车辆工程专业英语译文

1.2 发动机

发动机作为动力装置。最常见的内燃机通过燃烧发动机气缸里的液体燃料而获得能量。内燃机有两种类型：汽油机（又称为点燃式发动机）和柴油机（又称为压燃式发动机）。两种类型均称为热力发动机。燃烧燃料产生的热量使汽缸里气体的气压增加并提供能量通过传动轴连接到传动系统。

发动机气缸的排列方式称为发动机配置。直列式发动机的汽缸呈一列布置。这个设计创造了一个简单的发动机缸体铸造。在车辆应用中，汽缸数一般是2-6缸，汽缸中心线与水平面垂直。当汽缸数增多时，发动机尺寸和曲轴就成为一个问题。解决这个问题的办法就是采用V形（汽缸呈两列布置，且两列气缸之间夹角为V形）发动机。这个设计使发动机尺寸和曲轴都变得更短且更坚硬。

前置发动机纵向安装，既可前轮驱动也可后轮驱动。后置发动机是将发动机安装在后轮后面。发动机可横置或纵置，一般情况下为后轮驱动

1.3.3 悬架系统的功能是隔离、缓减路面冲击和振动,避免传递到车身,影响乘客和货物的舒适性和安全性另外不论路面如何悬架系统都应保持轮胎和路面的接触

1.3.4

鼓式制动器有鼓附在轮毂、制动时的制动蹄通过扩大里面的鼓来制动。在盘式制动器上连着轮毂的制动器被紧紧夹在两个制动块之间，所有汽车都必须配备两套独立的制动系统，即行车制动和紧急制动。

2.2.2 气缸套

气缸套用于发动机缸体提供活塞和活塞环的耐磨材料。那块可由一种铁，易于铸造而作出的套筒使用另一种就是能够更好地起到磨损作用，还有两种主要类型的套筒：干，湿（图

2 - 5 ）。干套可以被抛弃，或压成一个新的块或用于严重磨损或损坏而无法轻易被钢瓶翻新得的套筒。这是一个在其在缸体孔压适合。它的墙壁是两毫米厚。它的外表面，是符合其全长块接触。它与顶块冲洗和面漆难以看到。一旦到位，干袖子成为缸体的永久部分。用湿的套筒。外表面是周围的汽缸水套的一部分。这就是所谓湿缸，因为它有对其外表面的冷却液。这有助于加快热套和冷却水之间的转移。套筒顶部密封，以防止冷却液泄漏

2.3.2活塞总成

活塞是四个运动周期中一个重要部分,很多活塞都是从铝中提炼出来研制而成的.活塞,通过连杆传递能量来压缩点燃混合气体. 这些能力转化为曲柄的动能.这样,圆形的钢圈装入汽缸,用活塞环来密封整个燃烧室.这个称为活塞环。这些用来放活塞环的称为凹槽。一个活塞销放在中间通过一个小孔固定。活塞销的作用是固定活塞于连杆之间的连接，对活塞销起作用的是活塞销凸台。

活塞本身,它的环和活塞销一起称为活塞总成

2.3.6飞轮

飞轮有碳钢制成，装在曲轴的后端。同时带动曲轴旋转和离合器。同时传送给变速器，和启动齿圈包围着在四个冲程当中只有一个冲程是做功的所以飞轮只有在这个时间带动曲轴，发动机在这几个不做功的冲程转动

1。燃油泵

大多数车今天使用一个机械式燃油泵。这种燃料泵出了汽油，并通过油管向化油器或喷射系统。在大多数汽车，泵安装在发动机缸体。有些汽车电动燃油泵有一个。该泵安装在皮卡与燃料和燃料轨，发送单元油箱。

对机械燃油泵操作取决于对凸轮轴叶。作者：爱在旋转移动泵摇臂。泵内，可以灵活的隔膜通过膜片弹簧摇臂，拉杆和链接。如图所示，燃油泵也有一个入口和燃料出口。

由于凸轮轴上的旋转叶，横膈膜上下移动内部的引擎。隔膜的吸向下运动从进入泵油箱。隔膜向上运动推到了化油器，从泵的燃料。2。化油器

化油器提供燃料比例的空气量流经喉管。当你在加速器踏板时，扩大开放节流阀吸引更多的空气通过化油器。化油器提供这取决于许多因素更丰富或更精简的混合物：发动机转速，负荷，温度，节气门位置。为了满足复杂的要求，一化油器是一个非常复杂的设备与许多内部通道及零部件.

