搜档网
当前位置:搜档网 › 电子信息英语专业英语词组专业英语b篇翻译

电子信息英语专业英语词组专业英语b篇翻译

电子信息英语专业英语词组专业英语b篇翻译
电子信息英语专业英语词组专业英语b篇翻译

Translated by何莹婷,版权没有,翻印不究。有错误欢迎指正:)

Unit3

27-2In the binary system of representation the base is 2, and only two numerals 0 and 1 are required to represent a number. The numerals 0 and 1 have the same meaning as in the decimal system, but a different interpretation is placed on the position occupied by a digit. In the binary system the individual digits represent the coefficients of powers of two rather than ten as in the decimal system. For example, the decimal number 19 is written in the binary representation as 10011 since

10011=1×24+0×23+0×22+1×21+1×20=16+0+0+2+1=19

A short list of equivalent numbers in decimal and binary notation is given in Table 3.2.

二进制示数系统中的基数是二,且只有0和1两个数被用以示数。0和1在这里与在十进制中具有一样的意义,但每个数位表示的不一样。二进制系统中每个数字表示二的幂系数,而十进制中表示十的幂系数。例如,十进制数19在二进制中表示为10011因为

10011=1×24+0×23+0×22+1×21+1×20=16+0+0+2+1=19

二进制和十进制数相等数字见表3.2.

27-3A general method for converting from a decimal to a binary number is indicated in Table 3.3. The procedure is the following. Place the decimal number (in this illustration, 19) on the extreme right. Next divide by 2 and place the quotient (9) to the left and indicate the remainder (1) directly below it. Repeat this process (for the next column 9÷2 =4 and a remainder of 1) until a quotient of 0 is obtained. The array of 1’s and 0’s in the second row is the binary representation of the origin decimal number. In this example, decimal 19=10011 binary.

十进制转换成二进制的一般方法如图3.3。过程如下:把十进制数(图中的19)放在最右端,接下来除以2,把商(9)放在左边并直接在其下方标明余数(1)。重复这个步骤(下一列为9÷2=4余1),直到商为0截止。第二行中的1和0就是原始十进制数的二进制表示。此例中,十进制19=二进制10011.

28-1A binary digit (a 1 or a 0) is called a bit. A group of bits that has the same significance is called a byte, word, or code. For example, to represent the 10 numerals (0, 1, 2, …, 9) and the 26 letters of the English alphabet would require 36 different combinations of 1’s and 0’s. Since 25<36<26, then a minimum of 6 bits per bite are required in order to accommodate all the alphanumeric characters. In this sense a bite is sometimes referred to as a character and a group of one or more characters as a word.

一位二进制数(一个1或0)叫做比特。一组具有相同意义的比特叫做字节,词,或代码。例如,表示10个数字(0,1,2,...9)和26个英文字母要用到36种不同的1和0的组合。因为25<36<26,那么表示所有这些字母数字字符组最少需要6比特每字节。这种情况下一字节有时候被称为一个字符和一个或多个字符组成的字符串。

29-1The parameters of a physical device (for example, VCE·sat of a transistor) are not identical from sample to sample, and they also vary with temperature. Furthermore, ripple or voltage spikes may exist in the power supply or ground leads, and other sources of unwanted signals, called noise, may be present in the circuit. For these reasons the digital levels are not specified precisely, but as indicated by the shaded region in Figure 3.6, each state is defined by a voltage range about a designated level, such as 4±1 V and 0.2±0.2 V.

每个实体器件样本的参数(如晶体管的VCE·sat )是不完全相同的,它们还会随温度变化。而且,电源或地线可能存在电压脉动或电压峰值,其他干扰信号——噪声也可能出现在电路

中。由于这些原因,数字电平没有明确的规定,但如图3.6中阴影所示,将每个状态定义为指定电平的电压范围,例如4±1 V 和0.2±0.2 V。

Unit4

37-1The materials that make up our universe are composed of over one hundred basic and individual types of matter called elements. Ninety-two of these elements occur naturally and the remainders are man-made. Each element has a separate identify of its own, that is, no two elements have the same physical and chemical properties, nor can an element be subdivided by ordinary physical and chemical means into simple elements.[1] Examples of elements are gold, mercury and oxygen.

构成宇宙的物质是由一百多种基本的不同类型的物质——元素组成的。其中92种元素是天然形成的,其他的则是人造的。每种元素都各有其自己的标识,也就是说,元素的物理和化学特性是独一无二的,一种元素也不可以用物理和化学手段再分成简单的元素。例如金,汞和氧元素。

37-3Electrons whirl around nuclei in much the same manner that the planets of our solar system travel around the sun. The difference between an atom of one element and that of another is in the number of protons and neutrons contained in the nucleus.[2] All the elements in the universe, and therefore all matter, is composed of protons, neutrons, and electrons.

电子围绕原子核旋转,其方式类似于太阳系中行星围绕太阳旋转。一种元素的原子和另一种元素的原子的差别在于其原子核中的质子数和中子数。宇宙中的所有元素,也就是说所有的物质,都是由质子,中子和电子组成的。

37-4There must be force of attraction between a nucleus and the electrons surrounding it, otherwise the electrons would fly off into space, in order to understand its nature, we find it helpful to call this force a charge. The charge of the nucleus is defined as positive, and the opposite charge of the electron, negative. In view of the fact that opposites attract, the force between the nucleus and the rotating electron around it prevents the electron from flying off into space.

在原子核与其周围的电子间必然存在着吸引力,否则电子将会飞离原子核,为了理解它的性质,我们把这种力称为电荷。原子核电荷定义为正电荷,电子的电荷则相反,为负电荷。鉴于异性相吸,原子核和围绕其旋转的电子间的力阻止了电子飞离到空间中。

38-last para Impurities may be added to pure semiconductors. This results in semiconductor materials, which may either have an excess of free electrons or a deficiency of orbital electrons. When an excess of electrons is present we call the material N-type; when lack of orbital electrons occurs, we call the material P-type. Both N-type and P-type semiconductors are made by treated materials. such as germanium and silicon with impurities ,such as arsenic and indium. The addition of impurities to semiconductors is called doping.

