机械图纸英语翻译

机加工图纸有英语看不懂？不怕！史上最全翻译都在这里了机械图纸英语翻译

ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED

未注焊缝均为连续焊

ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED

未注焊角高3mm.

ALL UNSPECIFIED RADI - R3

未注圆角R3

REMOVE ALL BURRS AND SHARP EDGES

棱角倒钝

CHANNEL 槽钢

RSA 708 角钢70X70X8

M30X1.5 pitch M30X1.5的锥螺纹

Tackweld 点焊

OD 1/4" outside dimension 1/4"的缩写外径直1/4"

75 CRS 尺寸为75 材质为冷轧钢板

410 OPENING REF 410 开口参考尺寸

40 REF 尺寸为40,参考值

2.5" BSP 2.5”圆锥管螺纹

2.5" BSPT HEXAGON 2.5”六角圆锥管螺纹(即对丝)

30x2.5 FLAT BAR 30X2.5 扁钢

TYP 2 POSNS 2处

11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH.

总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明)

FEMALE: 内扣(母扣) MALE: 外扣(公扣)

偏心轴eccentric shaft 销轴PIN

开口销COTTER PIN 螺杆screw

紧定螺钉SET SCREW 圆螺母ROUND NUT

内六角螺钉SOCKET HEAD CAP SCREW

六角螺钉HEX HD SETSCREW

六角螺栓HEX HD BOLT

挡圈closing ring

弹性挡圈circlip

轴承隔套distance sleeve of axletree

轴承axletree

深沟球轴承DEEP GROOVE BALL BEARING 无扣长non-buckle longth

弹簧SPRING

吊环螺钉LIFTING EYE BOLT

开槽盘头螺钉SLOTTED PAN HEAD SCREW 圆锥滚子轴承TAPERED ROLLER BEARING 推力球轴承THRUST BALL BEARING

平键FLAT KEY

弹簧垫圈SINGLE COIL SPRING WASHER

平垫圈FLAT WASHER

螺母FULL NYLOCK NUT

圆螺母ROUND NUT

REMOVE ALL BURRS AND SHARP EDGES 所有尖角/棱角倒角并去毛刺

40 REF 为测量的参考尺寸

OD 1/4’outside dimension 1/4"的缩写外径直1/4’------->应该为：外径值1/4"

75 CRS 尺75 材质为冷轧钢板------->应该为：尺寸75 材质为冷轧钢板

ACCESS Accessory 附件ADJ Adjustable,Adjust 调整ADPT Adapter 使适应ADV Advance 提前

AL Aluminum 铝ALLOW Allowance 允许LT Alternate 改变

ALY Alloy 合金

AMT Amout 数量

ANL Anneal 锻炼

ANSL Amer Natl Stds Institute

APPROX Approximate 大约ASME Amer Society of Mech Engrs

ASSEM Assemble 装配

ASSY Assembly 装配

AUTH Authorized 授权的

AUTO Automatic 自动的

AUX Auxiliary 辅助的

AVG Average 平均

AWG American Wire Gauge

BC Bolt Circle 螺栓圆周

BET Between 之间

BEV Bevel 斜角

BHN Brinell Hardness Number 布氏硬度值

BLK Blank ,Block 空白

B/NM Bill of Material 材料费

BOT Bottom 底部

BP or B/P Blueprint 蓝图

BRG Bearing 轴承

BRK Break 破裂

BRKT Bracket 支架

BRO Broach 钻孔

BRS Brass 黄铜

BRZ Bronze 青铜

B＆S Brown＆Shape 棕色＆形状BSC Basic 基本的

BUSH Bushing 套管

BWG Birmingham Wire Gauge CTO C Center-to-Center 中心到中心

CAD Computer Aided Design 电脑辅助设计CAM Computer-Aided Mfg

CAP Capacity 容量

CAP SCR Cap Screw 螺帽

CARB Carburize 使渗碳

CBORE Counterbore 扩孔

CCW Counter Clockwise 逆时针

CDRILL Counerdrill CDS Cold-Drawn Steel 看英文图纸的一些资料

英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）设计者（DRAWN）审查者（CHECKED）材料（MATERIAL）日期（DATE）比例（SCALE）热处理（HEAT TREATMENT）和其它一些要求，如：

