搜档网
当前位置:搜档网 › 土木工程专业英语原文及翻译

土木工程专业英语原文及翻译

土木工程专业英语原文及翻译
土木工程专业英语原文及翻译

成绩

徐州工程学院

08 级土木(1) 班课程考试试卷

考试科目专业英语

考试时间

学生姓名

所在院系土木学院

任课教师

徐州工程学院印制

Stability of Slopes

9.1 Introduction

Translational slips tend to occur where the adjacent stratum is at a relatively shallow depth below the surface of the slope:the failure surface tends to be plane and roughly parallel to the https://www.sodocs.net/doc/b43049138.html,pound slips usually occur where the adjacent stratum is at greater depth,the failure surface consisting of curved and plane sections.

In practice, limiting equilibrium methods are used in the analysis of slope stability. It is considered that failure is on the point of occurring along an assumed or a known failure surface.The shear strength required to maintain a condition of limiting equilibrium is compared with the available shear strength of the soil,giving the average factor of safety along the failure surface.The problem is considered in two dimensions,conditions of plane strain being assumed.It has been shown that a two-dimensional analysis gives a conservative result for a failure on a three-dimensional(dish-shaped) surface.

9.2 Analysis for the Case of φu =0

This analysis, in terms of total stress,covers the case of a fully saturated clay under undrained conditions, i.e. For the condition immediately after construction.Only moment equilibrium is considered in the analysis.In section, the potential failure surface is assumed to be a circular arc. A trial failure surface(centre O,radius r and length L a

where F is the factor of safety with respect to shear strength.Equating moments about O:

Therefore

(9.1)

The moments of any additional forces must be taken into account.In the event of a tension crack

developing ,as shown in Fig.9.2,the arc length L a is shortened and a hydrostatic force will act normal to the crack if the crack fills with water.It is necessary to analyze the slope for a number of trial failure surfaces in order that the minimum factor of safety can be determined.

Based on the principle of geometric similarity,Taylor[9.9]published stability coefficients for the analysis of homogeneous slopes in terms of total stress.For a slope of height H the stability coefficient (N s) for the failure surface along which the factor of safety is a minimum is

(9.2)

For the case ofφu =0,values of N ss depends on the slope angleβand the depth factor D,where DH is the depth to a firm stratum.

Gibson and Morgenstern [9.3] published stability coefficients for slopes in normally consolidated clays in which the undrained strength c u(φu =0) varies linearly with depth.

Example 9.1

A 45°slope is excavated to a depth of 8 m in a deep layer of saturated clay of unit weight 19 kN/m3:the relevant shear strength parameters are c u =65 kN/m2 andφu

In Fig.9.4, the cross-sectional area ABCD is 70 m2.

Weight of soil mass=70×19=1330kN/m

The centroid of ABCD is 4.5 m from O.The angle AOC is 89.5°and radius OC is 12.1 m.The arc length ABC is calculated as 18.9m.The factor of safety is given by:

This is the factor of safety for the trial failure surface selected and is not necessarily the minimum factor of safety.

The minimum factor of safety can be estimated by using Equation 9.2.

From Fig.9.3,β=45°and assuming that D is large,the value of N s

9.3 The Method of Slices

αand the height, measured on the centre-1ine,is h. The factor of safety is defined as the ratio of the available shear strength(τf)to the shear strength(τm) which must be mobilized to maintain a condition of limiting equilibrium, i.e.

The factor of safety is taken to be the same for each slice,implying that there must be mutual support between slices,i.e. forces must act between the slices.

The forces (per unit dimension normal to the section) acting on a slice are:

1.The total weight of the slice,W=γb h (γsat where appropriate).

2.The total normal force on the base,N (equal to σl).In general this

force has two components,the effective normal force N'(equal toσ'l ) and the boundary water force U(equal to ul ),where u is the pore water pressure at the centre of the base and l is the length of the base.

3.The shear force on the base,T=τm l.

4.The total normal forces on the sides, E1 and E2.

5.The shear forces on the sides,X1 and X2.

Any external forces must also be included in the analysis.

The problem is statically indeterminate and in order to obtain a solution assumptions must be made regarding the interslice forces E and X:the resulting solution for factor of safety is not exact.Considering moments about O,the sum of the moments of the shear forces T on the failure arc AC must equal the moment of the weight of the soil mass ABCD.For any slice the lever arm of W is rsinα,

therefore

∑Tr=∑Wr sinα

Now,

For an analysis in terms of effective stress,

Or

(9.3)

where L a is the arc length AC.Equation 9.3 is exact but approximations are introduced in determining the forces N'.For a given failure arc the value of F will depend on the way in which the forces N' are

estimated.

The Fellenius Solution

In this solution it is assumed that for each slice the resultant of the interslice forces is zero.The solution involves resolving the forces on each slice normal to the base,i.e.

N'=WCOSα-ul

Hence the factor of safety in terms of effective stress (Equation 9.3) is given by

(9.4)

The components WCOSαand Wsinαcan be determined graphically for each slice.Alternatively,the value of αcan be measured or calculated.Again,a series of trial failure surfaces must be chosen in order to obtain the minimum factor of safety.This solution underestimates the factor of safety:the error,compared with more accurate methods of analysis,is usually within the range 5-2%.

For an analysis in terms of total stress the parameters C u andφu are used and the value of u in Equation 9.4 is zero.If φu=0 ,the factor of safety is given by

(9.5)

As N’ does not appear in Equation 9.5 an exact value of F is obtained.

The Bishop Simplified Solution

In this solution it is assumed that the resultant forces on the sides of the

slices are horizontal,i.e.

X l-X2=0

For equilibrium the shear force on the base of any slice is

Resolving forces in the vertical direction:

(9.6)

It is convenient to substitute

l=b secα

From Equation 9.3,after some rearrangement,

(9.7)

The pore water pressure can be related to the total ‘fill pressure’ at any

point by means of the dimensionless pore pressure ratio,defined as

(9.8)

(γsat where appropriate).For any slice,

Hence Equation 9.7 can be written:

(9.9)

As the factor of safety occurs on both sides of Equation 9.9,a process of successive approximation must be used to obtain a solution but convergence is rapid.

Due to the repetitive nature of the calculations and the need to select an adequate number of trial failure surfaces,the method of slices is particularly suitable for solution by computer.More complex slope geometry and different soil strata can be introduced.

In most problems the value of the pore pressure ratio r u is not constant over the whole failure surface but,unless there are isolated regions of high pore pressure,an average value(weighted on an area basis) is normally used in design.Again,the factor of safety determined by this method is an underestimate but the error is unlikely to exceed 7%and in most cases is less than 2%.

Spencer [9.8] proposed a method of analysis in which the resultant Interslice forces are parallel and in which both force and moment equilibrium are satisfied.Spencer showed that the accuracy of the Bishop simplified method,in which only moment equilibrium is satisfied, is due to the insensitivity of the moment equation to the slope of the interslice forces.

Dimensionless stability coefficients for homogeneous slopes,based on Equation 9.9,have been published by Bishop and Morgenstern [9.2].It can be shown that for a given slope angle and given soil properties th e factor of safety varies linearly with γu and can thus be expressed as

F=m-nγu(9.10)

where,m and n are the stability coefficients.The coefficients,m and n are

functions ofβ,φ’,the dimensionless number c'/γand the depth factor D.