３.２.１dry friction clutch

当汽车原地起步时，离合器要将静止的变速器轴同发动机接合起来，此时发动机必须高速旋转以提供足够大的功率，否则载荷过大将引起发动机熄火。

To start the engine,

为了起动发动机，驾驶员必须踩下离合器踏板，使变速器与发动机分离．为了使汽车运行，驾驶员必须使发动机和变速器重新结合．这些部件必须渐进的结合在一起．

3.3.

4.2 Planetary Gears

行星齿轮齿轮系改变自动变速器的传动比。然而，在自动变速箱的齿轮系是不同于在手动变速箱齿轮的系。自动变速箱有一套行星齿轮系统而不是一个副轴和齿轮。行星齿轮实际上是由一组通过行星架组合在一起的齿轮。行星架上有销穿过每个行星轮的中心。当行星架运动时，所有的行星轮也随之运动。当行星架固定时，行星轮绕销转动。//行星齿轮机构是一组齿轮，由行星架将这些齿轮组合在一起。行星架上有销穿过每个行星轮的中心。当行星架运动时，所有的行星轮也随之运动。当行星架固定时，行星轮绕销转动

汽车专业英语翻译综合

第一章汽车总论 1)Today’s average car contains more than 15,000 separate, individual parts that must work together. These parts can be grouped into four major categories: body, engine, chassis and electrical equipment 。P1 现在的车辆一般都由15000多个分散、独立且相互配合的零部件组成。这些零部件主要分为四类：车身、发动机、底盘和电气设备。 2)The engine acts as the power unit. The internal combustion engine is most common: this obtains its power by burning a liquid fuel inside the engine cylinder. There are two types of engine: gasoline (also called a spark-ignition engine) and diesel (also called a compression-ignition engine). Both engines are called heat engines; the burning fuel generates heat which causes the gas inside the cylinder to increase its pressure and supply power to rotate a shaft connected to the power train. P3 发动机作为动力设备，常见的类型是内燃机，其原理是通过发动机缸内的液体燃料燃烧而产生能量。发动机可分为两类：汽油机（点燃式）和柴油机（压燃式），都属于热力发动机。燃料燃烧产生热量使缸内气压上升，产生的能量驱动轴旋转，并传递给动力传动系。 第二章内燃机 1)Power train system: conveys the drive to the wheels 2)Steering system: controls the direction of movement 3)Suspension system: absorbs the road shocks 4)Braking system: slows down the vehicle P4 传动系把发动机输出的扭矩传递给驱动轮。传动系包括离合器（对应机械变速器）或液力变矩器（对应液力自动变速器）、变速器、驱动轴、主减速器、差速器和驱动桥。 5)Drum brakes have a drum attached to the wheel hub, and braking occurs by means of brake shoes expanding against the inside of the drum. With disc brakes, a disc attached to the wheel hub is clenched between two brake pads. P6 鼓式制动器的制动鼓和轮毂连接，制动蹄张开压紧制动鼓内侧从而产生制动。在盘式制动器上，连着轮毂的制动盘被紧紧夹在两个制动块之间。 1)Linking the piston by a connecting rod to a crankshaft causes the gas to rotate the shaft through half a turn.The power stroke"uses up"the gas,so means must be provided to expel the burnt gas and recharge the cylinder with a fresh petrol-air mixture:this control of gas movement is the duty of the valves;An inlet valve allows the mixture to enter at the right time and an exhaust valve lets out the burnt gas after the gas has done its job . P10 活塞通过连杆和曲轴连接，使得气体带动曲轴旋转半圈。作功冲程耗尽了所有的气体，这样就必须采取相应的措施排出废气并且向气缸内充入新的可燃混合气：气体的运动由气门来控制。进气门使可燃混合气在恰当的时刻进入气缸，排气门使燃烧后的废气排出气缸。 2)The spark-ignition engine is an internal-combustion engine with externally supplied in ignition,which converts the energy cntained in the fuel to kinetic energy.The cycle of operations is spread over four piston strokes. To complete the full cycle it takes two revolutions of the crankshaft. P11 火花点火式发动机是由外部提供点火的内燃机，从而将含在燃料内的能量转化成动能。发动机的一个工作循环分布在活塞的四个行程中，一个完整的工作循环曲轴需要转动两圈。 3)The oil pump in the lubricating system draws oil from the oil pan and sends it to all working parts in the engine. The oil drains off and runs down into the pan. Thus,there is constant circulation of oil between the pan and the working parts of the engine. P15

