毕业设计混凝土桥梁结构形式(中英文翻译)

混凝土梁桥的结构形式

事实证明，预应力混凝土结构是在技术上先进、经济上有竞争力、符合审美学的一种先进技术。从使用标准组成的小跨径桥梁到吊梁和跨径将近100英尺的连续箱梁桥，几乎所有的混凝土桥梁，甚至于相对短时间的桥梁都是预应力结构的。采用预制、现场浇筑或两种方法并用。在同一工程中经常同时使用先张法和后张法。

在美国，公路桥一般情况下必须满足荷载、设计和AASHTO规定的建设的要求。对于服务于其它目的步行街和桥梁的设计要求由当地的或地方的代码建立。ACI代码的备注也被纳入参考。

伴随最小交通中断的大约100英尺的跨径的桥梁由提供低的初级预算，最小量维修和养护费用和快速的简易的预制板组成。这种梁一般是用先张法。预制板一块挨一块的放置并且在相邻的预制板间受剪的缝隙填满不收缩的灰泥之后，经常在中间横膈膜的位置后张拉。对于公路，用沥青铺设的表面可以直接用在预制混凝土的上面。在某些情况下，一块放置在正确位置的现浇板提供复合作用。

空心板一般用于深度15英尺到21英尺，宽度3英尺或4英尺。对于一个标准HS20的公路，空心板适合于大约50 英尺的跨径。标准渠化区段在多种宽度，深度从21英尺到35英尺时是有利的，可用于大约20英尺到60英尺的跨径。中空的箱形梁和T形梁用于大约100英尺的长跨径。

对于中等跨径的大约120英尺的公路桥，一般使用AASHTO 标准梁。它们和一种复合现场预制行车道板一起使用。在板被安置之后，这样的梁经常在预浇梁的先张拉与合成梁的后张拉后结合。试图获得改进经济，一些国家已经采用更精炼的设计，例如华盛顿州标准梁。

经过特别设计预制建筑梁可以用来携带一个单轨铁路系统。完成的沃尔特迪斯尼乐园单轨铁路的一系列的特征, 每个包括六个单独支持的预拉梁，一起形成连续结构。典型的跨距是100到110英尺。被使用的337根梁，大约一半有垂直与水平曲率和易变超级升高的一些结合。所有的梁是中空的，它的特征是通过在曲梁中插入泡沫和在直梁制作中移动形心轴获得。

由于运输问题和构件垂直的大而重的问题，预制梁不能用于跨径超过120英尺的桥梁。另一方面，桥梁有一种向大跨径发展的明显趋势。对于提高的都市高速道路来说，大跨径促进通路而且将对下面的活动妨碍减到最少。对环境的损害问题的关心，导致连续高架桥大跨径的选择。对于跨河桥，因为航行间隙的需求，中间可能不可以搭设桥墩。

在这一个类型的典型建筑中，桥墩（台）采用现场预制, 经常使用滑动的技术。一个箱梁的" 锤头"浇筑在桥墩的顶端, 并且通过平衡的悬臂方法控制每个方向的建筑进

行。最后,在完成跨中结合处的浇筑之后, 这种结构对于完全连续性的桥梁来说是进一步的受拉的。修剪钥匙可能被用在片段之间垂直面之上, 而且预制建筑与环氧基树脂黏在一起。

想象的工程学藉着许多特别的技术示范已经延长混凝土建筑的范围，就桥梁而言，已经远远超过几年以前可以想象的到的任何事。在美国，双向弯曲的现场浇铸的部分箱梁已经成功地完成310 英尺的跨距，跨越了北加州的鳗鱼河。该桥的中间跨度550英尺，侧跨跨度390英尺，初步设计已经完成。

预应力混凝土桥梁很适合于大跨径的另一种形式是悬索箱梁。一个值得注意的例子是阿根廷境内的Chaco-Corrientes桥。桥的主跨径804英尺，由两个A型构架塔支撑，悬索从塔顶到沿着底板伸展。受拉的悬索不仅提供一种垂直反应组成支撑底板，而且对于箱梁产生水平的压缩，增加构件中的张拉力。

许多年以前德国工程师Ulrich Finsterwalder 提出适合于负担荷载和大跨径的一个结构类型是压带式桥。压带是桥运输跨越莱茵河的一个管道和人行道，跨径446英尺。上部结构的施工顺序是（a）垂直的一对悬索，(b)在每个悬索的下面，安置预制板形成一人行道甲板和一U型的平台, 并且(c)在附近现场浇注混凝土。放置在顶部的管道支撑在扶手的顶部，向一边倾斜，大幅地增加结构的主要风速。

