土木工程专业---外文文献翻译

外文文献翻译

土木工程系

系别：_________________________ 班级：_________________________ 姓名：_________________________ 指导教师：_________________________

1 中文翻译

1.1钢筋混凝土

素混凝土是由水泥、水、细骨料、粗骨料（碎石或；卵石）、空气，通常还有其他外加剂等经过凝固硬化而成。将可塑的混凝土拌合物注入到模板内，并将其捣实，然后进行养护，以加速水泥与水的水化反应，最后获得硬化的混凝土。其最终制成品具有较高的抗压强度和较低的抗拉强度。其抗拉强度约为抗压强度的十分之一。因此，截面的受拉区必须配置抗拉钢筋和抗剪钢筋以增加钢筋混凝土构件中较弱的受拉区的强度。

由于钢筋混凝土截面在均质性上与标准的木材或钢的截面存在着差异，因此，需要对结构设计的基本原理进行修改。将钢筋混凝土这种非均质截面的两种组成部分按一定比例适当布置，可以最好的利用这两种材料。这一要求是可以达到的。因混凝土由配料搅拌成湿拌合物，经过振捣并凝固硬化，可以做成任何一种需要的形状。如果拌制混凝土的各种材料配合比恰当，则混凝土制成品的强度较高，经久耐用，配置钢筋后，可以作为任何结构体系的主要构件。

浇筑混凝土所需要的技术取决于即将浇筑的构件类型，诸如：柱、梁、墙、板、基础，大体积混凝土水坝或者继续延长已浇筑完毕并且已经凝固的混凝土等。对于梁、柱、墙等构件，当模板清理干净后应该在其上涂油，钢筋表面的锈及其他有害物质也应该被清除干净。浇筑基础前，应将坑底土夯实并用水浸湿6英寸，以免土壤从新浇的混凝土中吸收水分。一般情况下，除使用混凝土泵浇筑外，混凝土都应在水平方向分层浇筑，并使用插入式或表面式高频电动振捣器捣实。必须记住，过分的振捣将导致骨料离析和混凝土泌浆等现象，因而是有害的。

水泥的水化作用发生在有水分存在，而且气温在50°F以上的条件下。为了保证水泥的水化作用得以进行，必须具备上述条件。如果干燥过快则会出现表面裂缝，这将有损与混凝土的强度，同时也会影响到水泥水化作用的充分进行。

设计钢筋混凝土构件时显然需要处理大量的参数，诸如宽度、高度等几何尺寸，配筋的面积，钢筋的应变和混凝土的应变，钢筋的应力等等。因此，在选择混凝土截面时需要进行试算并作调整，根据施工现场条件、混凝土原材料的供应情况、业主提出的特殊要求、对建筑和净空高度的要求、所用的设计规范以及建筑物周围环境条件等最后确定截面。钢筋混凝土通常是现场浇注的合成材料，它与在工厂中制造的标准的钢结构梁、柱等不同，因此对于上面所提到的一系列因素必须予以考虑。

对结构体系的各个部位均需选定试算截面并进行验算，以确定该截面的名义强度是否足以承受所作用的计算荷载。由于经常需要进行多次试算，才能求出所需的

截面，因此设计时第一次采用的数值将导致一系列的试算与调整工作。

选择混凝土截面时，采用试算与调整过程可以使复核与设计结合在一起。因此，当试算截面选定后，每次设计都是对截面进行复核。手册、图表和微型计算机以及专用程序的使用，使这种设计方法更为简捷有效，而传统的方法则是把钢筋混凝土的复核与单纯的设计分别进行处理。

1.2土方工程

由于和土木工程中任何其他工种的施工方法与费用相比较，土方挖运的施工方法与费用的变化都要快得多，因此对于有事业心的人来说，土方工程是一个可以大有作为的领域。在1935年，目前采用的利用轮胎式机械设备进行土方挖运的方法大多数还没有出现。那是大部分土方是采用窄轨铁路运输，在这目前来说是很少采用的。当时主要的开挖方式是使用正铲、反铲、拉铲或抓斗等挖土机，尽管这些机械目前仍然在广泛应用，但是它们只不过是目前所采用的许多方法中的一小部分。因此，一个工程师为了使自己在土方挖运设备方面的知识跟得上时代的发展，他应当花费一些时间去研究现代的机械。一般说来，有关挖土机、装载机和运输机械的唯一可靠而又最新的资料可以从制造厂商处获得。

土方工程或土方挖运工程指的是把地表面过高处的土壤挖去（挖方），并把它倾卸到地表面过低的其他地方（填方）。为了降低土方工程费用，填方量应该等于挖方量，而且挖方地点应该尽可能靠近土方量相等的填方地点，以减少运输量和填方的二次搬运。土方设计这项工作落到了从事道路设计的工程师的身上，因为土方工程的设计比其他任何工作更能决定工程造价是否低廉。根据现有的地图和标高，道路工程师应在设计绘图室中的工作也并不是徒劳的。它将帮助他在最短的时间内获得最好的方案。

费用最低的运土方法是用同一台机械直接挖方取土并且卸土作为填方。这并不是经常可以做到的，但是如果能够做到则是很理想的，因为这样做既快捷又省钱。拉铲挖土机。推土机和正铲挖土机都能做到这点。拉铲挖土机的工作半径最大。推土机所推运的图的数量最多，只是运输距离很短。拉铲挖土机的缺点是只能挖比它本身低的土，不能施加压力挖入压实的土壤内，不能在陡坡上挖土，而且挖。卸都不准确。

正铲挖土机介于推土机和拉铲挖土机的之间，其作用半径大于推土机，但小于拉铲挖土机。正铲挖土机能挖取竖直陡峭的工作面，这种方式对推土机司机来说是危险的，而对拉铲挖土机则是不可能的。每种机械设备应该进行最适合它的性能的作业。正铲挖土机不能挖比其停机平面低很多的土，而深挖坚实的土壤时，反铲挖土机最适用，但其卸料半径比起装有正铲的同一挖土机的卸料半径则要小很多。

