模具术语 中英文翻译
?assembling mould装配铸型
?baked mould干型
?bar mould多穴压模
?big-end-up mould上大下小钢锭模
?black mould of rice 黑变病
?blank mould turnover 雏型模翻转
?blowing mould吹模
?blue mould of citrus 柑桔青霉病
?cap mould压顶线脚
?car type mould conveyor 小车式铸型输送机?case mould plaster 母模用石膏
?centrifugal casting mould离心铸造铸型?ceramic mould casting 陶瓷模注法
?channel mould槽模
?chill mould冷铸型(模)
?close mould封闭铸型
?close mould(铸造用) 合箱
?closed mould闭式模; 闭式压模
?cold-punching mould冷冲模
?collapsible mould分室模
?composite ceramic mould复合陶瓷型
?composite mould casting 复合型铸造
?copper mould base 铜模底
?copper mould wall 铜坩埚壁
?corrugated mould波形铸模
?cover mould压缝线脚
?covered floor mould盖箱地面铸型
?cylinder mould machine 圆网造纸机
?double-mould-broad ridging plough 双壁起垄犁?draw mould薄壁模子
?driel mould干型
?drip mould滴水线脚
?dry sand mould干型
?ear mould耳模
?electric pole mould hanger 电杆模型吊架?end mould端模
?Erical mould可压锭模; 挤压锭模
?evacuated mould空腔模
?face mould面模
?fall wheat snow mould冬小麦雪霉病
?falling mould曲型线条
?female mould阴模
?fixed mould固定模
?flaskless mould无箱铸型
?floating-point mould浮点模型
?floor mould地铸模
?fluted mould波形模
?foam sponge mould泡沫胶硫化模
?footed mould压印底圈的模型
?forging mould锻模
?front mould前模
?full-mould casting process 实型铸造?gang mould成组模; 成组模板
?garden mould园土
?get in the mould垫平铸型
?glass mould玻璃型; 玻璃铸型
?glass mould diode 玻璃模二极管
?graphite mould石墨型
?grass mould腐草土
?gray mould灰霉
?green mould绿霉病
?green mould of citrus 柑桔绿霉病
?ground mould地面铸型; 堆土木模
?gypsum mould石膏型
?hair mould毛霉
?hair mould sprout 毛霉芽
?half mould半型
?hoist for mould board carrier 模板车升降机?hump mould压坯用阳模
?ice mould冰铸
?ingot mould钢锭模; 铸锭模; 铸锭型; 锭模?ingot mould milling machine 钢锭模铣床?ingot slab mould扁钢锭模
?insulating mould coating 隔热涂料
?integral mould整模型
?invested mould熔模铸型
?iron mould铁锈迹
?leaf mould叶霉; 腐叶土
?loam mould泥型
?lower mould half 下模; 凹模
?male mould凸模; 阳模
?master mould母型; 原模
?mismatch in mould铸型错箱
?mould印模; 模; 模板; 模具; 模筛样板; 模塑; 模子; 成型模具; 圆网; 造型模板; 塑模; 霉; 霉病; 霉菌; 纸型
?mould addition 钢锭模添加剂
?mould and die milling machine 模具铣床
?mould assembling 合箱
?mould assembling and closing 铸型合箱
?mould assembly 合型
?mould blower 吹型机
?mould board 造型板; 样板
?mould boardless plough 无壁犁
?mould buggy 钢锭模车
?mould case 模制壳
?mould clamp 卡具
?mould clamps 模型紧固夹
?mould cleaner 模具清洁剂
?mould closer 合箱机; 合箱装置
?mould coating material 钢锭模涂料
?mould core 模芯
?mould cover 腐殖质层
?mould cure 模塑硫化; 模型硫化
?mould dam aged sweet potato poisoning 黑斑甘薯中毒?mould dimension 铸型尺寸
?mould drag 下半箱
?mould drying 铸型烘干
?mould efficiency 模塑效率
?mould emptier 脱模机构
?mould erosion 铸型冲蚀
?mould facing 涂料
?mould fitter 合箱工
?mould flat gauge 样板
?mould form 模型型腔
?mould fungus 霉菌
?mould growth test 长霉试验
?mould half 半型
?mould hardness 铸型硬度
?mould impression 模型内腔; 模型型腔; 模穴
?mould in a snap flask 无箱造型?mould in the pit 地坑造型
?mould inoculation 型内孕育
?mould jacket 型套
?mould kernel 模芯
?mould life 模型寿命
?mould lifting 铸型起模
?mould lining 坩埚衬里
?mould loft 放样间
?mould loft floor 放样台
?mould lofter 放样工; 放样工人?mould loftsman 放样工; 放样工人
?mould machine 模塑机
?mould machine of cereal seed selection 谷物选种机?mould mark 模缝条痕
?mould matrix cathode 模制阴极
?mould oil 脱模油
?mould on end 垂直分型造型
?mould pig iron 型铁
?mould plaster 模型用石膏
?mould plate 模型板
?mould plunger 阳模
?mould plunger force plug 凸模
?mould preparation bay 钢锭模准备跨
?mould press 模压机
?mould pressing 旋压成形
?mould proofing 防霉
?mould rains 梅雨
?mould release 分型粉
?mould relese 脱模
?mould rollover unit 翻箱装置
?mould sand 型砂
?mould seam 模缝
?mould setting-and-stripping bay 钢锭模准备和脱锭跨?mould shift 错箱
?mould shrinkage 模内收缩; 模压收缩; 脱模后的收缩
?mould splits 模组分
?mould stripping 铸型起模; 拆模?mould susceptibility 感霉性
?mould test chamber 霉菌试验箱
?mould train 模组
?mould turnover 翻箱
?mould unloading 出模; 脱模; 卸模?mould veining 铸型裂纹
?mould vibrator 模板振动器
?mould vulcanization 模塑硫化
?mould wash 脱模涂料
?mould wash mixer 涂料搅拌机
?multiple cavity mould多型腔铸型; 多巢模
?multiple mould多件石膏模
?multiple-part mould多箱铸型
?needle mould针模
?one-piece mould整体铸型
?open bottom mould底开式钢锭模
?open mould明浇铸型; 敞口铸型
?open sand mould明浇砂型
?optical instrument mould and fog auto-detector 光学仪器霉雾自动检测仪
?ornamental mould艺术造型
?pallet conveyer mould machine 滑板输送式造型机
?paper mould纸型
?paste mould衬碳模
?paste mould ware 衬碳模成形的制品?peat mould泥炭土
?permanent mould永久铸型
?pig mould锭模
?plural mould operation 多模操作?porous mould多孔模型
?positive mould阳模; 阳压模
?press mould压模
?press mould ware 模压器皿
?pressing mould压模
?process of unconventional heat treatment of mould模具非常规热处理工艺
?quadrant mould四开木压条
?real mould实模型
?rectal suppository mould肛门栓剂模
?refractory shell mould耐火材料壳型
?removal of the mould拆模
?reverse mould倒模; 倒型
?revesing permanent mould双面金属型
?ring mould瓶颈模
?ring-shaped mould环型铸模
?risk of mould发霉险
?roast sand mould干砂型
?rubber mould橡胶皮模
?running mould模筛样板; 模饰样板
?saccharifying mould糖化霉
?sealing of a mould铸型密封
?section mould型模
?sectional mould镶合砂型
?semi-automatic mould半自动模; 半自动塑模
?semi-chilled mould casting 半金属型铸造; 半冷模铸造?semi-permanent mould半永久型; 半永久性模
?semiclosed top mould半封顶锭模
?shell mould machine 壳型造型机
?shiftable mould-board 可拆换的刀片
?sign mould符号模型
?single cavity mould整体铸型
?single mould单件模型
?skin dried mould面干铸型
?skin drying mould表干型
?sleeper steel mould轨枕钢模
?slime mould粘菌
?slip flask mould脱箱铸型
?snap flask mould活箱造型; 无箱铸型?snapflask mould脱箱造型
?snow mould雪霉病; 雪疫病
?soap mould皂模
?sooty mould烟霉; 煤污病
?sooty mould of rice plant 水稻煤病
?sooty mould of tea 茶叶煤污病
?spacing mould隔膜
?split mould对开模
?stagnant mould不动模型
?standard steel ingot mould标准钢锭模?steel mould钢锭模; 钢模
?steel mould for electric pole 电杆钢模?stock mould定型模
?stripper-plate mould脱模板塑模
?sweeping loam mould刮泥型
塑胶模具类中英文对照专业术语
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉，象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
冲压模具专业词汇中英文翻译
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug
模具术语(中英文对照)
AD-Diameter The tread diameter at the centerline of the tread (EU); also: "T-Diameter"(GT) AD直径：指胎面中心线直径（EU）。又叫T直径（GT） Auto-lock Ear A Lug on the cone ring used to mount the mold/container in the top half of a 60“ NRM Auto-lock press. 导环上的突缘，用于和60“ NRM Auto-lock 硫化机上半部连接。 Bead Ring The tire bead forming ring (also: toe ring) 钢圈，也称toe ring Bead Ring Register The landing and tapered seat that the bead ring fits into 钢圈配合：侧板上，和钢圈配合的平面及锥面 Bottom Container Plate The plate that the bottom sidewall plate is bolted to 模壳底座 Bottom Container Plate Lifting Lug A lug attached to the Bottom Container Plate with Horizontal holes used for lifting. 模壳底座吊耳：装配在底座上、有水平的孔，用来吊装的吊耳 Bottom Container Plate Dowel Pin Lug A lug attached to the Bottom Container Plate that supports the Dowel Pin Bushing. 装配在底座上，用来支承定位销套的突缘 Bottom Container Plate Hold Down A lug that is used to fix the Bottom Plate in the Press. 用来将底座装配在硫化机上的突缘 Breaker Hook A hook fixed to the bottom of the tread segment that catches the bottom container plate only when the segment will not release from the tire during de-molding. 分离钩：固定在花纹块底部的钩子，轮胎硫化完后若花纹块不能跟轮胎分离，就用此钩抓住模壳底座帮助花纹块和轮胎进行分离。
塑料注塑模具中英文对照外文翻译文献
外文翻译及原文 (文档含英文原文和中文翻译) 【原文一】 CONCURRENT DESIGN OF PLASTICS INJECTION MOULDS Abstract The plastic product manufacturing industry has been growing rapidly in recent years. One of the most popular processes for making plastic parts is injection moulding. The design of injection mould is critically important to product quality and efficient product processing. Mould-making companies, who wish to maintain the competitive edge, desire to shorten both design and manufacturing leading times of the by applying a systematic mould design process. The mould industry is an important support industry during the product development process, serving as an important link between the product designer and manufacturer. Product development has changed from the traditional serial process of design, followed by manufacture, to a more organized concurrent process where design and manufacture are considered at a very early stage of design. The concept of concurrent engineering (CE) is no longer new and yet it is still applicable and relevant in today’s manuf acturing environment. Team working spirit, management involvement, total design process and integration of IT tools are still the essence of CE. The application of The CE process to the design of an injection process involves the simultaneous consideration of plastic part design, mould design and injection moulding machine selection, production scheduling and cost as early as possible in the design stage.
模具术语英文翻译知识讲解
模具术语英文翻译
模具术语英文翻译 根据国家标准，以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准，以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
模具术语翻译
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainer plate 托板：support plate
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
大底模具技术术语中英文对照
LN3--PU/Phylon/Rubber Process Contents for these three sections of English Version PFC: ?Phylon Work Sheet PH数据表 ?Components Specification Sheet(Phylon) 部件明细单(Phylon)?Component Specification Sheet Set Up(Phylon) (此部分无中文) ?Phylon Midsole Specifications PH全插规格 ?Phylon Preform Specifications PH粗胚规格 ?Preform Drawing 粗胚图 ?Component Specification Sheet Set Up(PU) (此部分无中文) ?PU Midsole Specifications PU全插规格 ?PU Midsole Specifications II PU数据表 ?Components Specification Sheet(PU) 部件明细单(PU) ?PU Midsole Pouring Specification PU灌注明细 ?Outsole Color Schedule 本底颜色明细 ?Outsole Preform Specifications 本底粗胚规格 ?Outsole Pressing Process 本底压制流程 ?Outsole Degreasing Process 本底水洗流程 ********************************************************************* ΦPU Section ΦPU部分 ********************************************************************* air bag schedule 空气袋分段 specific instructions 特别说明 air bag diagram 空气袋图示 hardness(skin on) 硬度（带皮） density 密度 elongation 延伸率 tear 撕力 tensile 拉力 split tear 撕裂 painting 喷漆 MCS number 材料编号 mold release agent 脱模剂 polyurethane 聚安脂 polyester 聚脂 Density must be within NIKE spec and follow weight chart 密度必须符合NIKE要求及重量表 No dirty midsole sidewalls yellowing or poor cosmetics due to mold condition. 无因模具造成的边墙黄变及外观不良。 Correct molded or painted colors per NIKE confirmation. 根据NIKE的确认，成型材料及喷漆颜色正确。 Correct top/bottom edge trimming within 1mm width allowance. 正确修边上部及底部边缘，允许1mm余量。 No larger than 5mm diameter internal air voids.(checked by light table)
各式模具分类用语中英文对照
Landed plunger mold有肩柱塞式模具Burnishing die 挤光模 Landed positive mold 有肩全压式模具Button die镶入式圆形凹模 Loading shoe mold料套式模具Center-gated mold中心浇口式模具Loose detail mold 活零件模具 Chill mold 冷硬铸模 Loose mold 活动式模具 Cold hobbing冷挤压制模 Louvering die百叶窗冲切模Composite dies 复合模具 Manifold die分歧管模具 Counter punch反凸模 Modular mold 组合式模具 Double stack mold 双层模具 Multi-cavity mold多模穴模具Electroformed mold电铸成形模 Multi-gate mold复式浇口模具Expander die 扩径模 Offswt bending die双折冷弯模具Extrusion die 挤出模 Palletizing die 叠层模 Family mold反套制品模具 Plaster mold 石膏模 Blank through dies漏件式落料模Porous mold 通气性模具Duplicated cavity plate复板模Positive mold全压式模具 Fantail die扇尾形模具 Pressure die压紧模 Fishtail die鱼尾形模具 Profile die轮廓模 Flash mold 溢料式模具Progressive die顺序模 Gypsum mold 石膏铸模 Protable mold 手提式磨具 Hot-runner mold热流道模具Prototype mold 雏形试验模具 Ingot mold钢锭模 Punching die 落料模 Lancing die 切口模 Raising (embossing) 压花起伏成形Re-entrant mold 倒角式模具
模具英语翻译大全
1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動） 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.（加肉面積太大） 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角，填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄，強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面，不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚，會有縮水，建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. （此面是不是外觀面，此處做滑塊的話會有結合線，是否可以接受） 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. （此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷） 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. （請盡快確認這種拆模方式和結構，否則會影響模期） 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. （GATE做在此處的話.蓋子打開後看不到GATE的修剪部位） 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角，以便脫模順利） 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. （P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響） 29. If you insist that the gate position have to be as original design then we would
冲压模具专业词汇中英文翻译
冲压模具词汇Counter bored hole沉孔 Chamfer倒斜角 Fillet倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count复盘人 second check复盘复核人
equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count复盘点数量 Quantity of customs count会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills年终盘点截止单据汇总表 bill name单据名称 Thissheetandphysicalinventorylistwillbesenttoaccountingdepartmenttogether(T hoseofNHKwillbesenttofinancialdepartment) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card年终盘点卡与清册使用－状况明细表blank and waste sheet NO.空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品
五金模具常用专业术语中英文对照表
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die
模具术语翻译
模具名词中英文对照表 序号中文名英文名 1 一、水口gate 2 进水位gate location 3 水口形式gate type 4 大水口edge gate 5 细水口pin-point gate 6 水口大小gate size 7 转水口switching gate 8 唧嘴口径sprue diameter 9 二、流道runner 10 热流道hot runner 11 冷流道cold runner 12 唧嘴直流direct sprue gate 13 圆形流道round runner 14 模流分析mold flow analysis 15 流道平衡runner balance 16 热嘴hot sprue 17 热流道板hot manifold 18 发热管cartridge heater 19 探针thermocouples 20 插头connector plug 21 插座connector socket 22 密封/封料seal 23 三、运水water line 24 喉塞line pug 25 喉管tube 26 塑胶管plastic tube 27 快速接头jiffy quick connector plug 28 四、模具零件mold components 29 三板模three-plate mold
模具名词中英文对照表 序号中文名英文名 30 二板模two-plate mold 31 边钉/导边leader pin/guide pin 32 边司/导套bushing/guide bushing 33 顶针板ejector retainer plate 34 托板support plate 35 螺丝screw 36 管钉dowel pin 37 开模槽ply bar score 38 内模管位core/cavity inter-lock 39 顶针ejector pin 40 司筒ejector sleeve 41 司筒针ejector pin 42 推板stripper plate 43 缩呵movable core 44 扣机（尼龙拉勾）nylon latch lock 45 斜顶lifter 46 模胚（架）mold base 47 母模cavity insert 48 公模core insert 49 行位（滑块）slide 50 镶件insert 51 压座/斜鸡wedge 52 耐磨板/油板wedge wear plate 53 压条plate 54 撑头support pillar 55 唧嘴sprue bushing 56 挡板stop plate 57 定位圈locating ring 58 锁扣latch 模具名词中英文对照表 序号中文名英文名