讨论桥梁形式应适当的考虑结构的美学。当结构可能根据最小的费用和技术设计的时候，时间消逝了。特别是桥梁结构到处可见。生产视觉上不愉快的结构, 过去经常发生, 是一种不负专业责任的行为。特别地对于主要的跨距，还有一些比较普通的结构来说，应该在设计过程的概念阶段寻找建筑的建议。

出处：

安瑞克．混凝土桥梁结构形式[J]．建筑实录(美)，2010，33(36)：34—36

The Structure of Concrete Bridge

Pre-stressed concrete has proved to be technically advantageous, economically competitive, and esthetically superior bridges, from very short span structures using standard components to cable-stayed girders and continuous box girders with clear spans of nearly 100aft .Nearly all concrete bridges, even those of relatively short span, are now pre-stressed. Pre-casting, cast-in-place construction, or a combination of the two methods may be used .Both pre-tensioning and post tensioning are employed, often on the same project.

In the United States, highway bridges generally must-meet loading ,design ,and construction requirements of the AASHTO Specification .Design requirements for pedestrian crossings and bridges serving other purposes may be established by local or regional codes and specifications .ACI Code provisions are often incorporated by reference .

Bridges spans to about 100ft often consist of pre-cast integral-deck units ,which offer low initial cost ,minimum ,maintenance ,and fast easy construction ,with minimum traffic interruption .Such girders are generally pre-tensioned .The units are placed side by side ,and are often post-tensioned laterally at intermediate diaphragm locations ,after which shear keys between adjacent units are filled with non-shrinking mortar .For highway spans ,an asphalt wearing surface may be applied directly to the top of the pre-cast concrete .In some cases ,a cast-in-place slab is placed to provide composite action .

The voided slabs are commonly available in depths from 15 to 21 in .and widths of 3 to 4 ft .For a standard highway HS20 loading, they are suitable for spans to about 50 ft, Standard channel sections are available in depths from 21 to 35 in a variety of widths, and are used for spans between about 20 and 60 ft .The hollow box beams-and single-tee girders are intended for longer spans up to about 100 ft.

For medium-span highway bridges ,to about 120 ft ,AASHTO standard I beams are

generally used .They are intended for use with a composite cast-in-place roadway slab .Such girders often combine pre-tensioning of the pre-cast member with post-tensioning of the composite beam after the deck is placed .In an effort to obtain improved economy ,some states have adopted more refined designs ,such as the State of Washington standard girders.

The specially designed pre-cast girders may be used to carry a monorail transit system .The finished guide way of Walt Disney World Monorail features a series of segments, each consisting of six simply supported pre-tensioned beams ,together to from a continuous structure .Typical spans are 100 to 110 ft . Approximately half of the 337 beams used have some combination of vertical and horizontal curvatures and variable super elevation .All beams are hollow, a feature achieved by inserting a styro-foam void in the curved beams and by a moving mandrel in straight beam production.

Pre-cast girders may not be used for spans much in excess of 120 ft because of the problems of transporting and erecting large, heavy units.

On the other hand ,there is a clear trend toward the use of longer spans for bridges .For elevated urban expressways ,long spans facilitate access and minimize obstruction to activities below .Concern for environmental damage has led to the choice of long spans for continuous viaducts . For river crossings, intermediate piers may be impossible because of requirements of navigational clearance.

In typical construction of this type, piers are cast-in-place, often using the slip-forming technique .A ―hammerhead‖ section of box girder is often cast at the top of the pier, and construction proceeds in each direction by the balanced cantilever method. Finally, after the closing cast-in-place joint is made at mid-span, the structure is further post-tensioned for full continuity .Shear keys may be used on the vertical faces between segments, and pre-cast are glued with epoxy resin.

The imaginative engineering demonstrated by many special techniques has extended the range of concrete construction for bridges far beyond anything that could be conceived just a few years ago .In the United States, twin curved cast-in –place segmental box girders have recently been completed for of span of 310 ft over the Eel River in northern California .Preliminary design has been completed for twin continuous box girders consisting of central 550 ft spans flanked by 390 ft side spans.

Another form of pre-stressed concrete bridge well suited to long spans is the cable-stayed box girder .A notable example is the Chaco-Corrientes Bridge in Argentina .The bridges main span of 804 ft is supported by two A-frame towers, with cable stays stretching from tower tops to points along the deck .The deck itself consists of two parallel box girders made of pre-cast sections erected using the cantilever method .The tensioned cables not only

provide a vertical reaction component to support the deck ,but also introduce horizontal compression to the box girders ,adding to the post-tensioning force in those members .