1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差

2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位

3)ANGULAR TOLERANCE±1°角度公差±1°

4)DIMS TOLERANCE±0.1 未注尺寸公差±0.1

5)SURFACE FINISH 3.2 UNLESS STATED 未注粗糙度3.2

常见尺寸的标注及要求

2.1孔（HOLE）如：

（1）毛坯孔：3"DIA+1CORE 芯子3"0+1;

（2）加工孔：1"DIA1";

（3）锪孔：锪孔(注C＇BORE=COUNTER BORE锪底面孔);

（4）铰孔：1"/4 DIA REAM铰孔1"/4;

（5）螺纹孔的标注一般要表示出螺纹的直径，每英寸牙数（螺矩）螺纹种类精度等级钻深攻深，方向等如：例1.6 HOLES

EQUI-SPACED ON 5"DIA (6孔均布在5"圆周上

（EQUI-SPACED=EQUALLY SPACED均布）DRILL 1"DIA THRO＇钻1"通孔（THRO＇=THROUGH通）C/SINK22×6DEEP 沉孔22×6

例2.TAP 7"/8-14 UNF-3B THRO＇攻统一标准细牙螺纹，每英寸14牙，精度等级3B级

（注UNF=UNIFIED FINE THREAD美国标准细牙螺纹）

1"DRILL 1"/4-20 UNC-3 THD7"/8 DEEP 4HOLES NOT BREAK THRO 钻1"孔，攻1"/4美国粗牙螺纹，每英寸20牙，攻深7"/8,4孔不准钻通（UNC=UCIFIED COARSE THREAD 美国标准粗牙螺纹）

1"-14NS-2THRO 攻美国固定特种螺纹M1",每英寸牙数14,精度等级为二级（注NS=NATIONAL SPECIAL THREAD:美国固定特种标准）

2.2倒角（CHAMFER）

例1/8×45°BEV 倒角1/8×45°（注BEV=BEVEI，斜面）

1.5×45°CHAM 倒角1.5×45°(注CHAM=CHAMFER倒角)

2.3方(SQUARE)

例5"SQUARE5"×5"方

2.4剖视（SECTION）

例SECTION A-AA-A剖面

2.5圆角半径

例1"RR1"

RADIUS MUST BE SMOOTH AND BLEND INTO FACE

圆弧必须光滑且与平面相切

2.6加工余量

例DOTTED LINES INDICATED MAX FINISH 1"/8，虚线表示最大加工余量1"/8

2.7零件标记例

USE 5"/16 RAISED HAIRLINE LET-TERS MARKING ON ONE SIDE OF BODY用突起高为5"/16的细实线字母在本体一侧打标记

关于铸锻件的技术要求

例1.FORGING MUST BE ANNEALED TO BE BELOW 203 BRINELL HARDNESS 锻件必须退火处理，布氏硬度<203

例2.NORMALIZE TO 163-207BHNMUST BE FREE OF SCALE & RUST锻件正火处理，布氏硬度163-207,锻件表面不得有氧化皮和锈蚀