杂质被加入到纯的半导体中。这会导致半导体材料中有过剩的自由电子或轨道电子缺失。有过剩电子时材料被称为n型;缺失轨道电子时材料被称为p型。N型和P型半导体都由加工材料制成。例如有杂质的锗和硅,砷和铟。往半导体中加入的杂质添加物叫掺杂质。

Unit5

50-2At first, these disk drives used 14 inch disks, but now they use 5 1/4inch, 3 1/2inch,2 1/2

inch, and 1 4/5inch diameters. In contrast to the floppy disk drive, hard disk drives hold from 80 megabytes to gigabytes and terabytes of information. When purchasing a hard disk, consider storage capacity and seek time, a measure of a hard disk’s access speed. The smaller the numbers, the faster the disk. In the past, 65 milliseconds was the standard access time, but today the standard is less than 7 milliseconds.

起初,这些磁盘驱动采用14英寸磁盘,但现在采用的是5 1/4英寸,2 1/2英寸和1 4/5直径的磁盘。与软盘驱动截然不同的是,硬盘驱动保存着兆字节到千兆字节、万兆字节的信息。购买硬盘时要考虑存储容量和寻道时间及存取速度。这些数字越小,磁盘就运行得越快。在过去,标准存取时间为65毫秒,而现在的标准为低于7毫秒。

50-3Storing data on hard disks is similar to storing data on diskettes. In order to read or write data on the surface of the spinning disk platter, the disk drives are designed with access arms, or actuators.[1] The access arms, or actuators, contain one or more read/write heads per disk surface. As the disk rotates at a high rate of speed, usually 3,600 revolution per minute, the read/write heads move across its surface. These read/write heads float on a cushion of air and do not actually touch the surface of the disk.[2] The distance between the head and the surface varies from approximately ten to twenty millionths of an inch. If some form of contamination is introduced or if the alignment of the read/write heads is altered by something accidentally jarring the computer, the disk head can collide and damage the disk surface, causing a loss of data. This event is known as a head crash. Because of the time needed to repair the disk and to reconstruct the data that was lost, head crashes can be extremely costly to users in terms of both time and money.

硬盘上的数据存储与软盘上的类似。为了在旋转的磁盘盘片表面读写数据,磁盘驱动器被设计成具有存取和传动装置。存取和传动装置由每个盘片表面的一个或多个读写头构成。当盘片以通常为3600转每分的速度高速旋转时,读写头移过盘片表面。这些读写头在高压气流上漂浮,移动时并不与盘片表面真正接触。读写头与盘片表面的距离约为一万到两千万分之一英寸。如果有污染物介入,或读写头队列被电脑的意外震动改变,读写头会碰撞并损坏盘片表面,引起数据丢失。这种情况叫做磁头碰撞。由于修复磁盘并重建数据需要一定的时间,磁头碰撞会花费用户相当多的金钱和时间。

50-5The sector method for physically organizing data on disks divides each track on the disk surface into individual storage areas called sectors. Each sectors can contain a specified number of bytes. Data is referenced by indicating the surface, track, and sector where the data is stored.

用扇区方式物理地在磁盘上组织数据是将盘片表面分成独立的存储区域,称之为扇区。每个扇区能包含特定字节数。数据通过指示存储着数据的盘片表面,轨道和扇区来引用。

51-6Most optical disks are prerecorded and cannot be modified by the user. These disks are used for applications such as an auto parts catalog where the information is changed only occasionally, such as once a year, and a new updated optical disk is created.[3] Optical disk devices that provide for one-time recording are called WORM devices, an acronym for write once, read many. Erasable optical disk drives are just starting to be used. The most common erasable optical drives use magneto-optical technology, in which a magnetic field changes the polarity of a spot on the disk that has been heated by a laser.[4]

大多数光盘是事先录好的,且不能被用户修改。这种光盘用于信息量大,不需要经常更改信息内容的场合。例如,一个汽车零件目录,其中的信息是经过一段时间(比如一年)才更新一次,需要更新时再制作一张新的光盘就可以了。只能刻录一次的光盘设备叫WORM设备,是write once, read many的缩写。可擦写光盘设备刚开始被使用。最常见的可擦写光盘驱动采用磁光技术,在这种技术中,磁场改变了磁盘上被激光加热的点的极性。

Unite6

65-1

PCM is dependent on three separate operations: sampling, quantizing, and coding. Many different schemes for performing these three functions have evolved during recent years, and we shall describe the main ones.[1] In these descriptions we shall see how a speech channel of telephone quality maybe conveyed as a series of amplitude values, each value being represented, that is, coded, as a sequence of 8 binary digits.[2] Furthermore, we shall prove that a minimum theoretical sampling frequency of order 6.8 kilohertz (kHz) is required to convey a voice channel occupying the range 300 Hz to 3.4 kHz.[3] Practical equipments, however, normally use a sampling rate of 8 kHz, and if 8-digits per sample value are used, the voice channel becomes represented by a stream of pulses with a repetition rate of 64 kHz. Figure 6.2 illustrates the sampling, quantizing, and coding processes.

脉冲编码调制依靠三个独立的运作:采样,量化,编码。近年来,人们对这三个环节的实现提出了许多不同的方案,我们将对其中一些主要的方案进行讨论。在这些讨论中,我们会看到话路中的语音信号是如何转换成一个幅值序列的,而每个幅值又被编码,即以8位二进制数的序列表示。而且我们将证明,为了变换频率范围为300hz-3.4khz的话路信号,理论上的最小采样频率为6.8khz。但实际的设备通常采用8 kHz的采样速度,而如果采用8位每样本的值,则会出现重复速率为64 kHz的脉冲流。采样,量化和编码过程如图6.2所示。

67-2Digital transmission provides a powerful method for overcoming noisy environments. Noise can be introduced into transmission path in many different ways; perhaps via a nearby lightning strike, the sparking of a car ignition system, or the thermal low-level noise within the communication equipment itself. It is the relationship of the true signal to the noise signal, known as the signal-to-noise ratio, which is of most interest to the communication engineer. Basically, if the signal is very large compared to the noise level, then a perfect message can take place; however, this is not always the case. For example, the signal received from a satellite, located in far outer space, is very weak and is at a level only slightly above that of the noise.[4] Alternative examples may be found within terrestrial systems where, although the message signal is strong, so is the noise power.

数字传输是克服噪声环境的一种有力方式。噪声会以多种不同方式引入传输路径。也许是附近的闪电,汽车点火装置的火花,或者是通信设备中热的低电平噪声。确实信号与噪声信号间的关系称为信噪比,这是通信工程师最感兴趣的问题。基本上说,若信号相对噪声占的比重很大,这条信息将得到完美传输。但事实并不总是这样。比如,从位于遥远太空中的卫星接收到的信号极其微弱,其电平仅比噪声稍高一点。另一个例子是地面系统,尽管信息信号强,但噪声功率也强。

67-3If we consider binary transmission, the complete information about a particular message will always be obtained by simply detecting the presence or absence of the pulse. By comparison, most other forms of transmission systems convey the message information using the shape, or level of the transmitted signal; parameters that are most easily affected by the noise and attenuation introduced by the transmission path.[5] Consequently there is an inherent advantage for overcoming noisy environments by choosing digita1 transmission.

要是我们考虑二进制传输,完整的信息总会通过简单地检测脉冲的有无获得。相比之下,许多其他形式的传输系统利用被传信号的波形或电平高低来传送信息,而这些参数又极易受到

传输路径中噪声和衰耗的影响。因此选择数字传输对克服噪声环境有固有的优势。

67-4So far in this discussion we have assumed that each voice channel has a separate coder, the unit that converts sampled amplitude values to a set of pulses; and decoder, the unit that performs the reverse operation. This need not be so, and systems are in operation where a single codec (i.e., coder and its associated decoder) is shared between 24, 30, or even 120 separate channels. A high-speed electronic switch is used to present the analog information signal of each channel, taken in turn, to the codec. The codec is then arranged to sequentially sample the amplitude value, and code this value into the 8-digit sequence. Thus the output to the codec may be seen as a sequence of 8 pulses relating to channel 1, then channel 2, and so on. This unit is called a time division multiplexer (TDM), and 15 illustrated in Figure 6.3. The multiplexing principle that is used is known as word interleaving. Since the words, or 8-digit sequences, are interleaved in time.目前我们在这个讨论中假定每个话路有单独的编码器,也就是将采样幅值转换成脉冲序列的单元;并有单独的解码器,也就是执行相反操作的单元。其实并不需要这样,系统靠单一的编译码器(编码器和其关联的解码器)运行,它有24,30,甚至120个单独的信道。高速电子开关用以表示每个信道的模拟信息信号,并把信号依次送入编译码器。而后编译码器顺序地进行幅值采样,并把幅值编排成8位码序列。这样编译码器的输出看起来就像一串关于信道1,信道2等的8位脉冲序列。这个单元叫做时分多路器。图6.3说明了15个信道的时分多路器工作原理。采用的分路原理叫字交叉。因为每个字或8位码序列是在一段时间内交叉存取的。

电子技术专业英语翻译

基本电路 包括电路模型的元素被称为理想的电路元件。一个理想的电路元件是一个实际的电气元件的数学模型,就像一个电池或一个灯泡。重要的是为理想电路元件在电路模型用来表示实际的电气元件的行为可接受程度的准确性。电路分析,本单位的重点,这些工具,然后应用电路。电路分析基础上的数学方法,是用来预测行为的电路模型和其理想的电路元件。一个所期望的行为之间的比较,从设计规范,和预测的行为,形成电路分析,可能会导致电路模型的改进和理想的电路元件。一旦期望和预测的行为是一致的,可以构建物理原型。 物理原型是一个实际的电气系统,修建从实际电器元件。测量技术是用来确定实际的物理系统,定量的行为。实际的行为相比,从设计规范的行为,从电路分析预测的行为。比较可能会导致在物理样机,电路模型,或两者的改进。最终,这个反复的过程,模型,组件和系统的不断完善,可能会产生较准确地符合设计规范的设计,从而满足需要。 从这样的描述,它是明确的,在设计过程中,电路分析中起着一个非常重要的作用。由于电路分析应用电路模型,执业的工程师尝试使用成熟的电路模型,使设计满足在第一次迭代的设计规范。在这个单元,我们使用20至100年已测试通过机型,你可以认为他们是成熟的。能力模型与实际电力系统理想的电路元件,使电路理论的工程师非常有用的。 说理想电路元件的互连可用于定量预测系统的行为,意味着我们可以用数学方程描述的互连。对于数学方程是有用的,我们必须写他们在衡量的数量方面。在电路的情况下,这些数量是电压和电流。电路分析的研究,包括了解其电压和电流和理解上的电压施加的限制,目前互连的理想元素的每一个理想的电路元件的行为电路分析基础上的电压和电流的变量。电压是每单位电荷,电荷分离所造成的断电和SI单位伏V = DW / DQ。电流是电荷的流动速度和具有的安培SI单位(I= DQ/ DT)。理想的基本电路元件是两个终端组成部分,不能细分,也可以在其终端电压和电流的数学描述。被动签署公约涉及元素,当电流通过元素的参考方向是整个元素的参考电压降的方向端子的电压和电流的表达式使用一个积极的迹象。 功率是单位时间内的能量和平等的端电压和电流的乘积;瓦SI单位。权力的代数符号解释如下: 如果P> 0,电源被传递到电路或电路元件。 如果p<0,权力正在从电路或电路元件中提取。 在这一章中介绍的电路元素是电压源,电流源和电阻器。理想电压源保持一个规定的电压,不论当前的设备。理想电流源保持规定的电流不管了整个设备的电压。电压和电流源是独立的,也就是说,不是任何其他电路的电流或电压的影响;或依赖,就是由一些电路中的电流或电压。一个电阻制约了它的电压和电流成正比彼此。有关的比例常数电压和一个电阻值称为其电阻和欧姆测量。 欧姆定律建立相称的电压和电流的电阻。具体来说,V = IR电阻的电流流动,如果在它两端的电压下降,或V=_IR方向,如果在该电阻的电流流是在它两端的电压上升方向。 通过结合对权力的方程,P = VI,欧姆定律,我们可以判断一个电阻吸收的功率:P = I2R= U2/ R 电路节点和封闭路径。节点是一个点,两个或两个以上的电路元件加入。当只有两个元素连接,形成一个节点,他们表示将在系列。一个闭合的路径是通过连接元件追溯到一个循环,起点和终点在同一节点,只有一次每遇到中间节点。 电路是说,要解决时,两端的电压,并在每个元素的电流已经确定。欧姆定律是一个重要的方程,得出这样的解决方案。 在简单的电路结构,欧姆定律是足以解决两端的电压,目前在每一个元素。然而,对于更复杂的互连,我们需要使用两个更为重要的代数关系,被称为基尔霍夫定律,来解决所有的电压和电流。 基尔霍夫电流定律是: 在电路中的任何一个节点电流的代数和等于零。 基尔霍夫电压定律是: 电路中的任何封闭路径上的电压的代数和等于零。 1.2电路分析技术 到目前为止,我们已经分析应用结合欧姆定律基尔霍夫定律电阻电路相对简单。所有的电路,我们可以使用这种方法,但因为他们而变得结构更为复杂,涉及到越来越多的元素,这种直接的方法很快成为累赘。在这一课中,我们介绍两个电路分析的强大的技术援助:在复杂的电路结构的分析节点电压的方法,并网电流的方