各专业的英文翻译剖析

哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学（含税收学）Public Finance (including Taxation) 金融学（含保险学）Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law 法学Science of Law 法学理论Jurisprudence 法律史Legal History 宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence 民商法学(含劳动法学、社会保障法学) Civil Law and Commercial Law (including Science of Labour Law and Science of Social Security Law ) 诉讼法学Science of Procedure Laws

车辆工程汽车离合器的外文文献翻译

经典文档下载后可编辑复制 湖北文理学院 毕业设计(论文)英文翻译 题目有限元热分析的陶瓷离合器 专业车辆工程 班级Xxx 姓名Xxxx 学号2010138xx 指导教师 职称Xxx 副教授 2014年2月25日

Fethermal analysis of a ceramic clutch 1. Introduction Abrasive dry running vehicle clutches are force closure couplings. Torque and speed transmission are ensured by the frictional force generated between two pressed surfaces. Reasons for the application of ceramic as a friction medium include good heat and wear resistance properties, which provide the opportunity to drive higher pressures, and a low density. Thus, an increasing power density is enabled with a parallel minimization of construction space. Measurements with a first prototype of a clutch disk using ceramic facings were performed at Karlsruhe University in a laboratory specialized in passenger car drive system testing. In the course of analysis the finite element (FE) model was to be constructed with the knowledge of measurement data and measurement conditions. Calculations were intended to determine the temperature distribution of the clutch disk and its environment at each moment in time corresponding to measurements. It is essential to be familiar with the temperature range in order to examine the wear characteristics of the system. Thus, important information is derived from measurement data. In critical load cases, the highest expected temperatures must be forecast in space and time in order to protect measuring instruments close to the location of heat generation. The goal of this study is to analyze and modify the clutch system to provide better operating conditions by improving the heat conduction and convection of the system or to increase the amount of the energy converted into frictional heat. Furthermore, it is desired to find better design solutions for more efficient clutch systems. Calculations were performed by the Cosmos Design Star software. During model development, great care had to be taken for proper simplification of geometry, the selection of element sizes, and the correct adjustment of time steps due to the substantial hardware requirements for transient calculations. Changes in thermal parameters such as the surface heat convection coefficient and thermal load had to be taken into consideration on an on-going basis in terms of time and location. The two sides of the analyzed test clutch system can only be managed by two independent models linked by heat partition,

汽车专业英语翻译

About car engine Of all automobile components,an automobile engie is the most complicated assembly with dominant effects on the function of an autombile.So, the engine is generally called the"heat"of an automobile. 在汽车的所有部件中，汽车发动机是最复杂的组件，其对整车性能有着决定性的作用。因而发动机往往被称作发动机的“心脏”。 There are actually various types of engines such as electric motors,stream engines,andinternal combustion engines.The internal combustion engines seem to have almost complete dominance of the automotive field.The internal combustion engine,as its name indicates,burns fuel within the cylinders and converts the expanding force of the combustion into rotary force used to propel the vehicle. 事实上，按动力来源分发动机有很多种，如电动机、蒸汽机、外燃机等。然而内燃机似乎在发动机领域有着绝对的统治地位。就像其字面意思一样，内燃机的染料在气缸内燃烧，通过将燃烧产生气体的膨胀力转换成转动力来驱动发动机前进。 Engine is the power source of the automobile.Power is produced by the linear motion of a piston in a cylinder.However,this linear motion must be changed into rotary motion to turn the wheels of cars or trucks.The puston attached to the top of a connecting rod by a pin,called a piston pin or wrist pin.The bottom of the connecting rod is attached to the crankshaft.The connecting rod transmits the up-and-down motion of the piston to the crankshaft,which changes it into rotary motion.The connecting rod is mounted on the crankshaft with large bearings called rod bearing.Similar bearings, called main bearings,are used to mount the crankshaft in the block. 发动机是整部车的动力来源。能量来自于活塞在气缸内的（往复）直线运动。然而这种（往复）直线运动必须要转换成旋转运动才能驱动车轮。活塞与连杆通过一个销来连接，这个销称为活塞销。连杆的下部连接于曲拐。连杆把活塞的上下往复运动传递给曲拐，从而将往复直线运动转变成旋转运动。连杆和曲拐的连接使用大的轴承，称之为连杆轴承，类似的轴承也用于将曲轴连接到机体，称之为主轴承。 They are generally two different types of cooling system:water-cooling system and air-cooling system.Water-cooling system is more common.The cooling medium, or coolant, in them is either water or some low-freezing liquid, called antifreeze.A water-cooling system consists of the engine water jacket, thermostat, water pump, radiator, radiator cap, fan, fan drive belt and neccessary hoses. 主要有两种类型的冷却系统：水冷和风冷。水冷系统更为普遍。系统所用冷却介质或是冷却液常委水或其他低凝固点液体，称为抗凝剂。一个完整的水冷系统包括机体水套，节温器，水泵，散热器，散热器罩，风扇，风扇驱动皮带和必需的水管。 A water-cooling system means that water is used as a cooling agent to circulate through the engine to absorb the heat and carry it to the radiator for disposal.The ebgine is cooled mainly through heat transfer and heat dissipation.The heat generated by the mixture burned in the engine must be transferred from the iron or aluminum cylinder to the waterin the water jacket.The outside of the water jacket dissipates some of the heat to the air surrounding it, but most of the heat is carried by the cooling water to the radiator for dissipation.When the coolant temperature in the system reaches 90°,the termostat valve open fully, its slanted edge shutting off

汽车制动系统(机械、车辆工程毕业论文英文文献及翻译)

Automobile Brake System汽车制动系统 The braking system is the most important system in cars. If the brakes fail, the result can be disastrous. Brakes are actually energy conversion devices, which convert the kinetic energy (momentum) of the vehicle into thermal energy (heat).When stepping on the brakes, the driver commands a stopping force ten times as powerful as the force that puts the car in motion. The braking system can exert thousands of pounds of pressure on each of the four brakes. Two complete independent braking systems are used on the car. They are the service brake and the parking brake. The service brake acts to slow, stop, or hold the vehicle during normal driving. They are foot-operated by the driver depressing and releasing the brake pedal. The primary purpose of the brake is to hold the vehicle stationary while it is unattended. The parking brake is mechanically operated by when a separate parking brake foot pedal or hand lever is set. The brake system is composed of the following basic components: the “master cylinder” which is located under the hood, and is directly connected to the brake pedal, converts driver foot’s mechanical pressure into hydraulic pressure. Steel “brake lines” and flexible “brake hoses” connect the master cylinder to the “slave cylinders” located at each wheel. Brake fluid, specially designed to work in extreme conditions, fills the system. “Shoes” and “pads” are pushed by the slave cylinders to contact the “drums” and “rotors” thus causing drag, which (hopefully) slows the c ar. The typical brake system consists of disk brakes in front and either disk or drum brakes in the rear connected by a system of tubes and hoses that link the brake at each wheel to the master cylinder (Figure). Basically, all car brakes are friction brakes. When the driver applies the brake, the control device forces brake shoes, or pads, against the rotating brake drum or disks at wheel. Friction between the shoes or pads and the drums or disks then slows or stops the wheel so that the car is braked.