在比较平坦的场地开挖，如果用拉铲或正铲挖土机运输距离太远时，则装有轮胎式的斗式铲运机就是比不可少的。它能在比较平的地面上挖较深的土（但只能挖机械本身下面的土），需要时可以将土运至几百米远，然后卸土并在卸土的过程中把土大致铲平。在挖掘硬土时，人们发现在开挖场地经常用一辆助推拖拉机（轮式或履带式），对返回挖土的铲运机进行助推这种施工方法是经济的。一旦铲运机装满，助推拖拉机就回到开挖的地点去帮助下一台铲运机。

斗式铲运机通常是功率非常大的机械，许多厂家制造的铲运机铲斗容量为8 m 3，满载时可达10 m3。最大的自行式铲运机铲斗容量为19立方米（满载时为25 m 3），由430马力的牵引发动机驱动。

翻斗机可能是使用最为普遍的轮胎式运输设备，因为它们还可以被用来送混凝土或者其他建筑材料。翻斗车的车斗位于大橡胶轮胎车轮前轴的上方，尽管铰接式翻斗车的卸料方向有很多种，但大多数车斗是向前翻转的。最小的翻斗车的容量大约为0.5立方米，而最大的标准型翻斗车的容量大约为4.5m3。特殊型式的翻斗车包括容量为4 m3的自装式翻斗车，和容量约为0.5 m3的铰接式翻斗车。必须记住翻斗车与自卸卡车之间的区别。翻斗车车斗向前倾翻而司机坐在后方卸载，因此有时被称为后卸卡车。

1.3结构的安全度

规范的主要目的是提供一般性的设计原理和计算方法，以便验算结构的安全度。就目前的趋势而言，安全系数与所使用的材料性质及其组织情况无关，通常把它定义为发生破坏的条件与结构可预料的最不利的工作条件之比值。这个比值还与结构的破坏概率（危险率）成反比。

破坏不仅仅指结构的整体破坏，而且还指结构不能正常的使用，或者，用更为确切的话来说，把破坏看成是结构已经达到不能继续承担其设计荷载的“极限状态”。通常有两种类型的极限状态，即：

（1）强度极限状态，它相当于结构能够达到的最大承载能力。其例子包括结构的局部屈曲和整体不稳定性；某此界面失效，随后结构转变为机构；疲劳破坏；引起结构几何形状显著变化的弹性变形或塑性变形或徐变；结构对交变荷载、火灾和爆炸的敏感性。

（2）使用极限状态，它对应着结构的使用功能和耐久性。器例子包括结构失稳之前的过大变形和位移；早期开裂或过大的裂缝；较大的振动和腐蚀。

根据不同的安全度条件，可以把结构验算所采用的计算方法分成：

（1）确定性的方法，在这种方法中，把主要参数看作非随机参数。

（2）概率方法，在这种方法中，主要参数被认为是随机参数。

此外，根据安全系数的不同用途，可以把结构的计算方法分为：

（1）容许应力法，在这种方法中，把结构承受最大荷载时计算得到的应力与经过按规定的安全系数进行折减后的材料强度作比较。

（2）极限状态法，在这种方法中，结构的工作状态是以其最大强度为依据来衡量的。由理论分析确定的这一最大强度应不小于结构承受计算荷载所算得的强度（极限状态）。计算荷载等于分别乘以荷载系数的活载与恒载之和。

把对应于不乘以荷载系数的活载和恒载的工作（使用）条件的应力与规定值（使用极限状态）相比较。根据前两种方法和后两种方法的四种可能组合，我们可以得到一些实用的计算方法。通常采用下面两种计算方法：

确定性的方法，这种方法采用容许应力。

概率方法，这种方法采用极限状态。

至少在理论上，概率法的主要优点是可以科学的考虑所有随机安全系数，然后将这些随机安全系数组合成确定的安全系数。概率法取决于：

（1）制作和安装过程中材料强度的随机分布（整个结构的力学性能数值的分散性）；

（2）截面和结构几何尺寸的不确定性（由结构制作和安装造成的误差和缺陷而引起的）；

对作用在结构上的活载和恒载的预测的不确定性；

所采用的近似计算方法有关的不精确性（实际应力与计算应力的偏差）。

此外，概率理论意味着可以基于下面几个因素来确定允许的危险率，例如：建筑物的重要性和建筑物破坏造成的危害性；

（2）由于建筑物破坏使生活受到威胁的人数；

（3）修复建筑的可能性；

（4）建筑物的预期寿命。

所有这些因素均与经济和社会条件有关，例如：

（1）建筑物的初始建设费；

（2）建筑物使用期限内的折旧费；

（3）由于建筑物破坏而造成的物质和材料损失费；

（4）在社会上造成的不良影响；

（5）精神和心理上的考虑。

就给定的安全系数而论，所有这些参数的确定都是以建筑物的最佳成本为依据的。但是，应该考虑到进行全概率分析的困难。对于这种分析来说，应该了解活载及其所引起的盈利的分布规律、材料的力学性能的分散性和截面的结构几何尺寸的分散性。此外，由于强度的分布规律和应力的分布规律之间的相互关系是困难的。

这些实际困难可以采用两种方法来克服。第一种方法对材料和荷载采用不同的安全系数，而不需要采用概率准则；第二种方法是引入一些而简化假设的近似概率方法（半概率方法）。

2 外文翻译

2.1 Reinforced Concrete

Plain concrete is formed from a hardened mixture of cement ,water ,fine aggregate, coarse aggregate (crushed stone or gravel),air, and often other admixtures. The plastic mix is placed and consolidated in the formwork, then cured to facilitate the acceleration of the chemical hydration reaction lf the cement/water mix, resulting in hardened concrete. The finished product has high compressive strength, and low resistance to tension, such that its tensile strength is approximately one tenth lf its compressive strength. Consequently, tensile and shear reinforcement in the tensile regions of sections has to be provided to compensate for the weak tension regions in the reinforced concrete element.

