机务常用工具中英文对照

机务常用工具中英文对照
扳手Wrenches/套筒Sockets
开口扳手 Open End Wrenches
梅花扳手 Spline End Wrenches
块扳手 Crowfoot Wrenches
开口/梅花扳手 Combination Wrenches
内六角扳手 Hex Wrenches
平板棘轮扳手 Slab Ratchet
棘轮扳手 Ratchet Wrenches
力矩扳手 Torque Wrenches
管钳 Pipe Wrenches
活动扳手 Adjustable Wrenches
六角套筒 Six Point Sockets
梅花套筒 Twelve Point Sockets
万向套筒 Universal Sockets
转接头 Adaptor
套筒接杆 Socket Extension
万向转接头 Universal Joint
螺刀Screwdrivers
快速螺刀 Fast Screwdrivers
仪表螺刀 Electronic miniature Screwdrivers
十字头螺刀 PILLIPS Screwdrivers
磁性螺刀 Magnetic Screwdrivers
一字头螺刀 Flat Tip Screwdrivers
摇把 Speeders
钳Pliers
尖嘴钳 Needle Nose Pliers
大力钳 Locking Pliers
保险丝钳 Safety Wire Twisters
鹰嘴钳 Adjustable Joint Pliers
插头钳 Connector Plug
剥线钳 Wire Strippers
鱼口钳 Combination Slip-Joint Pliers
卡环钳 Convertible Snap Ring Pliers
剪线钳 Diagonal Cutters
压线钳 Wire Crimpers
电气工具Electronic Tools
矿灯 Safety Lamb (Miner’s Lamb)
手电 Flashing Light
对讲机 Interphone
电烙铁 Electronic Iron
耳机 Earphone
防静电手腕 Static Wrist
电池 Battery
充电器 Charger
扬声器 Speaker
电源插座 Receptacle
电枪 Electronic Runner
电钻 Electronic Drills
指挥棒 Flashing Emergency Light
超声波 Ultrasonic
测量工具Measuring Tools
钢板尺 Steel Rulers
卷尺 Tape Rulers
螺旋卡尺 Outside Micrometer
塞尺 Feeler (Thickness) Gauges
量杯 Measuring Cup
游标卡尺 Dial Caliper
表 Gauges
三用表 Multi Meter
兆欧表 Meg Ohm Meter
杂项Diversiform
反光镜 Inspection Mirror
放大镜 Magnifier
软杆双爪式机械手 Flexible Two_claw Pick Up Tool
软杆磁棒 Flexible Magnetic Pick Up Tool
划刀 Utility Knife
刮刀 Scraper Knife
剪刀 Snip (Scissor)
锯 Saw
凿子 Chisels
錾子 Punch
三脚架 Tripod (Spider)
铜榔头 Copper Hammer
铁榔头 Iron Hammer
胶榔头 Rubber Hammer
弯勾 Hook
锉 File
镊子 Nipper (Pliers)
销钉插拔工具 Pin Removal Tools
气枪 Pneumatic Runner
气钻 Pneumatic Drills
铆钉枪 Rivet Gun
注射器 Injector (Squirt)
滑油加油车 Oil Cart
液压油加油车 Hydraulic Fluid Cart
注油枪 Grease Gun
抹布 Dishcloth
手套 Glove
绳索 Rope
工具箱 Tools Kit
工具架 Tools Rack
千斤顶 Jack
撬棒 Tommy Bar
工作梯 Work Ladder
砂轮 Grinding wheel
砂纸 Sand paper
胶带 Adhesive Tape
焊锡 Soldering Tin
拖把 Tow Bar
发光背心 Flashing Vest
护目镜 Goggle (Blinkers)
安全带 Life Belt(Safety Belt)
增补
两用扳手CONBINATION SPANNER
两用扳手套装COMBINATION SPANNER SET
加长型两用扳手COMBINATION SPANNER EXTRA LONG
梅花棘轮开口扳手OPEN ENDED SPANNER WITH RING RATCHET
梅花棘轮开口扳

