验货缺陷中英文对译明

缺陷中英文对译明细

注塑件缺陷中英文对照表

注塑件缺陷中英文对照表 中文英文 -------- -------------------- 起泡 Blister 起霜 Blooming 破孔 Blow hole 泛白 Blushing 侧壁皱纹 Body wrinkle 冒口带肉 Breaking-in 膜泡、气泡 Bubble 糊斑 Burn mark 毛边(金属) Burr （for metal）翘曲 Camber 气泡 Cell 表面中部波皱 Center buckle 细裂痕 Check 龟裂 Checking 修整表面缺陷 Chipping 铸件凹痕 Clamp-off 塌陷 Collapse 色斑 Color mottle 腐蚀 Corrosion 外观不良 Cosmetic defect 裂痕 Crack 碎裂、龟裂 Crazing 变形 Deformation 切边碎片 Edge 裂边 Edge crack 退色 Fading 填充料斑 Filler speak 裂纹 Fissure 凸缘起皱 Flange wrinkle 毛边 Flash 刮伤 Flaw 流痕 Flow mark, flow line 字体模糊 Foggy 毛边 Galling 光滑 Glazing 光泽 Gloss 污斑 Grease pits 油污、脏污 Grease, oil stains 磨痕 Grinding defect 发裂 Haircrack 雾度 Haze

水锈 Incrustation 杂质 Inclusion 压痕 Indentation 内部气孔 Internal porosity 发霉 Mildewed, moldy, mouldy 偏模 Mismatch 杂色 Mixed color 斑点 Mottle 缩颈 Necking 割痕 Nick 橘皮状表面缺陷 Orange peel 溢流 Overflow 剥离 Peeling, peel-off 坑 Pit 点状腐蚀 Pitting corrosion 模板印痕 Plate mark 麻点 Pock 痘斑 Pock mark 树脂流纹 Resin streak 树脂脱落 Resin wear 凹陷 Riding 松垂 Sagging 皂化 Saponification 疤痕 Scar 废料 Scrap 废料阻塞 Scrap jam 刮伤、划痕、划伤 Scratch 深冲表面划伤 Scuffing 裂痕 Seam 模口挤痕 Shock line 充填不足 Short shot 凹孔 Shrinkage pool 缩水 Shrinking, shrinkage 凹痕、凹陷 Sink mark, shrink Line , sink mark 表皮折迭 Skin inclusion 螺丝滑头、滑手 Slipped screw head, slippery screw thread 斑点 Speckle 矫直 Straightening 条状痕、条纹 Streak 表面裂痕 Surface check 橘皮状表皮皱折 Surface roughening 波动 Surging 冒汗 Sweat out 扭曲 Torsion

焊接缺陷中英文对照

精心整理 焊接缺陷 1. 裂缝：crack （焊缝/弧坑/热影响区裂纹:weldmetal/crater/heat-affectedZone(HAZ)crack ） 2. 焊瘤:overlap 3. 冷隔：coldlap 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 塌陷:excessivepenetration 16. 凹坑:pit/dent 17. 过度打磨：excessivegrinding 18. 焊疤：scar 19. 飞溅：spatter

20.焊缝成行不好：poorprofile 21.焊角不足：lackofweldleg 附录attachment 焊接工艺方法 1.熔焊:fusionwelding压焊:pressurewelding钎焊:brazingwelding 2.焊缝倾角:weldslope,inclinationofweldaxis. 3.焊缝转角:weldrotation,angleofrotation 4.平焊 5.立焊 6. 7. 8. 9. 10. 11. 12. 13. 14.I 15.Y 16. 17. 18. 19. 20. 21. 22. 23. 24. 25. 26. 27. 28.堆焊 29.衬垫焊:weldingwithbacking. 30.焊剂垫焊:weldingwithfluxbacking 31.电弧点焊:arcspotwelding. 32.套环:ferrule试板testpiece随机检查randomcheck 33.单面/双面串联点焊:direct/indirectserialspotswelding. 34.机械性能试验mechanicalpropertiestest 35.简历curriculumvitae 36.分类category 37.风险评估riskassessment 38.第三方notifiedbody 39.基准modules