It is this deviation in the composition of a reinforces concrete section from the homogeneity of standard wood or steel sections that requires a modified approach to the basic principles of structural design. The two components of the heterogeneous reinforced concrete section are to be so arranged and proportioned that optimal use is made of the materials involved. This is possible because concrete can easily be given any desired shape by placing and compacting the wet mixture of the constituent ingredients are properly proportioned, the finished product becomes strong, durable, and, in combination with the reinforcing bars, adaptable for use as main members of any structural system.

The techniques necessary for placing concrete depend on the type of member to be cast: that is, whether it is a column, a bean, a wall, a slab, a foundation. a mass columns, or an extension of previously placed and hardened concrete. For beams, columns, and walls, the forms should be well oiled after cleaning them, and the reinforcement should be cleared of rust and other harmful materials. In foundations, the earth should be compacted and thoroughly moistened to about 6 in. in depth to avoid absorption of the moisture present in the wet concrete. Concrete should always be placed in horizontal layers which are compacted by means of high frequency power-driven vibrators of either the immersion or external type, as the case requires, unless it is placed by pumping. It must be kept in mind, however, that over vibration can be harmful since it could cause segregation of the aggregate and bleeding of the concrete.

Hydration of the cement takes place in the presence of moisture at temperatures above 50°F. It is necessary to maintain such a condition in order that the chemical hydration reaction can take place. If drying is too rapid, surface cracking takes place. This would result in reduction of concrete strength due to cracking as well as the failure to attain full chemical hydration.

It is clear that a large number of parameters have to be dealt with in proportioning a reinforced concrete element, such as geometrical width, depth, area of reinforcement, steel strain, concrete strain, steel stress, and so on. Consequently, trial and adjustment is necessary in the choice of concrete sections, with assumptions based on conditions at site, availability of the constituent materials, particular demands of the owners, architectural and headroom requirements, the applicable codes, and environmental reinforced concrete is often a site-constructed composite, in contrast to the standard mill-fabricated beam and column sections in steel structures.

A trial section has to be chosen for each critical location in a structural system. The trial section has to be analyzed to determine if its nominal resisting strength is adequate to carry the applied factored load. Since more than one trial is often necessary to arrive at the required section, the first design input step generates into a series of trial-and-adjustment analyses.

The trial-and –adjustment procedures for the choice of a concrete section lead to the convergence of analysis and design. Hence every design is an analysis once a trial section is chosen. The availability of handbooks, charts, and personal computers and programs supports this approach as a more efficient, compact, and speedy instructional method compared with the traditional approach of treating the analysis of reinforced concrete separately from pure design.

2.2 Earthwork

Because earthmoving methods and costs change more quickly than those in any other branch of civil engineering, this is a field where there are real opportunities for the enthusiast. In 1935 most of the methods now in use for carrying and excavating earth with rubber-tyred equipment did not exist. Most earth was moved by narrow rail track, now relatively rare, and the main methods of excavation, with face shovel, backacter, or dragline or grab, though they are still widely used are only a few of the many current methods. To keep his knowledge of earthmoving equipment up to date an engineer must therefore spend tine studying modern machines. Generally the only reliable up-to-date

information on excavators, loaders and transport is obtainable from the makers.

Earthworks or earthmoving means cutting into ground where its surface is too high ( cuts ), and dumping the earth in other places where the surface is too low ( fills). Toreduce earthwork costs, the volume of the fills should be equal to the volume of the cuts and wherever possible the cuts should be placednear to fills of equal volume so as to reduce transport and double handlingof the fill. This work of earthwork design falls on the engineer who lays out the road since it is the layout of the earthwork more than anything else which decides its cheapness. From the available maps ahd levels, the engineering must try to reach as many decisions as possible in the drawing office by drawing cross sections of the earthwork. On the site when further information becomes available he can make changes in jis sections and layout,but the drawing lffice work will not have been lost. It will have helped him to reach the best solution in the shortest time.

The cheapest way of moving earth is to take it directly out of the cut and drop it as fill with the same machine. This is not always possible, but when it canbe done it is ideal, being both quick and cheap. Draglines, bulldozers and face shovels an do this. The largest radius is obtained with the dragline,and the largest tonnage of earth is moved by the bulldozer, though only over short distances.The disadvantages of the dragline are that it must dig below itself, it cannot dig with force into compacted material, it cannot dig on steep slopws, and its dumping and digging are not accurate.

Face shovels are between bulldozers and draglines, having a larger radius of action than bulldozers but less than draglines. They are anle to dig into a vertical cliff face in a way which would be dangerous tor a bulldozer operator and impossible for a dragline. Each piece of equipment should be level of their tracks and for deep digs in compact material a backacter is most useful, but its dumping radius is considerably less than that of the same escavator fitted with a face shovel.

Rubber-tyred bowl scrapers are indispensable for fairly level digging where the distance of transport is too much tor a dragline or face shovel. They can dig the material deeply ( but only below themselves ) to a fairly flat surface, carry it hundreds of meters if need be, then drop it and level it roughly during the dumping. For hard digging it is often found economical to keep a pusher tractor ( wheeled or tracked ) on the digging site, to push each scraper as it returns to dig. As soon as the scraper is full,the pusher tractor returns to the beginning of the dig to heop to help the nest scraper.

Bowl scrapers are often extremely powerful machines;many makers build scrapers

of 8 cubic meters struck capacity, which carry 10 m 3 heaped. The largest self-propelled scrapers are of 19 m 3 struck capacity ( 25 m 3 heaped )and they are driven by a tractor engine of 430 horse-powers.