电子信息工程专业课程翻译中英文对照表

电子信息工程专业课程名称中英文翻译对照 (2009级培养计划)

实践环节翻译 高等数学Advanced Mathematics

大学物理College Physics 线性代数Linear Algebra 复变函数与积分变换Functions of Complex Variable and Integral Transforms 概率论与随机过程Probability and Random Process 物理实验Experiments of College Physics 数理方程Equations of Mathematical Physics 电子信息工程概论Introduction to Electronic and Information Engineering 计算机应用基础Fundamentals of Computer Application 电路原理Principles of Circuit 模拟电子技术基础Fundamentals of Analog Electronics 数字电子技术基础Fundamentals of Digital Electronics C语言程序设计The C Programming Language 信息论基础Fundamentals of Information Theory 信号与线性系统Signals and Linear Systems 微机原理与接口技术Microcomputer Principles and Interface Technology 马克思主义基本原理Fundamentals of Marxism 思想、理论和“三个代表” 重要思想概论 Thoughts of Mao and Deng 中国近现代史纲要Modern Chinese History 思想道德修养与法律基 础 Moral Education & Law Basis 形势与政策Situation and Policy 英语College English 体育Physical Education 当代世界经济与政治Modern Global Economy and Politics 卫生健康教育Health Education 心理健康知识讲座Psychological Health Knowledge Lecture 公共艺术课程Public Arts 文献检索Literature Retrieval 军事理论Military Theory 普通话语音常识及训练Mandarin Knowledge and Training 大学生职业生涯策划 (就业指导) Career Planning (Guidance of Employment ) 专题学术讲座Optional Course Lecture 科技文献写作Sci-tech Document Writing 高频电子线路High-Frequency Electronic Circuits 通信原理Communications Theory 数字信号处理Digital Signal Processing 计算机网络Computer Networks 电磁场与微波技术Electromagnetic Field and Microwave Technology 现代通信技术Modern Communications Technology

电子信息类专业英语翻译

1.This electron beam sweeps across each line at a uniform rate,then flies back to scan another line directly below the previous one and so on,until the horizontal lines into which it is desired to break or split the picture have been scanned in the desired sequence. 电子束以均匀的速率扫描每一行,然后飞速返回去扫描下一行,直到把被扫描的图像按所希望的顺序分割成行。 2.The technical possibilities could well exist,therefore,of nation-wide integrated transmission network of high capacity,controlled by computers,interconnected globally by satellite and submarine cable,providing speedy and reliable communications throughout the word 因此,在技术上完全可能实现全国性的集成发送网络。这种网络容量大,由计算机控制,并能通过卫星和海底电缆实现全球互联,提供世界范围的高速、可靠的通信。 3.Transit time is the primary factor which limits the ability of a transistor to operate at high frequency. 渡越时间是限制晶体管高频工作能力的主要因素 4.The intensity of sound is inversely proportional to the square of the distance measured from the source of the sound. 声强与到声源的距离的平方成反比。 5.The attenuation of the filter is nearly constant to within 0.5 dB over the entire frequency band. 该滤波器的衰减近于恒定, 整个频带内的变化在0.5 dB以内。 6.At present, the state of most semiconductor device technology is such that the device design and process technology must be supplemented by screening and inspection procedures, if ultimate device reliability is to be obtained and controlled. 目前, 大多数半导体器件的技术尚未十分完善, 以至若要获得并控制器件最终的可靠性, 就必须辅以筛选和检验, 以弥补设计和工艺技术之不足 7.Bandwidth of transistor amplifiers vary from about 250 MHz in the L band to 1000 MHz in the X band. 晶体管放大器的带宽在L波段约为250 MHz, 在X波段为1000 MHz。 8.The output of the differential amplifier is fed to the circuit’s output stage via an offset-compensation network, which causes the op-amp’s output to center at zero volts. The output stage takes the form of a complementary emitter follower, and provides a low-impedance output. 差动放大级的输出通过一个失调补偿网络与输出级相连, 目的是使运放的输出以0 V为中心。输出级采用互补的射极跟随器的形式以使输出阻抗很低 9.Because of the very high open-loop voltage gain of the op-amp, the output is driven into positive saturation (close to +V) when the sample voltage goes slightly above the reference voltage, and driven into negative saturation (close to-V) when the sample voltage goes slightly below the reference voltage. 由于运放的开环电压增益很高, 当取样电压略高于参考电压时, 输出趋向于正向饱和状态(接近+V)。当取样电压低于参考电压时, 输出趋向于负向饱和状态(接近-V)。 10.If the signal source were direct connected instead of capacitor coupled, there would be a low resistance path from the base to the negative supply line, and this would affect the circuit bias conditions. 如果信号源和电路不是用电容耦合而是直接相连,从基极到负电源线就会一个低阻通路,并且这将影响到电路偏置状态 11.The differential amplifier has a high-impedance (constant-current)“tail”to give it a high input impedance and a high degree of common-mode signal rejection. It also has a high-impedance collector (or drain) load, to give it a large amount of signal-voltage gain (typically about 100 dB). 差动放大极有一个高阻抗的“尾巴”(恒流源)以提供高输入阻抗和对共模信号的深度抑制,同时,它还具有一个高阻抗和集电极或漏极负载以提供高的信号电压增益(典型的数据是100dB). 12.On the other hand, a DC negative-logic system, as in Figure 3.6(b), is one which designates the more negative voltage state of the bit as the 1 level and the more positive as the 0 level. 另一方面, 如图3.6(b)所示, 把比特的较低的电压状态记为1电平, 较高的电压状态记为0电平, 这样的系统称为直流负逻辑系统。 13.For example, to represent the 10 numerals (0, 1, 2, …, 9) and the 26 letters of the English alphabet would require 36