主要缺陷中英文对照

主要缺陷中英文对照

————————————————————————————————作者：————————————————————————————————日期： 2

德仕科技（深圳）有限公司 品管部中英文对照表（一） 主要缺陷中英文对照 序号中文英文 序 号 中文英文 1 披峰Flash 16 流痕Flow mark 2 走不齐/ 缺胶 Short shot 17 色差 abberration 3 变形/注塑 后变形 Deformation 18 夹水线Weld lines 4 偏模Mismatch 19 碰伤Bump damage 5 起泡Blister 20 银线Silver 6 污斑Grease pits 21 少数量Packing shortage 7 雾化Atomization 22 泛白Blushing 8 烧焦Burn mark 23 发白Whitening 9 油污Oil mark 24 刮伤Scratch 10 气泡Blister 25 气纹Gas lines 11 划痕Scffing 26 混色Color mixture 12 泛黄Yellowing 27 斑点/污 点/ 黑点 Macula 13 缩水Sink mark 28 结合线 14 段差29 拉伤Pull 15 抛光不良Polishing mark 30 水印Watermark 主要测量仪器中英文对照

序号中文英文 序 号 中文英文 1 分厘卡(千 分尺) Micrometer 14 卡尺Caliper 2 C表Dial gauge 15 扁分厘卡Blade micrometer 3 块规Block gauge 16 针规Pin gauge 4 CMM X-Y-Z Coordinate 17 电子卡尺Digital caliper 5 扭力计Torque meter 18 投影仪Projection apparatus 6 高度仪Height gauge 19 直角尺Square master 7 游标卡尺Vernier caliper 20 硬度机Durometer 8 牙规Scre gauge 21 半径规Radius gauge 9 角度规Universal protractor 22 特别塞规Ring gauge 10 拉/推力计Pull/Push gauge 23 弹力计Spring balance 11 塞尺Clearance gauge 24 专用夹具Special fixture 12 工具显微 镜 Tool-measuring microscope 25 千分表Dial indicator 13 1 抽样Sampling 11 抽样计划 Sampling plan 2 样品数量Sample size 12 合格Conformity

焊接缺陷中英文对照

焊接缺陷1.裂缝：crack （焊缝/弧坑/热影响区裂纹:weld metal/crater/ heat-affected Zone (HAZ) crack） 2.焊瘤:overlap 3.冷隔：cold lap 4.未焊满: under fill / incompletely filled groove 5.咬边: undercut 6.道间没有圆滑过渡/焊缝凹陷：bum effect / Excessive concave 7.未溶合: lack of fusion / incomplete fusion 8.气孔:gas pore / blowhole (针尖状气孔:pinhole; 密集气 孔:porosity; 条虫状气孔:wormhole) 9.夹渣: slag inclusion (夹钨:tungsten inclusion; 夹杂 物:inclusion) 10.未焊透:incomplete penetration / lack of penetration 11.过度焊缝加强高：excessive reinforce / Excessive weld metal 12.电弧烧伤：Arc strike / Arc burn 13.焊接变形: welding deformation 14.烧穿:burn through 15.塌陷: excessive penetration 16.凹坑:pit / dent 17.过度打磨：excessive grinding

scar 焊疤：18. 19.飞溅：spatter 20.焊缝成行不好：poor profile 21.焊角不足：lack of weld leg 附录 attachment 焊接工艺方法 1.熔焊:fusion welding 压焊:pressure welding 钎焊:brazing welding 2.焊缝倾角:weld slope, inclination of weld axis. 3.焊缝转角:weld rotation, angle of rotation 4.平焊:flat position of welding, downhand welding 横焊:Horizontal position welding. 5.立焊:vertical position welding 仰焊:overhead position welding. 6.向下立焊:vertical down welding, downward welding in the vertical position. 7.向上立焊:vertical up welding, upward welding in the vertical position. 8.倾斜焊;inclined position welding 9.上坡焊: upward welding in the inclined position 10.下坡焊: downward welding in the inclined position 11.对接焊:butt welding 角焊:fillet welding 搭接焊:lap welding 12.船形焊: fillet welding in the downhand / flat position 13.坡口焊:groove welding 14.I 形坡口对接焊:square groove welding 15.Y形坡口对接焊:flare groove welding 16.纵缝焊接:welding of longitudinal seam. 横缝焊接:welding of transverse seam. 17.环缝焊接:girth welding, circumferential welding 18.螺旋缝焊接:welding of spiral seam, welding of helical seam. 19.环缝对接焊:Butt welding of circumferential seam. 20.单面焊:welding by one side 双面焊:welding by both sides 21.单道焊:single-pass welding, single-run welding 多道焊: multi-pass welding.. 22.单层焊:single layer welding 多层焊:multi-layer welding 23.分段多层焊:block sequence, block welding 24.连续焊:continuous welding 打底焊:backing welding 封底焊:back sealing weld 25.自动焊:automatic welding 半自动焊:semi-automatic welding