汽车专业英语_单词表

unit1 body 车身chassis 底盘enclosure外壳、套hood车棚、车顶sway 摇摆frame车架steering转向、操作brake 制动weld焊接rivet铆钉bolt螺钉washer垫圈vibration 振动stabilizer稳定器ride乘坐舒适性handling操作稳定性linkages转向传动机构plier钳子distributor分电器alternator交流发电机regulator调节器carburetor化油器radiator散热器、水箱defroster除冰装置sludge金属碎屑transmission变速器differential 差速器power train 传动系unitized body 承载式车身suspension system 悬架系统steering system 转向系braking system 制动系shock absorbers减震器control arms控制臂steering wheel 转向盘steering column转向管柱steering gears 转向器tie rod 横拉杆idler arm随动臂brake shoe制动蹄disc brake 盘式制动器drum brakes 鼓式制动器ignition system 点火系统exhaust system 排气系统lubrication system 润滑系oil filters 机油滤清器drive（or propeller）shaft传动轴universal joints 万向节dynamo发电机horn喇叭swived 旋转steering box转向器timing gear 正时齿轮bevel gear 锥齿轮mesh with与啮合leaf spring 钢板弹簧stub axle 转向节 unit2 longitudinal纵向的transverse横向的reciprocate往复spin旋转piston活塞ignite点火rub摩擦quart夸脱reservoir油箱mechanical机械的enclosed被附上的gallon加仑stroke冲程camshaft凸轮轴combustion燃烧disengaged脱离啮合的flywheel飞轮internal-combustion engine内燃机diesel-fuel柴油LPG=Liquefied Petroleum Gas液化石油气体CNG=Compressed natural gas压缩天然气spark ignition火花点火compression ignition压缩点火spark plug火花塞gas-turbine engine蒸汽机Stirling engine斯特灵发动机lubricating system润滑系统oil pan油底壳oil pump机油泵exhaust system排气系统emission-control system排放控制系统energy conversion能量转换air/fuel ratio空燃比connecting rod连杆TDC=Top Dead Center上止点BDC=Bottom Dead Center 下止点intake stroke进气冲程compression stroke压缩冲程power stroke作功冲程exhaust stroke排气冲程compression ratio压缩比lifter挺柱rocker摇臂retainer弹簧座seal密封件tappet 推杆lobe凸起gasket垫圈valve train配气机构cam follower气门挺柱rocker arm摇臂combustion chamber燃烧室intake valve进气阀exhaust valve排气阀valve stem气门杆valve cover气门室盖valve port阀口valve guide气门导管 unit3

各专业的英文翻译

中国教育在线考研频道提供考研全方面信息指导及咨询服务，为您成功考研提供一切帮助。 哲学Philosophy 马克思主义哲学Philosophy of Marxism 中国哲学Chinese Philosophy 外国哲学Foreign Philosophies 逻辑学Logic 伦理学Ethics 美学Aesthetics 宗教学Science of Religion 科学技术哲学Philosophy of Science and Technology 经济学Economics 理论经济学Theoretical Economics 政治经济学Political Economy 经济思想史History of Economic Thought 经济史History of Economic 西方经济学Western Economics 世界经济World Economics 人口、资源与环境经济学Population, Resources and Environmental Economics 应用经济学Applied Economics 国民经济学National Economics 区域经济学Regional Economics 财政学（含税收学）Public Finance (including Taxation) 金融学（含保险学）Finance (including Insurance) 产业经济学Industrial Economics 国际贸易学International Trade 劳动经济学Labor Economics 统计学Statistics 数量经济学Quantitative Economics 中文学科、专业名称英文学科、专业名称 国防经济学National Defense Economics 法学Law 法学Science of Law 法学理论Jurisprudence 法律史Legal History 宪法学与行政法学Constitutional Law and Administrative Law 刑法学Criminal Jurisprudence