《机械工程专业英语教程》课文翻译

Lesson 1 力学的基本概念 1、词汇: statics [st?tiks] 静力学;dynamics动力学;constraint约束;magnetic [m?ɡ'netik]有磁性的;external [eks't?:nl] 外面的, 外部的;meshing啮合;follower从动件;magnitude ['m?ɡnitju:d] 大小;intensity强度,应力;non-coincident [k?u'insid?nt]不重合;parallel ['p?r?lel]平行;intuitive 直观的;substance物质;proportional [pr?'p?:??n?l]比例的;resist抵抗,对抗;celestial [si'lestj?l]天空的;product乘积;particle质点;elastic [i'l?stik]弹性;deformed变形的;strain拉力;uniform全都相同的;velocity[vi'l?siti]速度;scalar['skeil?]标量;vector['vekt?]矢量;displacement代替;momentum [m?u'ment?m]动量; 2、词组 make up of由……组成;if not要不,不然;even through即使,纵然; Lesson 2 力和力的作用效果 1、词汇: machine 机器;mechanism机构;movable活动的;given 规定的,给定的,已知的;perform执行;application 施用;produce引起,导致;stress压力;applied施加的;individual单独的;muscular ['m?skjul?]]力臂;gravity[ɡr?vti]重力;stretch伸展,拉紧,延伸;tensile[tensail]拉力;tension张力,拉力;squeeze挤;compressive 有压力的,压缩的;torsional扭转的;torque转矩;twist扭,转动;molecule [m likju:l]分子的;slide滑动; 滑行;slip滑,溜;one another 互相;shear剪切;independently独立地,自立地;beam梁;compress压;revolve (使)旋转;exert [iɡ'z?:t]用力,尽力,运用,发挥,施加;principle原则, 原理,准则,规范;spin使…旋转;screw螺丝钉;thread螺纹; 2、词组 a number of 许多;deal with 涉及,处理;result from由什么引起;prevent from阻止,防止;tends to 朝某个方向;in combination结合;fly apart飞散; 3、译文: 任何机器或机构的研究表明每一种机构都是由许多可动的零件组成。这些零件从规定的运动转变到期望的运动。另一方面,这些机器完成工作。当由施力引起的运动时,机器就开始工作了。所以,力和机器的研究涉及在一个物体上的力和力的作用效果。 力是推力或者拉力。力的作用效果要么是改变物体的形状或者运动,要么阻止其他的力发生改变。每一种

微电子专业英语

微电子学专业词汇 A be absorb in 集中精力做某事 access control list 访问控制表 active attack 主动攻击 activeX control ActiveX控件 advanced encryption standard AES,高级加密标准 algorithm 算法 alteration of message 改变消息 application level attack 应用层攻击 argument 变量 asymmetric key cryptography 非对称密钥加密 attribute certificate属性证书 authentication 鉴别 authority 机构 availability 可用性 Abrupt junction 突变结 Accelerated testing 加速实验 Acceptor 受主 Acceptor atom 受主原子 Accumulation 积累、堆积 Accumulating contact 积累接触 Accumulation region 积累区 Accumulation layer 积累层 Active region 有源区 Active component 有源元 Active device 有源器件 Activation 激活 Activation energy 激活能 Active region 有源(放大)区 Admittance 导纳 Allowed band 允带 Alloy-junction device 合金结器件 Aluminum(Aluminium) 铝 Aluminum – oxide 铝氧化物 Aluminum passivation 铝钝化 Ambipolar 双极的 Ambient temperature 环境温度 Amorphous 无定形的,非晶体的 Amplifier 功放扩音器放大器Analogue(Analog) comparator 模拟比较器 Angstrom 埃 Anneal 退火

电子信息专业英语复习资料

电子信息专业英语复习资料 一、基本术语(英译汉) 1.probe探针 2.real time operational system 实时操作系统 3.debugger 调试器 4.sourse code 源代码 5.software radio wireless LAN 软件无线电网络 6.base station 基站 7.top-down approach 自顶向下分析法 8.variable 变量 9.data compress 数据压缩 10.signal conditioning circuit 信号调理电路 11.Chebyshev Type Ⅰfilter 切比雪夫Ⅰ型滤波器 12.vertical resolution 垂直分辨率 13.device driver 设备驱动 https://www.sodocs.net/doc/d71097671.html,piler 编译器 15.template 模板 16.concurrent process 并发进程 17.object recognition 目标识别 18.Discrete Time Fourier Transform 离散傅立叶变换 https://www.sodocs.net/doc/d71097671.html,bined circuit 组合逻辑电路 20.impedance transform 阻抗变换器 21.voltage source 电压源22.passive component 无源器件 23.quality factor 品质因数 24.unit-impulse response 单位脉冲响应 25.noise origin 噪声源 26.Domino effect 多米诺效应 27.output load 输出负载 28.cordless phone 无绳电话 29.Antenna 天线 30.harmonic interference 谐波干涉 31.Parallel Resonant 并联谐振 32.voltage control oscillator 压控振荡器 33.adaptive delta modulation 自适应增量调制 34.amplitude modulation 调幅 二、缩略语(写出全称) 1.LSI:large scale integration 2.PMOS :p-type metal-oxide semiconductor 3.CT:cycle threshold 4.MRI:magnetic resonance imaging 5.ROM:read-only memory 6.DRAM :dynamic random access memory 7.TCXO :temperature compensated X'tal (crystal) Oscillator https://www.sodocs.net/doc/d71097671.html,B:Universal Serial Bus 9.DCT:discrete cosine transform

电子电气类专业英语单词汇总

课一A Communications 通讯 1. equation n.相等, 平衡, 综合体, 2. communication n. 通信, 通讯, 交通communicate v.沟通, 通信, 3. triode n.三极管 4. storage n. 存储 5.transmission n. 传输, 传送, transmit v. 传输, 转送, 传达, 传导 6. amplifier n.放大器,扩音器 amplify v. 扩大,放大,增强amplification n. 扩大,放大 7. oscillator n.振荡器 8. correlate v. 是相互关联 correlation n.相互关系, 相关(性) 9. transmitter n.发射机 transmit receive transmission reception (发射) (接收) 10.subsequent adj.随后的 课一B Capacitors 电容 1.capacitor n. 电容器 2.capacitance n. 电容量(值) Resistor resistance capacitor capacitance inductor inductance 3. fixed adj. 固定的 variable adj. 可变的 4. dielectric n. 电介质,绝缘材料 adj. 绝缘的 5. relatively adv. 相对地 absolutely adv.绝对地 6. maximum adj. 最大的 n. 最大值 minimum adj. 最小的 n. 最小值 7. farad n. 法(拉) F ohm n. 欧姆Ω Henry n. 亨(利)H 8. trimmer n. 调整者, 整理者, 9. screwdriver n. 螺丝起子,改锥课二A Radio T ransmitter无线电发射机 1. radio transmitter 无线电发射机 radio n. 无线电,无线 2. telecommunication n.电信,电信学, 无线电通信 telephone n.电话,电话机 telegraph n.电报, 电报机, 电讯报 3. transmit v. 传输, 转送, 传达, 传导, 发射, 发报 transmit receive transmission reception transmitter receiv er (发射) (接收) 4. intelligence n.信息、情报、智能 information/message n.信息 5. potential adj.潜在的, 可能的, 势 的, n.潜能, 潜力, 电位 6. generate v.产生,发生 generation n.产生, 发生, 一代,7. frequency n.频 low frequency 几个Hz到几十kHz high frequency 几个MHz到几十 MHz radio frequency 几百MHz到几 个GHz 8. pulse signal 脉冲信号 9. wavelength n.波长用λ表示 10. output n.输出,产量 input n.输入 11. band n. 带,波段,频带 课二B Electromotive Force 电动势 1. electromotive adj.电动的,电动 势的 electromotive force 电动势 2.driving adj.驱动的 driving force n. 驱动力 driving unit 传动装置 3. volt n. 伏特 4. distinguish v.区分 5. potential difference 电位差 课三A Time Constant 时常数 1.nuclear adj.原子能的, n.核武器, 有核国 nuclear arms 核武 nuclear energy 核能 2.constant n.常数 adj.不断, 不断的, time constant 时间常数 3. instantaneously adv.瞬间地,即刻 instant n.瞬息, 一会儿, 时刻 4. dependent adj. 依赖的,依赖于,取决于 5. capacitiv e adj.电容的,容性的 capacitor n.电容器 capacitance n.电容值 6.discharge n.放电v.放电 charge n.电荷,充电v.充电 7.universal 普遍的, 全体的, 通用的, 课三B RL Time Constant RL时序常数 1.inductor n.电感器 inductance n.电感值(量) inductive adj.感应的; 电感的 2. function n.功能, 函数,作用, 3. Decay n.衰减v. 衰减 decay constant 衰减常数 decay factor 衰减因子 4. reverse adj.反向的, 相反, 逆转的 5. peak value 峰值

电子专业中英文词汇翻译

电子专业词汇的中英文对照 电路的基本概念及定律 电源source 电压源voltage source 电流源current source 理想电压源ideal voltage source 理想电流源ideal current source 伏安特性volt-ampere characteristic 电动势electromotive force 电压voltage 电流current 电位potential 电位差potential difference 欧姆Ohm 伏特Volt 安培Ampere 瓦特Watt 焦耳Joule 电路circuit 电路元件circuit element 电阻resistance 电阻器resistor 电感inductance 电感器inductor 电容capacitance 电容器capacitor 电路模型circuit model 参考方向reference direction 参考电位reference potential 欧姆定律Ohm’s law 基尔霍夫定律Kirchhoff’s law 基尔霍夫电压定律Kirchhoff’s voltage law(KVL)基尔霍夫电流定律Kirchhoff’s current law(KCL) 结点node 支路branch 回路loop 网孔mesh 支路电流法branch current analysis 网孔电流法mesh current analysis 结点电位法node voltage analysis 电源变换source transformations 叠加原理superposition theorem 网络network 无源二端网络passive two-terminal network 有源二端网络active two-terminal network 戴维宁定理Thevenin’s theorem 诺顿定理Norton’s theorem 开路(断路)open circuit 短路short circuit 开路电压open-circuit voltage 短路电流short-circuit current 交流电路 直流电路direct current circuit (dc)交流电路alternating current circuit (ac) 正弦交流电路sinusoidal a-c circuit 平均值average value 有效值effective value 均方根值root-mean-squire value (rms) 瞬时值instantaneous value 电抗reactance 感抗inductive reactance

电子信息工程专业英语 课文翻译 Unit 12 译文

Unit 12 生物识别技术 Unit 12-1 第一部分:指纹识别 在所有的生物技术中,指纹识别是最早期的一种技术。我们知道,每个人都有自己独特的、不可变更的指纹。指纹是由手指表皮上的一系列峰谷组成的。指纹的独特性是由这些峰谷的形状以及指纹的细节点所决定的。指纹的细节点是指纹局部凸起处的一些特性,这些特性出现在凸起的分叉处或是凸起的截止处。 指纹匹配技术可以被分为两类:基于细节的指纹匹配技术和基于相关性的指纹匹配技术。基于细节的指纹匹配首先要找出细节点,然后在手指上对应出与它们相关的位置,如图12.1所示。但是,使用这种方法存在一些困难。要精确地提取指纹的细节点是很困难的。而且,这种方法不能很好地考虑指纹峰谷的整体形状。基于相关性的指纹匹配技术可以解决部分基于细节的指纹匹配方法存在的问题,但它也存在一些自身的缺陷。基于相关性的匹配技术需要给出已注册过的特征点的精确位置,并且该方法会受图像平移和旋转的影响。 图12.1 基于细节的指纹匹配 基于细节的指纹匹配技术在匹配不同大小的细节模型时(未注册过的)会存在一些问题。指纹上局部的凸起结构不能完全由指纹细节实现特征化。我们可以尝试另一种表达指纹的方法,它可以获得更多的指纹局部信息并且得到固定长度的指纹编码。于是,我们只需要计算两个指纹编码之间的欧几里得距离,匹配过程有望变得相对简单。 研发对于指纹图像中噪声更稳健并能实时提供更高精度的算法是重要的。商用指纹(身份)认证系统对给定的错误接受率要求具有很低的错误拒绝率。在这点上,任何一项简单的技术都很难实现。我们可以从不同的匹配技术中汇总多个证据从而提高系统的总体精确度。在实际应用中,传感器、采集系统、性能随时间的变化是关键因素。为了评价系统性能,我们有必要对少数使用者在一段时间内进行现场试验。 每天我们可以从法医鉴定、出入口控制、驾驶证登记等多个方面的应用中采集并保存大量的指纹。基于指纹的自动识别系统需要把输入的指纹与数据库中大量的指纹进行匹配验证。为了缩短搜索时间、降低计算复杂度,要以准确而一致的方式将这些指纹分类,从而使输入的指纹只需与数据库某一子集中的指纹进行比对。 指纹分类是将指纹划分入多个预定义指纹类型中的一类中的一项技术。这些预定义的指纹类型是由提供索引机制的文献建立的。图12.2表示了不同类型的指纹。它们有螺纹状的、右旋状的、左旋状的、弓形的、帐篷形的。输入指纹首先粗略地被匹配为预定义的类型中的一类,随后,输入指纹仅与这一大类指纹库中的子集作更精细的比较。 图12.2 不同类型的指纹 指纹自动匹配中关键的一步是自动并且可靠地从输入指纹图像中提取出细节。然而,细节提取算法的好坏很大程度上依赖于输入图像质量的好坏。为确保自动指纹识别或确认系统的性能对于不同指纹图像质量具有稳健性,必须在细节提取模块中加入指纹增强算法。快速指纹增强算法能根据对局部指纹脊方向和频率(密度)的估计自适应地改善输入指纹图像中脊和沟结构的清晰度,如图12.3所示。实验证明加入增强算法可以显著增强指纹认证的精度。 图12.3 指纹增强 Unit 12-2 第二部分:说话人辨认介绍 介绍 现代安全系统范围很广, 通常要通过多层系统才能完全被突破。除了标准的锁和警报系统以外,还有很复杂的方法来保护重要资料。其中多数的方法为可以允许或者不允许一个特定人员获取资料——计算机系统必须能够检测出指纹、读取个人眼孔图样、或者确定说话者的真实身份。最后一点是本文讨论的重点——说话人辨认。说话人辨认经常会与其他类似的术语混淆。以下对这些术语的精确定义做出解释。 说话人识别:确定是谁在说话。 说话人辨认:初始情况下不知道说话人是谁,必须在与模板比较后确定说话人的身份。通常会有很多相关的模板。 说话人确认:确定说话者是否就是他(她)自称的那个人。仅将说话者的话音与一个样板进行比对,即他(她)自称的那一个。 语音识别:识别出人们说话时的语句。换句话说,识别出一个人在说什么而不是谁在说话。这个术语经常与声音识别相混淆。声音识别是识别出说话人。

电子信息工程专业英语词汇(精华整理版)