例3.FORGING TO BE SHOT OR SAND BLASTED锻件需经喷丸或喷砂处理

例4.UNLESS OTHERWISE SPECIFIED DRAFT ANGLES 7°未注明锻造拔模斜度7°

例5.CAST TO BE FREE OF EXCESSIVE FLASH 铸件不得有过多的毛边

例6.DRAFT ANGLE 2°UNLESS OTHER-WISE SPECIFIED 未注明铸造拔模斜度2°

总之，看英文机械工程图纸并不是高不可攀，只要坚持常看，熟记部分单词即可。

《机械工程专业英语教程》课文翻译

Lesson 1 力学的基本概念 1、词汇： statics [st?tiks] 静力学；dynamics动力学；constraint约束；magnetic [m?ɡ＇netik]有磁性的；external [eks＇t?:nl] 外面的, 外部的；meshing啮合；follower从动件；magnitude [＇m?ɡnitju:d] 大小；intensity强度，应力；non-coincident [k?u＇insid?nt]不重合；parallel [＇p?r?lel]平行；intuitive 直观的；substance物质；proportional [pr?＇p?:??n?l]比例的；resist抵抗，对抗；celestial [si＇lestj?l]天空的；product乘积；particle质点；elastic [i＇l?stik]弹性；deformed变形的；strain拉力；uniform全都相同的；velocity[vi＇l?siti]速度；scalar[＇skeil?]标量；vector[＇vekt?]矢量；displacement代替；momentum [m?u＇ment?m]动量； 2、词组 make up of由……组成；if not要不，不然；even through即使，纵然； Lesson 2 力和力的作用效果 1、词汇： machine 机器；mechanism机构；movable活动的；given 规定的，给定的，已知的；perform执行；application 施用；produce引起，导致；stress压力；applied施加的；individual单独的；muscular [＇m?skjul?]]力臂；gravity[ɡr?vti]重力；stretch伸展，拉紧，延伸；tensile[tensail]拉力；tension张力，拉力；squeeze挤；compressive 有压力的，压缩的；torsional扭转的；torque转矩；twist扭，转动；molecule [m likju:l]分子的；slide滑动; 滑行；slip滑，溜；one another 互相；shear剪切；independently独立地，自立地；beam梁；compress压；revolve (使)旋转；exert [iɡ＇z?:t]用力，尽力，运用，发挥，施加；principle原则, 原理，准则，规范；spin使…旋转；screw螺丝钉；thread螺纹； 2、词组 a number of 许多；deal with 涉及，处理；result from由什么引起；prevent from阻止，防止；tends to 朝某个方向；in combination结合；fly apart飞散； 3、译文： 任何机器或机构的研究表明每一种机构都是由许多可动的零件组成。这些零件从规定的运动转变到期望的运动。另一方面，这些机器完成工作。当由施力引起的运动时，机器就开始工作了。所以，力和机器的研究涉及在一个物体上的力和力的作用效果。 力是推力或者拉力。力的作用效果要么是改变物体的形状或者运动，要么阻止其他的力发生改变。每一种

机械图纸中英文翻译2(1)1

近几年，我厂和英国、西班牙的几个公司有业务往来，外商传真发来的图纸都是英文标注，平时阅看有一定的困难。下面把我们积累的几点看英文图纸的经验与同行们交流。 1标题栏 英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）、设计者（DRAWN）、审查者（CHECKED）、材料（MATERIAL）、日期（DATE）、比例（SCALE）、热处理（HEAT TREATMENT）和其它一些要求，如： 1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差。 2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位。 3)ANGULAR TOLERANCE±1°角度公差±1°。 4)DIMS TOLERANCE±0.1未注尺寸公差±0.1。 5)SURFACE FINISH 3.2 UNLESS STATED未注粗糙度3.2。 2常见尺寸的标注及要求 2.1孔（HOLE）如： （1）毛坯孔：3"DIAO+1CORE 芯子3"0+1; （2）加工孔：1"DIA1"; （3）锪孔：锪孔(注C＇BORE=COUNTER BORE锪底面孔); （4）铰孔：1"/4 DIA REAM铰孔1"/4; （5）螺纹孔的标注一般要表示出螺纹的直径，每英寸牙数（螺矩）、螺纹种类、精度等级、钻深、攻深，方向等。如：例1.6 HOLES EQUI-SPACED ON 5"DIA (6孔均布在5圆周上（EQUI-SPACED=EQUALLY SPACED均布） DRILL 1"DIATHRO＇ 钻1"通孔（THRO＇=THROUGH通） C/SINK22×6DEEP 沉孔22×6 例2.TAP7"/8-14UNF-3BTHRO＇ 攻统一标准细牙螺纹，每英寸14牙，精度等级3B级 （注UNF=UNIFIED FINE THREAD美国标准细牙螺纹） 1"DRILL 1"/4-20 UNC-3 THD7"/8 DEEP 4HOLES NOT BREAK THRO钻1"孔，攻1"/4美国粗牙螺纹，每英寸20牙，攻深7"/8,4孔不准钻通（UNC=UCIFIED COARSE THREAD 美国标准粗牙螺纹） 1"-14NS-2THRO 攻美国固定特种螺纹M1",每英寸牙数14,精度等级为二级 （注NS=NATIONAL SPECIAL THREAD:美国固定特种标准）

