dm368-ipnc启动信息

DM36x initialization passed!
TI UBL Base Version: 1.50
Boot Loader BootMode = NAND
Starting NAND Copy...
Valid magicnum, 0xA1ACED66, found in block 0x00000008.
Boot Mode Task Completed

IPNC UBL Version: 1.1.0
Platform: DM368

Jumping to entry point at 0x81080000

U-Boot 1.3.4 (Feb 23 2012 - 13:49:47) DM368-IPNC-1.0.1

I2C: ready
DRAM: 128 MB
NAND: NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
Bad block table found at page 65504, version 0x00
Bad block table found at page 65472, version 0x00
32 MiB
*** Warning - bad CRC or NAND, using default environment

In: serial
Out: serial
Err: serial
ARM Clock :- 432MHz
DDR Clock :- 340MHz
Ethernet PHY: GENERIC @ 0x01
Hit any key to stop autoboot: 4  3  2  1  0

Loading from NAND 32MiB 3,3V 8-bit, offset 0x500000
Image Name: Linux-2.6.18_pro500-davinci_IPNC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1809708 Bytes = 1.7 MB
Load Address: 80008000
Entry Point: 80008000
## Booting kernel from Legacy Image at 80700000 ...
Image Name: Linux-2.6.18_pro500-davinci_IPNC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1809708 Bytes = 1.7 MB
Load Address: 80008000
Entry Point: 80008000
Verifying Checksum ... OK
Loading Kernel Image ... OK
OK

Starting kernel ...

Linux version 2.6.18_pro500-davinci_IPNC_DM368_2.6.0 (kudva@https://www.sodocs.net/doc/926257210.html,) (gcc version 4.2.0 20070126 (prerelease) (MontaVista 4.2.0-3.0.0.0702771 2007-03-10)) #1 PREEMPT Fri Mar 4 21:43:44 IST 2011
CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=00053177
Machine: DaVinci DM368 IPNC
Memory policy: ECC disabled, Data cache writeback
DaVinci DM0365 variant 0x0
PLL0: fixedrate: 24000000, commonrate: 170000000, vpssrate: 340000000
PLL0: vencrate_sd: 75555555, ddrrate: 340000000 mmcsdrate: 48571428
PLL1: armrate: 432000000, voicerate: 20571428, vencrate_hd: 27000000
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 8192 bytes, associativity 4, 32 byte lines, 64 sets
Built 1 zonelists. Total pages: 12288
Kernel command line: mem=48M console=ttyS1,115200n8 root=/dev/mtdblock3 rootfstype=cramfs ip=192.168.14.168:192.168.14.28:192.168.14.254:255.255.255.0:::off eth=$(ethaddr)
PID hash table entries: 256 (order: 8, 1024 bytes)
Clock event device timer0_0 configured with caps set: 07
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 48MB = 48MB total
Memory: 44684KB available (3105K code, 643K data, 180K init)
Security Framework v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
DaVinci: 104 gpio irqs
MUX: initialized GPIO20
MUX: initialized I2C_SCL

Generic PHY: Registered new driver
ch0 default output "COMPOSITE", mode "NTSC"
VPBE Encoder Initialized
SCSI subsystem initialized
NET: Registered protocol family 2
IP route cache hash table entries: 512 (order: -1, 2048 bytes)
TCP established hash table entries: 2048 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 2048 bind 1024)
TCP reno registered
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
squashfs: version 3.1 (2006/08/19) Phillip Lougher
JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc.
yaffs Mar 4 2011 21:40:50 Installing.
SGI XFS with no debug enabled
Initializing Cryptographic API
io scheduler noop registered
io scheduler anticipatory registered (default)
LTT : ltt-facilities init
LTT : ltt-facility-core init in kernel
DAVINCI-WDT: DaVinci Watchdog Timer: heartbeat 60 sec
Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
serial8250.0: ttyS0 at MMIO map 0x1c20000 mem 0xfbc20000 (irq = 40) is a 16550A
serial8250.0: ttyS1 at MMIO map 0x1d06000 mem 0xfbd06000 (irq = 41) is a 16550A
RAMDISK driver initialized: 1 RAM disks of 32768K size 1024 blocksize
Linux video capture interface: v2.00
Trying to register davinci display video device.
layer=c060da00,layer->video_dev=c060db60
Trying to register davinci display video device.
layer=c060d800,layer->video_dev=c060d960
davinci_init:DaVinci V4L2 Display Driver V1.0 loaded
i2c /dev entries driver
nand_davinci nand_davinci.0: Using 4-bit hardware ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0x75 (Samsung NAND 32MiB 3,3V 8-bit)
Creating 6 MTD partitions on "nand_davinci.0":
0x00000000-0x00300000 : "bootloader"
0x00300000-0x00500000 : "params"
0x00500000-0x00700000 : "kernel"
0x00700000-0x01f00000 : "filesystem"
0x01f00000-0x02100000 : "data1"
mtd: partition "data1" extends beyond the end of device "nand_davinci.0" -- size truncated to 0x100000
0x02100000-0x02000000 : "data2"
mtd: partition "data2" is out of reach -- disabled
nand_davinci nand_davinci.0: hardware revision: 2.3
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc intf: proc
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc intf: dev (254:0)
rtc_davinci_dm365 rtc_davinci_dm365.0: rtc core: registered rtc_davinci_dm365 as rtc0
Advanced Linux Sound Architecture Driver Version 1.0.12rc1 (Thu Jun 22 13:55:50 2006 UTC).
ASoC version 0.13.1
CQ0093 Voice Codec 0.1
asoc: cq93vc <-> davinci-vcif mapping ok
ALSA device list:
#0: On-chip voice codec (cq93vc)
IPv4 over IPv4 tunneling driver
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
rtc_davinci_dm365 rtc_davinci_dm365.0: setting the system clock to 2000-01-01 00:08:26 (946685306)
Time: timer0_1 clocksource has been instakiccinnIP-Config: No network devices available.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing init memory: 180K
INIT: version 2.86 b

