample size 12 合格Conformity
焊接缺陷中英文对照
精心整理 焊接缺陷 1. 裂缝：crack （焊缝/弧坑/热影响区裂纹:weldmetal/crater/heat-affectedZone(HAZ)crack ） 2. 焊瘤:overlap 3. 冷隔：coldlap 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 塌陷:excessivepenetration 16. 凹坑:pit/dent 17. 过度打磨：excessivegrinding 18. 焊疤：scar 19. 飞溅：spatter
20.焊缝成行不好：poorprofile 21.焊角不足：lackofweldleg 附录attachment 焊接工艺方法 1.熔焊:fusionwelding压焊:pressurewelding钎焊:brazingwelding 2.焊缝倾角:weldslope,inclinationofweldaxis. 3.焊缝转角:weldrotation,angleofrotation 4.平焊 5.立焊 6. 7. 8. 9. 10. 11. 12. 13. 14.I 15.Y 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.堆焊 29.衬垫焊:weldingwithbacking. 30.焊剂垫焊:weldingwithfluxbacking 31.电弧点焊:arcspotwelding. 32.套环:ferrule试板testpiece随机检查randomcheck 33.单面/双面串联点焊:direct/indirectserialspotswelding. 34.机械性能试验mechanicalpropertiestest 35.简历curriculumvitae 36.分类category 37.风险评估riskassessment 38.第三方notifiedbody 39.基准modules
焊接缺陷中英文对照
焊接缺陷1.裂缝：crack （焊缝/弧坑/热影响区裂纹:weld metal/crater/ heat-affected Zone (HAZ) crack） 2.焊瘤:overlap 3.冷隔：cold lap 4.未焊满: under fill / incompletely filled groove 5.咬边: undercut 6.道间没有圆滑过渡/焊缝凹陷：bum effect / Excessive concave 7.未溶合: lack of fusion / incomplete fusion 8.气孔:gas pore / blowhole (针尖状气孔:pinhole; 密集气 孔:porosity; 条虫状气孔:wormhole) 9.夹渣: slag inclusion (夹钨:tungsten inclusion; 夹杂 物:inclusion) 10.未焊透:incomplete penetration / lack of penetration 11.过度焊缝加强高：excessive reinforce / Excessive weld metal 12.电弧烧伤：Arc strike / Arc burn 13.焊接变形: welding deformation 14.烧穿:burn through 15.塌陷: excessive penetration 16.凹坑:pit / dent 17.过度打磨：excessive grinding
scar 焊疤：18. 19.飞溅：spatter 20.焊缝成行不好：poor profile 21.焊角不足：lack of weld leg 附录 attachment 焊接工艺方法 1.熔焊:fusion welding 压焊:pressure welding 钎焊:brazing welding 2.焊缝倾角:weld slope, inclination of weld axis. 3.焊缝转角:weld rotation, angle of rotation 4.平焊:flat position of welding, downhand welding 横焊:Horizontal position welding. 5.立焊:vertical position welding 仰焊:overhead position welding. 6.向下立焊:vertical down welding, downward welding in the vertical position. 7.向上立焊:vertical up welding, upward welding in the vertical position. 8.倾斜焊;inclined position welding 9.上坡焊: upward welding in the inclined position 10.下坡焊: downward welding in the inclined position 11.对接焊:butt welding 角焊:fillet welding 搭接焊:lap welding 12.船形焊: fillet welding in the downhand / flat position 13.坡口焊:groove welding 14.I 形坡口对接焊:square groove welding 15.Y形坡口对接焊:flare groove welding 16.纵缝焊接:welding of longitudinal seam. 横缝焊接:welding of transverse seam. 17.环缝焊接:girth welding, circumferential welding 18.螺旋缝焊接:welding of spiral seam, welding of helical seam. 19.环缝对接焊:Butt welding of circumferential seam. 20.单面焊:welding by one side 双面焊:welding by both sides 21.单道焊:single-pass welding, single-run welding 多道焊: multi-pass welding.. 22.单层焊:single layer welding 多层焊:multi-layer welding 23.分段多层焊:block sequence, block welding 24.连续焊:continuous welding 打底焊:backing welding 封底焊:back sealing weld 25.自动焊:automatic welding 半自动焊:semi-automatic welding
