三层交换机 配置代码

DCRS-5526S>y
> Unrecognized command or illegal parameter!
DCRS-5526S>00:34:52: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0
/15,changed state to DOWN
00:34:54: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/15,changed
state to UP
00:35:02: %DUPLEX-7-CHANGE: Interface Ethernet0/0/15, DUPLEX changed state to HA
LF
00:35:04: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/15,changed
state to DOWN
00:35:22: %LINEPROTO-5-UPDOWN: Line protocol on Interface Ethernet0/0/15,changed
state to UP
00:35:22: %DUPLEX-7-CHANGE: Interface Ethernet0/0/15, DUPLEX changed state to FU
LL

DCRS-5526S>
DCRS-5526S>ena
DCRS-5526S#conf
DCRS-5526S(Config)#vlan 10
DCRS-5526S(Config-Vlan10)#switchport interface e0/0/1-5
Set the port Ethernet0/0/1 access vlan 10 successfully
Set the port Ethernet0/0/2 access vlan 10 successfully
Set the port Ethernet0/0/3 access vlan 10 successfully
Set the port Ethernet0/0/4 access vlan 10 successfully
Set the port Ethernet0/0/5 access vlan 10 successfully
DCRS-5526S(Config-Vlan10)#vlan 20
DCRS-5526S(Config-Vlan20)#switchport interface e0/0/6-10
Set the port Ethernet0/0/6 access vlan 20 successfully
Set the port Ethernet0/0/7 access vlan 20 successfully
Set the port Ethernet0/0/8 access vlan 20 successfully
Set the port Ethernet0/0/9 access vlan 20 successfully
Set the port Ethernet0/0/10 access vlan 20 successfully
DCRS-5526S(Config-Vlan20)#vlan 30
DCRS-5526S(Config-Vlan30)#switchport inter e0/0/11-15
Set the port Ethernet0/0/11 access vlan 30 successfully
Set the port Ethernet0/0/12 access vlan 30 successfully
Set the port Ethernet0/0/13 access vlan 30 successfully
Set the port Ethernet0/0/14 access vlan 30 successfully
Set the port Ethernet0/0/15 access vlan 30 successfully
DCRS-5526S(Config-Vlan30)#vlan 40
DCRS-5526S(Config-Vlan40)#switchport interface e0/0/24
Set the port Ethernet0/0/24 access vlan 40 successfully
DCRS-5526S(Config-Vlan40)#exit
DCRS-5526S(Config)#inter vlan 10
00:50:27: %LINK-5-CHANGED: Interface Vlan10, changed state to UP
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan10,changed state to UP
DCRS-5526S(Config-If-Vlan10)#ip add 172.17.1.1 255.255.255.0
DCRS-5526S(Config-If-Vlan10)#no shut
DCRS-5526S(Config-If-Vlan10)#vlan 20
DCRS-5526S(Config-Vlan20)#inter vlan 20
00:53:03: %LINK-5-CHANGED: Interface Vlan20, changed state to UP
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan20,changed state to UP
DCRS-5526S(Config-If-Vlan20)#ip add 172.17.2.1 255.255.255.0
DCRS-5526S(Config-If-Vlan20)#no shut
DCRS-5526S(Config-If-Vlan20)#inter vlan 30
00:54:41: %LINK-5-CHANGED: Interface Vlan30, changed state to UP
%LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan30,changed state to UP
DCRS-5526S(Config-If-Vlan30)#ip add 172.17.3.1 255.255.255.0
DCRS-5526S(Config-If-Vlan30)#no shut
DCRS-5526S(Config-If-Vlan30)#inter vlan 40
00:55:21: %LINK-5-CHANGED: Int

erface Vlan40, changed state to UP
%LINEPROTO-5-UPDOWN: Line pr
otocol on Interface Vlan40,changed state to UP
DCRS-5526S(Config-If-Vlan40)#ip add 172.17.4.1 255.255.255.0
DCRS-5526S(Config-If-Vlan40)#

Press ENTER to get started

DCRS-5526S>ena
DCRS-5526S>conf
> Unrecognized command or illegal parameter!
DCRS-5526S>enab
DCRS-5526S#conf
DCRS-5526S(Config)#router rip
DCRS-5526S(Config-Router-Rip)#ver 2
DCRS-5526S(Config-Router-Rip)#exit
DCRS-5526S(Config)#inter vlan 10
DCRS-5526S(Config-If-Vlan10)#ip rip work
DCRS-5526S(Config-If-Vlan10)#inter vlan 20
DCRS-5526S(Config-If-Vlan20)#ip rip work
DCRS-5526S(Config-If-Vlan20)#inter vlan 30
DCRS-5526S(Config-If-Vlan30)#ip rip work
DCRS-5526S(Config-If-Vlan30)#inter vlan 40
DCRS-5526S(Config-If-Vlan40)#ip rip work