Stress-ribbon Bridge pioneered many years ago by the German engineer Ulrich Finsterwalder. The stress-ribbon bridge carries a pipeline and pedestrians over the Rhine River with a span of 446 ft .The superstructure erection sequence was to (a) erect two pairs of cables, (b) place pre-cast slabs forming a sidewalk deck and a U under each of the sets of cables, and (c) cast-in-place concrete within the two Us. The pipeline is placed atop supports at railing height, off to one side, which greatly increases the wind speed of the structure.

It is appropriate in discussing bridge forms to mention structural esthetics .The time is past when structures could be designed on the basis of minimum cost and technical advantages alone .Bridge structures in particular are exposed for all to see .To produce a structure that is visually offensive ,as has occurred all too often in the past, is an act professional irresponsibility .Particularly for major spans ,but also for more ordinary structures ,architectural advice should be sought early in conceptual stage of the design process.

毕业设计外文翻译资料

外文出处： 《Exploiting Software How to Break Code》By Greg Hoglund, Gary McGraw Publisher : Addison Wesley Pub Date : February 17, 2004 ISBN : 0-201-78695-8 译文标题： JDBC接口技术 译文： JDBC是一种可用于执行SQL语句的JavaAPI（ApplicationProgrammingInterface应用程序设计接口）。它由一些Java语言编写的类和界面组成。JDBC为数据库应用开发人员、数据库前台工具开发人员提供了一种标准的应用程序设计接口，使开发人员可以用纯Java语言编写完整的数据库应用程序。 一、ODBC到JDBC的发展历程 说到JDBC，很容易让人联想到另一个十分熟悉的字眼“ODBC”。它们之间有没有联系呢？如果有，那么它们之间又是怎样的关系呢？ ODBC是OpenDatabaseConnectivity的英文简写。它是一种用来在相关或不相关的数据库管理系统（DBMS）中存取数据的，用C语言实现的，标准应用程序数据接口。通过ODBCAPI，应用程序可以存取保存在多种不同数据库管理系统（DBMS）中的数据，而不论每个DBMS使用了何种数据存储格式和编程接口。 1．ODBC的结构模型 ODBC的结构包括四个主要部分：应用程序接口、驱动器管理器、数据库驱动器和数据源。应用程序接口：屏蔽不同的ODBC数据库驱动器之间函数调用的差别，为用户提供统一的SQL编程接口。 驱动器管理器：为应用程序装载数据库驱动器。 数据库驱动器：实现ODBC的函数调用，提供对特定数据源的SQL请求。如果需要，数据库驱动器将修改应用程序的请求，使得请求符合相关的DBMS所支持的文法。 数据源：由用户想要存取的数据以及与它相关的操作系统、DBMS和用于访问DBMS的网络平台组成。 虽然ODBC驱动器管理器的主要目的是加载数据库驱动器，以便ODBC函数调用，但是数据库驱动器本身也执行ODBC函数调用，并与数据库相互配合。因此当应用系统发出调用与数据源进行连接时，数据库驱动器能管理通信协议。当建立起与数据源的连接时，数据库驱动器便能处理应用系统向DBMS发出的请求，对分析或发自数据源的设计进行必要的翻译，并将结果返回给应用系统。 2．JDBC的诞生 自从Java语言于1995年5月正式公布以来，Java风靡全球。出现大量的用java语言编写的程序，其中也包括数据库应用程序。由于没有一个Java语言的API，编程人员不得不在Java程序中加入C语言的ODBC函数调用。这就使很多Java的优秀特性无法充分发挥，比如平台无关性、面向对象特性等。随着越来越多的编程人员对Java语言的日益喜爱，越来越多的公司在Java程序开发上投入的精力日益增加，对java语言接口的访问数据库的API 的要求越来越强烈。也由于ODBC的有其不足之处，比如它并不容易使用，没有面向对象的特性等等，SUN公司决定开发一Java语言为接口的数据库应用程序开发接口。在JDK1．x 版本中，JDBC只是一个可选部件，到了JDK1．1公布时，SQL类包（也就是JDBCAPI）

桥梁工程毕业设计外文翻译箱梁

桥梁工程毕业设计外文翻译箱梁

西南交通大学本科毕业设计（论文） 外文资料翻译 年级: 学号: 姓名: 专业: 指导老师:

6 月

外文资料原文： 13 Box girders 13.1 General The box girder is the most ?exible bridge deck form. It can cover a range of spans from25 m up to the largest non-suspended concrete decks built, of the order of 300 m. Single box girders may also carry decks up to 30 m wide. For the longer span beams, beyond about 50 m, they are practically the only feasible deck section. For the shorter spans they are in competition with most of the other deck types discussed in this book. The advantages of the box form are principally its high structural ef?ciency (5.4), which minimises the prestress force required to resist a given bending moment, and its great torsional strength with the capacity this gives to re-centre eccentric live loads, minimising the prestress required to carry them.