常见术语及缺陷中英文对照
品 質 部 培 訓 教 材 相關常見術語中英文對照
1、衝壓五金工藝常見術語及缺陷中英文對照: 中 文 英 文 備注 中 文 英 文 備注 弧長 Arc Length 材料 Material 基本呎寸 Basic Dimension 厚度 Thickness 錐度 Conical Taper 扭曲 Twist 擴孔 Counterbore or Spotface 弧度 Camber 錐孔 Countersink 拱形 Crossbow 深度 Deep of Depth 翹曲 Tilt 直徑 Diameter ? 彎曲 Coilset / Bow 半徑 Radius Ｒ 公差 Tolerance 個數 Number or Times - Places 2X 孔徑 Hole 不測量呎寸 Dimension Not to Scale X.XX 版次 Revision 參考呎寸 Reference Dimension (X.XX) 呎寸 Dimension 斜度 Slope 切面 Section 球直徑 Spherical Diameter S? 利角 Sharp edges 球半徑 Spherical Radius SR 半剖角 Half section 正方形 Square □ 編號呎寸 Number Sizes 平面度 Flatness □ 比例 Scale 直線度 Straightness — 單向公差 Unilateral tolerance 圓度 Roundness ○ 雙向公差 Bilateral tolerance 圓柱度 Cylindricity 規格 Specification 線輪廓度 Profile or a Line 剖面圖 Cross – Section 面輪廓度 Profile of a Surface 擠壓 Extrusion 傾斜度 Angularity ∠ 內徑 Bore 垂直度 Perpendicularity ⊥ 內應力 Internal stress 平行度 Parallelism / / 硬度 Hardness 位置度 Position 變形 Distortion 同軸度 Concentricity ◎ 刮花 Scratch 對稱度 Symmtery 碰銲 Spot Weld 圓跳動 Circular Run out 凹槽 Fluting / Groove 全跳動 Total Run out 成形 Forming A 點 A-Ponit 基準線 Datum Line 配件 fittings 焊接件 Weldment 配合 fit 回火處理 Drawing temper 裝配 fitting 夾具 Fixture 劃傷 scuffing 剪切 Shear 螺紋 screw 或 thread 剪切力 Shear force 回火 Tempering 剪切銷 Shear pin 脆性 Brittleness 剪切應力 Shear stress 脆性斷裂 Brittle fracture 間隙 Clearance 錘擊試驗 Hammer test 截面收縮 Contraction in area 單工序衝床 Simple press tool 緊配合 Driving fit 彈簧 Spring 開口 Throat 執片 Shim 抗彎強度 Bending strength 定位銷 Pilot pin 拉伸試驗 Tensile test 斷裂試驗 Fracture test 老化 Aging 斷裂應力 Breaking stress 螺母 Nut X.XX
焊接缺陷中英文对照(20200523203856)
焊接缺陷 1.裂缝：crack （焊缝/弧坑/热影响区裂纹:weld metal/crater/ heat-affected Zone (HAZ) crack） 2.焊瘤:overlap 3.冷隔：cold lap 4.未焊满: under fill / incompletely filled groove 5.咬边: undercut 6.道间没有圆滑过渡/焊缝凹陷：bum effect / Excessive concave 7.未溶合: lack of fusion / incomplete fusion 8.气孔:gas pore / blowhole (针尖状气孔:pinhole; 密集气 孔:porosity; 条虫状气孔:wormhole) 9.夹渣: slag inclusion (夹钨:tungsten inclusion; 夹杂 物:inclusion) 10.未焊透:incomplete penetration / lack of penetration 11.过度焊缝加强高：excessive reinforce / Excessive weld metal 12.电弧烧伤：Arc strike / Arc burn 13.焊接变形: welding deformation 14.烧穿:burn through 15.塌陷: excessive penetration 16.凹坑:pit / dent 17.过度打磨：excessive grinding 18.焊疤：scar
