1#
2#
3#
4#
5#
6#
7#
HN
H1
H2
H3
H4
H5
H6
g g
mm
s
KN
KN
KN
Residence Time = Barrel Capacity / Shot Size x Cycle Time 驻留时间=融胶能力÷单啤重量×注塑周期
If Residence Time is greater than 7 x cycle time then a stepped temp profile is required 如果驻留时间大于7×周期,那么一个阶梯型的温度分布式必要的。For T2, T3…Add tabs for additional process sheets 对于T2,T3……请增加表格用于额外的工艺表
KPL Process Engineer:KPI Process Engineer:
KPL 工艺工程师
KPL 工艺工程师
KPI-PRC Program Manager:KPI-NA Tooling Engineer:KPL-中国 工艺工程师KPL-北美 工艺工程师
℃
℃
Speed 速度
1st Stage 4th stage Date of Trial : 试作时间:
Process Sheet 参数表
Keen Point International
Customer 客户:Prepared by : 编写人:
Trial Times :试作次数:Parameters 参数
Machine Num. 机台编号
Effective date
生效期
No.of Cavity
型腔数量
Part Num:品番.:
Mold Maker :
制模人
Part Name :品名:
Mold Number : 模具编号:
Program :项目:
Approved by : 确认:
Resin 材料
Grade/Colour 牌号/颜色
Machine Type 机台型号Injection 注射Pressure 压力(bar)
Position(mm)
位置
Packing 保压Pressure 压力
(bar)
Speed 速度(mm/s)
time 时间 (s)Screw 储料Pressure 压力(bar)Speed 转速(RPM)Position 位置(mm)
2nd Stage 2nd stage 3rd stage 2nd stage 1st stage 1st stage 4th stage
4th stage 3rd stage 3rd stage 6th stage 5th stage 5th stage
Position 位
置(mm)
1st Stage 1st stage 1st stage push 第一段顶出Pressure 压力(bar)Speed 速度Close Mold
合模Pressure 压力(bar)Speed 速度Position 位置(mm)Open Mold
开模
Pressure
压力(bar)Speed 速度Position 位置 (mm)
Ejection Sys 顶出系统3rd Stage 3rd stage Ejector Stroke 顶出行程2nd Stage 2nd stage 2nd stage push 第二段顶0
High pres
5th stage
1st stage pull 第一段退顶针3#4#5#6#Hot Runner Manifold Temp. 热流道温度Hot Nozzle 热嘴
Low pres 4th stage 2nd stage pull 第一段退顶针
8#
Manifold 流道板1#2#7#8#
Thermolator 模温机
Cavity 型腔
Core 型芯
Slide 行位
Lifter 斜顶
℃
℃
Actual
实际
Barrel Temp 螺杆温度
Actual 实际Setting 设置℃
s Injection time 注射时间
Mold Temp.
模温
Settin g 设置Actual 实际Setting 设置Actual 实际Setting 设置Drying Temp&Time 烤料温度&时间
Residence Time 驻留时间 (sec)Barrel Cap (g)融胶能力
Shot weight 整
啤重量 Cooling time 冷却时间
Runner weight 水口重量
s Press style 压力方式:
Position 位置
Time 时间
Pressure 压力(bar)
Transfer
V-P 保压切换
Clamping force
锁模力
s
Cushion 缓冲
Low pres 最小压力
High pres 最大压力
m m
Cycle time 周期
Remark 备注
bar
Clamp Data 锁模资料
KPI - 331