ooting0
mkdir: Cannot create directory `/dev/.test': Read-only file system
Starting the hotplug events dispatcher: udevd.
Synthesizing the initial hotplug events...done.
Waiting for /dev to be fully populated...done.
0
CSL: Module install successful, device major num = 253
CSL: Module version 0.10.00, built on Mar 4 2011 21:46:09
I2C: Module install successful, device major num = 252
DMA: Module install successful, device major num = 251
DRV: Module install successful
DRV: Module built on Mar 4 2011 21:46:11
DRV: EDMACC.QUEPRI = 00000777
DRV: SYSTEM.MSTPRI0 = 00440022
DRV: SYSTEM.MSTPRI1 = 00000244
DRV: ISP.BCR = 00000002
DRV: SYSTEM.MISC = 00000399
CMEMK module: built on Mar 4 2011 at 21:45:45
Reference Linux version 2.6.18
File /home/kudva/workdir/DM365/IPNetCam/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/cmem/src/module/cmemk.c
allocated heap buffer 0xc4000000 of size 0x5000000
CMEM Range Overlaps Kernel Physical - allowing overlap
CMEM phys_start (0x1000) overlaps kernel (0x80000000 -> 0x83000000)
cmemk initialized
EDMAK module: built on Mar 4 2011 at 21:45:47
Reference Linux version 2.6.18
File /home/kudva/workdir/DM365/IPNetCam/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/edma/src/module/edmak.c
IRQK module: built on Mar 4 2011 at 21:45:48
Reference Linux version 2.6.18
File /home/kudva/workdir/DM365/IPNetCam/dvsdk_2_10_01_18/linuxutils_2_24_03/packages/ti/sdo/linuxutils/irq/src/module/irqk.c
irqk initialized
Creat queue id:0
queue id:0
FileMngThread created
Creat queue id:32769
queue id:32769
AlramThread created
Share memory init success
IPNC_DM368_2.6.0 (kudva@https://www.sodocs.net/doc/926257210.html,) (gcc version
Creat queue id:65538
queue id:65538
queue id:32769
queue id:65538
Creat queue id:98307
queue id:98307
Starting mounting local filesystems: mount none on /dev/shm type tmpfs (rw,size=5M)
none on /var/run type tmpfs (rw)
none on /tmp type tmpfs (rw,sync)
Setting up networking ...rm: unable to remove `/etc/network/run': Read-only file system

CPU is DM368
./av_server.out DM368 NTSC APPRO2A AEWB 720P H264 5000000 VBR AUTO MENUOFF &
CPU CurrentStatus is = 1
Check_device_version : DEVICE VER = 1 !!
Starting hotplug subsystem:
ApproDrvInit: 7
Creat queue id:131076
queue id:131076
pci
pci [success]

AVSERVER UI: Initializing.
usb

CLK Hz,
ARM Hz = 432000000
DDR Hz = 340000000
VPSS Hz = 340000000
IMCOP Hz = 340000000

[OSA_FILE ] Reading file [/mnt/nand/IMG_Paramset.bin] ... ERROR IMAGE TUNE: Paramset File is not available..... Setting DEFAULT parameter

CONFIGURING AVSERVER FOR DM368 .....
queue id:65538
SENSOR FPS VALUE = 30
queue id:131076
DavinciDisplay DavinciDisplay.1: Before finishing with S_FMT:
layer.pix_fmt.bytesperline = 640,
layer.pix_fmt.width = 640,
layer.pix_fmt.height = 480,
layer.pix_fmt.sizeimage =460800
FR : 0 usersDavinciDisplay Davinci