常见术语及缺陷中英文对照

品 質 部 培 訓 教 材 相關常見術語中英文對照

1、衝壓五金工藝常見術語及缺陷中英文對照: 中 文 英 文 備注 中 文 英 文 備注 弧長 Arc Length 材料 Material 基本呎寸 Basic Dimension 厚度 Thickness 錐度 Conical Taper 扭曲 Twist 擴孔 Counterbore or Spotface 弧度 Camber 錐孔 Countersink 拱形 Crossbow 深度 Deep of Depth 翹曲 Tilt 直徑 Diameter ? 彎曲 Coilset / Bow 半徑 Radius Ｒ 公差 Tolerance 個數 Number or Times - Places 2X 孔徑 Hole 不測量呎寸 Dimension Not to Scale X.XX 版次 Revision 參考呎寸 Reference Dimension (X.XX) 呎寸 Dimension 斜度 Slope 切面 Section 球直徑 Spherical Diameter S? 利角 Sharp edges 球半徑 Spherical Radius SR 半剖角 Half section 正方形 Square □ 編號呎寸 Number Sizes 平面度 Flatness □ 比例 Scale 直線度 Straightness — 單向公差 Unilateral tolerance 圓度 Roundness ○ 雙向公差 Bilateral tolerance 圓柱度 Cylindricity 規格 Specification 線輪廓度 Profile or a Line 剖面圖 Cross – Section 面輪廓度 Profile of a Surface 擠壓 Extrusion 傾斜度 Angularity ∠ 內徑 Bore 垂直度 Perpendicularity ⊥ 內應力 Internal stress 平行度 Parallelism / / 硬度 Hardness 位置度 Position 變形 Distortion 同軸度 Concentricity ◎ 刮花 Scratch 對稱度 Symmtery 碰銲 Spot Weld 圓跳動 Circular Run out 凹槽 Fluting / Groove 全跳動 Total Run out 成形 Forming A 點 A-Ponit 基準線 Datum Line 配件 fittings 焊接件 Weldment 配合 fit 回火處理 Drawing temper 裝配 fitting 夾具 Fixture 劃傷 scuffing 剪切 Shear 螺紋 screw 或 thread 剪切力 Shear force 回火 Tempering 剪切銷 Shear pin 脆性 Brittleness 剪切應力 Shear stress 脆性斷裂 Brittle fracture 間隙 Clearance 錘擊試驗 Hammer test 截面收縮 Contraction in area 單工序衝床 Simple press tool 緊配合 Driving fit 彈簧 Spring 開口 Throat 執片 Shim 抗彎強度 Bending strength 定位銷 Pilot pin 拉伸試驗 Tensile test 斷裂試驗 Fracture test 老化 Aging 斷裂應力 Breaking stress 螺母 Nut X.XX

焊接缺陷中英文对照(20200523203856)

焊接缺陷 1.裂缝：crack （焊缝/弧坑/热影响区裂纹:weld metal/crater/ heat-affected Zone (HAZ) crack） 2.焊瘤:overlap 3.冷隔：cold lap 4.未焊满: under fill / incompletely filled groove 5.咬边: undercut 6.道间没有圆滑过渡/焊缝凹陷：bum effect / Excessive concave 7.未溶合: lack of fusion / incomplete fusion 8.气孔:gas pore / blowhole (针尖状气孔:pinhole; 密集气 孔:porosity; 条虫状气孔:wormhole) 9.夹渣: slag inclusion (夹钨:tungsten inclusion; 夹杂 物:inclusion) 10.未焊透:incomplete penetration / lack of penetration 11.过度焊缝加强高：excessive reinforce / Excessive weld metal 12.电弧烧伤：Arc strike / Arc burn 13.焊接变形: welding deformation 14.烧穿:burn through 15.塌陷: excessive penetration 16.凹坑:pit / dent 17.过度打磨：excessive grinding 18.焊疤：scar

19.飞溅：spatter 20.焊缝成行不好：poor profile 21.焊角不足：lack of weld leg 附录attachment 焊接工艺方法 1.熔焊:fusion welding 压焊:pressure welding 钎焊:brazing welding 2.焊缝倾角:weld slope, inclination of weld axis. 3.焊缝转角:weld rotation, angle of rotation 4.平焊:flat position of welding, downhand welding 横焊:Horizontal position welding. 5.立焊:vertical position welding 仰焊:overhead position welding. 6.向下立焊:vertical down welding, downward welding in the vertical position. 7.向上立焊:vertical up welding, upward welding in the vertical position. 8.倾斜焊;inclined position welding 9.上坡焊: upward welding in the inclined position 10.下坡焊: downward welding in the inclined position 11.对接焊:butt welding 角焊:fillet welding 搭接焊:lap welding 12.船形焊: fillet welding in the downhand / flat position 13.坡口焊:groove welding 14.I 形坡口对接焊:square groove welding 15.Y形坡口对接焊:flare groove welding 16.纵缝焊接:welding of longitudinal seam. 横缝焊接:welding of transverse seam. 17.环缝焊接:girth welding, circumferential welding 18.螺旋缝焊接:welding of spiral seam, welding of helical seam. 19.环缝对接焊:Butt welding of circumferential seam. 20.单面焊:welding by one side 双面焊:welding by both sides 21.单道焊:single-pass welding, single-run welding 多道焊: multi-pass welding.. 22.单层焊:single layer welding 多层焊:multi-layer welding 23.分段多层焊:block sequence, block welding 24.连续焊:continuous welding 打底焊:backing welding 封底焊:back sealing weld 25.自动焊:automatic welding 半自动焊:semi-automatic welding 26.手工焊:manual welding, hand welding 27.车间焊接:shop welding 工地焊接:site welding, field welding 28.堆焊:surfacing welding, building up welding, overlaying welding.

纺织验货用语中英文对照

验货用语资料成品检验Checking of finished products 检验，检查inspection, check 商检commodity inspection 领面松wrinkles at top collar 领面紧top collar appears tight 领面起泡crumples at top collar 领外口松collar edge appears loose 领外口紧collar edge appears tight 底领伸出collar band is longer than collar 底领缩进collar band is shorter than collar 底领里起皱wrinkles at collar band facing 底领外露collar band lean out of collar 倘领偏斜collar deviates from front center line 领窝不平creases below neckline 后领窝起涌bunches below back neckline 驳头起皱wrinkles at top lapel 驳头反翘top lapel appears tight 驳头外口松lapel edge appears loose

驳头外口紧lapel edge appears tight 驳口不直lapel roll line is uneven 串口不直gorge line is uneven 领卡脖tight neckline 领离脖collar stand away from neck 小肩起皱puckers at shoulders 塌肩wrinkles at shoulder 袖隆起皱creases at underarm 袖隆缝起皱puckers at underarm seam 塌胸lack of fullness at chest 省尖起泡crumples at dart point 拉链起皱wrinkles at zip fly 止口不直front edge is uneven 止口缩角front edge is out of square 止口反翘front edge is upturned 止口反吐facing leans out of front edge 止口豁split at front edge 止口下部搭叠过多crossing at front edge 底边起皱wrinkles at hem 后身起吊back of coat rides up 背衩豁开split at back vent 背衩搭叠过多crossing at back vent