2019年车辆工程专业毕业论文_外文翻译1.doc

Drive force control of a parallel-series hybrid system Abstract Since each component of a hybrid system has its own limit of performance, the vehicle power depends on the weakest component. So it is necessary to design the balance of the components. The vehicle must be controlled to operate within the performance range of all the components. We designed the specifications of each component backward from the required drive force. In this paper we describe a control method for the motor torque to avoid damage to the battery, when the battery is at a low state of charge. Society of Automotive Engineers of Japan, Inc. and Elsevier Science B.V. All rights reserved. 1. Introduction In recent years, vehicles with internal combustion engines have increasingly played an important role as a means of transportation, and are contributing much to the development of society. However, vehicle emissions contribute to air pollution and possibly even global warming, which require effective countermeasures. Various developments are being made to reduce these emissions, but no further large improvements can be expected from merely improving the current engines and transmissions. Thus, great expectations are being placed on the development of electric, hybrid and natural gas-driven vehicles. Judging from currently applicable technologies, and the currently installed infrastructure of gasoline stations, inspection and service facilities, the hybrid vehicle, driven by the combination of gasoline engine and electric motor, is considered to be one of the most realistic solutions. Generally speaking, hybrid systems are classified as series or parallel systems. At Toyota, we have developed the Toyota Hybrid System (hereinafter referred to as the THS) by combining the advantages of both systems. In this sense the THS could be classified as a parallel-series type of system. Since the THS constantly optimizes engine operation, emissions are cleaner and better fuel economy can be achieved. During braking, Kinetic energy is recovered by the motor, thereby reducing fuel consumption and subsequent CO 2 emissions. Emissions and fuel economy are greatly improved by using the THS for the power train system. However, the THS incorporates engine, motor, battery and other components, each of which has its own particular capability. In other words, the driving force must be generated within the limits of each respective component. In particular, since the battery output varies greatly depending on its level of charge, the driving force has to be controlled with this in mind. This report clarifies the performance required of the respective THS components based on the driving force necessary for a vehicle. The method of controlling the driving force, both when the battery has high and low charge, is also described. 2. Toyota hybrid system (THS) [1,2] As Fig. 1 shows, the THS is made up of a hybrid transmission, engine and battery. 2.1. Hybrid transmission The transmission consists of motor, generator, power split device and reduction gear. The power split device is a planetary gear. Sun gear, ring gear and planetary carrier are directly connected to generator, motor and engine, respectively. The ring gear is also connected to the reduction gear. Thus, engine power is split into the generator and the driving wheels. With this type of mechanism, the

汽车专业英语课文翻译4

Fuel Supply System of Gasoline Engine(UNIT SEVEN) All the gasoline engines have substantially identical fuel systems and run on a mixture consisting of fuel vapor and air. The fuel system comprises the units designed to store, clear and deliver fuel, the units intended to clean air and a unit for preparing a mixture from fuel vapor and air. In a fuel system different components are used to supply fuel from the fuel tank into the engine cylinder. Some of the important components are fuel tank, fuel pump, fuel filter, carburetor, intake manifold and fuellines or tubes connecting the tank, pump and the carburetor. The fuel tank is a fuel container used for storing fuel. It is made of sheet metal. It is attached to the vehicle frame with metal traps and is located at the rear of the vehicle. They are mounted in a boot or boot-floor pan in case of front-engined cars and small commercial vehicles. In order to strengthen the tank as well as to prevent surging of fuel when the vehicle rounds a curve of suddenly stops, baffle plates are attached to the inside of the tank. A cap is used to close the filler opening of the tank. The fuel line is attached at or near the bottom of the tank with a filtering element placed at the connection. The other components of the fuel tank are the fuel gauge sending unit, a vent pipe, receiving unit. To prevent the dirt and water from entering the luggage compartment, a sealing strip is fitted between the fuel tank and boot floor pan. Moreover to limit the transmission of frame distortion to the tank giving rise to squeaking as the metal parts get rubbed together, rubber or felt pads are often fitted between the mountings and the tank. Provision is also made against drumming of the tank by these mountings. The tank may be placed at the side of the chassis frame for convenience in case of large commercial vehicles. The length of the connecting lines or tubes from the tank to the carburetor is also restricted by this at the same time. A porous filter is attached to the outlet lines. By drawing fuel from the tank through the filter, any water in the bottom of the tank as well as any dirt into the fuel gathers on the surface of the filter. To keep the fuel always under atmospheric pressure, the filter pipe or tank is vented. In order to prevent dirt in the fuel from entering the fuel pump or carburetor, fuel filters and screens are used in the fuel system. If the dirt is not removed from the fuel, the normal operation of these units will be prevented. The engine performance will also be reduced.