组装、冲压、喷漆等专业词汇
Layout布置图
fixture 夹具(治具)
pallet栈板
barcode条码
熔机
repair修理
operator作业员
QC品管
supervisor 课长
ME制造工程师
MT制造生技
lbs. inch镑、英寸
chassis基座
bezel panel面板
sheet metal parts 冲件
work cell工作间
personnel resource department
人力资源部
production department生产部门
planning department企划部
QC Section品管科
stamping factory冲压厂
painting factory烤漆厂
molding factory成型厂
common equipment常用设备
uncoiler and straightener整平机
punching machine 冲床
robot机械手
hydraulic machine油压机
lathe车床
planer |'plein|刨床
miller铣床
grinder磨床
driller??床
welder电焊机
staker=reviting machine铆合机
position职务
president董事长
general manager总经理
special assistant manager特助
factory director厂长
department director部长
deputy manager | =vice manager副理
section supervisor课长
deputy section supervisor =vice section superisor副课长group leader/supervisor组长
line supervisor线长
assistant manager助理
to move, to carry, to handle搬运
be put in storage入库
pack packing包装
to apply oil擦油
to 锉毛刺
final inspection终检
cleaning cloth抹布
scrape ..v.刮;削
manufacture procedure制程
oxidation |' ksi'dein|氧化
scratch刮伤
dents压痕
production capacity生产力
proposal improvement提案改善
spare parts=buffer备件
trailer=long vehicle拖板车
pressure plate=plate pinch压板
bolt螺栓
name of a department部门名称administration/general affairs dept总务部power wire电源线
buzzle蜂鸣器
pedal踩踏板
stopper阻挡器
glove(s)手套
iudustrial alcohol工业酒精
sweeper扫把
mop拖把
vaccum cleaner吸尘器
rag 抹布
garbage container灰箕
garbage can垃圾箱
garbage bag垃圾袋
chain链条
jack升降机
production line流水线
to mop the floor拖地
to clean the floor扫地
to clean a table擦桌子
air pipe 气管
packaging tool打包机
packaging打包
missing part漏件
excessive defects过多的缺陷
critical defect极严重缺陷
major defect主要缺陷
minor defect次要缺陷
not up to standard不合规格
dimension/size is a little bigger尺寸偏大(小) slipped screwhead/slippery screw head螺丝滑头speckle斑点
mildewed=moldy=mouldy发霉
rust生锈
deformation变形
burr(金属)flash(塑件)毛边
grease/oil stains油污
inclusion杂质
shrinking/shrinkage缩水
mixed color杂色
scratch划伤
painting make-up补漆
discoloration羿色
water spots水渍
polishing/surface processing表面处理exposed metal/bare metal金属裸露
lack of painting烤漆不到位
safety安全
quality品质
delivery deadline交货期
cost成本
engineering工程
enterprise plan = enterprise expansion projects企划
QC品管
production, to produce生产
equipment设备
to start a press开机
stop/switch off a press关机
classification整理
regulation整顿
cleanness清扫
conservation清洁
qualified products, up-to-grade products良品
defective products, not up-to-grade products不良品
waste废料
feeder送料机
sliding rack滑料架
packing material包材
isolating plate baffle plate; barricade隔板
carton box纸箱
to pull and stretch拉深
to put material in place, to cut material,
to compress, compressing压缩
to feed, feeding送料
transportation运输
(be)qualfied, up to grade合格
not up to grade, not qualified不合格
material change, stock change材料变更
evaluation评估
prepare for, make preparations for 准备
parameters参数
rotating speed, revolution转速
manufacture management制造管理
abnormal handling异常处理
production unit生产单位
lots of production生产批量
steel plate钢板
roll material卷料
to revise, modify修订
to switch over to, switch---to throw--over switching over切换stage die工程模
automation自动化
to stake, staking, reviting铆合
add lubricating oil加润滑油
argon welding氩焊
vocabulary for stamping
冲压常词汇
stamping, press冲压
punch press, dieing out press冲床
uncoiler & strainghtener整平机
feeder送料机
rack, shelf, stack料架
cylinder油缸
robot机械手
taker取料机
conveyer belt输送带
transmission rack输送架
one stroke一行程
inch寸动
to continue, cont.连动
to grip(material)吸料
location lump, locating piece, block stop 定位块reset复位
smoothly顺利
filings铁削
to draw holes抽孔
inquiry, search for查寻
to stock, storage, in stock库存
receive领取
approval examine and verify审核processing, to process加工
delivery, to deliver 交货
to return delivenry to.