手套装OPEN ENDED SPANNER WITH RING RATCHET SET
两用棘轮扳手COMBINATION RATCHET SPANNER
两用棘轮扳手套装COMBINATION RATCHET SPANNER SET
1/4'连接物ADAPTOR 1/4'
组合支架工具COMBINATION HOLDING TOOL
小型发光二极管MINIATURE LED LAMP
活动扳手SINGLE OPEN ENDED SPANNER
扳手套装MAGNETO SPANNER SET
单开口扳手/呆扳手SINGLE ENDED OPEN JAW SPANNER
双开口扳手DOUBLE OPEN ENDED SPANNER
双开口扳手套装DOUBLE OPEN ENDED SPANNER SET
扩口螺母扳手PLARE NUT SPANNER（OPEN）
半月型梅花扳手HALF-MOON RING SPANNER
双头梅花扳手（短）DOUBLE ENDED SPANNER（SHORT）
双头梅花扳手（长）DOUBLE ENDED SPANNER（LONG）
平头梅花扳手（直）FLAT RING SPANNER STRAIGHT PATTERN
开口敲击扳手OPEN ENDED SLOGGING SPANNER
梅花敲击扳手RING SLOGGING SPANNER
高颈梅花敲击扳手DEEP AFFSET RING SLOGGING SPANNER
直头梅花扳手DEEP RING SPANNER（STRAIGHT PATTERN）
延长管EXTENSION TUBE
爪型扳手CROWFOOT SPANNER
两用活头扳手COMBINATION SWIVEL HEAD WRENCH
活结T型扳手SWIVEL HANDLE WITH SLIDING T
套筒扳手SOCKET WRENCH
弯头套筒扳手ANGLED SOCKET WRENCH
双头套筒扳手DOUBLE ENDED SOCKET WRENCH
旋棒TOMMY BAR
分节旋棒STEPPED TOMMY BAR
3C把手套筒扳手SOCKET WRENCH WITH 3C-HANDLE
T型及磁性套筒扳手SOCKET WRENCH WITH T-HANDLE AND MAGNET
钩头扳手HOCK SPANNER WITH LUG
带销扳手PIN SPANNER
可调式两爪钩扳手CALIPER FACE SPANNER WITH ADJUSTABLE
1/4'标准六角套筒HEXAGON SOCKET
1/4'加长六角套筒HEXAGON LONG PATTERN SOCKET
棘轮扳手RATCHETS
套筒SOCKETS
套筒套装SOCKETS SETS
摩擦棘轮扳手FRICTION RATCHETS
冲击工具IMPACT TOOLS
旋具头BITS
扭矩扳手TORQUE WRENCHES
1/4梅花套筒SOCKET UD PROFILE
1/4六角套筒
星型套筒SOCKET FOR PROTRUDING HEAD SCREWS
1/4一字，十字，星型，内六角旋具套筒
1/4’双向棘轮套筒扳手1/4’REVERSIBLE RATCHET
T柄棘轮扳手RATCHET WITH T-HANDLE
手用棘轮头HAND RATCHET WITHOUT HANDLE
1/4转3/8转换接头CONVERTER 1/4 TO 3/8
T型滑动头手柄TOMMY BAR WITH SLIDING T
活动延长杆FLEXIBLE EXTENSION
通用延长杆UNIVERSAL-JOINT EXTENSION
1/4四方驱动连接头SQUARE-DRIVE COUPLER
1/4万向接头UNIVERSAL JOINT
活动头手柄SWIVEL HANDLE
套筒固定夹SOCKET RAIL WITH MAGNETIC
3/8一字，十字，星型，内六角旋具套筒
3/8六角套筒SOCKET HEXAGON 3/8
3/8梅花套筒SOCKET UD PROFILE
塑料棘轮扳手PLASTIC RATCHET
旋具头接头BIT ADAPTOR
旋具头棘轮扳手BIT RATCHET
旋具头螺丝起子BIT SCREWDRIVER
旋具头延长杆BIT EXTENSION
旋具头SCREWDRIVER BITS
风动套筒IMPACT SOCKET
风动套筒附件ACCESSORIES FOR IMPACT SOCKET
手动操作冲击手柄HAND-OPERATED INPACT DRIVER
摩擦式梅花棘轮扳手FRICTION TYPE RATCHET WITH RING WITH BI-HEXAGON
摩擦式四方棘轮扳手FRICTION TYPE RATCHET WITH SQUARE RING
安装扳手/

尖尾扳手CONSTRUCTION RATCHET BI-HEXAGON
0.6-5.4NM扭力螺丝起子TORQUE SCREWDRIVER HANDLE 0.6-5.4NM
3C一字螺丝起子3C-SCREWDRIVER FOR SLOTTED HEAD SCREWS