毕业设计外文翻译附原文

外文翻译 专业机械设计制造及其自动化学生姓名刘链柱 班级机制111 学号1110101102 指导教师葛友华

外文资料名称： Design and performance evaluation of vacuum cleaners using cyclone technology 外文资料出处：Korean J. Chem. Eng., 23(6), (用外文写) 925-930 (2006) 附件： 1.外文资料翻译译文 2.外文原文

应用旋风技术真空吸尘器的设计和性能介绍 吉尔泰金，洪城铱昌，宰瑾李， 刘链柱译 摘要：旋风型分离器技术用于真空吸尘器 - 轴向进流旋风和切向进气道流旋风有效地收集粉尘和降低压力降已被实验研究。优化设计等因素作为集尘效率，压降，并切成尺寸被粒度对应于分级收集的50％的效率进行了研究。颗粒切成大小降低入口面积，体直径，减小涡取景器直径的旋风。切向入口的双流量气旋具有良好的性能考虑的350毫米汞柱的低压降和为1.5μm的质量中位直径在1米3的流量的截止尺寸。一使用切向入口的双流量旋风吸尘器示出了势是一种有效的方法，用于收集在家庭中产生的粉尘。 摘要及关键词：吸尘器; 粉尘; 旋风分离器 引言 我们这个时代的很大一部分都花在了房子，工作场所，或其他建筑，因此，室内空间应该是既舒适情绪和卫生。但室内空气中含有超过室外空气因气密性的二次污染物，毒物，食品气味。这是通过使用产生在建筑中的新材料和设备。真空吸尘器为代表的家电去除有害物质从地板到地毯所用的商用真空吸尘器房子由纸过滤，预过滤器和排气过滤器通过洁净的空气排放到大气中。虽然真空吸尘器是方便在使用中，吸入压力下降说唱空转成比例地清洗的时间，以及纸过滤器也应定期更换，由于压力下降，气味和细菌通过纸过滤器内的残留粉尘。 图1示出了大气气溶胶的粒度分布通常是双峰形，在粗颗粒（>2.0微米）模式为主要的外部来源，如风吹尘，海盐喷雾，火山，从工厂直接排放和车辆废气排放，以及那些在细颗粒模式包括燃烧或光化学反应。表1显示模式，典型的大气航空的直径和质量浓度溶胶被许多研究者测量。精细模式在0.18?0.36 在5.7到25微米尺寸范围微米尺寸范围。质量浓度为2?205微克，可直接在大气气溶胶和 3.85至36.3μg/m3柴油气溶胶。

桥梁专业外文翻译--欧洲桥梁研究

桥梁专业外文翻译--欧洲桥梁研究

附录 Bridge research in Europe A brief outline is given of the development of the European Union, together with the research platform in Europe. The special case of post-tensioned bridges in the UK is discussed. In order to illustrate the type of European research being undertaken, an example is given from the University of Edinburgh portfolio: relating to the identification of voids in post-tensioned concrete bridges using digital impulse radar. Introduction The challenge in any research arena is to harness the findings of different research groups to identify a coherent mass of data, which enables research and practice to be better focused. A particular challenge exists with respect to Europe where language barriers are inevitably very significant. The European Community was formed in the 1960s based upon a political will within continental Europe to avoid the European civil wars, which developed into World War 2 from 1939 to 1945. The strong political motivation formed the original community of which Britain was not a member. Many of the continental countries saw Britain’s interest as being purely economic. The 1970s saw Britain joining what was then the European Economic Community (EEC) and the 1990s has seen the widening of the community to a European Union, EU, with certain political goals together with the objective of a common European currency. Notwithstanding these financial and political developments, civil engineering and bridge engineering in particular have found great difficulty in forming any kind of common thread. Indeed the educational systems for University training are quite different between Britain and the European continental countries. The formation of the EU funding schemes —e.g. Socrates, Brite Euram and other programs have helped significantly. The Socrates scheme is based upon the exchange of students between Universities in different member states. The Brite Euram scheme has involved technical research grants given to

软件开发概念和设计方法大学毕业论文外文文献翻译及原文

毕业设计（论文）外文文献翻译 文献、资料中文题目：软件开发概念和设计方法文献、资料英文题目： 文献、资料来源： 文献、资料发表（出版）日期： 院（部）： 专业： 班级： 姓名： 学号： 指导教师： 翻译日期： 2017.02.14

外文资料原文 Software Development Concepts and Design Methodologies During the 1960s, ma inframes and higher level programming languages were applied to man y problems including human resource s yste ms,reservation s yste ms, and manufacturing s yste ms. Computers and software were seen as the cure all for man y bu siness issues were some times applied blindly. S yste ms sometimes failed to solve the problem for which the y were designed for man y reasons including: ?Inability to sufficiently understand complex problems ?Not sufficiently taking into account end-u ser needs, the organizational environ ment, and performance tradeoffs ?Inability to accurately estimate development time and operational costs ?Lack of framework for consistent and regular customer communications At this time, the concept of structured programming, top-down design, stepwise refinement，and modularity e merged. Structured programming is still the most dominant approach to software engineering and is still evo lving. These failures led to the concept of "software engineering" based upon the idea that an engineering-like discipl ine could be applied to software design and develop ment. Software design is a process where the software designer applies techniques and principles to produce a conceptual model that de scribes and defines a solution to a problem. In the beginning, this des ign process has not been well structured and the model does not alwa ys accurately represent the problem of software development. However,design methodologies have been evolving to accommo date changes in technolog y coupled with our increased understanding of development processes. Whereas early desig n methods addressed specific aspects of the

机械毕业设计英文外文翻译399驱动桥

附录A 英文文献 Drive Axle All vehicles have some type of drive axle/differential assembly incorporated into the driveline. Whether it is front, rear or four wheel drive, differentials are necessary for the smooth application of engine power to the road. Powerflow The drive axle must transmit power through a 90°angle. The flow of power in conventional front engine/rear wheel drive vehicles moves from the engine to the drive axle in approximately a straight line. However, at the drive axle, the power must be turned at right angles (from the line of the driveshaft) and directed to the drive wheels. This is accomplished by a pinion drive gear, which turns a circular ring gear. The ring gear is attached to a differential housing, containing a set of smaller gears that are splined to the inner end of each axle shaft. As the housing is rotated, the internal differential gears turn the axle shafts, which are also attached to the drive wheels. Rear-wheel drive Rear-wheel-drive vehicles are mostly trucks, very large sedans and many sports car and coupe models. The typical rear wheel drive vehicle uses a front mounted engine and transmission assemblies with a driveshaft coupling the transmission to the rear drive axle. Drive in through the layout of the bridge, the bridge drive shaft arranged vertically in the same vertical plane, and not the drive axle shaft, respectively, in their own sub-actuator with a direct connection, but the actuator is located at the front or the back of the adjacent shaft

毕业设计英文翻译

使用高级分析法的钢框架创新设计 1．导言 在美国，钢结构设计方法包括允许应力设计法(ASD)，塑性设计法(PD)和荷载阻力系数设计法(LRFD)。在允许应力设计中，应力计算基于一阶弹性分析，而几何非线性影响则隐含在细部设计方程中。在塑性设计中，结构分析中使用的是一阶塑性铰分析。塑性设计使整个结构体系的弹性力重新分配。尽管几何非线性和逐步高产效应并不在塑性设计之中，但它们近似细部设计方程。在荷载和阻力系数设计中，含放大系数的一阶弹性分析或单纯的二阶弹性分析被用于几何非线性分析，而梁柱的极限强度隐藏在互动设计方程。所有三个设计方法需要独立进行检查，包括系数K计算。在下面，对荷载抗力系数设计法的特点进行了简要介绍。 结构系统内的内力及稳定性和它的构件是相关的，但目前美国钢结构协会（AISC）的荷载抗力系数规范把这种分开来处理的。在目前的实际应用中，结构体系和它构件的相互影响反映在有效长度这一因素上。这一点在社会科学研究技术备忘录第五录摘录中有描述。 尽管结构最大内力和构件最大内力是相互依存的（但不一定共存），应当承认，严格考虑这种相互依存关系，很多结构是不实际的。与此同时，众所周知当遇到复杂框架设计中试图在柱设计时自动弥补整个结构的不稳定（例如通过调整柱的有效长度）是很困难的。因此，社会科学研究委员会建议在实际设计中，这两方面应单独考虑单独构件的稳定性和结构的基础及结构整体稳定性。图28.1就是这种方法的间接分析和设计方法。

在目前的美国钢结构协会荷载抗力系数规范中，分析结构体系的方法是一阶弹性分析或二阶弹性分析。在使用一阶弹性分析时，考虑到二阶效果，一阶力矩都是由B1,B2系数放大。在规范中，所有细部都是从结构体系中独立出来，他们通过细部内力曲线和规范给出的那些隐含二阶效应，非弹性，残余应力和挠度的相互作用设计的。理论解答和实验性数据的拟合曲线得到了柱曲线和梁曲线，同时Kanchanalai发现的所谓“精确”塑性区解决方案的拟合曲线确定了梁柱相互作用方程。 为了证明单个细部内力对整个结构体系的影响，使用了有效长度系数，如图28.2所示。有效长度方法为框架结构提供了一个良好的设计。然而，有效长度方法的