19.飞溅：spatter 20.焊缝成行不好：poor profile 21.焊角不足：lack of weld leg 附录attachment 焊接工艺方法 1.熔焊:fusion welding 压焊:pressure welding 钎焊:brazing welding 2.焊缝倾角:weld slope, inclination of weld axis. 3.焊缝转角:weld rotation, angle of rotation 4.平焊:flat position of welding, downhand welding 横焊:Horizontal position welding. 5.立焊:vertical position welding 仰焊:overhead position welding. 6.向下立焊:vertical down welding, downward welding in the vertical position. 7.向上立焊:vertical up welding, upward welding in the vertical position. 8.倾斜焊;inclined position welding 9.上坡焊: upward welding in the inclined position 10.下坡焊: downward welding in the inclined position 11.对接焊:butt welding 角焊:fillet welding 搭接焊:lap welding 12.船形焊: fillet welding in the downhand / flat position 13.坡口焊:groove welding 14.I 形坡口对接焊:square groove welding 15.Y形坡口对接焊:flare groove welding 16.纵缝焊接:welding of longitudinal seam. 横缝焊接:welding of transverse seam. 17.环缝焊接:girth welding, circumferential welding 18.螺旋缝焊接:welding of spiral seam, welding of helical seam. 19.环缝对接焊:Butt welding of circumferential seam. 20.单面焊:welding by one side 双面焊:welding by both sides 21.单道焊:single-pass welding, single-run welding 多道焊: multi-pass welding.. 22.单层焊:single layer welding 多层焊:multi-layer welding 23.分段多层焊:block sequence, block welding 24.连续焊:continuous welding 打底焊:backing welding 封底焊:back sealing weld 25.自动焊:automatic welding 半自动焊:semi-automatic welding 26.手工焊:manual welding, hand welding 27.车间焊接:shop welding 工地焊接:site welding, field welding 28.堆焊:surfacing welding, building up welding, overlaying welding.
船舶PSC检查缺陷代码【中英文对照】
Code Actions to be Taken需采取的措施 00 No Action Taken 无不需采取措施 10 Deficiency Rectified 缺陷已纠正 12 All Deficiencies Rectified 所有缺陷已纠正 15 Rectify Deficiencies At Next Port 在下一港口纠正缺陷 16 Rectify Deficiencies Within 14 Days 在14天内纠正缺陷 17 Master Instructed to Rectify Deficiencies Before Departure 要求船长在离港前纠正缺陷 18 Rectify Deficiencies Within 3 Months 在三个月内纠正缺陷 19 Entrance Prohibition for ship without Certification 未经认证的船舶禁止靠港 20 Ship Delayed to Rectify Deficiencies 船舶延期离港以纠正缺陷 25 After Delay Allowed to Sail (*Specify Date) 延期后允许开航（注明日期）30 Ship Detained 滞留船舶 35 Detention Rised (*Specify Date) 解除滞留（注明日期） 36 Ship allowed to sail after follow-up detention 船舶再次滞留后允许开航 40 Next Port Informed 通知下一港口 50 Flag State /Consul Informed 通知船旗国/领事馆 55 Flag State Consulted 咨询船旗国 60 Region State Informed 通知本区域成员国 70 Classification Society Informed 通知船级社 80 Temporary Substitution of Equipment 临时更换设备 82 Alternative equipment or method used 使用替代设备或方法 85 Investigation of Contravention of Discharge Provision (MARPOL) 违反（MARPOL）排放规定的调查 90 Letter of warning issued 签发警告信 95 Re-inspection Connection with Code 90 根据签发的警告信重新检查 96 Letter of Warning Withdrawn 收回警告信 97 Destination Unknown Information 目的港信息未知 99 Other (Specify) 其他（具体说明）