Display.1: pixfmt->width = 640,
layer->layer_info.config.line_length= 640
registered from exsiting face album
IPNC_DM368_2.6.0 (kudva@https://www.sodocs.net/doc/926257210.html,) (gcc version
IPNC AUTO_IRIS = 1
usb [success]
isapnp
isapnp [success]
APPRO AEW TRIAL VERSION !!!
APPRO AEW DATE LINE 2011/12
ide
ide [success]
input
input [success]
scsi
scsi [success]
done.
Starting portmap daemon: portmapSimple mixer control 'PGA',0
Capabilities: cvolume
Capture channels: Mono
Limits: Capture 0 - 3
Mono: Capture 2 [67%]
.
Simple mixer control 'Mono DAC',0
Capabilities: pvolume pvolume-joined
Playback channels: Mono
Limits: Playback 0 - 63
Mono: Playback 47 [75%]
SystemInit success
Schedule manager init success
Starting internet superserver: inetd.
io scheduler deadline registered
io scheduler cfq registered
TI DaVinci EMAC: kernel boot params Ethernet address: $(ethaddr)
sbulla: unknown partition table
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
loop: loaded (max 8 devices)
tun: Universal TUN/TAP device driver, 1.6
tun: (C) 1999-2004 Max Krasnyansky
CSLIP: code copyright 1989 Regents of the University of California
netconsole: not configured, aborting
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
Davinci EMAC MII Bus: probed
MAC address is $(ethaddr)
TI DaVinci EMAC Linux version updated 4.0
davinci-mmc davinci-mmc.0: Supporting 4-bit mode
davinci-mmc davinci-mmc.0: Using DMA mode
usbcore: registered new driver usbfs
usbcore: registered new driver hub
musb_hdrc: version 6.0, cppi-dma, peripheral, debug=0
musb_hdrc musb_hdrc: No DMA interrupt line
musb_hdrc: USB Peripheral mode controller at c38f8000 using DMA, IRQ 12
Loading iSCSI transport class v1.1-646.<5>iscsi: registered transport (tcp)
sbulla: unknown partition table
mkdosfs 3.0.6 (04 Oct 2009)
unable to get drive geometry, using default 255/63
/dev/sbulla has 255 heads and 63 sectors per track,
logical sector size is 512,
using 0xf8 media descriptor, with 1024 sectors;
file system has 2 12-bit FATs and 4 sectors per cluster.
FAT size is 1 sector, and provides 247 clusters.
Root directory contains 512 slots.
Volume ID is 58c4fbb6, no volume label.
queue id:0
umount: /mnt/mmc: not mounted
killall: dhcpcd: no process killed
rm: cannot remove `/var/run/dhcpcd-eth0.pid': No such file or directory
net_search_gateway:eth0, EA8C0, 0, 1
dns=192.168.14.1
net_search_gateway:eth0, EA8C0, 0, 1
net_search_gateway:eth0, 0, FE0EA8C0, 3
dns=192.168.14.1
ERROR: Module g_g_file_storage gadget: File-backed Storage Gadget, version: 28 November 2005
file_storage doeg_file_storage gadget: Number of LUNs=1
s not exist in /g_file_storage gadget-lun0: ro=0, file: /dev/sbulla
proc/modules
system_server/516[CPU#0]: BUG in local_bh_enable at kernel/softirq.c:196
ApproDrvInit: 9
queue id:131076
Initializing...
ApproDrv

Init: 8
queue id:131076
Initializing...
ApproDrvInit: 2
queue id:131076
Initializing...
ApproDrvInit: 6
queue id:131076
Initializing...
ApproDrvInit: 10
queue id:131076
Initializing...
ApproDrvInit: 3
queue id:131076
queue id:0
queue id:32769
...done initializing
Play this stream using the URL:
rtsp://192.168.14.168:8554/PSIA/Streaming/channels/1?videoCodecType=MPEG4
...done initializing
Play this stream using the URL:
rtsp://192.168.14.168:8557/PSIA/Streaming/channels/2?videoCodecType=H.264
...done initializing
Play this stream using the URL:
rtsp://192.168.14.168:8555/PSIA/Streaming/channels/0?videoCodecType=MJPEG
...done initializing
Play this stream using the URL:
rtsp://192.168.14.168:8556/PSIA/Streaming/channels/2?videoCodecType=H.264
[01/Jan/2000:00:08:47 +0000] boa: server version Boa/0.94.13
[01/Jan/2000:00:08:47 +0000] boa: server built Mar 4 2011 at 21:48:04.
[01/Jan/2000:00:08:47 +0000] boa: starting server pid=780, port 80
queue id:0
...done initializing
Play this stream using the URL:
rtsp://192.168.14.168:8553/PSIA/Streaming/channels/1?videoCodecType=MPEG4
UDPString=uuid:Upnp-TVEmulator-1_0-00_0079959453

Upnp port is 0
UPnP Initialized OK ip=192.168.14.168, port=49152
desc_doc_url = http://192.168.14.168/tvdevicedesc.xml
INIT: Entering runlevel: 3device advertisement succeed.
MontaVista(R) Linux(R) Professional Edition 5.0.0 (0702774)
DM368_IPNC login: