搜档网
当前位置:搜档网 › 机械工程专业英语单词

机械工程专业英语单词

机械工程专业英语单词
机械工程专业英语单词

Lesson 1 Basic Concepts in Mechanics机械学的基本概念mechanics n.力学

modify v.修改,调解,变更manageable a.可控制【管理】的incline v.(使)倾斜

ramp n.斜板,斜坡【道】

slope v.(使)倾斜

friction n.摩擦

roll v.滚动

multiplier n.放大器,乘法器

broom n.扫帚

convert v.转变【化】

handle n.手柄【把】

sweep v.扫荡【描】,掠过efficiency n.效率gauge vt.测【计】量,校验bearing n.轴承

ideal mechanical advantage 理想的机械效益

neglect vt.忽略

Lesson 2 Basic Assumption in Plasticity Theory 塑性理论的基本假设

assumption n.假定

plasticity n.塑性

investigate v.调查,研究deformation n.变形

metal forming process 金属成型工艺【过程】

strain (rate) n.应变【速率】strength n.强度

stress n.应力

yield stress 屈服应力

flow stress 流动应力

tensile stress 拉【伸】应力compressive stress 压【缩】应力shear stress 剪【切】应力geometry n.几何形状

elastic a.弹性的

springback n.回弹

bending n.弯曲,折弯

precision forming 精密成型tolerance n.公差

continuum n.连续(体)metallurgical a.冶金(学)的

grain n.晶粒

dislocation n.位错

(uni-,tri-,multi-)axial a.(单,三,多)轴(向)的

anisotropy n.各向异性

cylindrical a.圆柱体的

cross-section n.横截面

platen n.(工作)台板,模板

coincide with 一致,相符

validity n.正确有效,合法

with ease 轻(而)易(举)的,很容易的

Lesson 3 Optimization for Finite Element Applications有限元优化的应用

optimization n.优化,优选(法)finite element 有限元

iterative a.反复的,迭代的alternative n.a.交替(的),可供选择的

manual a.手动的,人工的

trial-and-error 试凑法

bias vt,n.(使)偏向【重、差】

a desktop platform (计算机)桌面平台

constrain(t) v,n.强制,约束response n.反【响】应,灵敏度parameter n.参数

parametric a.参数的

preprocess vt.预(先)加工,预处理mesh n,v.网格,啮合

capability n.能力,性能,容量

loop n.环,回路,循环

pose v.提出

model n.模型,样品

displacement n.位移,排量,替换buckling n.弯【翘】曲,挠度

factor n.因素

gradient n.坡【梯】度,斜率

flur n.【电,磁,热,光】通量,流量multidisciplinary a.多学科的deflection n.偏移【转,离】,挠曲Lesson 4 Metals 金属

toughness n.韧性

corrosion n.腐蚀

dump v.倾倒,堆放

recyle v.反复【循环】利用

copper n.铜

aluminum n.铝

bronze n.青铜(器)

alloy n.合金

wear v.磨损

metallic a.(含)金属(制)的specification n.操作规程,技术要求,说明书

extract vt.提炼,萃取

iron n.铁

carbon n.碳

ferrous a.(含)铁的

ferrous metals 黑色金属

lead n.铅

zinc n.锌

tin n.锡

ore n.矿(石)

mineral n,a.矿物(的)

impurity n.杂质,不纯

Lesson 5 Metallic and Nonmetallic Materials金属和非金属材料magnesium n.镁

nickel n.镍

brass n.黄铜

luster n.光泽

ductility n.延展性,可锻性

it is likely that 很可能

it is certain to (inf.)必然,一定density n.密度

be distinguished from 与…区分coefficient n.系数

in connection with 关于,与…相关【结合】

category n.种类

hardness n.硬度

elasticity n.弹性

beam n.横梁,一束(光)

penetration n.贯穿,渗透

abrasion n.磨损【耗】

roll n,v.轧辊,滚,轧

mill n.轧钢机,铣床

spring n.弹簧

permanent a.永久的

rupture n.破【开】裂

stamp n.冲压

hammer n.(锻)锤

Lesson 6 Plastics and Other Materials塑料和其他材料

inorganic acid 无机酸

sulphuric acid 硫酸

hydrochloric acid 盐酸

solvent n.溶剂

carbon tetrachloride 四氯化碳rigid a,n.坚硬的,刚性(的),刚度mould(mold) n.模子,塑模,铸模decoration n.装饰

fabricate vt.制造【备】,生产injection molding 注射模塑(法)blow molding 吹塑(法)compression molding 压塑(法),模压(法)

extrusion n.挤压

vacuum forming 真空模塑(法)powder metallurgy 粉末冶金constituent n,a.组成【的,部分】,组元

simultaneously adv.同时subsequently adv.随后

coherent a.互相凝聚的,协调一致的

fusion n.熔化,熔接

crystalline n,a.结晶【的】,晶体【的】restriction n.限制【定】,节流

blend n,v.混合【物】,融合

press n,v.压力机,压制homogeneous a.均匀的

sinter n,vt.烧结【物】

Lesson 7 Die Life and Die Failure 模具的寿命和失效

die n.模具,锻【冲】模,凹模

die life 模具寿命

die failure 模具损坏

deterioration n.变坏,退化,损耗surface finish 表面光洁度breakdown n.破坏,击穿

lubrication n.润滑cracking n.裂纹

breakage n.断裂

mode n.方式,状态,模式

thermal fatigue 热疲劳

layer n.层

abrasive n,a.(研)磨料(的),磨损(的)

impression n.模膛,型腔(槽)

heat checking 热裂纹,龟裂

steep n,a.陡(坡)的,急剧的reversal n.颠倒,相反

overload n,v.(使)过【超】载initiation n.开【初】始,发【产】生discrete a.不连续的,单个的variable n.变量

cavity n.模膛,型槽

stock n.坯料,原材料

impact n,v.冲击,碰撞

Lesson 8 Cold Working and Hot Working 冷加工和热加工

cold[hot] working 冷热加工

forging n.锻造,锻件

classification n.分类recrystallization n.再结晶

take place 发生

strain [deformation] hardening 应变【变形】硬化

be referred to as 叫做,称为,被认为是

warm working 温加工,温锻

ultimate a,n.最终的,首要的,极限stress relieving 消除应力处理austenitic a.奥氏体的stainless steel 不锈钢

annealing n.退火

grain size 晶粒度

solid solution 固溶体

refinement n.精炼【制】,细化hazard n.危险,未知数,意外事件inherent a.固有的,先天的,本质的sensitive a.灵敏的,敏感的abnormal a.非正常的

critical strain 临界应变

Lesson 9 Casting 铸造

casting n.铸造【件】

die-casting n.模铸【件】

foundry n.铸造【车间】

pour v.浇注

suitability n.适应性

pig iron 生铁

cupola n.冲天炉,化铁炉

erosion n.腐蚀,(侵、烧)蚀

ladle n.铁水包

graphite n.石墨

solidify v.(使)凝固

disjoin v.拆散,分开

ingot n.(钢)锭

destructive a.破坏(性)的,有害的retard vt,n.(使)延缓,推迟

solvent n,a.溶剂(的)

copper-base alloy 铜基合金

Lesson 10 Metal Forming Processes in Manufacturing 制造中的金属成形工艺machine-building 机械制造

plastic working 塑性加工billet n 坯料,锻坯

blank n.坯料,(冲压)板坯configuration n.外形,配置,排布stroke n.行程,冲程

amortize v.阻尼,缓冲,分期偿还reliability n. 可靠性,安全性drawing n.(锻坯)拔长,【线,管材】拉拔

deep drawing 深冲(压)

brake forming 【压】折弯(机)成型stretch forming 张拉成型

military n,a.军队【事,人】(的)consumer goods 消费品

integrity n.完整性,完全(善)

jet engine 喷气发动机

turbine n.涡【汽】轮(机),透平(机)

regarding 考虑到,关于

Lesson 11 Forging锻造

armor n.铠甲

immortalize vt.(使)不朽(灭)blacksmith n.锻工

mechanical press 机械压力机hydranlic press 液压机

anvil n.(锤)砧,砧座

craftsman n.技工

handling n.处理,装卸,搬运flexibility n.柔(韧)性,灵活性drawn out 拔长

upset n.镦粗,顶锻

closed impression die 闭式模锻rapid-impact blow 快速冲击,猛打vertical a.立式的ram n.锤头,滑块,活动横梁

block n.(模)块

draft n.模锻斜度

symmetrical a.轴对称的

sizing n.整形,校正,定径

drop forging 落锻,锤模锻impression die forging 模锻

final forging 终锻

overheat n.过热

furnace n.【熔,高】炉

pyrometer n.高温计

Lesson 12 Benefits and Principles of Forging锻造的优点和工作原理metalworking n.金属压力加工

knead v.揉搓【制】

refine v.精炼【制】,细化

porosity n.多孔性,疏松

orient v.(使)定【取】向

flow line 流线

stress field 应力场

manual skill 手工技巧

at one’s command 自由使用,支配soundness n.致密性,坚固性,无缺陷attainable a.可达【得】到的

open die forging 自由锻

gross n.总共,重大

confine vt. 限制,约束

convert v.转变【换】,更换

broken up 破【断】裂,分散microshrinkage n.显微缩孔elimination n.消除,淘汰

align v.调整,对中,校直Lesson 13 Welding焊接

weld(ing) v,n.焊接,熔焊pressurewelding 压力焊

spotwelding 点焊

buttwelding 对头(缝)焊fusionwelding 熔焊,熔接

fiux-shielded arc welding 熔剂保护电弧焊

diversity n.不同多样性

fasten(ing) v,n.连接(件),紧固(件)shielding n.遮护,屏蔽

solder(ing) v,n.软钎焊,(低温)焊料bismuth n.铋

cadmium n.镉

rivet n,v. 铆钉,铆接

braze n,vt.硬钎焊,铜焊

oxidation n.氧化

flux n.焊接,助溶剂

squeeze v.挤压

oxy-acetylene n,a.氧(乙)炔(的)torch n.焊炬

electrode n.电(焊)极,焊条

filler n.填充(剂)

overlap v.搭接,重叠

strike v.攻【打】击,放电

Lesson 14 Heat Treatment热处理heat treatment 热处理microstructure n.显微组织

low-carbon steel 低碳钢

prescribe v.规定,指示

microscopic a.显微的,微观的spheroidizing n.球化(处理)normalizing n.正火,(正)常化annealing n.退火

hardening n.淬火

tempering n.回火

soaking(=holding) n.均热,保温retarding media 延缓介质

prolonged a.长时间的,持续很久的critical temperature 临界温度globular a.球形(状)的

carbide n.碳化物,硬质合金quenching n.淬火,骤冷

removal n.除去,放出

Lesson 15 Introduction to Mechanism 机构介绍

mechanism n.机械,机构,机构学kinematic a.=kinematical 运动的,运

动学的

kinematic chain 运动链

link n.构件,杆件. v.连接【结】definite a.确定的

constrained a.约束的,限定的unconstrained a.无约束的

linkage n.连杆(组,机构)

joint n.结【接】台,铰链. a.连接的,联合的

pin n.销【钉】,铰销

revolution v.旋转,转动. n.回转体prismatic a.棱柱(形)的

nonlinear a.非线性的

four-bar linkage 四杆机构

kinematic chain 运动链

prime mover 原动者【机】,驱动件coupler n.连接件,连杆

pivot n.枢(轴),轴销,回转副,旋转中心

configuration n.外形,构造,结构inversion n.转换,更换

slider-crank mechanism 曲柄滑块机构multiloop n.多环链,a.多回路的sketch n.草【简,示意】图,v.画草图,草拟

skeleton diagram 草图,示意图,简图envision v.想象

binary a.二【双,复】的,二元的ternary a.三元的

ternary links 三杆组

quaternary a.四元的

quaternary links 四杆组

cam 凸轮

cam follower n.凸轮从动件

gear n.齿轮

sprocket n.链轮

belt n.【皮,布,钢】带

pulley n.带轮

spherical a.球的,球面的

helical a.螺旋的

three-dimensional 三维的,空间的intuitively adv.直觉【观】地synthesis n.合成(法),综合kinematician n.运动学研究者(家)innate a.先天的,固有的

Lesson 16 Movement Analysis 运动分析

criterion(pl.criteria) n.(判断)标准,判据,准则

branch n,v.分(部,支)transmission angle 传动角

rock n.摆动, v.摇动

oscillate v.摆动,摇动parallelogram n.平行四边形antiparallelogram n.反平行四边形frame n.机架,构架

impart v.给予,分给

to impart M to N 把M给N

torque n.力矩,扭矩

dynamic a.=dynamical 动力的,动力学的

inertia n.惯性(物),惯量

static a.=statical 静力【学】的,静的

index n.指数,指标

friction n.摩擦

thumb n.拇指,v.用拇指翻

rule of thumb 根据经验和实际所得的做法

matrix n.矩阵

determinant n.行列式

derivative n.导数

derivative of M with respect to N M 对于N的导数

movability n.可动性,易动性parameter n.参数

discount v.打折扣,忽视

absolute a.绝对的

graphical a.图形的,图解的

polygon n.多边形theorem n.定理

stress n.应力

bearing n.轴承

centripetal a.向心的

Lesson 17 Kinematic Synthesis运动的综合

packaging machinery 包装机械lubrication n.润滑

specification n.技术要求

actuation n.驱动

jerk n.震动,冲击

axis n.(pl.axes)轴【线,心】,中心线contour n.外形,轮廓线

eccentricity n.偏心【度,率】

gear ration 齿轮【速,齿数】比topologically adv.拓扑学地

customary a.通常的,习惯的correlate v.使相关,使发生关系analog n.=analogue 类似(物),模拟linear analog 线性模拟

second acceleration 二阶加速度higher acceleration 高阶加速度paraphrase v.释义,意译

describe v.叙述,描述,作…运动category n.种类,类别

deliberation n.慎重考虑

province n.省,领域

preconceive v.预想,事先想好analog computer 模拟计算机

trace v.追踪,描画

timing n.定时,计时,配时

pitch v.投掷trajectory n.轨迹

embed v.嵌入,夹在层间

orientation n.(定)方位,(取)方向scoop n.勺子,铲斗, v.挖,掘,铲Lesson 18 Cams and Gears凸轮和齿轮cam n.凸轮

gear n.齿轮

curve n.曲线 a.弯曲的

groove n.槽,沟

mate v.配合,啮合

cylindrical a.圆柱的

two-dimensional or planer 两维的或平面的

three-dimensional or spatial 三维的或空间的

normal n.法线 a.垂直的

complement n,a.余角,余的

collinear a.共线的

lateral a.横向的,侧向的

stem n.杆

guide n.导向件【器,装置】,导槽(座)intermittent a.间断的,不连续的dwell n,v.停止,小停顿

inertial a.惯性的,惯量的

engage v.啮合

rack n.齿条

noncircular a.非圆的

conjugate a.共轭的,n.共轭值(线)cycloidal a.摆线的

involved a.渐开线的, n.渐开线tolerance n.间隙,公差

spur gear 直齿圆柱轮radial a.径向的,沿半径的

offset n,vt.偏移,偏心 a.偏心的disk cam 盘形凸轮

tangent n.切线 a.相切的,切线的concentric a.同圆(的),同心(的)camshaft n.凸轮轴

pitch curve 节线

herringbone a.人字形的

intersect v.横穿,相交

parallel helical gear斜齿轮,

平行轴螺旋齿轮

crossed helical gear 交错轴螺旋齿轮face gear 端面齿轮

spiral bevel gear 螺旋齿圆锥齿轮worm n.蜗杆

skew bevel 斜齿圆锥齿轮

hypoid gear 准双曲面(直角交错轴双曲面)齿轮

addendum (pl.addenda) n.齿顶,齿顶高

project v.伸出,突出

clearance n.间隙

dedendum (pl. dedenda)n.齿根,齿根高

tooth space 齿间距

backlash n.间隙,齿隙

Lesson 19 Screws, fasteners and joints螺纹件、紧固件和联接件

screw n.螺钉,螺丝, v.旋紧,攻丝fastener n.紧固件

joint n.连【联】接,接合

bolt n.螺栓

nut n.螺母cap screw 有头螺钉

setscrew n.定位【固定,调整】螺钉rivet n.铆钉, v.用铆钉铆接

key n.键

weld n,v.焊接,熔焊

braze n,v.钎焊,铜焊

clip n.夹子, v.夹住,夹紧synonymous a.同意义的

monotonous a.单调的

taint n.污点,污染 v.弄脏

tough a.坚韧的

ductile a.可延伸的,有延展性的,韧性的

tighten v.上紧,拉紧

twist v.扭转

jumbo n.大型喷气式客机

titanium n.钛

close-tolerance 高精密度的

tooling n.工具,刀具 v.用刀具(切削)加工

proliferate v.增殖,增殖

assembly n.安装,装配,组件

tap n.丝锥, v.攻螺丝

stud n.双头螺栓

resemble v.类似,像

thread n.螺纹(线),v.车螺纹

drill n,v.钻孔

hexagon head 六角头

fillister n.凹槽

flat head 平头

hexagon socket head 六角沉头disassemble v.拆开tensile a.拉【张】力的,受拉的shear n.剪切【力】 v.剪切【断】harden v.使硬【化】

washer n.垫圈

preload n.预载荷

fatigue n.疲劳

micrometer n.千分尺,千分表elongation n.拉【伸】长

modulus n.(pl.moduli)模数,模量wrench n.扳手

dial n.刻度盘

fractional a.分数的,小数的

Lesson 21 Helical, Worm and Bevel Gears斜齿轮、蜗杆蜗轮和锥齿轮helical gear 斜齿轮

worm n.蜗杆,螺杆

bevel gear 圆锥齿轮

helix n,a.(pl. helices 或 helixes)螺旋线,螺旋线的

right hand 右手,右旋的

helicoid n.a.螺旋【面,体】,螺旋(状,纹)的

wrap v.缠绕

unwind v.解开,展开

generate v.产生,展成(加工)engagement n.啮合,接触

diagonal n,a.对角线(的)objectionable a.该反对的,不能采用的

spiral n,a. 螺旋线(的),卷线(的)spiral gear 螺旋齿轮

mesh n.啮合

worm gear 蜗轮pinion n.小齿轮

pitch cylinder 节圆柱

concave a.中凹的

curvature a.曲率

screw-like 像螺丝(杆)的

thread n.线状物,螺纹线

envelop v.包围,封闭

enclose v.包围

lead angle 导角

cast v.铸造

mill v.铣削

outboard a,ad.外侧的,向外pronounced a.明确的,显着的

stress n.应力

tapered a.锥形的

positively ad.确定地,强制(传动)

Pitch-line velocity 节线速度automobile differential 汽车差速器gearing n.齿轮传动(装置)

offset n.偏置,横距

hypoid a.准双曲面的

hyperboloid n.双曲面,双曲面体Lesson 22 Shafts, Clutches and Brakes轴、离合器和制动器

shaft n.轴

clutch n.离合器

brake n.制动器

pulley n.(皮,胶)带轮

flywheel n.飞轮

sprocket n.链轮,星轮

bending moment 弯曲力矩torsional a.扭转的

static a.静(力,态)的

axle n.心轴,轮轴

spindle n.心轴,主轴deflection n.偏移,弯曲

fillet n.圆角,倒角

peening n.喷射(加工硬化法)shot peening 喷丸硬化

stiff a.刚性的

inertia n.惯性,惯量slippage n.滑动

actuation n.驱动,开动coefficient n.系数

statics n.静力学

rim n.边缘,轮缘

shoe n.闸瓦,制动片【块】

相关主题