Example 9.2

Using the Fellenius method of slices,determine the factor of safety,in terms of effective stress,of the slope shown in Fig.9.6 for the given failure surface.The unit weight of the soil,both above and below the water table,is 20 kN/m 3 and the relevant shear strength parameters are c’=10 kN/m2andφ’=29°. W) of each slice is given by

W=γbh=20×1.5×h=30h kN/m

The height h for each slice is set off below the centre of the base and the

normal and tangential components hcosαand hsinα

Wcosα=30h cosα

W sinα=30h sinα

The pore water pressure at the centre of the base of each slice is taken to beγw z w,where z w is the vertical distance of the centre point below the water table (as shown in figure).This procedure slightly overestimates t he pore water pressure which strictly should be) γw z e,where z e is the vertical distance below the point of intersection of the water table and the equipotential through the centre of the slice base.The error involved is on the safe side.

The arc length (L a) is calculated as 14.35 mm.The results are given in

Table 9.1

∑Wcosα=30×17.50=525kN/m

∑W sinα=30×8.45=254kN/m

∑(wcos α-ul)=525—132=393kN/m

9.4 Analysis of a Plane Translational Slip

It is assumed that the potential failure surface is parallel to the surface of the slope and is at a depth that is small compared with the length of the slope. The slope can then be considered as being of infinite length,with end effects being ignored.The slope is inclined at angle βmz (0

In terms of effective stress,the shear strength of the soil along the failure plane is

and the factor of safety is

The expressions forσ,τandμare:

The following special cases are of interest.If c’=0 and m=0 (i.e. the soil

between the surface and the failure plane is not fully saturated),then

(9.11)

If c’=0 and m=1(i.e. the water table coincides with the surface of the slope),then:

(9.12)

It should be noted that when c’=0 the factor of safety is independent of

the depth z.If c’ is greater than zero,the factor of safety is a function of z, and βmay exceedφ’ provided z is less than a critical value.

For a total stress analysis the shear strength parameters c u andφu are used with a zero value of u. Example 9.3

A long natural slope in a fissured overconsolidated clay is inclined at 12°to the horizontal.The water table is at the surface and seepage is roughly parallel to the slope.A slip has developed on a plane parallel to the surface at a depth of 5 m.The saturated unit weight of the clay is 20 kN/m3.The peak strength parameters are c’=10 kN/m2andφ’=26°;the residual strength parameters are c r’=0 andφr’=18°.Determine the factor of safety alo ng the slip plane(a)in terms of the peak strength parameters (b)in terms of the residual strength parameters.

With the water table at the surface(m=1),at any point on the slip plane,

Using the peak strength parameters,

Then the factor of safety is given by

Using the residual strength parameters,the factor of safety can be

obtained from Equation 9.12:

9.5 General Methods of Analysis

Morgenstern and Price[9.4]developed a general analysis in which all boundary and equilibrium conditions are satisfied and in which the failure surface may be any shape,circular,non-circular or compound.The soil mass above the failure plane is divided into sections by a number of vertical planes and the problem is rendered statically determinate by assuming a relationship between the forces E and X on the vertical boundaries between each section.This assumption is of the form

X=λf(x)E (9.13)

where f(x)is an arbitrary function describing the pattern in which the ratio X/E varies across the soil mas s andλis a scale factor.The value ofλis obtained as part of the solution along with the factor of safety F.The values of the forces E and X and the point of application of E can be determined at each vertical boundary.For any assumed function f(x) it is necessary to examine the solution in detail to ensure that it is physically reasonable (i.e. no shear failure or tension must be implied within the soil mass above the failure surface). The choice of the function f(x) does not appear to influence the computed value of F by more than about 5% and f(x)=l is a common assumption.

The analysis involves a complex process of iteration for the values ofλ and F,described by

Morgenstern and Price[9.5],and the use of a computer is essential.

Bell [9.1] proposed a method of analysis in which all the conditions of equilibrium are satisfied and the assumed failure surface may be of any shape.The soil mass is divided into a number of vertical slices and statical determinacy is obtained by means of an assumed distribution of normal stress along the failure surface.

Sarma [9.6] developed a method,based on the method of slices,in which the critical earthquake acceleration required to produce a condition of limiting equilibrium is determined.An assumed distribution of vertical interslice forces is used in the analysis.Again,all the conditions of equilibrium are satisfied and the assumed failure surface may be of any shape.The static factor of safety is the factor by which the shear strength of the soil must be reduced such that the critical acceleration is zero.The use of a computer is also essential for the Bell and Sarma methods and all solutions must be checked to ensure that they are physically acceptable.

References

[9.1]Bell,J,M.(1968):’General Slope Stability Analysis’, Journal ASCE,V01.94,No.SM6.

:‘Stability Coefficients for Earth Slopes Geotechnique,.

,Vo1.1 5,No.1.

‘A Numerical Method for Solving the Equations of Stability of General Slip Surfaces’Computer Journal,Voi.9,P.388.

[9.6]Sarma,S.K. (1973):’Stability Analysis of Embankments and Slopes’,Geotechnique,Vo1.23,No.2.

[9.7]Skempton,A.W.(1970):’First-Time Slides in Overconsolidated Clays’(Technical Note),

[9.8]Spencer,E.(1 967):‘A Method of Analysis of the Stability of Embankments Assuming Parallel Inter-Slice

Forces’,Geotechnique,.

[9.9]Taylor,D.W.(1937):’Stability of Earth Slopes’,Journal of the Boston Society of Civil Engineers,Vo1.24,No.3

边坡稳定

9.1 引言

重力和渗透力易引起天然边坡、开挖形成的边坡、堤防边坡和土坝的不稳定性。最重要的边坡破坏的类型如图9.1所示。在旋滑中,破坏面部分的形状可能是圆弧或非圆弧线。总的来说,匀质土为圆弧滑动破坏,而非匀质土为非圆弧滑动破坏。平面滑动和复合滑动发生在那些强度差异明显的相邻地层的交界面处。

平面滑动易发生在相邻地层处于边坡破坏面以下相对较浅深度的地方:破坏面多为平面,且与边坡大致平行。复合滑动通常发生在相邻地层处于深处的地段,破坏面由圆弧面和平面组成。

在实践中极限平衡法被用于边坡稳定分析当中。它假定破坏面是发生在沿着一个假想或已知

破坏面的点上的。土的有效抗剪强度与保持极限平衡状态所要求的抗剪强度相比,就可以得到沿着破坏面上的平均安全系数。问题以二维考虑,即假想为平面应变的情况。二维分析为三维(碟形)面解答提供了保守的结果。

9.2 φu =0情况的分析

在这种分析方法中,应用总应力法,适用于完全饱和粘土在不条件排水下的情况。如建造完工的瞬间情况。这种分析中只考虑力矩平衡。此间,假定潜在破坏面为圆弧面。图9.2展示了一个试验性破坏面(圆心O,半径r,长度L

a

)。潜在的不稳定性取决于破坏面以上土体的总重量(单位长度上的重量W)。为了达到平衡,必须沿着破坏面传递的抗剪强度表示如下:

其中 F 是就抗剪强度而言的安全系数.关于 O点力矩平衡:

因此

(9.1)

其它外力的力矩必须亦予以考虑。在张裂发展过程中,如图9.2所示,如果裂隙中充满水,弧

长L

a

会变短,超孔隙水压力将垂直作用在裂隙上。有必要用一系列试验性破坏面来对边坡进行分析,从而确定最小的安全系数。

基于几何相似原理,泰勒[9.9]发表了《稳定系数》,用于在总应力方面对匀质土边坡进行分

析。对于一个高度为H的边坡,沿着安全系数最小的破坏面上的稳定系数(N

s

)为:

(9.2)

对于φ

u =0的情况, N

s

的值可以从图9.3中得到。N

s

值取决于边坡坡角β和高度系数 D,其

中DH 是到稳固地层的深度。

吉布森和摩根斯特恩[9.3]发表了《不排水强度c

u (φ

u

=0)随深度线性变化的正常固结粘土边

坡的稳定系数》。

例题9.1

一个坡角为45°的边坡,在容重为19 kN/m3的饱和粘土的深地层中挖至8 m深处:有效抗剪

强度参数为c

u =65 kN/m2 及φ

u

=0。试确定图9.4中试验性破坏面上的安全系数。

在图9.4中,ABCD的纵横面积为70 m2。土体重量=70×19=1330kN/m

ABCD的形心距O点4.5 m。AOC的角度为89.5°,半径OC为12.1 m。弧长ABC经计算为18.9m。安全系数如下给出:

这是给定的试验性破坏面的安全系数,不一定是最小的安全系数。

最小的安全系数通过公式9.2计算得到。由图9.3知,β=45°及假设D很大,N

s

的值为0.18。那么:

9.3条分法

在这种方法中,潜在破坏面再次被假定为以O为圆心,以r为半径的圆弧。试验性破坏面(AC)以上的土体(ABCD),如图9.5所示,被垂直划分为一系列宽度为b的条块。每个条块的底边假定为直线。对于任何一个条块来说,其底边与水平线的夹角为α,它的高,从中心线测量,为h。

安全系数定义为有效抗剪强度(τ

f )与保持边限平衡状态的抗剪强度(τ

m

)的比值,即:

每个条块的安全系数取相同值,表明条块之间必须互相支持,即条块间必须有力的作用。

作用于条块上的力(条块每个单元维上法向力)如下:

1.条块总重量,W=γb h(适当时用γ

sat

2.作用于底边上总法向力,N(等于σl)。总体上,这个力有两部分:有效法向力N'(等于σ'l )和边界孔隙水压力U(等于ul),其中u是底边中心的孔隙水压力,而l是底边长度。

3.底边上的剪力,T=τ

m

l。

4.侧面上总法向力, E

1和E

2

5.侧面上总剪力,X

1和X

2

任何的外力也必须包含在分析之中。

这是一种静不定问题,为了得到解决,就必须对于条块间作用力E 和X作出假定:安全系数的最终解答是不准确的。

考虑到围绕O点的力矩,破坏弧AC上的剪力T的力矩总和,必须与土体ABCD重量所产生的力矩相等。对于任何条块,W的力臂为rsinα,

因此

∑Tr=∑Wr sinα

则,

对于有效应力方面的分析:

或者

(9.3)

其中L

a

是弧AC的长度。公式9.3是准确的,但是当确定力N'时引入了近似。对于给定的破坏面,F的取值将决定于力N'的计算方法。

费伦纽斯解

在这种解法中,假定对于任何一个条块,条间的相互作用力为零。解答包括了解出每个条块垂直于底边的作用力,即:

N'=WCOSα-ul

因此,在有效应力方面的安全系数(公式9.3),由下式计算:

(9.4)

对于每个条块,Wcosα和Wsinα可以通过图表法确定。α的取值可以通过测量或计算得到。同样地,也必须选择一系列试验性的破坏面来获得最小的安全系数。这种解法所得的安全系数:与更精确的分析方法相比,其误差通常为5-2%。

应用总应力法分析时,使用参数C

u 和φ

u

,公式9.4中u取零。如果φ

u

=0,那么安全系数为:

(9.5) 因为N’没有出现在公式9.5中,故得到的安全系数F值是精确的。毕肖普简化解

在这种解法中,假定条块侧面的力是水平的,即:

X l-X2=0

为了达到平衡,任何一个条块底边上的剪力为:

解答垂直方向上的力:

(9.6) 很方便得到:

l=b secα

从公式9.3,通过一些重新整理,

(9.7)

孔隙水压力通过孔压比,可以与任何点的与总“填充压力”相联系,定义为:

(9.8)

).对于任何条块,

(适当时用γ

sat

因此公式9.7可写为:

(9.9)

因为安全系数出现在公式9.9的两边,必须使用一系列近似,才能获得解答,但收敛很快。

基于计算的重复性,需要选择充分数量的试验性破坏面。条分法特别适合于计算机解答。可以引入更复杂的边坡几何学和不同的土层。

在整个破坏面上是不一致的,但一旦存在独立的高孔压在大多数问题中,孔压力比的取值r

u

区,通常在设计中采用平均值(单位面积上的荷重)。同样的,这种方法确定的安全系数过低,但误差不超过7%,多数情况下小于2%。

斯班瑟 [9.8] 提出了一种分析方法,在此法中,条块间的作用力是水平的,且满足力和力矩平衡。斯班瑟得到了只满足力矩平衡的毕肖普简化解,其精确度取决于边坡条块间作用力力矩平衡的不敏感性。

基于公式9.9的匀质土边坡的稳定系数,是由毕肖普和摩根斯特恩[9.2]发表的。由此可见,对

线性变化,因此可以表示为:

于给定坡角和给定土性的边坡,安全系数随γ

u

F=m-γu (9.10)

其中m和n是稳定系数。系数 m和n 是β,φ’, c'/γ及深度系数 D的函数。

例题 9.2

用费伦纽斯条分法,确定如图9.6所示给定破坏面的边坡在采用有效应力法时的安全系数。土的容重在水位线上下,均为20 kN/m 3。有关的抗剪强度参数为c’=10 kN/m2及φ’=29°。

由公式9.4计算安全系数。土体被划分为宽度为l.5 m 的条块。给出每个条块的重量(W) :W=γbh=20×1.5×h=30h kN/m

每个条块的高h 从底边中心算起,法向和切向的分量hcosα和 hsinα,由图解法确定,如图9.6所示:

Wcosα=30h cosα

W sinα=30h sinα

每个条块底边中心的孔隙水压力取γ

w z

w

,其中z

w

是水面以下中心点的垂直距离(如图所示)。

在这个过程中,把孔隙水压力估算的稍高,严格说来,应为γ

w z

e

,其中z

e

是水位线与等势线的交点以

下至条块底边中点的距离.误差在安全范围内。

弧长(L

a

) 经计算为14.35 m。结果在表9.1中给出:

∑Wcosα=30×17.50=525kN/m

∑W sinα=30×8.45=254kN/m

∑(wcos α-ul)=525—132=393kN/m

9.4 平面滑动的分析

假定潜在破坏面与边坡面平行,所在深度与边坡长度相比很小。那么,边坡可以看作无限长,忽略端部效应。边坡与水平线成β角,破坏面深度为z如图9.7中所示。水位线在破坏面以上高度mz (0

应用有效应力法,沿着破坏面上的土的抗剪强度为:

安全系数为:

σ,τ和μ表达为:

接下来的特殊情况是需要引起注意的。如果c’=0 和 m=0 (即坡面与破坏面间的土是不完全饱和的),那么:

(9.11)

如果c’=0 和m=1(即水位线与边坡面一致) ,那么:

(9.12)

