Page 4
?
Small size and lightweight
? Suitable for both flow and reflow soldering ?
Reduction of assembly costs and matching with placement machines
2007 - 2008
Standard: 2%, 5%, 10%---E 24 series 1%---E 96 series
2007 - 2008 Page 5
Marking on the Resistors Body:
?For 0402 size, no marking on the body due to the small size of the resistor.
?±5% tolerance product. (Including resistance values less than 1?; both 1% and 5%) The marking is 3 digits, the first 2 digits are the significant figures of the resistance and the 3rd digit denotes number of zeros.
153 = 15000? = 15K?; 120 = 12? Below 10? shown as this: 6R8 = 6.8? 0.1?~0.99? shown as this: R33 = 0.33?
?±1% tolerance marking of case size 0805 and bigger is 4 digits, the first 3 digits are the significant figures of the resistance and the 4th digit denotes number of zeros.
2372 = 23700? = 23.7K?; 1430 = 143? Below 10? shown as this: 3R24 = 3.24?0.1?~0.99? shown as this: R33 = 0.33?
Page 6
2007 - 2008
* More details, please see pages 78-79.
? Standard E-96 series values (±1% tolerance) of 0603 size. Due to the small size of the resistor’s body, 3 digits
marking will be used to indicate the accurate resistance value by using the Multiplier code & Standard E-96 Series Resistance Value Code as shown on Page 6.
1.96K ? = 196 x 101 ? = 29B
12.4? = 124 x 10-1 ? = 10X
? Standard E-24 series values which does not belong to E-96 series values (in ±1% tolerance) of 0603 size. The marking is the same as 5% tolerance but marked with underline.
122 = 1200 = 1.2K ?
680 = 68?
Temperature coefficient
±5%: 1? ~ 10M ? ≤ ±200PPM/°C
±1%: 10? ~ 100? ≤ ±200PPM/°C; 101? ~ 1M ? ≤ ±100PPM/°C Short-time overload ±5%: ±(2.0% + 0.1?) Max. ±1%: ±(1.0% + 0.1?) Max. Insulation resistance
Min. 1,000 Mega Ohm
Dielectric withstanding voltage
No evidence of flashover, mechanical damage, arcing or insulation breakdown Terminal bending ±(1.0% + 0.05?) Max.
Soldering heat Resistance change rate is ±(1.0% + 0.05?) Max. Solderability
Min. 95% coverage Temperature cycling ±5%: ±(1.0% + 0.05?) Max. ±1%: ±(0.5% + 0.05?) Max. Humidity (Steady State) ±5%: ±(3.0% + 0.1?) Max. ±1%: ±(0.5% + 0.1?) Max. Load life in humidity
±5%: ±(3.0% + 0.1?) Max. ±1%: ±(1.0% + 0.1?) Max. Load life
±5%: ±(3.0% + 0.1?) Max.
±1%: ±(1.0% + 0.1?) Max.
* The values which are not of standard E-24 series (2% & 5%) and not of E-96 series (1%) could be offered on a case to case basis.
2007 - 2008
Page 7
?
16P8 (16Pin 8R)
THICK FILM CHIP RESISTOR ARRAYS
?High density 2, 4, 8 resistors in one small case (convex type)
?Improvement of placement efficiency
?Packaging is suitable for automatic placement machines
? Superior solderability
? Scalloped
?2D02 (4Pin 2R)?4D02, 4D03 (8Pin 4R)
?10P8 (10Pin 8R)
Part No.Style L W H?1?2P Q 2D02
(0402x2)
2D02
(4Pin 2R)
1.0 ± 0.1 1.0 ± 0.1 0.35 ± 0.1 0.17 ± 0.1 0.25 ± 0.1 0.65 ± 0.05 0.33 ± 0.1
4D02
(0402x4)
4D02
(8Pin 4R)
2.0 ± 0.1 1.0 ± 0.1 0.45 ± 0.1 0.2 ± 0.15 0.3 ± 0.15 0.5 ± 0.05 0.3 ± 0.05
4D03
(0603x4)
4D03
(8Pin 4R)
3.2 ± 0.2 1.6 ± 0.2 0.5 ± 0.1 0.3 ± 0.15 0.3 ± 0.15 0.8 ± 0.1 0.5 ± 0.15
16P8
16P8
(16Pin 8R)
4.0 ± 0.2 1.6 ± 0.15 0.45 ± 0.1 0.3 ± 0.15 0.4 ± 0.15 0.5 ± 0.05 0.3 ± 0.05
10P8
10P8
(10Pin 8R)
3.2 ± 0.2 1.6 ± 0.15 0.55 ± 0.1 0.4 ± 0.1 0.3 ± 0.15 0.64 ± 0.05 0.35 ± 0.05
Resistance Range
Part No.Style
Power
Rating
at 70oC
Max.
Working
Voltage
Max.
Overload
Voltage
Dielectric
With-
standing
Voltage
Operated
Temp.
Range F (±1%)
E-96 series
J (±5%)
E-24 series
Jumper
Rated
Current 2D02
2D02
(4Pin2R) 1/16W 50V 100V 500V
-55oC~+155oC - 10?~ 1M? - 4D02
4D02
(8Pin4R) 1/16W 50V 100V 500V
-55oC~+155oC - 10?~ 1M? - 4D03
4D03
(8Pin4R) 1/16W 50V 100V 500V
-55oC~+155oC
100?~560K? 10?~ 1M? 1A 16P8
16P8
(16Pin8R) 1/16W 50V 100V 100V
-55oC~+155oC - 10?~ 1M? - 10P8
10P8
(10Pin8R) 1/32W 25V 50V 50V -55oC~+155oC - 33?~ 100K? - Note: Part number and ordering procedure the same as Thick Film Chip Resistors on Page 4.
Standard: 2%, 5%, 10%---E 24 series
1%---E 96 series
2007 - 2008 Page 8