Dumpers are probably the commonest rubber-tyred transport since they can also conveniently be used for carrying concrete or other building materials. Dumpers have the earth container over the front axle on large rubber-tyred wheels, and the container tips forwards on most types, though in articulated dumpers the direction of tip can be widely varied. The smallest dumpers have a capacity of about 0.5 m 3, and the largest standard types are of about 4.5 m 3. Special types include the self-loading dumper of up to 4 m 3and the articulated type of about 0.5 m 3. The distinction between dumpers and dump trucks must be remembered .dumpers tip forwards and the driver sits behind the load. Dump trucks are heavy, strengthened tipping lorries, the driver travels in front lf the load and the load is dumped behind him, so they are sometimes called rear-dump trucks.

2.3 Safety of Structures

The principal scope of specifications is to provide general principles and computational methods in order to verify safety of structures. The “ safety factor ”, which according to modern trends is independent of the nature and combination of the materials used, can usually be defined as the ratio between the conditions. This ratio is also proportional to the inverse of the probability ( risk ) of failure of the structure.

Failure has to be considered not only as overall collapse of the structure but also as unserviceability or, according to a more precise. Common definition. As the reaching of a “ limit state ” which causes the construction not to accomplish the task it was d esigned for. There are two categories of limit state :

(1)Ultimate limit sate, which corresponds to the highest value of the load-bearing capacity. Examples include local buckling or global instability of the structure; failure of some sections and subsequent transformation of the structure into a mechanism; failure by fatigue; elastic or plastic deformation or creep that cause a substantial change of the geometry of the structure; and sensitivity of the structure to alternating loads, to fire and to explosions.

(2)Service limit states, which are functions of the use and durability of the structure. Examples include excessive deformations and displacements without instability; early or excessive cracks; large vibrations; and corrosion.

Computational methods used to verify structures with respect to the different safety

conditions can be separated into:

(1)Deterministic methods, in which the main parameters are considered as nonrandom parameters.

(2)Probabilistic methods, in which the main parameters are considered as random parameters.

Alternatively, with respect to the different use of factors of safety, computational methods can be separated into:

(1)Allowable stress method, in which the stresses computed under maximum loads are compared with the strength of the material reduced by given safety factors.

(2)Limit states method, in which the structure may be proportioned on the basis of its maximum strength. This strength, as determined by rational analysis, shall not be less than that required to support a factored load equal to the sum of the factored live load and dead load ( ultimate state ).

The stresses corresponding to working ( service ) conditions with unfactored live and dead loads are compared with prescribed values ( service limit state ) . From the four possible combinations of the first two and second two methods, we can obtain some useful computational methods. Generally, two combinations prevail:

(1)deterministic methods, which make use of allowable stresses.

(2)Probabilistic methods, which make use of limit states.

The main advantage of probabilistic approaches is that, at least in theory, it is possible to scientifically take into account all random factors of safety, which are then combined to define the safety factor. probabilistic approaches depend upon :

(1) Random distribution of strength of materials with respect to the conditions of fabrication and erection ( scatter of the values of mechanical properties through out the structure );

(2) Uncertainty of the geometry of the cross-section sand of the structure ( faults and imperfections due to fabrication and erection of the structure );

(3) Uncertainty of the predicted live loads and dead loads acting on the structure;

(4)Uncertainty related to the approximation of the computational method used ( deviation of the actual stresses from computed stresses ).

Furthermore, probabilistic theories mean that the allowable risk can be based on several factors, such as :

(1) Importance of the construction and gravity of the damage by its failure;

(2)Number of human lives which can be threatened by this failure;

(3)Possibility and/or likelihood of repairing the structure;

(4) Predicted life of the structure.

All these factors are related to economic and social considerations such as：

(1) Initial cost of the construction;

(2) Amortization funds for the duration of the construction;

(3) Cost of physical and material damage due to the failure of the construction;

(4) Adverse impact on society;

(5) Moral and psychological views.

The definition of all these parameters, for a given safety factor, allows construction at the optimum cost. However, the difficulty of carrying out a complete probabilistic analysis has to be taken into account. For such an analysis the laws of the distribution of the live load and its induced stresses, of the scatter of mechanical properties of materials, and of the geometry of the cross-sections and the structure have to be known. Furthermore, it is difficult to interpret the interaction between the law of distribution of strength and that of stresses because both depend upon the nature of the material, on the cross-sections and upon the load acting on the structure. These practical difficulties can be overcome in two ways. The first is to apply different safety factors to the material and to the loads, without necessarily adopting the probabilistic criterion. The second is an approximate probabilistic method which introduces some simplifying assumptions ( semi-probabilistic methods ) .

土木工程类专业英文文献及翻译

PA VEMENT PROBLEMS CAUSED BY COLLAPSIBLE SUBGRADES By Sandra L. Houston,1 Associate Member, ASCE (Reviewed by the Highway Division) ABSTRACT: Problem subgrade materials consisting of collapsible soils are com- mon in arid environments, which have climatic conditions and depositional and weathering processes favorable to their formation. Included herein is a discussion of predictive techniques that use commonly available laboratory equipment and testing methods for obtaining reliable estimates of the volume change for these problem soils. A method for predicting relevant stresses and corresponding collapse strains for typical pavement subgrades is presented. Relatively simple methods of evaluating potential volume change, based on results of familiar laboratory tests, are used. INTRODUCTION When a soil is given free access to water, it may decrease in volume, increase in volume, or do nothing. A soil that increases in volume is called a swelling or expansive soil, and a soil that decreases in volume is called a collapsible soil. The amount of volume change that occurs depends on the soil type and structure, the initial soil density, the imposed stress state, and the degree and extent of wetting. Subgrade materials comprised of soils that change volume upon wetting have caused distress to highways since the be- ginning of the professional practice and have cost many millions of dollars in roadway repairs. The prediction of the volume changes that may occur in the field is the first step in making an economic decision for dealing with these problem subgrade materials. Each project will have different design considerations, economic con- straints, and risk factors that will have to be taken into account. However, with a reliable method for making volume change predictions, the best design relative to the subgrade soils becomes a matter of economic comparison, and a much more rational design approach may be made. For example, typical techniques for dealing with expansive clays include: (1) In situ treatments with substances such as lime, cement, or fly-ash; (2) seepage barriers and/ or drainage systems; or (3) a computing of the serviceability loss and a mod- ification of the design to "accept" the anticipated expansion. In order to make the most economical decision, the amount of volume change (especially non- uniform volume change) must be accurately estimated, and the degree of road roughness evaluated from these data. Similarly, alternative design techniques are available for any roadway problem. The emphasis here will be placed on presenting economical and simple methods for: (1) Determining whether the subgrade materials are collapsible; and (2) estimating the amount of volume change that is likely to occur in the 'Asst. Prof., Ctr. for Advanced Res. in Transp., Arizona State Univ., Tempe, AZ 85287. Note. Discussion open until April 1, 1989. To extend the closing date one month,

机械设计设计外文文献翻译、中英文翻译、外文翻译

机械设计 摘要：机器是由机械装置和其它组件组成的。它是一种用来转换或传递能量的装置，例如：发动机、涡轮机、车辆、起重机、印刷机、洗衣机、照相机和摄影机等。许多原则和设计方法不但适用于机器的设计，也适用于非机器的设计。术语中的“机械装置设计”的含义要比“机械设计”的含义更为广泛一些，机械装置设计包括机械设计。在分析运动及设计结构时，要把产品外型以及以后的保养也要考虑在机械设计中。在机械工程领域中，以及其它工程领域中，所有这些都需要机械设备，比如：开关、凸轮、阀门、船舶以及搅拌机等。 关键词：设计流程设计规则机械设计 设计流程 设计开始之前就要想到机器的实际性，现存的机器需要在耐用性、效率、重量、速度，或者成本上得到改善。新的机器必需具有以前机器所能执行的功能。 在设计的初始阶段，应该允许设计人员充分发挥创造性，不要受到任何约束。即使产生了许多不切实际的想法，也会在设计的早期，即在绘制图纸之前被改正掉。只有这样，才不致于阻断创新的思路。通常,还要提出几套设计方案，然后加以比较。很有可能在这个计划最后决定中,使用了某些不在计划之内的一些设想。 一般的当外型特点和组件部分的尺寸特点分析得透彻时，就可以全面的设计和分析。接着还要客观的分析机器性能的优越性，以及它的安全、重量、耐用性，并且竞争力的成本也要考虑在分析结果之内。每一个至关重要的部分要优化它的比例和尺寸，同时也要保持与其它组成部分相协调。 也要选择原材料和处理原材料的方法。通过力学原理来分析和实现这些重要的特性，如那些静态反应的能量和摩擦力的最佳利用，像动力惯性、加速动力和能量；包括弹性材料的强度、应力和刚度等材料的物理特性，以及流体润滑和驱动器的流体力学。设计的过程是重复和合作的过程，无论是正式或非正式的进行，对设计者来说每个阶段都很重要。 最后，以图样为设计的标准，并建立将来的模型。如果它的测试是符合事先要

毕业论文英文参考文献与译文

Inventory management Inventory Control On the so-called "inventory control", many people will interpret it as a "storage management", which is actually a big distortion. The traditional narrow view, mainly for warehouse inventory control of materials for inventory, data processing, storage, distribution, etc., through the implementation of anti-corrosion, temperature and humidity control means, to make the custody of the physical inventory to maintain optimum purposes. This is just a form of inventory control, or can be defined as the physical inventory control. How, then, from a broad perspective to understand inventory control? Inventory control should be related to the company's financial and operational objectives, in particular operating cash flow by optimizing the entire demand and supply chain management processes (DSCM), a reasonable set of ERP control strategy, and supported by appropriate information processing tools, tools to achieved in ensuring the timely delivery of the premise, as far as possible to reduce inventory levels, reducing inventory and obsolescence, the risk of devaluation. In this sense, the physical inventory control to achieve financial goals is just a means to control the entire inventory or just a necessary part; from the perspective of organizational functions, physical inventory control, warehouse management is mainly the responsibility of The broad inventory control is the demand and supply chain management, and the whole company's responsibility. Why until now many people's understanding of inventory control, limited physical inventory control? The following two reasons can not be ignored: First, our enterprises do not attach importance to inventory control. Especially those who benefit relatively good business, as long as there is money on the few people to consider the problem of inventory turnover. Inventory control is simply interpreted as warehouse management, unless the time to spend money, it may have been to see the inventory problem, and see the results are often very simple procurement to buy more, or did not do warehouse departments . Second, ERP misleading. Invoicing software is simple audacity to call it ERP, companies on their so-called ERP can reduce the number of inventory, inventory control, seems to rely on their small software can get. Even as SAP, BAAN ERP world, the field of

数学专业外文文献翻译

第3章 最小均方算法 3．1 引言 最小均方(LMS ,least-mean-square)算法是一种搜索算法，它通过对目标函数进行适当的调整[1]—[2],简化了对梯度向量的计算。由于其计算简单性，LMS 算法和其他与之相关的算法已经广泛应用于白适应滤波的各种应用中[3]-[7]。为了确定保证稳定性的收敛因子范围，本章考察了LMS 算法的收敛特征。研究表明，LMS 算法的收敛速度依赖于输入信号相关矩阵的特征值扩展[2]—[6]。在本章中，讨论了LMS 算法的几个特性，包括在乎稳和非平稳环境下的失调[2]—[9]和跟踪性能[10]-[12]。本章通过大量仿真举例对分析结果进行了证实。在附录B 的B ．1节中，通过对LMS 算法中的有限字长效应进行分析，对本章内容做了补充。 LMS 算法是自适应滤波理论中应用最广泛的算法，这有多方面的原因。LMS 算法的 主要特征包括低计算复杂度、在乎稳环境中的收敛性、其均值无俯地收敛到维纳解以及利用有限精度算法实现时的稳定特性等。 3．2 LMS 算法 在第2章中，我们利用线性组合器实现自适应滤波器，并导出了其参数的最优解，这对应于多个输入信号的情形。该解导致在估计参考信号以d()k 时的最小均方误差。最优(维纳)解由下式给出： 1 0w R p -= (3.1) 其中，R=E[()x ()]T x k k 且p=E[d()x()] k k ，假设d()k 和x()k 联合广义平稳过程。 如果可以得到矩阵R 和向量p 的较好估计，分别记为()R k ∧和()p k ∧ ，则可以利用如下最陡下降算法搜索式(3．1)的维纳解： w(+1)=w()-g ()w k k k μ∧ w()(()()w())k p k R k k μ∧∧ =-＋２ (3.2) 其中，k ＝0，1，2，…,g ()w k ∧ 表示目标函数相对于滤波器系数的梯度向量估计值。

土木工程岩土类毕业设计外文翻译

姓名： 学号： 10447425 X X 大学 毕业设计（论文）外文翻译 （2014届） 外文题目Developments in excavation bracing systems 译文题目开挖工程支撑体系的发展 外文出处Tunnelling and Underground Space Technology 31 (2012) 107–116 学生XXX 学院XXXX 专业班级XXXXX 校内指导教师XXX 专业技术职务XXXXX 校外指导老师专业技术职务 二○一三年十二月

开挖工程支撑体系的发展 1.引言 几乎所有土木工程建设项目（如建筑物，道路，隧道，桥梁，污水处理厂，管道，下水道）都涉及泥土挖掘的一些工程量。往往由于由相邻的结构，特性线，或使用权空间的限制，必须要一个土地固定系统，以允许土壤被挖掘到所需的深度。历史上，许多挖掘支撑系统已经开发出来。其中，现在比较常见的几种方法是：板桩，钻孔桩墙，泥浆墙。 土地固定系统的选择是由技术性能要求和施工可行性（例如手段，方法）决定的，包括执行的可靠性，而成本考虑了这些之后，其他问题也得到解决。通常环境后果（用于处理废泥浆和钻井液如监管要求）也非常被关注（邱阳、1998）。 土地固定系统通常是建设项目的较大的一个组成部分。如果不能按时完成项目，将极大地影响总成本。通常首先建造支撑，在许多情况下，临时支撑系统是用于支持在挖掘以允许进行不断施工，直到永久系统被构造。临时系统可以被去除或留在原处。 打桩时，因撞击或振动它们可能会被赶入到位。在一般情况下，振动是最昂贵的方法，但只适合于松散颗粒材料，土壤中具有较高电阻（例如，通过鹅卵石）的不能使用。采用打入桩系统通常是中间的成本和适合于软沉积物（包括粘性和非粘性），只要该矿床是免费的鹅卵石或更大的岩石。 通常，垂直元素（例如桩）的前安装挖掘工程和水平元件（如内部支撑或绑回）被安装为挖掘工程的进行下去，从而限制了跨距长度，以便减少在垂直开发弯矩元素。在填充情况下，桩可先设置，从在斜坡的底部其嵌入悬挑起来，安装作为填充进步水平元素（如搭背或土钉）。如果滞后是用来保持垂直元素之间的土壤中，它被安装为挖掘工程的进行下去，或之前以填补位置。 吉尔- 马丁等人（2010）提供了一个数值计算程序，以获取圆形桩承受轴向载荷和统一标志（如悬臂桩）的单轴弯矩的最佳纵筋。他们开发的两种优化流程：用一个或两个直径为纵向钢筋。优化增强模式允许大量减少的设计要求钢筋的用量，这些减少纵向钢筋可达到50％相对传统的，均匀分布的加固方案。 加固桩集中纵向钢筋最佳的位置在受拉区。除了节约钢筋，所述非对称加强钢筋图案提高抗弯刚度，通过增加转动惯量的转化部分的时刻。这种增加的刚性可能会在一段时间内增加的变形与蠕变相关的费用。评估相对于传统的非对称加强桩的优点，对称，钢筋桩被服务的条件下全面测试来完成的，这种试验是为了验证结构的可行性和取得的变形的原位测量。 基于现场试验中，用于优化的加强图案的优点浇铸钻出孔（CIDH）在巴塞罗那的

平面设计中英文对照外文翻译文献

(文档含英文原文和中文翻译) 中英文翻译 平面设计 任何时期平面设计可以参照一些艺术和专业学科侧重于视觉传达和介绍。采用多种方式相结合，创造和符号，图像和语句创建一个代表性的想法和信息。平面设计师可以使用印刷，视觉艺术和排版技术产生的最终结果。平面设计常常提到的进程，其中沟通是创造和产品设计。 共同使用的平面设计包括杂志，广告，产品包装和网页设计。例如，可能包括产品包装的标志或其他艺术作品，举办文字和纯粹的设计元素，如形状和颜色统一件。组成的一个最重要的特点，尤其是平面设计在使用前现有材料或不同的元素。 平面设计涵盖了人类历史上诸多领域，在此漫长的历史和在相对最近爆炸视觉传达中的第20和21世纪，人们有时是模糊的区别和重叠的广告艺术，平面设计和美术。毕竟，他们有着许多相同的内容，理论，原则，做法和语言，有时同样的客人或客户。广告艺术的最终目标是出售的商品和服务。在平面

设计，“其实质是使以信息，形成以思想，言论和感觉的经验”。 在唐朝（ 618-906 ）之间的第4和第7世纪的木块被切断打印纺织品和后重现佛典。阿藏印在868是已知最早的印刷书籍。 在19世纪后期欧洲，尤其是在英国，平面设计开始以独立的运动从美术中分离出来。蒙德里安称为父亲的图形设计。他是一个很好的艺术家，但是他在现代广告中利用现代电网系统在广告、印刷和网络布局网格。 于1849年，在大不列颠亨利科尔成为的主要力量之一在设计教育界，该国政府通告设计在杂志设计和制造的重要性。他组织了大型的展览作为庆祝现代工业技术和维多利亚式的设计。 从1892年至1896年威廉?莫里斯凯尔姆斯科特出版社出版的书籍的一些最重要的平面设计产品和工艺美术运动，并提出了一个非常赚钱的商机就是出版伟大文本论的图书并以高价出售给富人。莫里斯证明了市场的存在使平面设计在他们自己拥有的权利，并帮助开拓者从生产和美术分离设计。这历史相对论是，然而，重要的，因为它为第一次重大的反应对于十九世纪的陈旧的平面设计。莫里斯的工作，以及与其他私营新闻运动，直接影响新艺术风格和间接负责20世纪初非专业性平面设计的事态发展。 谁创造了最初的“平面设计”似乎存在争议。这被归因于英国的设计师和大学教授Richard Guyatt，但另一消息来源于20世纪初美国图书设计师William Addison Dwiggins。 伦敦地铁的标志设计是爱德华约翰斯顿于1916年设计的一个经典的现代而且使用了系统字体设计。 在20世纪20年代，苏联的建构主义应用于“智能生产”在不同领域的生产。个性化的运动艺术在俄罗斯大革命是没有价值的，从而走向以创造物体的功利为目的。他们设计的建筑、剧院集、海报、面料、服装、家具、徽标、菜单等。 Jan Tschichold 在他的1928年书中编纂了新的现代印刷原则，他后来否认他在这本书的法西斯主义哲学主张，但它仍然是非常有影响力。 Tschichold ，包豪斯印刷专家如赫伯特拜耳和拉斯洛莫霍伊一纳吉，和El Lissitzky 是平面设计之父都被我们今天所知。 他们首创的生产技术和文体设备，主要用于整个二十世纪。随后的几年看到平面设计在现代风格获得广泛的接受和应用。第二次世界大战结束后，美国经济的建立更需要平面设计，主要是广告和包装等。移居国外的德国包豪斯设计学院于1937年到芝加哥带来了“大规模生产”极简到美国;引发野火的“现代”建筑和设计。值得注意的名称世纪中叶现代设计包括阿德里安Frutiger ，设计师和Frutiger字体大学;保兰德，从20世纪30年代后期，直到他去世于1996年，采取的原则和适用包豪斯他们受欢迎的广告和标志设计，帮助创造一个独特的办法，美国的欧洲简约而成为一个主要的先驱。平面设计称为企业形象;约瑟夫米勒，罗克曼，设计的海报严重尚未获取1950年代和1960年代时代典型。 从道路标志到技术图表，从备忘录到参考手册，增强了平面设计的知识转让。可读性增强了文字的视觉效果。 设计还可以通过理念或有效的视觉传播帮助销售产品。将它应用到产品和公司识别系统的要素像标志、颜色和文字。连同这些被定义为品牌。品牌已日益成为重要的提供的服务范围，许多平面设计师，企业形象和条件往往是同时交替使用。

机械专业外文翻译(中英文翻译)

外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important considerations in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems covering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11-and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are

大学毕业论文---软件专业外文文献中英文翻译

软件专业毕业论文外文文献中英文翻译 Object landscapes and lifetimes Tech nically, OOP is just about abstract data typing, in herita nee, and polymorphism, but other issues can be at least as importa nt. The rema in der of this sect ion will cover these issues. One of the most importa nt factors is the way objects are created and destroyed. Where is the data for an object and how is the lifetime of the object con trolled? There are differe nt philosophies at work here. C++ takes the approach that con trol of efficie ncy is the most importa nt issue, so it gives the programmer a choice. For maximum run-time speed, the storage and lifetime can be determined while the program is being written, by placing the objects on the stack (these are sometimes called automatic or scoped variables) or in the static storage area. This places a priority on the speed of storage allocatio n and release, and con trol of these can be very valuable in some situati ons. However, you sacrifice flexibility because you must know the exact qua ntity, lifetime, and type of objects while you're writing the program. If you are trying to solve a more general problem such as computer-aided desig n, warehouse man ageme nt, or air-traffic con trol, this is too restrictive. The sec ond approach is to create objects dyn amically in a pool of memory called the heap. In this approach, you don't know un til run-time how many objects you n eed, what their lifetime is, or what their exact type is. Those are determined at the spur of the moment while the program is runnin g. If you n eed a new object, you simply make it on the heap at the point that you n eed it. Because the storage is man aged dyn amically, at run-time, the amount of time required to allocate storage on the heap is sig ni fica ntly Ion ger tha n the time to create storage on the stack. (Creat ing storage on the stack is ofte n a si ngle assembly in structio n to move the stack poin ter dow n, and ano ther to move it back up.) The dyn amic approach makes the gen erally logical assumpti on that objects tend to be complicated, so the extra overhead of finding storage and releas ing that storage will not have an importa nt impact on the creati on of an object .In additi on, the greater flexibility is esse ntial to solve the gen eral program ming problem. Java uses the sec ond approach, exclusive". Every time you want to create an object, you use the new keyword to build a dyn amic in sta nee of that object. There's ano ther issue, however, and that's the lifetime of an object. With Ian guages that allow objects to be created on the stack, the compiler determines how long the object lasts and can automatically destroy it. However, if you create it on the heap the compiler has no kno wledge of its lifetime. In a Ianguage like C++, you must determine programmatically when to destroy the

数学专业外文文献翻译

第3章最小均方算法 3．1 引言 最小均方(LMS,least-mean-square)算法是一种搜索算法，它通过对目标函数进行适当的调整[1]—[2],简化了对梯度向量的计算。由于其计算简单性，LMS算法和其他与之相关的算法已经广泛应用于白适应滤波的各种应用中[3]-[7]。为了确定保证稳定性的收敛因子范围，本章考察了LMS算法的收敛特征。研究表明，LMS算法的收敛速度依赖于输入信号相关矩阵的特征值扩展[2]—[6]。在本章中，讨论了LMS算法的几个特性，包括在乎稳和非平稳环境下的失调[2]—[9]和跟踪性能[10]-[12]。本章通过大量仿真举例对分析结果进行了证实。在附录B的B．1节中，通过对LMS算法中的有限字长效应进行分析，对本章内容做了补充。 LMS算法是自适应滤波理论中应用最广泛的算法，这有多方面的原因。LMS算法的主要特征包括低计算复杂度、在乎稳环境中的收敛性、其均值无俯地收敛到维纳解以及利用有限精度算法实现时的稳定特性等。 3．2 LMS算法 1 / 29