应当注意的是,当c’=0 时,安全系数是与深度无关的。如果c’ 大于零,那么安全系数就是z 的函数,如果z 比规定值还小的话,β可能会超过φ’。

应用总应力分析法,需使用抗剪强度参数c

u 和φ

u

,而u取值为零。

例题 9.3

一个含裂隙的超固结粘土天然边坡,与水平面成12°倾角。水位线处于边坡表面且渗流方向与边坡方向大致平行。平行于边坡表面以下5 m深处发生平面滑动。粘土的饱和重度为20 kN/

m3。峰值强度参数为c’=10 kN/m2和φ’=26°。残余强度参数为c

r ’=0 和φ

r

’=18°。

确定沿着滑动面的安全系数:

(a)在峰值强度参数方面的安全系数

(b)在残余强度参数方面的安全系数。

在坡面的水位线处(m=1),滑动面上任何一点,

运用峰值强度参数,

给出安全系数

运用峰值强度参数,安全系数可由公式9.12得到:

9.5一般分析法

摩根斯特恩和普莱斯[9.4]提出了一般分析法,此法满足所有的边界条件和平衡条件,破坏面可以是任何形状,圆弧,非圆弧或符合型。破坏面以上的土体被划分为一系列垂直的平面,问题通过假定每部分之间垂直边界上的作用力E 和X的关系而转化为静定。这个假定的形式为X=f(x)E (9.13)

其中f(x)是描述随土体而变化的比值X/E 的形式的任意函数,而λ是尺寸效应系数。λ的值是在解安全系数F时一同获得的。在每个垂直边界上能够确定作用力E 和X的值及作用点。对于任意的假定函数 f(x) ,有必要仔细地检查解答,以确定其在物理学上的合理性(即破坏面以上土体中没有剪切破坏或张力)。函数f(x)的选择对于F的计算值的影响不能超过 5% ,通常假定

f(x)=l。

这种分析包含了λ和F值相互作用的复杂过程,如摩根斯特恩和普莱斯[9.5]所描述的那样,计算机的运用是必不可少的。

贝尔[9.1] 提出了一种满足所有平衡情况,假定破坏面可能是任何形状的分析方法。土体被划分成一系列垂直的条块,通过沿着破坏面上的法向作用力的假想分配,转化为静定问题。

萨尔玛 [9.6] 基于条分法发展了一种方法,在此法中,产生极限平衡所要求的临界地震加速度是确定的。这种分析方法在分析中假定了条块间垂直作用力的分配。同样的,满足所有的平衡条件,破坏面可以是任何形状。静安全系数是土的抗剪强度必须减小,以致于临界加速度为零时的系数。

计算机的使用对于贝尔法和萨尔玛法来说,是必不可少的。所有的解答必须要检查,以确保它们在物理学上是可以接受的。

参考文献

[9.1]贝尔,J,M.(1968):《边坡总体稳定性分析》,美国土木工程师学会期刊,V01.94,No.SM6.

[9.2]毕肖普,A.W.和摩根斯特恩,N.R.(1960):《土坡的稳定系数》,岩土学,.

[9.3]吉布森,R.E.和摩根斯特恩,N.R.(1962): 《正常固结粘土开挖的稳定性记录》,岩土学

[9.4]摩根斯特恩,N.R.和普莱斯,V.E.(1965):《整个滑动表面的稳定性分析》, 岩土学,Vo1.1 5,No.1. [9.5]摩根斯特恩,N.R.和普莱斯,V.E.(1967):《解决整个滑动表面的平衡稳定性的数值法》,计算机期刊,

Voi.9,P.388.

[9.6]萨尔玛,S.K. (1973):《堤坝和边坡的稳定性分析》,岩土学,Vo1.23,No.2.

[9.7]斯开普顿,A.W.(1970):《超固结粘土的第一时间滑移》 (技术笔记),岩土学

[9.8]斯班瑟,E.(1967):《假定条块间为水平作用力的堤坝稳定性分析法》,岩土学,.[9.9]泰勒,D.W.(1937):《土坡稳定》,波士顿土木工程期刊,Vo1.24,No.3

出处:

土木工程专业英语词汇(整理版)

第一部分必须掌握,第二部分尽量掌握 第一部分: 1 Finite Element Method 有限单元法 2 专业英语Specialty English 3 水利工程Hydraulic Engineering 4 土木工程Civil Engineering 5 地下工程Underground Engineering 6 岩土工程Geotechnical Engineering 7 道路工程Road (Highway) Engineering 8 桥梁工程Bridge Engineering 9 隧道工程Tunnel Engineering 10 工程力学Engineering Mechanics 11 交通工程Traffic Engineering 12 港口工程Port Engineering 13 安全性safety 17木结构timber structure 18 砌体结构masonry structure 19 混凝土结构concrete structure 20 钢结构steelstructure 21 钢-混凝土复合结构steel and concrete composite structure 22 素混凝土plain concrete 23 钢筋混凝土reinforced concrete 24 钢筋rebar 25 预应力混凝土pre-stressed concrete 26 静定结构statically determinate structure 27 超静定结构statically indeterminate structure 28 桁架结构truss structure 29 空间网架结构spatial grid structure 30 近海工程offshore engineering 31 静力学statics 32运动学kinematics 33 动力学dynamics 34 简支梁simply supported beam 35 固定支座fixed bearing 36弹性力学elasticity 37 塑性力学plasticity 38 弹塑性力学elaso-plasticity 39 断裂力学fracture Mechanics 40 土力学soil mechanics 41 水力学hydraulics 42 流体力学fluid mechanics 43 固体力学solid mechanics 44 集中力concentrated force 45 压力pressure 46 静水压力hydrostatic pressure 47 均布压力uniform pressure 48 体力body force 49 重力gravity 50 线荷载line load 51 弯矩bending moment 52 torque 扭矩 53 应力stress 54 应变stain 55 正应力normal stress 56 剪应力shearing stress 57 主应力principal stress 58 变形deformation 59 内力internal force 60 偏移量挠度deflection 61 settlement 沉降 62 屈曲失稳buckle 63 轴力axial force 64 允许应力allowable stress 65 疲劳分析fatigue analysis 66 梁beam 67 壳shell 68 板plate 69 桥bridge 70 桩pile 71 主动土压力active earth pressure 72 被动土压力passive earth pressure 73 承载力load-bearing capacity 74 水位water Height 75 位移displacement 76 结构力学structural mechanics 77 材料力学material mechanics 78 经纬仪altometer 79 水准仪level 80 学科discipline 81 子学科sub-discipline 82 期刊journal ,periodical 83文献literature 84 ISSN International Standard Serial Number 国际标准刊号 85 ISBN International Standard Book Number 国际标准书号 86 卷volume 87 期number 88 专著monograph 89 会议论文集Proceeding 90 学位论文thesis, dissertation 91 专利patent 92 档案档案室archive 93 国际学术会议conference 94 导师advisor 95 学位论文答辩defense of thesis 96 博士研究生doctorate student 97 研究生postgraduate 98 EI Engineering Index 工程索引 99 SCI Science Citation Index 科学引文索引