船舶PSC检查缺陷代码【中英文对照】

Code Actions to be Taken需采取的措施 00 No Action Taken 无不需采取措施 10 Deficiency Rectified 缺陷已纠正 12 All Deficiencies Rectified 所有缺陷已纠正 15 Rectify Deficiencies At Next Port 在下一港口纠正缺陷 16 Rectify Deficiencies Within 14 Days 在14天内纠正缺陷 17 Master Instructed to Rectify Deficiencies Before Departure 要求船长在离港前纠正缺陷 18 Rectify Deficiencies Within 3 Months 在三个月内纠正缺陷 19 Entrance Prohibition for ship without Certification 未经认证的船舶禁止靠港 20 Ship Delayed to Rectify Deficiencies 船舶延期离港以纠正缺陷 25 After Delay Allowed to Sail (*Specify Date) 延期后允许开航（注明日期）30 Ship Detained 滞留船舶 35 Detention Rised (*Specify Date) 解除滞留（注明日期） 36 Ship allowed to sail after follow-up detention 船舶再次滞留后允许开航 40 Next Port Informed 通知下一港口 50 Flag State /Consul Informed 通知船旗国/领事馆 55 Flag State Consulted 咨询船旗国 60 Region State Informed 通知本区域成员国 70 Classification Society Informed 通知船级社 80 Temporary Substitution of Equipment 临时更换设备 82 Alternative equipment or method used 使用替代设备或方法 85 Investigation of Contravention of Discharge Provision (MARPOL) 违反（MARPOL）排放规定的调查 90 Letter of warning issued 签发警告信 95 Re-inspection Connection with Code 90 根据签发的警告信重新检查 96 Letter of Warning Withdrawn 收回警告信 97 Destination Unknown Information 目的港信息未知 99 Other (Specify) 其他（具体说明）

胶件缺陷中英文对照

blister 起泡blooming 起霜blow hole 破孔blushing 泛白body wrinkle 侧壁皱纹breaking-in 冒口带肉bubble 膜泡burn mark 糊斑burr 毛边camber 翘曲cell 气泡 center buckle 表面中部波皱check 细裂痕checking 龟裂chipping 修整表面缺陷 clamp-off 铸件凹痕collapse 塌陷color mottle 色斑corrosion 腐蚀crack 裂痕 crazing 碎裂crazing 龟裂deformation 变形edge 切边碎片edge crack 裂边 fading 退色filler speak 填充料斑fissure 裂纹flange wrinkle 凸缘起皱flaw 刮伤 flow mark 流痕galling 毛边glazing 光滑gloss 光泽grease pits 污斑 grinding defect 磨痕haircrack 发裂haze 雾度incrustation 水锈indentation 压痕 internal porosity 内部气孔mismatch 偏模mottle 斑点necking 缩颈nick 割痕 orange peel 橘皮状表面缺陷overflow 溢流peeling 剥离pit 坑pitting corrosion 点状腐蚀plate mark 模板印痕pock 麻点pock mark 痘斑esin streak 树脂流纹resin wear 树脂脱落riding 凹陷sagging 松垂saponification 皂化scar 疤痕scrap 废料scrap jam 废料阻塞scratch 刮伤/划痕scuffing 深冲表面划伤seam 裂痕shock line 模口挤痕 short shot 充填不足shrinkage pool 凹孔sink mark 凹痕skin inclusion 表皮折迭straightening 矫直streak 条状痕surface check 表面裂痕surface roughening 橘皮状表皮皱折surging 波动sweat out 冒汗torsion 扭曲warpage 翘曲waviness 波痕webbing 熔塌 weld mark 焊痕whitening 白化wrinkle 皱纹missing part漏件wrong part错件 excessive defects过多的缺陷critical defect极严重缺陷major defect主要缺陷 minor defect次要缺陷not up to standard不合规格dimension/size is a little bigger尺寸偏大(小) cosmetic defect外观不良slipped screwhead/slippery screw head螺丝滑头 slipped screwhead/shippery screw thread滑手speckle斑点 mildewed=moldy=mouldy发霉rust生锈deformation变形burr(金属) flash(塑件)毛边poor staking铆合不良excesssive gap间隙过大 grease/oil stains油污 inclusion杂质 painting peel off脏污 shrinking/shrinkage缩水 mixed color杂色 scratch划伤