to send delinery back
to retrn of goods退货
registration登记
registration card登记卡
to control管制
to put forward and hand in提报
safe stock安全库存
acceptance = receive验收
to notice通知
application form for purchase请购单consume, consumption消耗
to fill in填写
abrasion磨损
reverse angle = chamfer倒角
character die字模
to collect, to gather收集
failure, trouble故障
statistics统计
demand and supply需求
career card履历卡
to take apart a die卸下模具
to load a die装上模具
to tight a bolt拧紧螺栓
to looser a bolt拧松螺栓
easily damaged parts易损件
standard parts标准件
breaking.(be)broken,(be)cracked 断裂
to lubricate润滑
common vocabulary for die engineering
模具工程常用词汇
die 模具
punched hole冲孔
panel board镶块
to cutedges=side cut=side scrap切边
to bending折弯
to pull, to stretch拉伸
Line streching, line pulling线拉伸engraving, to engrave刻印
upsiding down edges翻边
to stake铆合
designing, to design设计
design modification设计变化
die block模块
folded block折弯块
sliding block滑块
location pin定位销
lifting pin顶料销
die plate, front board模板
padding block垫块
stepping bar垫条
spring 弹簧
bolt螺栓
document folder文件夹
r资料夹
to put order整理资料
equipment设备
waste materials废料
casing = containerazation装箱
the first page第一联
end-user/using unit(department)使用单位
summary of year-end physical inventory bills
年终盘点截止单据汇总表
bill name单据名称
plate电镀
mold成型
material for engineering mold testing工程试模材料sample样品
incoming material to be inspected进货待验description品名
steel/rolled steel钢材
material statistics sheet
物料统计明细表
meeting minutes会议记录
meeting type 会别
distribution department分发单位
location地点
chairman主席
present members出席人员
subject主题
conclusion结论
decision items决议事项
responsible department负责单位
pre-fixed finishing date预定完成日
approved by / checked by / prepared by核准/审核/承办revision版次
remark备注
production control confirmation生产确认
checked by初审
approved by核准
department部门
on-hand inventory现有库存
available material良品可使用
to be inspected or reworked
待验或重工
total合计
cause description原因说明
part number/ P/N 料号
type形态
item/group/class类别
quality品质
prepared by制表
notes说明
cause analysis原因分析
raw materials原料
materials物料
finished product成品
semi-finished product半成品
packing materials包材
good product/accepted goods/ accepted parts/good parts良品defective product/non-good parts不良品
disposed goods处理品
warehouse/hub仓库
skid/pallet栈板
tox machine自铆机
wire EDM线割
EDM放电机
coil stock卷料
sheet stock片料
tolerance工差
score=groove压线
cam block滑块
expansion dwg展开图
radius半径
shim(wedge)楔子
torch-flame cut火焰切割
stop pin定位销
stock locater block定位块
active plate活动板
baffle plate挡块
cover plate盖板
bushing block衬套
insert 入块
capability能力
parameter参数
factor系数
alkalidipping脱脂
demagnetization去磁;消磁
high-speed transmission高速传递
heat dissipation热传
rack上料
degrease脱脂
rinse水洗
Chromate铬酸处理
Anodize阳性处理
seal封孔
part number/P/N料号
good products良品
scraped products报放心品
defective products不良品
finished products成品
disposed products处理品
barcode条码
flow chart流程表单
assembly组装
stamping冲压
molding成型
coordinate座标
auxiliary fuction辅助功能
heater band 加热片
thermocouple热电偶
sand blasting喷沙
grit 砂砾
derusting machine除锈机degate打浇口
dryer烘干机
induction感应
induction light感应光
response=reaction=interaction感应ram连杆
concave凸
convex凹
nick缺口
speck瑕??
shine亮班
splay 银纹
gas mark焦痕
delamination起鳞
cold slug冷块
blush 导色
gouge沟槽;凿槽
satin texture段面咬花
patent专利
grit沙砾
granule=peuet=grain细粒
grit maker抽粒机
cushion缓冲
magnalium镁铝合金magnesium镁金
metal plate钣金
lathe车
mill锉
plane刨
grind磨
drill铝
boring镗
blinster气泡
fillet镶;嵌边
through-hole form通孔形式voller pin formality滚针形式cam driver铡楔
shank摸柄
crank shaft曲柄轴
augular offset角度偏差
velocity速度
production tempo生产进度现状torque扭矩
spline=the multiple keys花键quenching淬火
tempering回火
annealing退火
carbonization碳化
alloy合金
tungsten high speed steel钨高速的moly high speed steel钼高速的organic solvent有机溶剂
liaison联络单
volatile挥发性
resistance电阻
ion离子
beacon警示灯
coolant冷却液
crusher破碎机
模具工程类
plain die简易模
pierce die冲孔模
forming die成型模progressive die连续模
gang dies复合模
shearing die剪边模
riveting die铆合模
pierce冲孔
forming成型(抽凸,冲凸)
draw hole抽孔
bending折弯
trim切边
emboss凸点
dome凸圆
semi-shearing半剪
stamp mark冲记号
deburr or coin压毛边
punch riveting冲压铆合
side stretch侧冲压平
reel stretch卷圆压平
groove压线
blanking下料
stamp letter冲字(料号) shearing剪断
tick-mark nearside正面压印tick-mark farside反面压印
冲压名称类
extension dwg展开图procedure dwg工程图
die structure dwg模具结构图material材质
material thickness料片厚度factor系数
upward向上
downward向下
press specification冲床规格burr毛边
gap间隙
weight重量
total wt.总重量
五金零件类
inner guiding post内导柱
inner hexagon screw内六角螺钉dowel pin固定销
coil spring弹簧
lifter pin顶料销
pin销
wire spring圆线弹簧
stop screw止付螺丝
located pin定位销
outer bush外导套
模板类
top plate上托板(顶板)
top block上垫脚
punch pad上垫板
punch holder上夹板
stripper pad脱料背板
up stripper上脱料板
male die公模(凸模)
feature die公母模
female die母模(凹模)
upper plate上模板
lower plate下模板
die pad下垫板
die holder下夹板
die set下模座
bottom block下垫脚
bottom plate下托板(底板) stripping plate内外打(脱料板) outer stripper外脱料板
inner stripper内脱料板
lower stripper下脱料板
零件类
punch冲头
insert入块(嵌入件) deburring punch压毛边冲子groove punch压线冲子stamped punch字模冲子round punch圆冲子
special shape punch异形冲子bending block折刀
roller滚轴
baffle plate挡块
located block定位块supporting block for location
机械专业英语词汇(大全) 金属切削metal cutting 机床machine tool 金属工艺学technology of metals 刀具cutter 摩擦friction 联结link 传动drive/transmission 轴shaft 弹性elasticity 频率特性frequency characteristic 误差error 响应response 定位allocation 机床夹具jig 动力学dynamic 运动学kinematic 静力学static 分析力学analyse mechanics 拉伸pulling 压缩hitting 剪切shear 扭转twist 弯曲应力bending stress 强度intensity 三相交流电three-phase AC 磁路magnetic circles 变压器transformer 异步电动机asynchronous motor 几何形状geometrical 精度precision 正弦形的sinusoid 交流电路AC circuit 机械加工余量machining allowance 变形力deforming force 变形deformation 应力stress 硬度rigidity 热处理heat treatment 退火anneal 正火normalizing 脱碳decarburization 渗碳carburization 电路circuit 半导体元件semiconductor element 反馈feedback 发生器generator 直流电源DC electrical source 门电路gate circuit 逻辑代数logic algebra 外圆磨削external grinding 内圆磨削internal grinding 平面磨削plane grinding 变速箱gearbox 离合器clutch 绞孔fraising 绞刀reamer 螺纹加工thread processing 螺钉screw 铣削mill 铣刀milling cutter 功率power 工件workpiece 齿轮加工gear mechining 齿轮gear 主运动main movement 主运动方向direction of main movement 进给方向direction of feed 进给运动feed movement 合成进给运动resultant movement of feed 合成切削运动resultant movement of cutting 合成切削运动方向direction of resultant movement of cutting 切削深度cutting depth 前刀面rake face 刀尖nose of tool 前角rake angle 后角clearance angle 龙门刨削planing 主轴spindle 主轴箱headstock 卡盘chuck 加工中心machining center
机械类常用英语词汇大全 一字螺丝批 slot type screwdriver 一点透视 one-point perspective 二画 二合一黏合剂 epoxy resin adhesive 二合胶;混合胶 epoxy glue 二维的;平面的 two-dimensional 二进制 binary 二极管;整流子 diode 二号螺丝攻 second tap 二路开关 two-way switch 十进制的;公制的 metric 人工制品 artefact 人造板 man-made board 人体工程学 ergonomics; human engineering 人体尺寸 human dimension 人体测量学 anthropometry; anthropometrics 刀片 blade 刀身 blade 刀具 tool 刀具溜座 carriage 刀柱 tool post 刀架 tool rest 刀架底座 tool rest bracket 刀座帷;床鞍 apron 刀座鞍;溜板座 saddle 力 force 力三角形 triangle of force 力平行四边形 parallelogram of force 力多边形;多边形力学 polygon of force 力的分解 force resolution 力架;亮漆 lacquer 力矩 moment 力偶 couple 力矩定律 law of moment 力-距离图表 force-distance graph 力图 force diagram 力线 line of force 力点 effort 十字榫 cross halving joint 十字螺丝 Philip s head screw 十字螺丝批 Philip s type screwdriver 丁字尺;T 尺 tee square 三画 三爪夹头 three-jaw chuck 三角尺 set square 三角形结构系杆 triangulation tie 三角锉 triangular file 三维的;立体的 three-dimensional 三氯甲烷;哥罗芳 chloroform 三聚氰胺;蜜胺 melamine 三点透视 three-point perspective 上油漆 painting 上釉 enamelling 凡立水 varnish 叉形顶尖 fork centre 口罩 mask 士力;虫漆 shellac 士巴拿;扳手 spanner 大芯夹板;宽条芯夹板 blockboard; solid corestock-laminated board 大量制造 mass production
组装、冲压、喷漆等专业词汇Assembly line组装线Layout布置图 Conveyer流水线物料板Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子 Pneumatic screw driver气动起子 worktable 工作桌 OOBA开箱检查 fit together组装在一起fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器 fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检 查 thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压 测试 Voltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检 查表 work cell工作间 trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产 部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams 共轭曲线conjugate curve 范成法generation method 定义域definitional domain 值域range 导数\\微分differential coefficient 求导derivation 定积分definite integral 不定积分indefinite integral 曲率curvature 偏微分partial differential 毛坯rough 游标卡尺slide caliper 千分尺micrometer calipers 攻丝tap 二阶行列式second order determinant 逆矩阵inverse matrix 线性方程组linear equations 概率probability 随机变量random variable 排列组合permutation and combination 气体状态方程equation of state of gas 动能kinetic energy 势能potential energy 机械能守恒conservation of mechanical energy 动量momentum 桁架truss 轴线axes 余子式cofactor 逻辑电路logic circuit 触发器flip-flop 脉冲波形pulse shape 数模digital analogy 液压传动机构fluid drive mechanism 机械零件mechanical parts 淬火冷却quench 淬火hardening 回火tempering 调质hardening and tempering 磨粒abrasive grain 结合剂bonding agent 砂轮grinding wheel 后角clearance angle 龙门刨削planing 主轴spindle
Lesson 1 Basic Concepts in Mechanics 机械学的基本概念 mechanics n.力学 modify v.修改,调解,变更manageable a.可控制【管理】的 incline v.(使)倾斜 ramp n.斜板,斜坡【道】 slope v.(使)倾斜 friction n.摩擦 roll v.滚动 multiplier n.放大器,乘法器 broom n.扫帚 convert v.转变【化】 handle n.手柄【把】 sweep v.扫荡【描】,掠过efficiency n.效率 gauge vt.测【计】量,校验bearing n.轴承 ideal mechanical advantage 理想的机械效益 neglect vt.忽略Lesson 2 Basic Assumption in Plasticity Theory 塑性理论的基本假设 assumption n.假定 plasticity n.塑性 investigate v.调查,研究deformation n.变形 metal forming process 金属成型工艺【过程】 strain (rate) n.应变【速率】 strength n.强度 stress n.应力 yield stress 屈服应力 flow stress 流动应力 tensile stress 拉【伸】应力compressive stress 压【缩】应力 shear stress 剪【切】应力 geometry n.几何形状 elastic a.弹性的 springback n.回弹 bending n.弯曲,折弯
机械专业英语高频词汇 metal cutting 金属切削 machine tool 机床 technology of metals金属工艺学 cutter 刀具 friction 摩擦 link 联结 drive/transmission 传动 shaft 轴 elasticity 弹性 frequency characteristic 频率特性 error 误差 response响应 allocation 定位 jig 机床夹具 term 语术 d ynamic 动力学 k inematic运动学 s tatic 静力学 a nalyse mechanics 分析力学 p ulling 拉伸 s hear 剪切 t wist 扭转 b ending stress 弯曲应力 i ntensity 强度 t hree-phase AC 三相交流电 m agnetic circles 磁路 t ransformer变压器 a synchronous motor 异步电动机 g eometrical 几何形状 p recision 精度 s inusoid 正弦形的 h itting压缩 A C circuit 交流电路 m achining allowance 机械加工余量 d eforming forc e 变形力 d eformation 变形 s tress 应力 r igidity 硬度 r igidity 刚度 h eat treatment 热处理 d ecarburization 脱碳 c ircuit 电路
f raising铰孔 semiconductor element 半导体元件 f eedback 反馈 g enerator 发生器 D C electrical source直流电源 g ate circuit 门电路 l ogic algebra//////algorithm逻辑代数 e xternal grinding 外圆磨削 internal grinding内圆磨削 p lane grinding 平面磨削 c arburization 渗碳 gearbox 变速箱 c lutch 离合器 r eamer铰刀 t hread processing 螺纹加工 s crew 螺钉 m ill 铣削 m illing cutter 铣刀 p ower 功率 w orkpiece 工件 g ear machining 齿轮加工 g ear 齿轮 m ain movement 主运动 d irection of main movem 主运动方向ent d irection of feed进给方向 f eed movement 进给运动 r esultant movement of fe 合成进给运动ed r esultant movement of cut 合成切削运动ting d irection of resultant cutting 合成切削运动方向motion c utting depth 切削深度 r ake face 前刀面 n ose of tool刀尖 r ake angle 前角 c learance angle 后角 p laning 龙门刨削 s pindle 主轴 h eadstock主轴箱 c huck 卡盘 m achining center 加工中心 l athe tool 车刀 l athe 车床 b ore 钻削镗削 t urning车削 g rinder 磨床
statics and dynamics静动/ journal bearing 径向/ rolling bearing滚动/ stress and strain应力和应变/Strengh of materials材料的强度Shaft轴/coupling连接器/ equivalent load 等效载荷/ stress concentration应力集中/ critical speed临界速度/ rigid coupling刚性连轴器/ flexible coupling挠性联轴器/cotter pin开口销/load limit复合极限/elastic deflection弹性变形thrust bearing推力轴承/ taper roller bearing圆锥滚子轴承/mating surface配合面/Internal spline内花键Lathe车床/headstock主轴箱/tailstock尾架/carriage溜板/leadscrew丝杠/feed rod光杠/engine lathe普通车床/slider-crank mechanism曲柄滑块机构/epicyclic gear行星齿轮/Gear broaching拉齿dimensional tolerance尺寸公差/surface roughness表面粗糙度/upper deviation上偏差/lower deviation下偏差/clearance fit间隙配合/interference fit过盈配合/transition fit过度配合 缩写词:N.C. numerical control数控CAD computer aided design CAE computer aided engineering工程CAM computer aided manufacturing制造/Mechanical Designing-Manufacturing and Automation 机械设计制造及其自动化/Machine design机械设计/mechanical theory机械原理/Engineering drawing工程制图 机床的种类:lathes车床,boring machine镗床,milling machine铣床,planers and shapers刨床和牛头刨床,broaching machines拉床,drilling machines钻孔机 选择连接件时考虑哪些因素:primary function基本功能,appearance外观,a large number of small size fasteners versnus a small number of larger size fasteners对于采用大量的小型连接件还是采用少量的大型连接件的确定,operating condition such as vibration loads and temperature诸如载荷、振动和温度等工作条件,frequency of disassembly装拆频率,adjustability in the location of parts零件位置的可调性,types of materials to be joined被连接零件的材料种类,consequences of failure of loosening of the fastener连接件失效或者松脱造成的后果 弹用途:control of motion in machines控制机构互动,reduction of transmitted forces as aresult of impact of shock loading缓冲减震,storage of energy储存能量,measurement of force测量力的大小 摘要包含哪些内容:state the principal objectives and scope of the investigation阐述该项目研究工作的主要目的和范围,describe the methodology employed描述所使用的方法,summarize the results 总结研究成果,state the principal condusions阐述主要结论 科技论文包括哪些内容:title标题,fact vs opinion事实与意见,the abstract摘要,analysis分析,results and discussion结果和讨论,appendixes附录,important information重要信息,tense,the introduction介绍,experimental procedure实验过程,condusions结论. In addition the shaft must be able to sustain a combination of bending and torsional loads. Thus an equivalent load must be considered which takes into account both torsion a factor of safety which includes fatigue, since torsional and bending stress reversals occur.此外,轴还必须能够承受弯矩的当量载荷。因为扭矩和弯矩会产生交变应力,在许用应力中也应该有一个考虑疲劳现象的安全系数。 Removable. This type permits the parts to be readily disconnected without damaging the fastener. An example is the ordinary nut-and-bolt fastener.可拆式,采用这种方式连接的零件很容易被拆开,而且不会对连接件造成损伤。例如普通的螺栓螺母连接件。 Semipermanent.For this type, the parts can be disconnected ,but some damage usually occurs to the fastener. One such example is a cotter pin .半永久式,采用此类方式连接的零件虽然能被拆开,但通常会对所有的连接件造成损伤。 Permanent. When this type of fastener is used,it is intended that the parts will never be disassembled. Examples are riveted and welded joints.永久式,采用这种连接件就表明所连接的零件不会被分开,例如铆接和焊接。 Design can be based on accepted values of life and it is general practice in the bearing industry to define the load capacity of the bearing as that value below which 90 percent of a batch will exceed a life of one million revolutions.轴承设计是机于能够被人们所承受的寿命来进行的。在轴承行业中,通常将轴承的承载能力定义为这样的值,即所承受的载荷小于这个值时,一批轴承中将会有90%的轴承具有超过一百万的寿命。 Gear hobbing ,the most used metal cutting method,uses the rack generating principle but avoids show reciprocation by mounting many “racks”on a rotating cutter . The “racks”are displaced axially to form a gashed worm (fig.29.3). The gear hobbing process is shown in fig.29. 滚齿是最常见的金属切削方法。它采用齿条展成原理,但是通过安装在旋转刀具上的许多“齿条”来避免缓慢的往复运动。这些“齿条”轴向排布,形成了开槽的蜗杆(见图29.3),滚齿加工过程如图29.4所示。 There are three methods of specitying tolerances on dimensions:unilateral, bilateral, and limit forms. When plus-or-minus tolerancing is used, it is applied to a theoretical dimension called the basic dimension . When dimensions can vary in only one direction from the basic dimension (either larger or smaller )tolerancing is unilateral. Tolerancing that permits variation in both directions from the basic dimension (larger and smaller)is bilateral, tolerances may also be given in limit form, with dimensions representing the largest and smallest sizes for a feature.有三种表示尺寸公差的方式:单向,双向和极限方式。当采用正负公差时,就将公差加到被称为基本尺寸的理想尺寸上去。当只允许尺寸向基本的单一方向(或者变大或者变小)的变动时,就是单向公差。当尺寸在基本尺寸的两个方向(变大或者变小)都可以变动时,公差就是双向的。公差也可以用极限形式给出,表示零件的最大和最小尺寸。
机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ;normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ;Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch
陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker 凸轮cams
机械专业英语 Assembly line组装线 Layout布置图 Conveyer流水线物料板 Rivet table拉钉机 Rivet gun拉钉枪 Screw driver起子 Electric screw driver电动起子Pneumatic screw driver气动起子worktable 工作桌 OOBA开箱检查 fit together组装在一起 fasten锁紧(螺丝) fixture 夹具(治具) pallet栈板 barcode条码 barcode scanner条码扫描器fuse together熔合 fuse machine热熔机 repair修理 operator作业员 QC品管 supervisor 课长 ME制造工程师 MT制造生技 cosmetic inspect外观检查 inner parts inspect内部检查thumb screw大头螺丝 lbs. inch镑、英寸 EMI gasket导电条 front plate前板 rear plate后板 chassis 基座 bezel panel面板 power button电源按键 reset button重置键 Hi-pot test of SPS高源高压测试V oltage switch of SPS 电源电压接拉键 sheet metal parts 冲件 plastic parts塑胶件 SOP制造作业程序 material check list物料检查表
trolley台车 carton纸箱 sub-line支线 left fork叉车 personnel resource department 人力资源部 production department生产部门 planning department企划部 QC Section品管科 stamping factory冲压厂 painting factory烤漆厂 molding factory成型厂 common equipment常用设备 uncoiler and straightener整平机 punching machine 冲床 robot机械手 hydraulic machine油压机 lathe车床 |刨床 planer |'plein miller铣床 grinder磨床 driller??床 linear cutting线切割 electrical sparkle电火花 welder电焊机 staker=reviting machine铆合机 position职务 president董事长 general manager总经理 special assistant manager特助 factory director厂长 department director部长 deputy manager | =vice manager副理 section supervisor课长 deputy section supervisor =vice section superisor副课长group leader/supervisor组长 line supervisor线长 assistant manager助理 to move, to carry, to handle搬运 be put in storage入库 pack packing包装 to apply oil擦油 to file burr 锉毛刺
机械类常用英语词汇大全丙烯丁二烯苯乙烯acrylonitrile-butadiene-stryrene (ABS) 主轴;心轴spindle 主题motif 令(纸张的计数单位) ream 凹座recess 凹模hollowing block 凸缘flange 凸缘联轴节flange coupling 凸轮cam 凸轮式配件cam-action fitting 凸轮传动cam drive 凸头螺丝raised head screw 加成作业;添加法addition process 加油oiling 加速器accelerator 功能;用途function 功率因子power factor 功率放大器power amplifier 功率板power amplifier board 功率晶体管power transistor 包氏记号法Bow's notation
「包浩思」;「包豪斯」〈设计风格) Bauhaus 半永固法;半永久接合semi-permanent joining 半接榫halving joint 半闭式槽榫stopped housing joint 半圆(木)锉half-round rasp 半圆车刀turning gouge 半圆锉half-round file 半圆头铆钉snap rivet 半导体semiconductor 卡路里;卡(热量单位) calorie 卡纸card paper 卡尺;测径器calipers 去角;倒角chamfer 可切削性machinability 可行性feasibility 可逆过程reversible process 可压缩性compressibility 可变电阻variable resistor 四分仪quadrant 四爪夹头four-jaw independent chuck 四圆心法(绘图) four-centre method 外卡尺outside calipers
机械英语词汇大全2 金属切削 metal cutting 机床 machine tool 金属工艺学 technology of metals 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 拉孔 broaching 装配 assembling 铸造 found 流体动力学 fluid dynamics 流体力学 fluid mechanics 加工 machining 液压 hydraulic pressure 切线 tangent 机电一体化 mechanotronics mechanical-electrical integration 气压 air pressure pneumatic pressure 稳定性 stability 介质 medium 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking 技术要求 technical
机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 剪切 shear 扭转 twist 弯曲应力 bending stress 强度 intensity 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve 失效 invalidation 强度 intensity 载荷 load 应力 stress 安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix 键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮
机械图纸英语翻译 以下是我在工作中常用的 ALL WELDS CONTINUOUS UNLESS OTHER WISE STATED. 未注焊缝均为连续焊 ALL WELDS 3mm FILLET UNLESS OTHER W ISE STATED 未注焊角高3mm. ALL UNSPECIFIED RA DI - R3 未注圆角R3 REMOVE A LL BURRS AND SHA RP EDGES 棱角倒钝 CHANNEL 槽钢 RSA 708 角钢70X70X8 M30X1.5 pitch M30X1.5的锥螺纹 Tackweld 点焊 OD 1/4" outside dimension 1/4"的缩写外径直1/4" 75 CRS 尺寸为75 材质为冷轧钢板 410 OPENING REF 410 开口参考尺寸 40 REF 尺寸为40,参考值 2.5" BSP 2.5” 圆锥管螺纹 2.5" BSPT HEXA GON 2.5” 六角圆锥管螺纹(即对丝) 30x2.5 FLAT BAR 30X2.5 扁钢 TYP 2 POSNS 2处 11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 总圈数约11圈;工作圈数约9圈;右旋;弹簧的端部磨平以便于接触.(此为弹簧技术说明) FEMALE: 内扣(母扣) MALE: 外扣(公扣) 偏心轴eccentric shaft 销轴PIN 开口销COTTER PIN 螺杆screw 紧定螺钉SET SCREW 圆螺母ROUND NUT 内六角螺钉SOCKET HEAD CAP SCREW 六角螺钉HEX HD SETSCREW 六角螺栓HEX HD BOL T 挡圈closing ring 弹性挡圈circlip 轴承隔套distance sleeve of axletree 轴承axletree 深沟球轴承DEEP GROOVE BA LL BEA RING 无扣长non-buckle longth 弹簧SPRING 吊环螺钉LIFTING EYE BOL T 开槽盘头螺钉SLOTTED PAN HEAD SCREW 圆锥滚子轴承TAPERED ROLLER BEA RING 推力球轴承THRUST BA LL BEARING