《土木工程专业英语》段兵延第二版全书文章翻译精编版

第一课 土木工程学土木工程学作为最老的工程技术学科,是指规划,设计,施工及对建筑环境的管理。此处的环境包括建筑符合科学规范的所有结构,从灌溉和排水系统到火箭发射设施。 土木工程师建造道路,桥梁,管道,大坝,海港,发电厂,给排水系统,医院,学校,公共交通和其他现代社会和大量人口集中地区的基础公共设施。他们也建造私有设施,比如飞机场,铁路,管线,摩天大楼,以及其他设计用作工业,商业和住宅途径的大型结构。此外,土木工程师还规划设计及建造完整的城市和乡镇,并且最近一直在规划设计容纳设施齐全的社区的空间平台。 土木一词来源于拉丁文词“公民”。在1782年,英国人John Smeaton为了把他的非军事工程工作区别于当时占优势地位的军事工程师的工作而采用的名词。自从那时起,土木工程学被用于提及从事公共设施建设的工程师,尽管其包含的领域更为广阔。 领域。因为包含范围太广,土木工程学又被细分为大量的技术专业。不同类型的工程需要多种不同土木工程专业技术。一个项目开始的时候,土木工程师要对场地进行测绘,定位有用的布置,如地下水水位,下水道,和电力线。岩土工程专家则进行土力学试验以确定土壤能否承受工程荷载。环境工程专家研究工程对当地的影响,包括对空气和地下水的可能污染,对当地动植物生活的影响,以及如何让工程设计满足政府针对环境保护的需要。交通工程专家确定必需的不同种类设施以减轻由整个工程造成的对当地公路和其他交通网络的负担。同时,结构工程专家利用初步数据对工程作详细规划,设计和说明。从项目开始到结束,对这些土木工程专家的工作进行监督和调配的则是施工管理专家。根据其他专家所提供的信息,施工管理专家计算材料和人工的数量和花费,所有工作的进度表,订购工作所需要的材料和设备,雇佣承包商和分包商,还要做些额外的监督工作以确保工程能按时按质完成。 贯穿任何给定项目,土木工程师都需要大量使用计算机。计算机用于设计工程中使用的多数元件(即计算机辅助设计,或者CAD)并对其进行管理。计算机成为了现代土木工程师的必备品,因为它使得工程师能有效地掌控所需的大量数据从而确定建造一项工程的最佳方法。 结构工程学。在这一专业领域,土木工程师规划设计各种类型的结构,包括桥梁,大坝,发电厂,设备支撑,海面上的特殊结构,美国太空计划,发射塔,庞大的天文和无线电望远镜,以及许多其他种类的项目。结构工程师应用计算机确定一个结构必须承受的力:自重,风荷载和飓风荷载,建筑材料温度变化引起的胀缩,以及地震荷载。他们也需确定不同种材料如钢筋,混凝土,塑料,石头,沥青,砖,铝或其他建筑材料等的复合作用。 水利工程学。土木工程师在这一领域主要处理水的物理控制方面的种种问题。他们的项目用于帮助预防洪水灾害,提供城市用水和灌溉用水,管理控制河流和水流物,维护河滩及其他滨水设施。此外,他们设计和维护海港,运河与水闸,建造大型水利大坝与小型坝,以及各种类型的围堰,帮助设计海上结构并且确定结构的位置对航行影响。 岩土工程学。专业于这个领域的土木工程师对支撑结构并影响结构行为的土壤和岩石的特性进行分析。他们计算建筑和其他结构由于自重压力可能引起的沉降,并采取措施使之减少到最小。他们也需计算并确定如何加强斜坡和填充物的稳定性以及如何保护结构免受地震和地下水的影响。 环境工程学。在这一工程学分支中,土木工程师设计,建造并监视系统以提供安全的饮用水,同时预防和控制地表和地下水资源供给的污染。他们也设计,建造并监视工程以控制甚至消除对土地和空气的污染。他们建造供水和废水处理厂,设计空气净化器和其他设备以最小化甚至消除由工业加工、焚化及其他产烟生产活动引起的空气污染。他们也采用建造特殊倾倒地点或使用有毒有害物中和剂的措施来控制有毒有害废弃物。此外,工程师还对垃圾掩埋进行设计和管理以预防其对周围环境造成污染。

土木工程专业英语原文及翻译

土木工程专业英语原文 及翻译 文档编制序号:[KKIDT-LLE0828-LLETD298-POI08]

08 级土木(1) 班课程考试试卷 考试科目专业英语 考试时间 学生姓名 所在院系土木学院 任课教师 徐州工程学院印制 Stability of Slopes Introduction Translational slips tend to occur where the adjacent stratum is at a relatively shallow depth below the surface of the slope:the failure surface tends to be plane and roughly parallel to the slips usually occur where the adjacent stratum is at greater depth,the failure surface consisting of curved and plane sections. In practice, limiting equilibrium methods are used in the analysis of slope stability. It is considered that failure is on the point of occurring along an assumed or a known failure surface.The shear strength required to maintain a condition of limiting equilibrium is compared with the available shear strength of the soil,giving the average factor of safety along the failure surface.The problem is considered in two dimensions,conditions of plane strain being assumed.It has been shown that a two-dimensional analysis gives a conservative result for a failure on a three-dimensional(dish-shaped) surface. Analysis for the Case of φu =0 This analysis, in terms of total stress,covers the case of a fully saturated clay under undrained conditions, . For the condition immediately after construction.Only moment equilibrium is considered in the analysis.In section, the potential failure surface is assumed to be a circular arc. A trial failure surface(centre O,radius r and length L a where F is the factor of safety with respect to shear strength.Equating moments about O:

土木工程专业英语正文课文翻译

第一课土木工程学 土木工程学作为最老的工程技术学科,是指规划,设计,施工及对建筑环境的管理。此处的环境包括建筑符合科学规范的所有结构,从灌溉和排水系统到火箭发射设施。 土木工程师建造道路,桥梁,管道,大坝,海港,发电厂,给排水系统,医院,学校,公共交通和其他现代社会和大量人口集中地区的基础公共设施。他们也建造私有设施,比如飞机场,铁路,管线,摩天大楼,以及其他设计用作工业,商业和住宅途径的大型结构。此外,土木工程师还规划设计及建造完整的城市和乡镇,并且最近一直在规划设计容纳设施齐全的社区的空间平台。 土木一词来源于拉丁文词“公民”。在1782年,英国人John Smeaton为了把他的非军事工程工作区别于当时占优势地位的军事工程师的工作而采用的名词。自从那时起,土木工程学被用于提及从事公共设施建设的工程师,尽管其包含的领域更为广阔。 领域。因为包含范围太广,土木工程学又被细分为大量的技术专业。不同类型的工程需要多种不同土木工程专业技术。一个项目开始的时候,土木工程师要对场地进行测绘,定位有用的布置,如地下水水位,下水道,和电力线。岩土工程专家则进行土力学试验以确定土壤能否承受工程荷载。环境工程专家研究工程对当地的影响,包括对空气和地下水的可能污染,对当地动植物生活的影响,以及如何让工程设计满足政府针对环境保护的需要。交通工程专家确定必需的不同种类设施以减轻由整个工程造成的对当地公路和其他交通网络的负担。同时,结构工程专家利用初步数据对工程作详细规划,设计和说明。从项目开始到结束,对这些土木工程专家的工作进行监督和调配的则是施工管理专家。根据其他专家所提供的信息,施工管理专家计算材料和人工的数量和花费,所有工作的进度表,订购工作所需要的材料和设备,雇佣承包商和分包商,还要做些额外的监督工作以确保工程能按时按质完成。 贯穿任何给定项目,土木工程师都需要大量使用计算机。计算机用于设计工程中使用的多数元件(即计算机辅助设计,或者CAD)并对其进行管理。计算机成为了现代土木工程师的必备品,因为它使得工程师能有效地掌控所需的大量数据从而确定建造一项工程的最佳方法。 结构工程学。在这一专业领域,土木工程师规划设计各种类型的结构,包括桥梁,大坝,发电厂,设备支撑,海面上的特殊结构,美国太空计划,发射塔,庞大的天文和无线电望远镜,以及许多其他种类的项目。结构工程师应用计算机确定一个结构必须承受的力:自重,风荷载和飓风荷载,建筑材料温度变化引起的胀缩,以及地震荷载。他们也需确定不同种材料如钢筋,混凝土,塑料,石头,沥青,砖,铝或其他建筑材料等的复合作用。 水利工程学。土木工程师在这一领域主要处理水的物理控制方面的种种问题。他们的项目用于帮助预防洪水灾害,提供城市用水和灌溉用水,管理控制河流和水流物,维护河滩及其他滨水设施。此外,他们设计和维护海港,运河与水闸,建造大型水利大坝与小型坝,以及各种类型的围堰,帮助设计海上结构并且确定结构的位置对航行影响。 岩土工程学。专业于这个领域的土木工程师对支撑结构并影响结构行为的土壤和岩石的特性进行分析。他们计算建筑和其他结构由于自重压力可能引起的沉降,并采取措施使之减少到最小。他们也需计算并确定如何加强斜坡和填充物的稳定性以及如何保护结构免受地震和地下水的影响。 环境工程学。在这一工程学分支中,土木工程师设计,建造并监视系统以提供安全的饮用水,同时预防和控制地表和地下水资源供给的污染。他们也设计,建造并监视工程以控制甚至消除对土地和空气的污染。

曹植《泰山梁甫行》原文、译文及赏析

泰山梁甫行 八方各异气[1],干里殊风雨。 剧哉边海民[2],寄身于草野[3]。 妻子象禽一兽[4],行止依林阻[5]。 柴门何萧条[6],狐兔翔我宇[7]。 【注解】 [1]异气:气候不同。 [2]剧:艰苦。 [3]草墅:用草搭盖而成的简陋房屋。 [4]行止:行动的踪迹。 [5]林阻:山林险阻之地。 [6]柴门:用树枝等物编成的门。 [7]翔:绕行。 【译文】 八方的气候各不相同,千里之内的风雨形态不一。海边的贫民多么艰苦啊,破旧的草屋是他们的栖身之地。妻子和儿子像禽一兽一样生活,盘桓在险阻的山林里。简陋的柴门如此冷清,狐兔在周围自一由穿梭毫无顾忌。 【鉴赏】 曹植自曹丕篡汉后,在自己生存的艰难不幸中,逐渐体会到下层人民的痛苦。他在《泰山梁甫行》中,以白描的手法,反映了边海农村的残破荒凉景象,表现了对下层人民的深切同情。'八方各异气,千里殊风雨。'是说天下的自然环境不一样,所遭受的风雨灾害也不一样。言外之意是说,海边气候潮湿,风雨狂暴,海啸龙卷风也时有发生,是不适合人生存的地方。这两句突出边海人民生存环境的恶劣。'剧哉边海民,寄身于草野。'痛苦啊,海边的人民,他们生活在荒野草丛林木中,多么荒凉,多么凄惨。这本是野兽出入的地方,可他们却长期的与野兽同一居。所以'妻子象禽一兽,行止依林阻。'这是对妻子以及孩子的整体形象描写,从中我们不但看到海民衣不蔽体蓬头垢面的野人一样的粗俗艰苦的生活方式,也可以想见他们与世隔绝的愚钝颓废形象。他们依靠自然环境的险阻,和野兽争夺相间生存,他们不但经受生活的艰难困苦,而且还有随时被野兽吃掉的生存忧惧。'柴门何萧条,狐兔翔

我宇。'柴门简陋凄清,在海风中嗦嗦摇荡,狐狸兔子好象从天上飞来一样从屋檐下飞来窜去。这里通过狐狸、兔子的侧面描写,反衬出边海人们生活环境的荒蛮以及边海人们的恐惧与凄楚。本文以白描的手法,言简意赅地全方位展现了边海人们的痛苦生活。

土木工程专业英语课文原文及对照翻译

土木工程专业英语课文原 文及对照翻译 Newly compiled on November 23, 2020

Civil Engineering Civil engineering, the oldest of the engineering specialties, is the planning, design, construction, and management of the built environment. This environment includes all structures built according to scientific principles, from irrigation and drainage systems to rocket-launching facilities. 土木工程学作为最老的工程技术学科,是指规划,设计,施工及对建筑环境的管理。此处的环境包括建筑符合科学规范的所有结构,从灌溉和排水系统到火箭发射设施。 Civil engineers build roads, bridges, tunnels, dams, harbors, power plants, water and sewage systems, hospitals, schools, mass transit, and other public facilities essential to modern society and large population concentrations. They also build privately owned facilities such as airports, railroads, pipelines, skyscrapers, and other large structures designed for industrial, commercial, or residential use. In addition, civil engineers plan, design, and build complete cities and towns, and more recently have been planning and designing space platforms to house self-contained communities. 土木工程师建造道路,桥梁,管道,大坝,海港,发电厂,给排水系统,医院,学校,公共交通和其他现代社会和大量人口集中地区的基础公共设施。他们也建造私有设施,比如飞机场,铁路,管线,摩天大楼,以及其他设计用作工业,商业和住宅途径的大型结构。此外,土木工程师还规划设计及建造完整的城市和乡镇,并且最近一直在规划设计容纳设施齐全的社区的空间平台。 The word civil derives from the Latin for citizen. In 1782, Englishman John Smeaton used the term to differentiate his nonmilitary engineering work from that of the military engineers who predominated at the time. Since then, the term civil engineering has often been used to refer to engineers who build public facilities, although the field is much broader 土木一词来源于拉丁文词“公民”。在1782年,英国人John Smeaton为了把他的非军事工程工作区别于当时占优势地位的军事工程师的工作而采用的名词。自从那时起,土木工程学被用于提及从事公共设施建设的工程师,尽管其包含的领域更为广阔。 Scope. Because it is so broad, civil engineering is subdivided into a number of technical specialties. Depending on the type of project, the skills of many kinds of civil engineer specialists may be needed. When a project begins, the site is surveyed and mapped by civil engineers who locate utility placement—water, sewer, and power lines. Geotechnical specialists perform soil experiments to determine if the earth can bear the weight of the project. Environmental specialists study the project’s impact on the local area: the potential for air and

土木工程专业英语

non-destructive test 非破损检验 non-load—bearingwall 非承重墙 non—uniform cross—section beam 变截面粱 non—uniformly distributed strain coefficient of longitudinal tensile reinforcement 纵向受拉钢筋应变不均匀系数 normal concrete 普通混凝土 normal section 正截面 notch and tooth joint 齿连接 number of sampling 抽样数量 O obligue section 斜截面 oblique—angle fillet weld 斜角角焊缝 one—way reinforced(or prestressed)concrete slab “单向板” open web roof truss 空腹屋架, ordinary concrete 普通混凝土(28) ordinary steel bar 普通钢筋(29) orthogonal fillet weld 直角角焊缝(61) outstanding width of flange 翼缘板外伸宽度(57) outstanding width of stiffener 加劲肋外伸宽度(57) over-all stability reduction coefficient of steel beam·钢梁整体稳定系数(58) overlap 焊瘤(62) overturning or slip resistance analysis 抗倾覆、滑移验算(10) P padding plate 垫板(52) partial penetrated butt weld 不焊透对接焊缝(61) partition 非承重墙(7) penetrated butt weld 透焊对接焊缝(60) percentage of reinforcement 配筋率(34) perforated brick 多孔砖(43) pilastered wall 带壁柱墙(42) pit·凹坑(62) pith 髓心(?o) plain concrete structure 素混凝土结构(24) plane hypothesis 平截面假定(32) plane structure 平面结构(11) plane trussed lattice grids 平面桁架系网架(5) plank 板材(65) plastic adaption coefficient of cross—section 截面塑性发展系数(58) plastic design of steel structure 钢结构塑性设计(56) plastic hinge·塑性铰(13) plastlcity coefficient of reinforced concrete member in tensile zone 受拉区混凝土塑性影响系数

梁甫行原文及翻译

梁甫行原文及翻译 梁甫行 魏晋:曹植 八方各异气,千里殊风雨。 剧哉边海民,寄身于草野。(草野一作:草墅) 妻子象禽兽,行止依林阻。 柴门何萧条,狐兔翔我宇。 收藏下载复制完善 译文及注释 译文 八方的气候各不相同,千里之内的风雨形态不一。 海边的贫民多么艰苦啊,平时就住在野外的草棚里。 妻子和儿女像禽兽一样生活,盘桓在险阻的山林里。 简陋的柴门如此冷清,狐兔在房屋周围自在地行走毫无顾忌。 注释 异气:气候不同。殊:不同。 剧:艰苦。 寄身:生活。 草野:野外、原野。

妻子:妻子和儿女。 象:像。 行止:行动的踪迹。 林阻:山林险阻之地。 柴门:用树枝等物编成的门。 萧条:冷清。 翔:悠闲自在地行走。 宇:房屋。▲ 创作背景 曹丕上位后,诗人被贬到贫困的海边,在自己生存的艰难不幸的环境中,看到下层人民的困苦生活,逐渐体会到下层人民的痛苦,有感而发,写下这首慷慨激愤之作。 赏析 此诗描述了边海百姓的艰难生活,比较深刻地反映了那个时代百姓生活困苦不堪的惨痛景象,表现了作者对劳动人民生活的同情。全诗采用了正面描写与侧面烘托的手法,使边海贫民悲惨的生活图景跃然纸上,言简意赅,寓意深刻。 “八方各异气,千里殊风雨”是“剧哉边海民”的衬托。各地的情况虽然不同,但最艰难困顿的要数“边海民”了。

“寄身”三句,实写“边海民”的悲惨生活。他们没身于“草野”,过着非人的生活。生吞活剥,巢息穴居,所以说“象禽兽”;他们不敢出来,怕被人发现、抓走,每天就钻在山林里边所以说“行止依林阻”。一个“依”字把逃民们的实际活动和恐惧心理都表现出来了。 曹植(192-232),字子建,沛国谯(今安徽省亳州市)人。三国曹魏著名文学家,建安文学代表人物。魏武帝曹操之子,魏文帝曹丕之弟,生前曾为陈王,去世后谥号“思”,因此又称陈思王。后人因他文学上的造诣而将他与曹操、曹丕合称为“三曹”,南朝宋文学家谢灵运更有“天下才有一石,曹子建独占八斗”的评价。王士祯尝论汉魏以来二千年间诗家堪称“仙才”者,曹植、李白、苏轼三人耳。 曹植 曹植(192-232),字子建,沛国谯(今安徽省亳州市)人。三国曹魏著名文学家,建安文学代表人物。魏武帝曹操之子,魏文帝曹丕之弟,生前曾为陈王,去世后谥号“思”,因此又称陈思王。后人因他文学上的造诣而将他与曹操、曹丕合称为“三曹”,南朝宋文学家谢灵运更有“天下才有一石,曹子建独占八斗”的评价。王士祯尝论汉魏以来二千年间诗家堪称“仙才”者,曹植、李白、苏轼三人耳。

土木工程专业英语修正版

Take the road of sustainable development civil engineering Abstract: Civil Engineering is the oldest in human history "technical science" as a system of industrial activity, the essence of civil engineering production process, is a technical process Civil engineering is the construction of various facilities in science and technology, collectively, both refer to the construction of the object, that is built on the ground, underground, water facilities, a variety of projects, but also refers to the application of materials, equipment and carried out survey and design , construction, maintenance, repair and other technology. As an important basis for discipline, civil engineering has its important attributes: a comprehensive, social, practical, technical and economic and artistic unity. With the progress of human society and development, civil engineering has already evolved into large-scale comprehensive subject, and has many branches, such as: construction, railroad engineering, road engineering, bridge engineering, specialty engineering structures, water supply and drainage projects, port engineering, hydraulic engineering, environmental engineering and other disciplines. There are six professional civil engineering: architecture, urban planning, civil engineering, built environment and equipment engineering, water supply and drainage works and road and bridge projects. Civil engineering is a form of human activity. Human beings pursued it to change the natural environment for their own benefit. Buildings, transportations, facilities, infrastructures are all included in civil engineering. The development of civil engineering has a long history. Our seniors had left a lot of great constructions to us. For example, Zhao Zhou Bridge is the representative of our Chinese civil engineering masterpieces. It has a history of more than 1300 years and is still service at present. Civil engineering has been so rapid development of the period. A lot of new bridges have been constructed, and many greater plans are under discussion. China is a large county. And she is still well developing. However, civil engineers will be facing more complex problems. We should pay attention to the growing population and a lot of deteriorating infrastructures. We should prepare for the possibility of natural disasters. To meet grow needs in the

(完整版)土木工程专业英语常用词汇

Part IV:Commonly Used Professional Terms of Civil Engineering development organization 建设单位 design organization 设计单位 construction organization 施工单位 reinforced concrete 钢筋混凝土 pile 桩 steel structure 钢结构 aluminium alloy 铝合金 masonry 砌体(工程)reinforced ~ 配筋砌体load-bearing ~ 承重砌体unreinforced ~非配筋砌体 permissible stress (allowable stress) 容许应力plywood 胶合板 retaining wall 挡土墙 finish 装修 finishing material装修材料 ventilation 通风 natural ~ 自然通风 mechanical ~ 机械通风 diaphragm wall (continuous concrete wall) 地下连续墙 villa 别墅 moment of inertia 惯性矩 torque 扭矩 stress 应力normal ~ 法向应力shear ~ 剪应力 strain 应变 age hardening 时效硬化 air-conditioning system空调系统 (air) void ration(土)空隙比 albery壁厨,壁龛 a l mery壁厨,贮藏室 anchorage length锚固长度 antiseismic joint 防震缝 architectural appearance 建筑外观 architectural area 建筑面积 architectural design 建筑设计 fiashing 泛水 workability (placeability) 和易性 safety glass安全玻璃 tempered glass (reinforced glass) 钢化玻璃foamed glass泡沫玻璃 asphalt沥青 felt (malthoid) 油毡 riveted connection 铆接 welding焊接 screwed connection 螺栓连接 oakum 麻刀,麻丝 tee三通管 tap存水弯 esthetics美学 formwork 模板(工程) shoring 支撑 batching 配料 slipform construction (slipforming) 滑模施工 lfit-slab construction 升板法施工 mass concrete 大体积混凝土 terrazzo水磨石 construction joint 施工缝 honeycomb蜂窝,空洞,麻面 piled foundation桩基 deep foundation 深基础 shallow foundation浅基础 foundation depth基础埋深 pad foundation独立基础 strip foundation 条形基础 raft foundation筏基 box foundation箱形基础 BSMT=basement 地下室 lift 电梯electric elevator lift well电梯井 escalator 自动扶梯 Poisson’s ratio 泊松比μ Young’s modulus , modulus of elasticity 杨氏模量,弹性模量E safety coefficient 安全系数 fatigue failure 疲劳破坏 bearing capacity of foundations 地基承载力bearing capacity of a pile 单桩承载力 two-way-reinforcement 双向配筋 reinforced concrete two-way slabs钢筋混凝土双向板 single way slab单向板 window blind 窗帘sun blind wind load 风荷载 curing 养护 watertight concrete 防水混凝土 white cement白水泥 separating of concrete混凝土离折segregation of concrete mortar 砂浆~ joint 灰缝 pilaster 壁柱 fire rating耐火等级 fire brick 耐火砖 standard brick标准砖