验货中英文对照表

五金工艺品生产流程及验货要点 The Producing Procedure & Quality Checking Points Hard-lines 生产流程Producing Procedure （冲压类/metal sheet） l 备料raw material incoming→ l 剪料material cutting→ l 模具成型molding & shaping→ l 效果处理finish（抛光polishing/喷沙sand basting/印刷printing/电镀electric-plating/喷漆spraying/喷粉coating等）→ l 返修re-inspecting repairing→ l 装配assembly→ l 包装packing→ l 出货shipment （铁线类/wire） l 备料raw material incoming→ l 剪料material cutting→ l 弯型bending/焊接welding/打磨(?grilding)/成型shaping→ l 效果处理finishing(喷漆spraying/喷粉coating/手绘hand-painting/电镀等electric-plating etc）→ l 返修re-inspection & repairing→ l 装配assembly→

l 包装packing→ l 出货shipment 验货要点Quality Checking Points l 尺寸/size l 颜色形状/color & shape l 效果处理/finish & effect l 重量/weight l 平稳度/stability l 沙眼/tiny hole l 刮手/sharp point l 功能等/function 转自: [url=https://www.sodocs.net/doc/9015531921.html,/?fromuid=86459]验货员论坛[/url] https://www.sodocs.net/doc/9015531921.html,/viewthread.php?tid=66238&fromuid=86459

验货必备纺织术语疵点描述中英文对照

验货必备--纺织术语,疵点描述--中英文对照 验货必备--纺织术语,疵点描述--中英文对照 本人在SGS的CTS部门工作5年, 涉及到的产品种类有:陶瓷,玻璃,餐具,家具,家紡,五金(户内,户外),等一些大的种类,小的分类就不在此细说了,如(PE;PVC手套,钉子,等).涉及客户有:CGSA,WGAL,KAL,OBI,THD,TESCO,LENOX,AUCHAN, SIPLEC,等一些客户,其他的小客户就不在此赘述了. 抽检标准执行ANSI/ASQZ1.4-2003.AQL可依据客户要求而定.主要以F.R.I.为主,如果是I.P.C.或者L/S也可以. 验货标准可依据欧标或者美标来执行,也可依据客户要求来执行. 本人承接河北省地区的验货.非诚勿扰.联系方式:EMAIL: my2099@https://www.sodocs.net/doc/9015531921.html, 以下附上(纺织术语,疵点描述--中英文对照),本人不敢说非常精化,纯粹个人多年经验积累.如有不当之处,还请大家添补指正. "hand feel"not as sample(tough&feel)手感与样品不符 1/2hip measure xx cm from waist("V"meas./straight

meas.)1/2坐围 1/2waist relaxed or stretched1/2腰围 2years limited warranty for sleeping bag睡袋有2年保质期 2/4-hole button2/4孔扣 3/4/5/6/7panels cap三/四/五/六/七瓣帽 4dry crock and3wet crock:color fastness standard色牢度标准：４干／３湿摩擦 5thread overlock(5TH OL)五线包缝 60count yarn60支纱 a candlewick bedspread灯芯纱盘花床罩 a crisscross pattern十字形花样 a dress suit男式夜礼服 a gym suit体操衣 a lounge suit男式普通西服 a monogrammed shirt有字母组合图案的衬衫 a three-piece suit三件一套的西服 a veiled design woven in fabric暗花 a veiled or covered button(on clothing)暗扣 A/B/C-cup brassiere(bra)小/中/大号奶罩 abdomen girth腹围 abdominal belt腹带,肚带,兜肚(妇女,儿童用) above crotch(裤)衩上

(英)纺织验货用语中英文对照

验货用语资料 成品检验Checking of finished products 检验，检查inspection, check 商检commodity inspection 领面松wrinkles at top collar 领面紧top collar appears tight 领面起泡crumples at top collar 领外口松collar edge appears loose 领外口紧collar edge appears tight 底领伸出collar band is longer than collar 底领缩进collar band is shorter than collar 底领里起皱wrinkles at collar band facing 底领外露collar band lean out of collar 倘领偏斜collar deviates from front center line 领窝不平creases below neckline 后领窝起涌bunches below back neckline 驳头起皱wrinkles at top lapel 驳头反翘top lapel appears tight 驳头外口松lapel edge appears loose 驳头外口紧lapel edge appears tight 驳口不直lapel roll line is uneven 串口不直gorge line is uneven

