----------------------------------- 第一步:系统配置-------------------------------------------------------------------------------------->>User name:root //输入用户名
>>User password:admin //输入密码
>>MA5680T>enable //进入普通模式
>>MA5680T #config //进入超级模式
>>MA5680T(config) #switch language-mode //切换成本地语言
>>MA5680T (config)#display board 0 //查看所有单板,如果有“待确认”单板,请用下一命令
>>MA5680T(config) #board confirm 0 //确认所有单板
>>MA5680T(config) #sysname********************* //设备命名
>>MA5680T(config)#terminal user password //修改用户密码
>>MA5680T(config)#terminal user name //创建新用户名/密码
>> (config)#autosave interval on //打开自动保存
------------------------------第二步:配置管理数据------------------------------------------------------------------------------------- >>MA5680T(config)#vlan xx standard //创建管理VLAN (一般选standard类型)
>>MA5680T(config)#port vlan xx0/19 0 //在上行口透传管理VLAN(上行端口,5680T上行端口共4个,分别为0/19 0,0/19 1,0/20 0,0/20 1)
>>MA5680T(config)#vlan xx(xx to xx)smart //创建业务VLAN (一般选SMART类型)
>>MA5680T(config)#port vlan xx(xx to xx)0/19 0 //在上行口透传业务VLAN到上行端口
>>MA5680T(config)#interface vlanif xx //创建VLAN 三层虚接口
>> (config-if-vlanif40)#ip address xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx //配置管理IP 地址
>>(config-if-vlanif40)#description xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx //对上层端口进行描述
>> (config-if-vlanif40)#quit //退出接口,返回上层
>> (config)#ip route-static0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx //配置缺省路由
-----------------------------------第三步:配置ONT---------------------------------------------------------------------------------------
步骤一:配置DBA 模板(DBA就是动态分配带宽机制)
>> (config)#dba-profile add profile-id 18profile-name "100M" type2 assure 102400 //1:8分光器流量模版
>> (config)#dba-profile add profile-id 116profile-name "77M" type2 assure 67968//1:16分光器流量模版
>> (config)#dba-profile add profile-id 132profile-name "40M" type2 assure 36672//1:32分光器流量模版
步骤二:配置线路模板(基于优先级映射方式)
>> (config)#ont-lineprofile gpon profile-id 100 profile-name "1:8_ONU" >> (config-gpon-lineprofile-100)#mapping-mode priority //设置映射类型为优先级映射
//以下用于创建通道:
>> (config-gpon-lineprofile-100)#tcont 0 dba-profile-id 100
>> (config-gpon-lineprofile-100)#gem add 0 eth tcont 0 //添加GEM port
>> (config-gpon-lineprofile-100)#gem add 1 eth tcont 0
>> (config-gpon-lineprofile-100)#gem add 2 eth tcont 0
>> (config-gpon-lineprofile-100)#gem add 3 eth tcont 0
>> (config-gpon-lineprofile-100)#gem mapping 0 0 priority 0 //设置优先级映射关系
>> (config-gpon-lineprofile-100)#gem mapping 1 0 priority 4
>> (config-gpon-lineprofile-100)#gem mapping 2 0 priority 3
>> (config-gpon-lineprofile-100)#gem mapping 3 0 priority 6
>> (config-gpon-lineprofile-100)#commit //退出之前保存线路模版配置,否则配置无效。
>> (config-gpon-lineprofile-100)#quit
>> (config)#ont-lineprofile gpon profile-id 200 profile-name "1:16_ONU"
>> (config-gpon-lineprofile-200)# mapping-mode priority
>> (config-gpon-lineprofile-200)#tcont 0 dba-profile-id 200
>> (config-gpon-lineprofile-200)#gem add 0 eth tcont 0
>> (config-gpon-lineprofile-200)#gem add 1 eth tcont 0
>> (config-gpon-lineprofile-200)#gem add 2 eth tcont 0
>> (config-gpon-lineprofile-200)#gem add 3 eth tcont 0
>> (config-gpon-lineprofile-200)#gem mapping 0 0 priority 0
>> (config-gpon-lineprofile-200)#gem mapping 1 0 priority 4
>> (config-gpon-lineprofile-200)#gem mapping 2 2 priority 3
>> (config-gpon-lineprofile-200)#gem mapping 3 0 priority 6
>> (config-gpon-lineprofile-200)#commit
>> (config-gpon-lineprofile-200)#quit
>> (config)#ont-lineprofile gpon profile-id 300 profile-name "1:32_ONU"
>> (config-gpon-lineprofile-300)#mapping-mode priority
>> (config-gpon-lineprofile-300)#tcont 0 dba-profile-id 300
>> (config-gpon-lineprofile-300)#gem add 0 eth tcont 0
>> (config-gpon-lineprofile-300)#gem add 1 eth tcont 0
>> (config-gpon-lineprofile-300)#gem add 2 eth tcont 0
>> (config-gpon-lineprofile-300)#gem add 3 eth tcont 0
>> (config-gpon-lineprofile-300)#gem mapping 0 0 priority 0
>> (config-gpon-lineprofile-300)#gem mapping 1 0 priority 4
>> (config-gpon-lineprofile-300)#gem mapping 2 2 priority 3
>> (config-gpon-lineprofile-300)#gem mapping 3 0 priority 6
>> (config-gpon-lineprofile-300)#commit
>> (config-gpon-lineprofile-300)#quit
---------------------第四步:注册ONT,并设置其管理IP ---------------------------------------------------------------------------
>>MA5680T(config)#interface gpon0/1
//进入业务单板
>>MA5680T(config-if-gpon-0/1)#port x ont-auto-find enable
//开启端口(0-3或0-7)的自动发现ONT功能
>>MA5680T(config-if-gpon-0/1)#display ont autofind x
//查看x端口下自动发现的设备
命令显示:
Command:
display ont autofind 0
------------------------------------------------------------------------
Number F/ S/ P SN Password
------------------------------------------------------------------------
1 0/ 7/ 0 32303131B402AC41
------------------------------------------------------------------------
>>MA5680T(config-if-gpon-0/1)#ont add x(端口号)x(ONT编号)sn-auth xxxxxxxxxxxxxxxx(设备序列号)snmp ont-lineprofile-id 200 desc xxxx
//ONT编号按照光分器不同而取值围不同,分别为0-7、0-15、0-31,顺序无所谓,不发生重复即可。
>>MA5680T(config-if-gpon-0/1)#ont ipconfig x(端口号)x(ONT编号)static ip-address xxx.xxx.xxx.xxx mask xxx.xxx.xxx.xxx gateway xxx.xxx.xxx.xxx vlan x priority 3
//设置B类ONU(如:MA5626G等)的管理IP为X.X.X.X,该命令下发后将会在ont上创建一个vlan并且添加了vlan interface,priority 设置根据线路模板中优先级映射的关系选择为3,也可自行调整优先级。
>>MA5680T(config-if-gpon-0/1)#quit
--------------------第五步:添加vlan的业务需端口---------------------------------------------------------------------------------
>>MA5680T(config)#service-port vlan x gpon x/x/x(机框/槽位/端口)
ont x gemport 2 multi-service user-vlan 2 rx-cttr 6 tx-cttr 6//使用了
默认流量模板6
>>MA5680T(config)#service-port vlan x gpon x/x/x(机框/槽位/端
口) ont x gemport 0 multi-service user-vlan x rx-cttr 6 tx-cttr 6 //流量模板可通过命令“display traffic table ip from-index 0”查看系统中所有流量配置模板,默认index 6为不限速。
--------------------第六步:登陆B类ONU(如MA5626G)进行配置------------------------------------------------------------------------------- >>MA5680T(config)#telnet X.X.X.X
//远程登陆到ONU
>>MA5626G(config)#vlan xxxx
//创建业务xxxx
>>MA5626G(config)#port vlan xxxx 0/0 1
//透传vlan的上行端口(PON口为0/0 1)
>>MA5626G(config)#service-port vlan xxxx eth 0/1/x multi-service user-vlan untagged rx-cttr 6 tx-cttr 6//添加vlan的业务端口,取值围为1-8、1-16、1-24,按照设备端口数围而定.eth为业务端口类型为以太口。
--------------------------------------------------------------------------------------------------------------------------------------------------------
>> (config)#save 最后一定记得保存
注意事项:
1.小区常用B类(如MA5626G)ONU设备,而A类(如HG813)
设备无法下发管理VLAN和地址,A类配置脚本详见附件文本。
2.流量模板可重新进行定义和配置,引用时只需引用index编号
即可。
3.SNMP配置脚本详见附件文本。
4.关于系统自动保存的机制,建议在进行大批量数据配置时事先
关闭,或修改自动保存的时间参数,否则会造成配置数据时系
统自动进行保存并在屏幕输出相关信息影响数据配置。
5.OLT设备用户权限与一般数通设备配置不同,详见附件华为官
方配置指导书。
6.OLT中可配置两种映射模式,即优先级映射和VLAN映射,但
鉴于VLAN映射会使得配置文件逐步增大,因此建议使用优先
级映射方式。
7.删除设备请按照注册设备步骤倒序进行,即查看service-port列
表中设备对应的service-port编号,删除该设备对应的
service-port,进入业务单板模式下执行ONT注销(删除命令)。
8.新开局OLT设备需联系华为人员装载补丁文件,否则会有相关
BUG影响业务开通和网络运行。目前地区的补丁有:SPC100、SPH117、HP1016。
常用查询命令介绍:
display ont autofind all
//全局模式下查看所有端口ONU设备自动发现
switch language-mode //全局模式下切换系统语言模式,可在中英文状态之间进行切换display current-configuration //全局模式下查看全局配置文件,添加参数可分模块显示
display service-port 参数//全局模式下查看service-port列表
display patch all //全局模式下查看系统现有所有补丁文件
save
//全局模式下保存系统配置文件
display ont autofind x //业务单板模式下查看本单板下端口ONU设备自动发现
display ont info x all //业务单板模式下查看已注册ONU设备状态
ont delete x x //业务单板模式下注销(删除)x端口下第x个ONU设备
ont modify 参数//业务单板模式下对已注册ONU设备进行相关参数编辑和调整
ont deactivate x x //业务单板模式下对已注册ONU进行去激活操作(排查流氓ONU时常用)
ont activate x x //业务单板模式下对已注册ONU进行激活操作(排查流氓ONU时常用)