英文翻译 机械自动化类

Mechatronics Electrical machinery and electronics, also known as the integration of science, English as Mechatronics, it is by English mechanics of the first half of Mechanics and Electronics of the latter part of a combination of Electronics. Mechatronics 1971, first appeared in Japanese magazine, "Machine Design" on the supplement, with the mechanical-electrical integration of the rapid development of technology, electromechanical integration, the concept was widely accepted and we have universal application. With the rapid development of computer technology and extensive application of mechatronics technology unprecedented development. Mechatronics present technology, mechanical and micro-electronics technology is closely a set of technologies, the development of his machine has been cold humane, intelligent. Specific mechanical and electrical integration technologies, including the following: (1) mechanical engineering machinery and technology is the basis of mechatronics, mechanical technology, focused on how to adapt to mechanical and electrical integration technologies, the use of other high and new technology to update the concept, the realization of the structure, materials, the performance changes to meet the needs to reduce weight, reduce the size and improve accuracy, increase the stiffness and improving the performance requirements. Mechatronic systems in the manufacturing process, the classical theory and technology of mechanical computer-aided technology should help, while the use of artificial intelligence and expert systems, the formation of a new generation of mechanical manufacturing technology. (2) Computer and Information Technology Which information exchange, access, computing, judge and decision-making, artificial intelligence techniques, expert system technology, neural networks are computer information processing technology. (3) System Technology System technology that is the concept of the overall application of related technology organizations, from the perspective of the overall objectives and systems will be interconnected into the overall number of functional units, system interface technology is an important aspect of technology, it is an organic part of the realization of system guarantee connectivity.

机械专业术语英文翻译

陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking

技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams

机械专业外文翻译(中英文翻译)

外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important considerations in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems covering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11-and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are

(机械制造行业)机械英文翻译

英文翻译 机械设计 一台完整机器的设计是一个复杂的过程。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。 Machine Design The complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge. 任何产品在设计时第一步就是选择产品每个部分的构成材料。许多的材料被今天的设计师所使用。对产品的功能，它的外观、材料的成本、制造的成本作出必要的选择是十分重要的。对材料的特性必须事先作出仔细的评估。 One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to today's designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations. 仔细精确的计算是必要的，以确保设计的有效性。在任何失败的情况下，最好知道在最初设计中有有缺陷的部件。计算（图纸尺寸）检查是非常重要的。一个小数点的位置放错，就可以导致一个本可以完成的项目失败。设计工作的各个方面都应该检查和复查。 Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked. 计算机是一种工具，它能够帮助机械设计师减轻繁琐的计算，并对现有数据提供进一步的分析。互动系统基于计算机的能力，已经使计算机辅助设计（CAD）和计算机辅助制造（CAM）成为了可能。心理学家经常谈论如何使人们适应他们所操作的机器。设计人员的基本职责是努力使机器来适应人们。这并不是一项容易的工作，因为实际上并不存在着一个对所有人来说都是最优的操作范围和操作

钟平老师的机械翻译公式

钟平老师的机械翻译公式 2009-11-15 11:51 机械化英语翻译法 ————领航钟平老师基础版听课笔记 简介：本方法主要是运用数学的逻辑思维，将长难句进行划分层次，然后运用所总结的公式进行翻译。如果真正掌握后可以让语法近乎白痴的人在以后不会碰到翻译不了的句子，但切记：词汇是一切的根本。 一、英语之基本规则 主干先行(主、谓、宾)，废话后置(定、状) 二、主干的确定 构成一句话的主要条件是：主语+谓语 1> 谓语：a.划出所有动词；b.排除具有下列条件的动词：从句中的、句首状语、前面无助动词的分词、to do形式（谓语+to do

除外，因为它整体作谓语）、活用的动词（如动词当名词用） * 单词的活用能通过运用简单词，让写出来的句子收到意想不到的效果。 例：Chinese economy is bettering!(中国的经济越来越好） You were,are and will be in my heart.(你永远在我心中） 2> 主语： a.句首的第一个名词性结构； b.第一个谓语前的第一个名词性结构。 名词性结构：名词、代词、动名词、动词不定式、从句、It+……+从句/to do; 非名词性结构：介词短语中的名词性结构、从句中的名词性结构。 3> 宾语：每个谓语后面的名词性结构。

三、复杂英文模式之计算公式： [状语]+主语+(定语)+谓语+[小状语]+宾语+{定语或状语} 例：[Although not so world widely accepted],people (who are emotionally weak in daily business) are [often] losers {who are not able to fulfil any fruitful achievements in their lifetime that they endure}. 子公式(无宾语模式)：[状语]+主语+(定语)+谓语+[小状语] * 宾语后一般都是定语，除非一开始就有表示状语的概念（如程度、方式、目的、结果、原因等） 四、定状的汉化（核心） 1> 前提：分别划出各定状层次，包括：a.分词结构b.从句c.介词短语。 2> 状语的处理 规则1 汉化位置：句子首尾或最近的谓语前