领卡脖tight neckline 领离脖collar stand away from neck 小肩起皱puckers at shoulders 塌肩wrinkles at shoulder 袖隆起皱creases at underarm 袖隆缝起皱puckers at underarm seam 塌胸lack of fullness at chest 省尖起泡crumples at dart point 拉链起皱wrinkles at zip fly 止口不直front edge is uneven 止口缩角front edge is out of square 止口反翘front edge is upturned 止口反吐facing leans out of front edge 止口豁split at front edge 止口下部搭叠过多crossing at front edge 底边起皱wrinkles at hem 后身起吊back of coat rides up 背衩豁开split at back vent 背衩搭叠过多crossing at back vent 绗棉起皱puckers at quilting 絮棉不均padded cotton is uneven 边缘缺棉empty hem

缺陷中英文词汇对比

A . 尺寸，形状缺陷 铸造缺陷casting defects 尺寸超差impropershrinkage allowance 尺寸不合格wrong size 模样错误excess rappingof pattern, deformed pattern, pattern error 壁厚不均differentthickness 铸型下垂mold sag 错型mold shift,shift, miss-match, cross-joint 舂移ram off, ramaway 塌型mold drop,drop off, drop out, drop sticker 上型下沉，沉芯sag( 上型和型芯下垂导致壁厚减小） 飞翅fins, joint flash 翘曲warp age,buckling, warping, camber 铸件变形warped casting 挤箱push up,cramp-off 型裂broken mold,cracked 掉砂crush ofmold, crush 变形deformation,casting distortion, warped casting B. 缩孔（由凝固收缩引起) 缩孔shrinkage,shrinkaged cavity 内部缩孔internalshrinkage, dispersed shrinkage, blind shrinkage 敞露缩孔open shrinkage,external shrinkages, sink marks, depression 缩松porosity, shrinkage porosity,leakers, micro shrinkage, disperded shrinkage 缩陷sink marks,draw, suck-in 芯面缩孔core shrinkage 内角缩孔cornershrinkage, fillet shrinkage 出汗孔extruded bead,exudation 线状缩孔fissure likeshrinkage C. 气体缺陷（由气体引起的孔） 气孔blowholes,gas hole, blow 针孔pinholes 裂纹状缺陷，线状缺陷fissure defects D. 裂纹 裂纹crack 缩裂shrinkage crack 季裂seasoncracking, season crack 应力热裂hot cracking,hot tearing, hot tear 淬火裂纹quench crack,quenching crack 应力冷裂cold cracking,breakage, cold tearing, cold tear 龟裂crack 激冷层裂纹，白裂chill crack E. 夹杂物 夹渣slaginclusion, slag blowholes 砂眼sandinclusion, raised sand, sand hole

铸造缺陷中英文对照

A .尺寸，形状缺陷 铸造缺陷casting defects 尺寸超差impropershrinkage allowance 尺寸不合格wrong size 模样错误excess rappingof pattern, deformed pattern, pattern error 壁厚不均differentthickness 铸型下垂mold sag 错型mold shift,shift, miss-match, cross-joint 舂移ram off, ramaway 塌型mold drop,drop off, drop out, drop sticker 上型下沉，沉芯sag( 上型和型芯下垂导致壁厚减小） 飞翅fins, joint flash 翘曲warp age,buckling, warping, camber 铸件变形warped casting 挤箱push up,cramp-off 型裂broken mold,cracked 掉砂crush ofmold, crush 变形deformation,casting distortion, warped casting B.缩孔（由凝固收缩引起) 缩孔shrinkage,shrinkaged cavity 内部缩孔internalshrinkage, dispersed shrinkage, blind shrinkage

敞露缩孔open shrinkage,external shrinkages, sink marks, depression 缩松porosity, shrinkage porosity,leakers, micro shrinkage, disperded shrinkage 缩陷sink marks,draw, suck-in 芯面缩孔core shrinkage 内角缩孔cornershrinkage, fillet shrinkage 出汗孔extruded bead,exudation 线状缩孔fissure likeshrinkage C.气体缺陷（由气体引起的孔） 气孔blowholes,gas hole, blow 针孔pinholes 裂纹状缺陷，线状缺陷fissure defects D.裂纹 裂纹crack 缩裂shrinkage crack 季裂seasoncracking, season crack 应力热裂hot cracking,hot tearing, hot tear 淬火裂纹quench crack,quenching crack 应力冷裂cold cracking,breakage, cold tearing, cold tear 龟裂crack 激冷层裂纹，白裂chill crack