transistor n 晶体管 diode n 二极管semiconductor n 半导体 resistor n 电阻器 capacitor n 电容器 alternating adj 交互的 amplifier n 扩音器,放大器integrated circuit 集成电路 linear time invariant systems 线性时不变系统voltage n 电压,伏特数 tolerance n 公差;宽容;容忍condenser n 电容器;冷凝器dielectric n 绝缘体;电解质electromagnetic adj 电磁的 adj 非传导性的 deflection n偏斜;偏转;偏差 linear device 线性器件 the insulation resistance 绝缘电阻 anode n 阳极,正极 cathode n 阴极 breakdown n 故障;崩溃 terminal n 终点站;终端,接线端emitter n 发射器 collect v 收集,集聚,集中insulator n 绝缘体,绝热器oscilloscope n 示波镜;示波器 gain n 增益,放大倍数 forward biased 正向偏置 reverse biased 反向偏置 P-N junction PN结 MOS(metal-oxide semiconductor)金属氧化物半导体 enhancement and exhausted 增强型和耗尽型 integrated circuits 集成电路 analog n 模拟 digital adj 数字的,数位的horizontal adj, 水平的,地平线的vertical adj 垂直的,顶点的amplitude n 振幅,广阔,丰富attenuation n衰减;变薄;稀薄化multimeter n 万用表 frequency n 频率,周率 the cathode-ray tube 阴极射线管 dual-trace oscilloscope 双踪示波器 signal generating device 信号发生器 peak-to-peak output voltage 输出电压峰峰值sine wave 正弦波 triangle wave 三角波 square wave 方波 amplifier 放大器,扩音器 oscillator n 振荡器 feedback n 反馈,回应 phase n 相,阶段,状态 filter n 滤波器,过滤器 rectifier n整流器;纠正者 band-stop filter 带阻滤波器 band-pass filter 带通滤波器 decimal adj 十进制的,小数的hexadecimal adj/n十六进制的 binary adj 二进制的;二元的octal adj 八进制的 domain n 域;领域 code n代码,密码,编码v编码 the Fourier transform 傅里叶变换 Fast Fourier Transform 快速傅里叶变换microcontroller n 微处理器;微控制器assembly language instrucions n 汇编语言指令 chip n 芯片,碎片 modular adj 模块化的;模数的 sensor n 传感器 plug vt堵,塞,插上n塞子,插头,插销coaxial adj 同轴的,共轴的 fiber n 光纤relay contact 继电接触器 single instruction programmer 单指令编程器 dedicated manufactures programming unit 专 供制造厂用的编程单元 beam n (光线的)束,柱,梁 polarize v(使)偏振,(使)极化 Cathode Ray Tube(CRT)阴极射线管 neuron n神经元;神经细胞 fuzzy adj 模糊的 Artificial Intelligence Shell 人工智能外壳程序 Expert Systems 专家系统 Artificial Intelligence 人工智能 Perceptive Systems 感知系统 neural network 神经网络 fuzzy logic 模糊逻辑 intelligent agent 智能代理 electromagnetic adj 电磁的 coaxial adj 同轴的,共轴的 microwave n 微波 charge v充电,使充电 insulator n 绝缘体,绝缘物 nonconductive adj非导体的,绝缘的 antenna n天线;触角 modeling n建模,造型 simulation n 仿真;模拟 prototype n 原型 array n 排队,编队 vector n 向量,矢量 wavelet n 微波,小浪 sine 正弦cosine 余弦 inverse adj倒转的,反转的n反面;相反v 倒转 high-performance 高精确性,高性能 two-dimensional 二维的;缺乏深度的 three-dimensional 三维的;立体的;真实的 object-oriented programming面向对象的程序 设计 spectral adj 光谱的 attenuation n衰减;变薄;稀释 distortion n 失真,扭曲,变形 wavelength n 波长 refractive adj 折射的 ATM 异步传输模式Asynchronous Transfer Mode ADSL非对称用户数字线Asymmetric digital subscriber line VDSL甚高速数字用户线very high data rate digital subscriber line HDSL高速数据用户线high rate digital subscriber line FDMA频分多址(Frequency Division Multiple Access) TDMA时分多址(Time Division Multiple Access) CDMA同步码分多址方式(Code Division Multiple Access) WCDMA宽带码分多址移动通信系统(Wideband Code Division Multiple Access) TD-SCDMA(Time Division Synchronous Code Division Multiple Access)时分同步码分多址 SDLC(synchronous data link control)同步数据 链路控制 HDLC(high-level data link control)高级数据链路 控制 IP/TCP(internet protocol /transfer Control Protocol)网络传输控制协议 ITU (International Telecommunication Union) 国际电信联盟 ISO国际标准化组织(International Standardization Organization); OSI开放式系统互联参考模型(Open System Interconnect) GSM全球移动通信系统(Global System for Mobile Communications) GPRS通用分组无线业务(General Packet Radio Service) FDD(frequency division duplex)频分双工 TDD(time division duplex)时分双工 VPI虚路径标识符(Virtual Path Identifier); ISDN(Integrated Services Digital Network)综 合业务数字网 IDN综合数字网(integrated digital network) HDTV (high definition television)高清晰度电视 DCT(Discrete Cosine Transform)离散余弦变换 VCI(virtual circuit address)虚通路标识 MAN城域网Metropolitan area networks LAN局域网local area network WAN广域网wide area network 同步时分复用STDM Synchronous Time Division Multiplexing 统计时分复用STDM Statistical Time Division Multiplexing 单工传输simplex transmission 半双工传输half-duplex transmission 全双工传输full-duplex transmission 交换矩阵Switching Matrix 电路交换circuit switching 分组交换packet switching 报文交换message switching 奇偶校验parity checking 循环冗余校验CRC Cyclic Redundancy Check 虚过滤Virtual filter 数字滤波digital filtering 伪随机比特Quasi Random Bit 带宽分配Bandwidth allocation 信源information source 信宿destination 数字化digitalize 数字传输技术Digital transmission technology 灰度图像Grey scale images 灰度级Grey scale level 幅度谱Magnitude spectrum 相位谱Phase spectrum 频谱frequency spectrum 智能设备Smart Device 软切换Soft handover 硬切换Hard Handover 相干检测Coherent detection 边缘检测Edge detection 冲突检测collision detection 业务集合service integration 业务分离/综合service separation/ integration 网络集合network integration 环形网Ring networks 令牌环网Token Ring network 网络终端Network Terminal 用户终端user terminal 用户电路line circuit 电路利用率channel utilization(通道利用率) 相关性coherence 相干解调coherent demodulation 数字图像压缩digital image compression 图像编码image encoding 有损/无损压缩lossy/lossless compression 解压decompression 呼叫控制Call Control 误差控制error control 存储程序控制stored program control 存储转发方式store-and-forward manner 语音\视频传输voice\video transmission 视频点播video-on-demand(VOD) 会议电视Video Conference 有线电视cable television 量化quantization 吞吐量throughput 话务量traffic 多径分集Multipath diversity 多媒体通信MDM Multimedia Communication 多址干扰Multiple Access Interference 人机交互man machine interface 交互式会话Conversational interaction

相关主题