机械专业英文翻译

启动轴starting axle 启动齿轮starting gear 启动棘轮starting ratchet wheel 复位弹簧restoring, pull back spring 弹簧座spring seating 摩擦簧friction spring 推力垫圈thrust washer 轴挡圈axle bumper ring 下料filling 切断cut 滚齿机gear-hobbing machine 剪料机material-shearing machine 车床lathe 拉床broaching machine 垂直度verticality, vertical extent 平行度 parallelism同心度 homocentricity 位置度position 拉伤pulling damage 碰伤bumping damage 缺陷deficiency 严重缺陷severe deficiency 摩擦力friction 扭距twist 滑动glide 滚动roll 打滑skid 脱不开can’t seperate 不复位can’t restore 直径diameter M值= 跨棒距test rod span 公法线common normal line 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 机床machine tool 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 剪切shear 扭转twist 弯曲应力bending stress 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 电路circuit 半导体元件semiconductor element 拉孔broaching 装配assembling 加工machining 液压hydraulic pressure 切线tangent 机电一体化mechanotronics mechanical-electrical integration 稳定性stability 介质medium 液压驱动泵fluid clutch 液压泵hydraulic pump 阀门valve 失效invalidation 强度intensity 载荷load 应力stress 安全系数safty factor 可靠性reliability 螺纹thread 螺旋helix 键spline 销pin 滚动轴承rolling bearing 滑动轴承sliding bearing 弹簧spring 制动器arrester brake 十字结联轴节crosshead 联轴器coupling 链chain 皮带strap 精加工finish machining 粗加工rough machining 变速箱体gearbox casing 腐蚀rust 氧化oxidation 磨损wear 耐用度durability 机械制图 Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求 technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer

机械图纸英语翻译

1，PERMANENTLY MARK PART NUMBER(ALL METHODS ACCEPTABLE)IN LOCATION SHOWN：SAME AS DWG NO.INCLUDING REV & DATE OF MFG 2，REMOVE ALL BURRS AND BREAK ALL EDGES 3，ALL DIMENSIONS AND TOLERANCES APPLY AFTER FINISHING(IF REQUIRED) 4，COSMETIC INSPECTION CLASS IIA-EXTERNAL COMPONENT 5，MATERIAL：LAMINATED 1/2" CORIAN；COLOR SPECIFIED IN PURCHASE ORDER 6，FINISH：LAMINATION TO APPEAR SEAMLESS;NO PITTS OR LINES POST MACHINING：CLEAN & FURTHER SPECIFICATION IN PO 7，POLISHING：IF SPECIFIED IN PO；TOP，SIDES，CHAMFER & 1/2" FROM EDGE ON BASE SURFACE 8，ARTWORK：IF SPECIFIED IN PO；TO BE READ FROM ELLIPTICAL PROFILE 9，PART TO BE MANUFACTURED REFERENCING DWG AND 3D GEOMETRY SUPPLIED 2，1.如图所示的位置上加上耐久的产品编号标记,就是图纸编号包括图纸版本号及生产日期. 2.除去所有毛刺及所有边倒角. 3.(如必要的话)产品表面处理后,所有的尺寸及公差要符合要求. 4.外观检测等级为【信息工业协会[美]-外观件】 5.产品材料:1/2 英寸厚的"可丽耐"薄板, 颜色在采购单内注明. 6.表面要求:层压后无结合线,无凹坑或凸凹线状, 后处理: 洁净及详细请看采购单说明. 7.表面抛光: 如果在采购单中有说明则按其要求做,否则顶部,侧面,倒角斜面及底边上来1/2英寸处要抛光. 8.美工; 如果在采购单中有说明则按其要求做,否则从椭圆形中来读取(这一点要能与你们专业有关,我就不是很清楚, 要看产品图才知) 9.产品加工请参照提供的工程图及三维立体图. Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板