胶件缺陷中英文对照
blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕 crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤 flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕 internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑esin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件 excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷 minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手speckle斑点 mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属) flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤
铸造缺陷中英文对照
A .尺寸，形状缺陷 铸造缺陷casting defects 尺寸超差impropershrinkage allowance 尺寸不合格wrong size 模样错误excess rappingof pattern, deformed pattern, pattern error 壁厚不均differentthickness 铸型下垂mold sag 错型mold shift,shift, miss-match, cross-joint 舂移ram off, ramaway 塌型mold drop,drop off, drop out, drop sticker 上型下沉，沉芯sag( 上型和型芯下垂导致壁厚减小） 飞翅fins, joint flash 翘曲warp age,buckling, warping, camber 铸件变形warped casting 挤箱push up,cramp-off 型裂broken mold,cracked 掉砂crush ofmold, crush 变形deformation,casting distortion, warped casting B.缩孔（由凝固收缩引起) 缩孔shrinkage,shrinkaged cavity 内部缩孔internalshrinkage, dispersed shrinkage, blind shrinkage
敞露缩孔open shrinkage,external shrinkages, sink marks, depression 缩松porosity, shrinkage porosity,leakers, micro shrinkage, disperded shrinkage 缩陷sink marks,draw, suck-in 芯面缩孔core shrinkage 内角缩孔cornershrinkage, fillet shrinkage 出汗孔extruded bead,exudation 线状缩孔fissure likeshrinkage C.气体缺陷（由气体引起的孔） 气孔blowholes,gas hole, blow 针孔pinholes 裂纹状缺陷，线状缺陷fissure defects D.裂纹 裂纹crack 缩裂shrinkage crack 季裂seasoncracking, season crack 应力热裂hot cracking,hot tearing, hot tear 淬火裂纹quench crack,quenching crack 应力冷裂cold cracking,breakage, cold tearing, cold tear 龟裂crack 激冷层裂纹，白裂chill crack
缺陷中英文词汇对比
A . 尺寸，形状缺陷 铸造缺陷casting defects 尺寸超差impropershrinkage allowance 尺寸不合格wrong size 模样错误excess rappingof pattern, deformed pattern, pattern error 壁厚不均differentthickness 铸型下垂mold sag 错型mold shift,shift, miss-match, cross-joint 舂移ram off, ramaway 塌型mold drop,drop off, drop out, drop sticker 上型下沉，沉芯sag( 上型和型芯下垂导致壁厚减小） 飞翅fins, joint flash 翘曲warp age,buckling, warping, camber 铸件变形warped casting 挤箱push up,cramp-off 型裂broken mold,cracked 掉砂crush ofmold, crush 变形deformation,casting distortion, warped casting B. 缩孔（由凝固收缩引起) 缩孔shrinkage,shrinkaged cavity 内部缩孔internalshrinkage, dispersed shrinkage, blind shrinkage 敞露缩孔open shrinkage,external shrinkages, sink marks, depression 缩松porosity, shrinkage porosity,leakers, micro shrinkage, disperded shrinkage 缩陷sink marks,draw, suck-in 芯面缩孔core shrinkage 内角缩孔cornershrinkage, fillet shrinkage 出汗孔extruded bead,exudation 线状缩孔fissure likeshrinkage C. 气体缺陷（由气体引起的孔） 气孔blowholes,gas hole, blow 针孔pinholes 裂纹状缺陷，线状缺陷fissure defects D. 裂纹 裂纹crack 缩裂shrinkage crack 季裂seasoncracking, season crack 应力热裂hot cracking,hot tearing, hot tear 淬火裂纹quench crack,quenching crack 应力冷裂cold cracking,breakage, cold tearing, cold tear 龟裂crack 激冷层裂纹，白裂chill crack E. 夹杂物 夹渣slaginclusion, slag blowholes 砂眼sandinclusion, raised sand, sand hole
质量缺陷中英对照
质量缺陷中英对照1.MISSING …………….缺少…………… , 掉了…………… 例句: --- MISSING COMPONENTS 缺部件 --- MISSING PARTS 缺零件 --- MISSING MANUAL 缺操作说明 --- MISSING INSTRUCTION LEAFLET 缺说明书 --- MISSING BROCHURE 缺简介小册 --- MISSING LABEL 缺标签 --- MISSING STICKER 缺贴纸 --- MISSING BAR CODE 缺条形码 --- MISSING ASSEMBLE SHEET 缺组装说明 --- MISSING 3/16” SLOTTED BIT 缺3/16” 一字起子头 --- MISSING 10 MM DEEP SOCKET 缺10 MM 长套筒 2. N. (V + ING ) OF……. PARTS ( 或ON ……… SURFACE ) 例句: --- PITTING OF METAL PARTS 金属零件凹陷 --- FLAKING OF CHROME PLATING 镀铬层剥脱壳 --- FLASHING OF PLASTIC PARTS 塑料零件毛边 --- FAILURE ON COATING SURFACE 烤漆表面不合格 --- DEFORMATION OF RACK 框架变形 --- MOULDING OF WOODEN HANDLE 木柄发霉 --- CHIPPING ON STEEL PIPE SURFACE 铁管表面裂伤 --- CRACKING OF 13 MM SOCKET13 MM 套筒裂痕 --- DENT ON METAL PLATE SURFACE 金属板表面凹痕 --- NICK OF PLASTIC CASE 塑料盒割痕) --- DUST OF PACKAGE 包装尘污 --- RUSTING ON PLATING SURFACE 电镀表面生锈 --- SMUTTING OF ARTWORK 彩卡脏污! --- SCRATCHING ON COATING SURFACE 烤漆表面刮伤 --- SHARP EDGE OF HANDLE 手柄锐边 --- CORROSION ON METAL SURFACE 金属表面腐蚀 --- PEELING OF CHROME PLATING 镀铬层剥落
铸造缺陷中英文对照
A. 尺寸，形状缺陷 铸造缺陷 casting defects 尺寸超差 impropershrinkage allowanee 尺寸不合格wrong size 模样错误excess rappingof pattern, deformed pattern, pattern error 壁厚不均 differentthickness 铸型下垂mold sag 错型 mold shift,shift, miss-match, cross-joint 舂移 ram off, ramaway 塌型 mold drop,drop off, drop out, drop sticker 上型下沉，沉芯sag（上型和型芯下垂导致壁厚减小） 飞翅 fins, joint flash 翘曲 warp age,buckling, warping, camber 铸件变形 warped casting 挤箱 push up,cramp-off 型裂 broken mold,cracked 掉砂 crush ofmold, crush 变形 deformation,casting distortion, warped casting B. 缩孔（由凝固收缩引起） 缩孑L shrinkage,shrinkaged cavity 内部缩孑L internalshrinkage, dispersed shrinkage, blind shrinkage 敞露缩孑L open shrinkage,external shrinkages, sink marks,
depressi on 缩松 porosity, shrinkage porosity,leakers, micro shrinkage, disperded shri nkage 缩陷 sink marks,draw, suck-in 芯面缩孑L core shrinkage 内角缩孑L cornershrinkage, fillet shrinkage 出汗孑L extruded bead,exudation 线状缩孑L fissure likeshrinkage C. 气体缺陷（由气体引起的孔） 气孑L blowholes,gas hole, blow 针孑 L pin holes 裂纹状缺陷，线状缺陷fissure defects D. 裂纹 裂纹crack 缩裂 shrinkage crack 季裂 seas on crack ing, seas on crack 应力热裂 hot crack in g,hot teari ng, hot tear 淬火裂纹 quench crack,quenching crack 应力冷裂 cold crack in g,breakage, cold teari ng, cold tear 龟裂crack 激冷层裂纹，白裂chill crack E. 夹杂物
验货缺陷中英文对照
验货缺陷中英文对照DanWang 发表于: 2008-6-06 19:03 来源: 外贸验货员网 carton marking wrong/箱唛错carton was damaged/箱烂 carton wrinkle/箱邹 poor printing on carton/箱唛印刷不良 carton marking illegible/箱唛不清楚 carton too tight/箱太紧 bar code wrong/电脑纹错 wrong printing on carton/箱印刷错 bar code illegible/电脑纹模糊 missing date code/漏日期贴纸 missing bar code/漏电脑纹 missing vendor code/漏厂编号missing product inside carton./漏装产品carton joint opened/箱驳口开裂 carton unsealed/外箱无密封 glue mark on carton/外箱胶水印 gift box unseal/彩盒无密封 gift box crushed/彩盒压烂压皱 master carton/外箱 shipping carton/落货箱 inner carton/内箱 blister pack/吸塑袋 gift box pack/彩盒袋 display box pack/开口彩盒 solid pack/独立装 assortment pack/混合装 bulk pack/散包装 cable tie/扎线带 shrink warp/吸塑包装 whole pack/完整包装 bilingual pack/两种语言装 gift box dirty/soil/彩盒污糟 gift box wrinkle/彩盒皱 gift box scratched/彩盒刮伤 gift box deformed/dent/彩盒变形/凹陷gift box illegible/彩盒字迹模糊 gift box wet/彩盒湿 gift box poor sealing/彩盒封口不良gift box unsealed/彩盒无封口
常见缺陷中英文对照
FOREIGN OIL外來油污ABNORMAL SOAND聲音不正常FOREIGN PAINT外油(指噴油)ABRASION MARK擦花,擦傷FOREIGN STUFFING外來棉料BALD SPOT禿發(指稀發) FOREIGN TAPE外來貼紙BATTERY CLIP DEFORMED電子片變形FRAYING散口BENT INSERT紙卡彎曲 GAP溝,離隙BLISTER BROKEN吸塑爛 GATE MARK水口BLISTER CRUMPLED吸塑變形 GLUE MARK膠水漬BROKEN爛 HAIR Too LONG頭發太長CANNOT HOLD POSITION不能保持位置 HAIR Too SHORT頭發太短CANNOT STAND PROPERLY不能站穩或正常HARD To ASSEMBLY很難裝配COLOR MIGRATION顏色被附在吸塑蓋上HIGH UCRRENT高油流COLOR MISMATCH不對顏色HOUSING BROKEN外殼爛CRACKING裂紋 HUMAN HAIR PRESENT人的頭發在罩內CUTTINT MARK刀印INCORRECT不正確(彩盒)DAMAGED損壞INCORRECT ASSOKTMENT錯拼款DAMAGED WINDOW SHEET彩盒損壞 INSECT PRESENT昆片在罩內DEFORMED變形 INSIRT DISLOCATED底卡移位DENT MARK凹痕INSTRUCTION SHEET CAME OFF說明書離開DETACHED分離INSUFFICIENT BRIGHT GLOW明高度不足DIRT MARK污糟INSUFFICIENT PAINT COYERAGE噴油范圍不足DISLOCATED移位INTERMITTENT FUNCTION功能間斷EXCESSIVE GREASE過多潤滑位 LABEL ADHERED UPSIDE DOWN倒置貼標志EXPOSED外露 LABEL MISALIGNED LABEL 不是直線EYE DISLOCATED眼睛移位 LBEL PEEL OFF LABEL 曉起FABRIC TORN衣料破(有洞) LEAKAGE匯漏FABRIC W/PUNCH MARK/HOLE衣料走紗(有洞) LONG LOOSE THREAD長繞頭FACE COVER UP臉被復蓋(外觀) LOOSEN漏FACE DISTORTION臉變形MATERIAL TORN物料撕爛FLASH披鋒 MESSY亂POOR FITTING不足很合適MESSY HAIR亂睫發FOREIGN MATERIAL外來物料MISALIGNMENT不是直線車縫POOR HOT STAMPING熨畫不良MISSING漏POOR LABEL STICKING貼紙貼不良MISSING COO MARKING漏印箱產地來源POOR MOLDING注塑不良MISSING DATE CODE漏印日期POOR PACKING包裝不良MISSING PA/SEWING LABEL漏車縫LABEL POOR PAINTING噴油不良MISSING PART-AESTHETIC漏附件-表面POOR PLATING電鍍不良