《梁甫行》曹植赏析习题及答案

《梁甫行》曹植赏析习题及答案 内容:【原诗】【翻译】【作者】【主题思想】【赏析】 题型:【理解性默写】【选择题】【简答题】 【原诗】 八方各异气,千里殊风雨。剧哉边海民,寄身于草墅。妻子象禽兽,行止依林阻。柴门何萧条,狐兔翔我宇。 【翻译】 八方的气候各不相同,千里之内的风雨形态不一。海边的贫民多么艰苦啊,平时就住在野外的草棚里。妻子和儿女像禽兽一样生活,盘桓在险阻的山林里。简陋的柴门如此冷清,狐兔在周围自在地行走毫无顾忌。 【作者】 曹植(192年-232年12月27日),字子建,沛国谯县(今安徽省亳州市)人,曹植是三国时期著名文学家,作为建安文学的代表人物之一与集大成者,他在两晋南北朝时期,被推尊到文章典范的地位。其代表作有《洛神赋》《白马篇》《七哀诗》等。后人因其文学上的造诣而将他与曹操、曹丕合称为“三曹”。【主旨】 以白描的手法,言简意赅地全方位展现了边海人们的痛苦生活,反映了边海农村的残破荒凉景象,表现了对下层人民的深切同情。 【赏析】 《梁甫行》中,以白描的手法,反映了边海农村的残破荒凉景象,表现了对下层人民的深切同情。 “八方各异气,千里殊风雨。”是说天下的自然环境不一样,所遭受的风雨灾害也不一样。言外之意是说,海边气候潮湿,风雨狂暴,海啸龙卷风也时有发生,是不适合人生存的地方。这两句突出边海人民生存环境的恶劣。“剧哉边海民,寄身於草野。”痛苦啊,海边的人民,他们生活在荒野草丛林木中,多么荒凉,多么凄惨。这本是野兽出入的地方,可他们却长期的与野兽同居。所以“妻子象禽兽,行止依林阻。”这是对妻子以及孩子的整体形象描写,从中我们不但

看到海民衣不蔽体蓬头垢面的野人一样的粗俗艰苦的生活方式,也可以想见他们与世隔绝的愚钝颓废形象。他们依靠自然环境的险阻,和野兽争夺相间生存,他们不但经受生活的艰难困苦,而且还有随时被野兽吃掉的生存忧惧。“柴门何萧条,狐兔翔我宇。”柴门简陋凄清,在海风中嗦嗦摇荡,狐狸兔子好象从天上飞来一样从屋檐下飞来窜去。这里通过狐狸、兔子的侧面描写,反衬出边海人们生活环境的荒蛮以及边海人们的恐惧与凄楚。 【习题】 一、理解性默写: 1、《梁甫行》一诗中突出边海人民生存环境的恶劣的句子是:八方各异气,千里殊风雨。 2、《梁甫行》中描述海边的人民在荒野草丛林木中生活,表现自己对下层人民的同情的句子:剧哉边海民,寄身于草野。 3、《梁甫行》写出了边海人民衣不遮体、粗俗艰苦的生活方式的句子是:妻子象 二、选择题: 1、下列对《梁甫行》理解不正确的一项是( D ) A、《梁甫行》中,以白描的手法,反映了边海农村的残破荒凉景象,表现了诗人对下层人民的深切同情。 B、“八方各异气,千里殊风雨。”是说天下的自然环境不一样,所遭受的风雨灾害也不一样。言外之意是说,海边气候潮湿,风雨狂暴,海啸龙卷风也时有发生,是不适合人生存的地方。这两句突出边海人民生存环境的恶劣。 C、“剧哉边海民,寄身于草野。”痛苦啊,海边的人民,他们生活在荒野草丛林木中,多么荒凉,多么凄惨。 D 、“柴门何萧条,狐兔翔我宇。”这里通过狐狸、兔子的正面描写,反映出边海人们生活环境的荒蛮以及边海人们的恐惧与凄楚。 【解析】D 是侧面描写,反衬……。 2、下列《梁甫行》理解错误的一项是:( D )

《土木工程专业英语》课文翻译 作者 戴俊 第01单元

第一单元 课文 土木工程前言 或许,工程师对于人类文明形成所做出的贡献多于其他专业人才群体。在各个社会中,工程师的作用就是发展技术应用以满足实际需要。例如,应用电力系统向城市供电,应用水轮驱动水碾,应用人造心脏延长生命,等。向我们提供水、燃料、电力的系统,交通网络系统,通讯系统,以及带来其他方便的系统是工程技术应用的产物。尽管真正的工程师们在以上进步和人类幸福中所起的作用,但对他们所起作用的理解仍是不完全的。 工程是将知识转化为实际有效应用的技术,工程师则是在这样的转化中起关键作用的人。工程是服务人类的职业,人类环境是需要考虑的重要事项。通常,区分工程师和科学家一直存在困难,决定科学家的工作在哪里终止,工程师的工作从哪里开始也存在困难。 科学与工程中有联系的工作的基本区别在于它们的目的不同。科学家以发明为目的,而工程师坚持有效使用发明来满足人类的需要。例如,德国物理学家亨利奇·赫兹发现了无线电波,而古里耶尔莫·马克尼则利用无线电波发展了无线电信技术,这是一项工程奇迹。在相关科学家建立了核裂变的科学原理后,制造原子武器、建造核电厂的艰难工作则由电力、化学和机械工程师来完成。 土木工程是以向人类提供安全、舒适住所为目的的工程分支。住所是人类的基本需要之一,它由土木工程师负责提供。供水和灌溉系统的有效规划能增加一个国家的粮食产量。住所除了简单的掩蔽功能外,土木工程师还能将其建造来为居住者提供安宁、舒适的生活。世界上的工程奇迹——从塔形结构到今天的薄壳结构——都是土木工程发展的结果。道路、铁路、桥梁等交通网线是土木工程师的劳动果实,没有这样的交通网线,社会将不可能得到发展。 任何工程学科都是由各种专业分支构成的巨大领域,土木工程的主要专业分支如下: 1.结构工程 结构工程是土木工程的最重要专业分支,结构的建造需要有效的规划、设计和施工方法,以实现完整的建造目的。一般地,结构工程建造包含五个步骤: ●定位,并合理排列结构构件,形成确定的形式,以实现最佳的使用功能。 ●决定作用于结构上不同力的大小、方向和性质。 ●结构分析,弄清受上述作用力的结构构件的行为特征。 ●结构设计,以保证不同载荷作用下的结构稳定性。 ●结构施工,采用精心选择的材料,由熟练工人完成。 2.岩土工程 为了实现建筑于地面结构的有效功能,必须知道土的特征。岩土工程给出土的基本知识体系,这一分支涉及以下方面: ●土——“土力学”下的材料——的性质和行为特征。 ●结构、机器等基础的不同类型及其稳定性。 岩土工程也涉及基础的分析、设计和施工。 3.流体力学、水力学和水力机械

相关主题