本科毕业设计桥梁外文翻译

附录一：中文翻译 土木工程师 桥梁工程156 2003年3月发表于BEI 31~37页 2002年1月31日收到 C.詹姆斯 2002年12月9日通过高级土木工程师佩尔 Frischmann ，埃克塞特 关键词：桥梁；河堤；土工布；膜与土工格栅 英国锁城大桥 锁城大桥是横跨住宅发展区的铁路桥梁。由于工程施工受到周围建筑与地形的限制，该工程采取加固桥台、桥墩与桥面的刚构结构，以及预制栏杆等方法提高了大桥的使用安全程度，并降低了大桥建造与维护的费用。因此，城堡大桥科学的设计方案使工程成本降到最低。 一、引言 本文描述的是在受限制地区用最小的费用修建一座铁路桥梁使之成为开放的住宅发展区。锁城地区是位于住宅发展十分紧张的韦斯顿超 图1 锁城大桥位置远景

马雷的东部。监督桥梁建设的客户是城堡建设有限公司，它由二大房建者组成。该区的规划局是北盛捷区议会（NSDC）。该发展地区被分为布里斯托尔和埃克塞特。规划条件规定，直到建成这条横跨的铁路大桥为止，该地区南部区域不可能适应居住。可见锁城大桥的建成对该地区发展的重要性。 发展地区位于萨默塞特的边缘，这个地区地形十分的恶劣，该范围位于韦斯顿以北和A321飞机双程双线分隔线的南面。现在只有一条乡下公路，是南部区域的唯一通道。该地区是交通预期不适合住宅增加的区域。 由于盛捷地区水平高程的限制，新的铁路线在桥台两边必须设有高程差。并且该地区地形限制，允许正常横跨的区域较小，这导致在结构的布局上的一定数量的妥协。为了整个城堡地区的发展，全 图2 锁城大桥地图上位置 桥限速20公里/时，并考虑区域范围内的速度制约。这样在得到客户和NSDC的同意后，桥梁采取了最小半径的方法，这使得桥梁采用了比正常梯度更加陡峭地方法实现高程的跨越。 客户的工程师、工程顾问、一般设计原则和初步认同原则下(AIP)与NSDC发出投标文件。 该合同在2000年7月1授予安迪。投标价值1.31亿美元，合同期定为34周，到2001年4月完成。

本科毕业设计方案外文翻译范本

I / 11 本科毕业设计外文翻译 <2018届） 论文题目基于WEB 的J2EE 的信息系统的方法研究 作者姓名[单击此处输入姓名] 指导教师[单击此处输入姓名] 学科(专业 > 所在学院计算机科学与技术学院 提交日期[时间 ]

基于WEB的J2EE的信息系统的方法研究 摘要：本文介绍基于工程的Java开发框架背后的概念，并介绍它如何用于IT 工程开发。因为有许多相同设计和开发工作在不同的方式下重复，而且并不总是符合最佳实践，所以许多开发框架建立了。我们已经定义了共同关注的问题和应用模式，代表有效解决办法的工具。开发框架提供：<1）从用户界面到数据集成的应用程序开发堆栈；<2）一个架构，基本环境及他们的相关技术，这些技术用来使用其他一些框架。架构定义了一个开发方法，其目的是协助客户开发工程。 关键词：J2EE 框架WEB开发 一、引言 软件工具包用来进行复杂的空间动态系统的非线性分析越来越多地使用基于Web的网络平台，以实现他们的用户界面，科学分析，分布仿真结果和科学家之间的信息交流。对于许多应用系统基于Web访问的非线性分析模拟软件成为一个重要组成部分。网络硬件和软件方面的密集技术变革[1]提供了比过去更多的自由选择机会[2]。因此，WEB平台的合理选择和发展对整个地区的非线性分析及其众多的应用程序具有越来越重要的意义。现阶段的WEB发展的特点是出现了大量的开源框架。框架将Web开发提到一个更高的水平，使基本功能的重复使用成为可能和从而提高了开发的生产力。 在某些情况下，开源框架没有提供常见问题的一个解决方案。出于这个原因，开发在开源框架的基础上建立自己的工程发展框架。本文旨在描述是一个基于Java的框架，该框架利用了开源框架并有助于开发基于Web的应用。通过分析现有的开源框架，本文提出了新的架构，基本环境及他们用来提高和利用其他一些框架的相关技术。架构定义了自己开发方法，其目的是协助客户开发和事例工程。 应用程序设计应该关注在工程中的重复利用。即使有独特的功能要求，也