2 / 29 在第2章中，我们利用线性组合器实现自适应滤波器，并导出了其参数的最优解，这对应于多个输入信号的情形。该解导致在估计参考信号以d()k 时的最小均方误差。最优(维纳)解由下式给出： 1 0w R p -=(3.1) 其中，R=E[()x ()]T x k k 且p=E[d()x()] k k ，假设d()k 和x()k 联合广义平稳过程。 如果可以得到矩阵R 和向量p 的较好估计，分别记为()R k ∧ 和 ()p k ∧ ，则可以利用如下最陡下降算法搜索式(3．1)的维纳解： w(+1)=w()-g ()w k k k μ∧ w()(()()w())k p k R k k μ∧∧ =-＋２(3.2) 其中，k ＝0，1，2，…,g ()w k ∧ 表示目标函数相对于滤波器系数的梯度向量估计值。 一种可能的解是通过利用R 和p 的瞬时估计值来估计梯度向量，即 ()x()x ()T R k k k ∧ = ()()x()p k d k k ∧=(3.3) 得到的梯度估计值为

土木工程专业外文文献及翻译

（ 二 〇 一 二 年 六 月 外文文献及翻译 题 目： About Buiding on the Structure Design 学生姓名： 学 院：土木工程学院 系 别：建筑工程系 专 业：土木工程(建筑工程方向) 班 级：土木08-4班 指导教师：

英文原文： Building construction concrete crack of prevention and processing Abstract The crack problem of concrete is a widespread existence but again difficult in solve of engineering actual problem, this text carried on a study analysis to a little bit familiar crack problem in the concrete engineering, and aim at concrete the circumstance put forward some prevention, processing measure. Keyword:Concrete crack prevention processing Foreword Concrete's ising 1 kind is anticipate by the freestone bone, cement, water and other mixture but formation of the in addition material of quality brittleness not and all material.Because the concrete construction transform with oneself, control etc. a series problem, harden model of in the concrete existence numerous tiny hole, spirit cave and tiny crack, is exactly because these beginning start blemish of existence just make the concrete present one some not and all the characteristic of quality.The tiny crack is a kind of harmless crack and accept concrete heavy, defend Shen and a little bit other use function not a creation to endanger.But after the concrete be subjected to lotus carry, difference in temperature etc. function, tiny crack would continuously of expand with connect, end formation we can see without the

包装设计外文翻译文献

包装设计外文翻译文献(文档含中英文对照即英文原文和中文翻译)

包装对食品发展的影响 消费者对某个产品的第一印象来说包装是至关重要的，包括沟通的可取性，可接受性，健康饮食形象等。食品能够提供广泛的产品和包装组合，传达自己加工的形象感知给消费者，例如新鲜包装/准备，冷藏，冷冻，超高温无菌，消毒（灭菌），烘干产品。 食物的最重要的质量属性之一，是它的味道，其影响人类的感官知觉，即味觉和嗅觉。味道可以很大程度作退化的处理和/或扩展存储。其他质量属性，也可能受到影响，包括颜色，质地和营养成分。食品质量不仅取决于原材料，添加剂，加工和包装的方法，而且其预期的货架寿命（保质期）过程中遇到的运输和储存条件的质量。越来越多的竞争当中，食品生产商，零售商和供应商；和质量审核供应商有着显著的提高食品质量以及急剧增加包装食品的选择。这些改进也得益于严格的冷藏链中的温度控制和越来越挑剔的消费者。 保质期的一个定义是：在规定的贮存温度条件下产品保持其质量和安全性的时间。在保质期内，产品的生产企业对该产品质量符合有关标准或明示担保的质量条件负责，销售者可以放心销售这些产品，消费者可以安全使用。 保质期不是识别食物等产品是否变质的唯一标准，可能由于存放方式，环境等变化物质的过早变质。所以食物等尽量在保质期未到期就及时食用。包装产品的质量和保质期的主题是在第3章中详细讨论。

包装为消费者提供有关产品的重要信息，在许多情况下，使用的包装和/或产品，包括事实信息如重量，体积，配料，制造商的细节，营养价值，烹饪和开放的指示，除了法律准则的最小尺寸的文字和数字，有定义的各类产品。消费者寻求更详细的产品信息，同时，许多标签已经成为多语种。标签的可读性会是视觉发现的一个问题，这很可能成为一个对越来越多的老年人口越来越重要的问题。 食物的选择和包装创新的一个主要驱动力是为了方便消费者的需求。这里有许多方便的现代包装所提供的属性，这些措施包括易于接入和开放，处置和处理，产品的知名度，再密封性能，微波加热性，延长保质期等。在英国和其他发达经济体显示出生率下降和快速增长的一个相对富裕的老人人口趋势，伴随着更加苛刻的年轻消费者，他们将要求和期望改进包装的功能，如方便包开启（百货配送研究所，IGD）。 对零售商而言存在有一个高的成本，供应和服务的货架体系。没有储备足够的产品品种或及时补充库存，特别是副食品，如鲜牛奶，可能导致客户不满和流失到竞争对手的商店，这正需要保证产品供应。现代化的配送和包装系统，允许消费者在购买食品时，他们希望在他们想任何时间地点都能享用。近几年消费者的选择已在急剧扩大。例如在英国，20世纪60年代和90年代之间在一般超市的产品线的数量从2000年左右上升到超过18000人（INCPEN）。 自20世纪70年代以来，食品卫生和安全问题已成为日益重要的关注和选择食物的驱动力。媒体所关注的一系列问题，如使用化学添