机械类英语论文及翻译翻译

High-speed milling High-speed machining is an advanced manufacturing technology, different from the traditional processing methods. The spindle speed, cutting feed rate, cutting a small amount of units within the time of removal of material has increased three to six times. With high efficiency, high precision and high quality surface as the basic characteristics of the automobile industry, aerospace, mold manufacturing and instrumentation industry, such as access to a wide range of applications, has made significant economic benefits, is the contemporary importance of advanced manufacturing technology. For a long time, people die on the processing has been using a grinding or milling EDM (EDM) processing, grinding, polishing methods. Although the high hardness of the EDM machine parts, but the lower the productivity of its application is limited. With the development of high-speed processing technology, used to replace high-speed cutting, grinding and polishing process to die processing has become possible. To shorten the processing cycle, processing and reliable quality assurance, lower processing costs. 1 One of the advantages of high-speed machining High-speed machining as a die-efficient manufacturing, high-quality, low power consumption in an advanced manufacturing technology. In conventional machining in a series of problems has plagued by high-speed machining of the application have been resolved. 1.1 Increase productivity High-speed cutting of the spindle speed, feed rate compared withtraditional machining, in the nature of the leap, the metal removal rate increased 30 percent to 40 percent, cutting force reduced by 30 percent, the cutting tool life increased by 70% . Hardened parts can be processed, a fixture in many parts to be completed rough, semi-finishing and fine, and all other processes, the complex can reach parts of the surface quality requirements, thus increasing the processing productivity and competitiveness of products in the market. 1.2 Improve processing accuracy and surface quality High-speed machines generally have high rigidity and precision, and other characteristics, processing, cutting the depth of small, fast and feed, cutting force low, the workpiece to reduce heat distortion, and high precision machining, surface roughness small. Milling will be no high-speed processing and milling marks the surface so that the parts greatly enhance the quality of the surface. Processing Aluminum when up Ra0.40.6um, pieces of steel processing at up to Ra0.2 ~ 0.4um.

机械专业相关词汇中英文翻译大全

机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus

机械工程专业英语 翻译

2、应力和应变 在任何工程结构中独立的部件或构件将承受来自于部件的使用状况或工作的外部环境的外力作用。如果组件就处于平衡状态,由此而来的各种外力将会为零,但尽管如此,它们共同作用部件的载荷易于使部件变形同时在材料里面产生相应的内力。 有很多不同负载可以应用于构件的方式。负荷根据相应时间的不同可分为: (a)静态负荷是一种在相对较短的时间内逐步达到平衡的应用载荷。 (b)持续负载是一种在很长一段时间为一个常数的载荷, 例如结构的重量。这种类型的载荷以相同的方式作为一个静态负荷; 然而,对一些材料与温度和压力的条件下,短时间的载荷和长时间的载荷抵抗失效的能力可能是不同的。 (c)冲击载荷是一种快速载荷(一种能量载荷)。振动通常导致一个冲击载荷, 一般平衡是不能建立的直到通过自然的阻尼力的作用使振动停止的时候。 (d)重复载荷是一种被应用和去除千万次的载荷。 (e)疲劳载荷或交变载荷是一种大小和设计随时间不断变化的载荷。 上面已经提到，作用于物体的外力与在材料里面产生的相应内力平衡。因此,如果一个杆受到一个均匀的拉伸和压缩，也就是说, 一个力,均匀分布于一截面,那么产生的内力也均匀分布并且可以说杆是受到一个均匀的正常应力,应力被定义为 应力==负载 P /压力 A, 因此根据载荷的性质应力是可以压缩或拉伸的,并被度量为牛顿每平方米或它的倍数。 如果一个杆受到轴向载荷，即是应力，那么杆的长度会改变。如果杆的初始长度L和改变量△L已知，产生的应力定义如下: 应力==改变长△L /初始长 L 因此应力是一个测量材料变形和无量纲的物理量 ,即它没有单位;它只是两个相同单位的物理量的比值。 一般来说,在实践中,在荷载作用下材料的延伸是非常小的, 测量的应力以*10-6的形式是方便的, 即微应变, 使用的符号也相应成为ue。 从某种意义上说，拉伸应力与应变被认为是正的。压缩应力与应变被认为是负的。因此负应力使长度减小。 当负载移除时，如果材料回复到初始的，无负载时的尺寸时，我们就说它是具有弹性的。一特定形式的适用于大范围的工程材料至少工程材料受载荷的大部分的弹性, 产生正比于负载的变形。由于载荷正比于载荷所产生的压力并且变形正比于应变, 这也说明,当材料是弹性的时候, 应力与应变成正比。因此胡克定律陈述, 应力正比于应变。 这定律服从于大部分铁合金在特定的范围内, 甚至以其合理的准确性可以假定适用于其他工程材料比如混凝土，木材，非铁合金。 当一个材料是弹性的时候，当载荷消除之后，任何负载所产生的变形可以完全恢复,没有永久的变形。

机械术语英文翻译

机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch