Linux-手工触发scsi扫描新添加的硬盘
Linux 手工触发scsi扫描新添加的硬盘
简单介绍一个方法,实现不重新启动linux而可以识别到新增的磁盘.环境描述:
OS: Redhat linux 5.4 x86(主机为vmware 虚拟主机)
增加一个50G的lun
一. 手工增加磁盘的命令
# echo "scsi add-single-device w x y z" > /proc/scsi/scsi
为使该命令正常运行，必须指定正确的参数值w、x、y 和z，如下所示：w 是主机适配器标识，第一个适配器为零(0)
x 是主机适配器上的SCSI 通道，第一个通道为零(0)
y 是设备的SCSI 标识
z 是LUN 号，第一个LUN 为零(0)
二. 执行命令前,检查/proc/scsi/scsi文件,确定新磁盘的id
Attached devices:
Host: scsi0 Channel: 00 Id: 00 Lun: 00
Vendor: VMware Model: Virtual disk Rev: 1.0
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 01 Lun: 00
Vendor: VMware Model: Virtual disk Rev: 1.0
Type: Direct-Access ANSI SCSI revision: 02
Host: scsi0 Channel: 00 Id: 02 Lun: 00
Vendor: VMware Model: Virtual disk Rev: 1.0 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 03 Lun: 00
Vendor: VMware Model: Virtual disk Rev: 1.0 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi0 Channel: 00 Id: 04 Lun: 00
Vendor: VMware Model: Virtual disk Rev: 1.0 Type: Direct-Access ANSI SCSI revision: 02
可以看到最大的id号为04,新增磁盘的ID应该确定为5.
三. 执行fdisk -l命令,检查当前磁盘的情况
[root@soadb scsi]# fdisk -l
Disk /dev/sda: 21.4 GB, 21474836480 bytes
255 heads, 63 sectors/track, 2610 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System
/dev/sda1 * 1 13 104391 83 Linux
/dev/sda2 14 2610 20860402+ 8e Linux LVM ......
Disk /dev/sde: 53.6 GB, 53687091200 bytes
255 heads, 63 sectors/track, 6527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sde doesn't contain a valid partition table
四. 执行命令
#echo "scsi add-single-device 0 0 5 0" >/proc/scsi/scsi
五. 执行fdisk命令,检查结果
[root@soadb scsi]# fdisk -l
......
Disk /dev/sde: 53.6 GB, 53687091200 bytes
255 heads, 63 sectors/track, 6527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sde doesn't contain a valid partition table
Disk /dev/sdf: 53.6 GB, 53687091200 bytes
255 heads, 63 sectors/track, 6527 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk /dev/sdf doesn't contain a valid partition table
可以看到,新增的50G的磁盘已经在操作系统中识别到,设备名称为/dev/sdf.此时就可以使用这个设备了.