毕业设计外文翻译

毕业设计（论文） 外文翻译 题目西安市水源工程中的 水电站设计 专业水利水电工程 班级 学生 指导教师 2016年

研究钢弧形闸门的动态稳定性 牛志国 河海大学水利水电工程学院，中国南京，邮编210098 nzg_197901@https://www.sodocs.net/doc/be14482240.html,，niuzhiguo@https://www.sodocs.net/doc/be14482240.html, 李同春 河海大学水利水电工程学院，中国南京，邮编210098 ltchhu@https://www.sodocs.net/doc/be14482240.html, 摘要 由于钢弧形闸门的结构特征和弹力，调查对参数共振的弧形闸门的臂一直是研究领域的热点话题弧形弧形闸门的动力稳定性。在这个论文中，简化空间框架作为分析模型，根据弹性体薄壁结构的扰动方程和梁单元模型和薄壁结构的梁单元模型，动态不稳定区域的弧形闸门可以通过有限元的方法，应用有限元的方法计算动态不稳定性的主要区域的弧形弧形闸门工作。此外，结合物理和数值模型，对识别新方法的参数共振钢弧形闸门提出了调查，本文不仅是重要的改进弧形闸门的参数振动的计算方法，但也为进一步研究弧形弧形闸门结构的动态稳定性打下了坚实的基础。 简介 低举升力，没有门槽，好流型，和操作方便等优点，使钢弧形闸门已经广泛应用于水工建筑物。弧形闸门的结构特点是液压完全作用于弧形闸门，通过门叶和主大梁，所以弧形闸门臂是主要的组件确保弧形闸门安全操作。如果周期性轴向载荷作用于手臂，手臂的不稳定是在一定条件下可能发生。调查指出:在弧形闸门的20次事故中，除了极特殊的破坏情况下，弧形闸门的破坏的原因是弧形闸门臂的不稳定;此外，明显的动态作用下发生破坏。例如:张山闸，位于中国的江苏省，包括36个弧形闸门。当一个弧形闸门打开放水时，门被破坏了，而其他弧形闸门则关闭，受到静态静水压力仍然是一样的，很明显，一个动态的加载是造成的弧形闸门破坏一个主要因素。因此弧形闸门臂的动态不稳定是造成弧形闸门(特别是低水头的弧形闸门)破坏的主要原是毫无疑问。

桥梁专业外文翻译--欧洲桥梁研究

中文1850字 附录 Bridge research in Europe A brief outline is given of the development of the European Union, together with the research platform in Europe. The special case of post-tensioned bridges in the UK is discussed. In order to illustrate the type of European research being undertaken, an example is given from the University of Edinburgh portfolio: relating to the identification of voids in post-tensioned concrete bridges using digital impulse radar. Introduction The challenge in any research arena is to harness the findings of different research groups to identify a coherent mass of data, which enables research and practice to be better focused. A particular challenge exists with respect to Europe where language barriers are inevitably very significant. The European Community was formed in the 1960s based upon a political will within continental Europe to avoid the European civil wars, which developed into World War 2 from 1939 to 1945. The strong political motivation formed the original community of which Britain was not a member. Many of the continental countries saw Britain’s interest as being purely economic. The 1970s saw Britain joining what was then the European Economic Community (EEC) and the 1990s has seen the widening of the community to a European Union, EU, with certain political goals together with the objective of a common European currency. Notwithstanding these financial and political developments, civil engineering and bridge engineering in particular have found great difficulty in forming any kind of common thread. Indeed the educational systems for University training are quite different between Britain and the European continental countries. The formation of the EU funding schemes —e.g. Socrates, Brite Euram and other programs have helped significantly. The Socrates scheme is based upon the exchange of students between Universities in different member states. The Brite Euram scheme has involved technical research grants given to consortia of academics and industrial

本科毕业设计外文翻译

Section 3 Design philosophy, design method and earth pressures 3.1 Design philosophy 3.1.1 General The design of earth retaining structures requires consideration of the interaction between the ground and the structure. It requires the performance of two sets of calculations: 1）a set of equilibrium calculations to determine the overall proportions and the geometry of the structure necessary to achieve equilibrium under the relevant earth pressures and forces; 2）structural design calculations to determine the size and properties of thestructural sections necessary to resist the bending moments and shear forces determined from the equilibrium calculations. Both sets of calculations are carried out for specific design situations (see 3.2.2) in accordance with the principles of limit state design. The selected design situations should be sufficiently Severe and varied so as to encompass all reasonable conditions which can be foreseen during the period of construction and the life of the retaining wall. 3.1.2 Limit state design This code of practice adopts the philosophy of limit state design. This philosophy does not impose upon the designer any special requirements as to the manner in which the safety and stability of the retaining wall may be achieved, whether by overall factors of safety, or partial factors of safety, or by other measures. Limit states (see 1.3.13) are classified into: a) ultimate limit states (see 3.1.3); b) serviceability limit states (see 3.1.4). Typical ultimate limit states are depicted in figure 3. Rupture states which are reached before collapse occurs are, for simplicity, also classified and

桥梁外文翻译

毕业设计/论文 外文文献翻译 院系城市建设学院 专业班级 姓名 原文出处 评分 指导教师 华中科技大学武昌分校 20 12 年3月1日

Study on nonlinear analysis of a redundant cable-stayed bridge 1．Abstract A comparison on nonlinear analysis of a highly redundant cable-stayed bridge is performed in the study. The initial shapes including geometry and prestress distribution of the bridge are determined by using a two-loop iteration method, it is an equilibrium iteration loop and a shape iteration loop. For the initial shape analysis a linear and a nonlinear computation procedure are set up. In the former all nonlinearities of cable-stayed bridges are disregarded, and the shape iteration is carried out without considering equilibrium. In the latter all nonlinearities of the bridges are taken into consideration and both the equilibrium and the shape iteration are carried out. Based on the convergent initial shapes determined by the different procedures, the natural frequencies and vibration modes are then examined in details. Numerical results show that a convergent initial shape can be found rapidly by the two-loop iteration method, a reasonable initial shape can be determined by using the linear computation procedure, and a lot of computation efforts can thus be saved. There are only small differences in geometry and prestress distribution between the results determined by linear and nonlinear computation procedures. However, for the analysis of natural frequency and vibration modes, significant differences in the fundamental frequencies and vibration modes will occur, and the nonlinearities of the cable-stayed bridge response appear only in the modes determined on basis of the initial shape found by the nonlinear computation. 2. Introduction Rapid progress in the analysis and construction of cable-stayed bridges has been made over the last three decades. The progress is mainly due to developments in the fields of computer technology, high strength steel cables, orthotropic steel decks and construction technology. Since the first modern cable-stayed bridge was built in Sweden in 1955, their popularity has rapidly been increasing all over the world. Because of its aesthetic appeal, economic grounds and ease of erection, the

毕业设计外文翻译

毕业设计（论文） 外文文献翻译 题目：A new constructing auxiliary function method for global optimization 学院： 专业名称： 学号： 学生姓名： 指导教师： 2014年2月14日

一个新的辅助函数的构造方法的全局优化 Jiang-She Zhang，Yong-Jun Wang https://www.sodocs.net/doc/be14482240.html,/10.1016/j.mcm.2007.08.007 非线性函数优化问题中具有许多局部极小，在他们的搜索空间中的应用，如工程设计，分子生物学是广泛的，和神经网络训练．虽然现有的传统的方法，如最速下降方法，牛顿法，拟牛顿方法，信赖域方法，共轭梯度法，收敛迅速，可以找到解决方案，为高精度的连续可微函数，这在很大程度上依赖于初始点和最终的全局解的质量很难保证．在全局优化中存在的困难阻碍了许多学科的进一步发展．因此，全局优化通常成为一个具有挑战性的计算任务的研究． 一般来说，设计一个全局优化算法是由两个原因造成的困难：一是如何确定所得到的最小是全球性的（当时全球最小的是事先不知道），和其他的是，如何从中获得一个更好的最小跳．对第一个问题，一个停止规则称为贝叶斯终止条件已被报道．许多最近提出的算法的目标是在处理第二个问题．一般来说，这些方法可以被类?主要分两大类，即：（一）确定的方法，及（ii）的随机方法．随机的方法是基于生物或统计物理学，它跳到当地的最低使用基于概率的方法．这些方法包括遗传算法（GA），模拟退火法（SA）和粒子群优化算法（PSO）．虽然这些方法有其用途，它们往往收敛速度慢和寻找更高精度的解决方案是耗费时间．他们更容易实现和解决组合优化问题．然而，确定性方法如填充函数法，盾构法，等，收敛迅速，具有较高的精度，通常可以找到一个解决方案．这些方法往往依赖于修改目标函数的函数“少”或“低”局部极小，比原来的目标函数，并设计算法来减少该?ED功能逃离局部极小更好的发现． 引用确定性算法中，扩散方程法，有效能量的方法，和积分变换方法近似的原始目标函数的粗结构由一组平滑函数的极小的“少”．这些方法通过修改目标函数的原始目标函数的积分．这样的集成是实现太贵，和辅助功能的最终解决必须追溯到