3C十字PH螺丝起子3C-SCREWDRIVER FOR CRUCIFORM HEAD PH
3C米字螺丝起子
3C星型螺丝起子
3C球头六角螺丝起子
5件/6件/7件/155件螺丝起子套装SET FOR HEAD SCREWS
电工螺丝旗子ELECTRONIC SCREWDRIVER
木柄螺丝起子SCREWDRIVERS WITH WOODEN HANDLE
磁化/消磁器MAGNETIZER AND DEMAGNETIZER
方刃锥子SQUARE BLADED AWL
T型六角螺丝起子HEXAGON SCREWDRIVER WITH T-HANDLE
T型内六角扳手HEXAGON SOCKET KEY WITH T-HANDLE
内六角扳手HEXAGON SOCKET KEY
加长内六角扳手EXTRA LONG HEXAGON SOCKET KEY
加长球头内六角扳手
内六角扳手套装HEXAGON SOCKET KEY SET
T型星形螺丝起子SCREWDRIVER WITH T-HANDLE
曲柄螺丝起子CRANKED SCREWDRIVER
量规GARGE
车灯测电笔CAR LIGHT TESTER
6-24伏测电笔VOLTAGE TESTER 6-24V
150-250伏测电笔VOLTAGE TESTER 150-250V
钳子3件套装PLIERS SET，3-PIECE
万能手钳48件套UNIVERSAL PLIERS ASSORTMENT WITH 48 PIECE
小钢丝钳SMALL COMBINATION PLIERS
钢丝钳（德式）COMBINATION PLIERS（GERMAN PATTERN）
钢丝钳（欧式）COMBINATION PLIERS（EURO PATTERN）
强力钢丝钳POWER COMBINATION PLIERS
塑料水口钳SIDE CUTTERS FOR PLACTIC
剪钳（瑞典款式）SIDE CUTTERS（SWEDISH PATTERN）
电工剪钳ELECTRICIAN’S SIDE CUTTERS
剪钳（美国款式）POWER SIDE CUTTERS（AMERICAN PATTERN）
杠杆剪钳LEVER-ACTION SIDE CUTTERS
杠杆顶剪钳LEVER-ACTION END CUTTING NIPPERS
核头钳TOWER PINCERS
拨钉钳PINCERS
平头钳FLAT NOSE PLIERS
圆头钳ROUND NOSE PLIERS
直头尖嘴钳LONG NOSE PLIERS
弯头尖嘴钳
电话钳TELEPHONE PLIERS
强力尖嘴钳TRIPLE-FUNCTION PLIERS
直口机修工钳MECHANICS PLIERS STRAIGHT PATTERN
曲口机修工钳MECHANICS PLIER ANGLED PATTERN
偏口机修工钳MECHANICS PLIER OFFSET PATTERN
30度平圆机修钳MECHANICS PLIER WITH 30
电缆刀CABLE KNIFE
电工电缆刀ELECTRICIAN’S CABLE KNIFE
防静电专用钳子
电子钳ELECTRONIC PLIERS
迷你电子钳MINIATURE ELECTRONIC PLIERS
防静电尖嘴钳/防静电顶切钳/电子平头钳/电子剪钳/防静电剪钳/电子剥线钳
电缆剪钳CABLE CUTTERS
小型万用剪SMALL UNIVERSAL SCISSORS
万用电缆刀UNIVERSAL CABLE KNIFE
自动剥线钳STRIPPING PLIERS ANTOMATIC
剥线钳STRIPPING PLIERS
固定剥线钳STRIP-FIX STRIPPING PLIERS
剥线工具WIRE STRIPPER
高效剥线钳HIGH-PERFORMANCE WIRE STRIPPER
数据传输电缆精确剥线钳PRECISION WIRE STRIPPER FOR DATA CABLES
同轴电缆剥线钳WIRE STRIPPER FOR COAXIAL CABLES
绝缘剥漆钳INSULATING VARNISH STRIPPER
剥线刀WIRE STRIPPING KNIFE
绝缘胶带INSULATING TAPE
压线钳CRIMPING PLIERS
锁把式压线钳LOCK-GRIP CRIMPING PLIERS
端子压线钳WIRE END-SLEEVE PLIERS
模块压线夹钳MODULAR LOCK-GRIP CRIMPING PLIERS
模块压线钳MODULAR CRIMP

ING PLIERS
精确压线钳PRECISION CRIMPING PLIERS
外卡簧钳（轴用）EXTERNAL CIRCLIP PLIERS（ON SHAFTS）
直头/弯头外卡簧钳（轴用）
内卡簧钳（孔用）INTERNAL CIRCLIP PLIERS（IN BORES）
直头/弯头内卡簧钳（孔用）
大型/重型卡簧钳
X型把X-GRIP
大力钳LOCK-GRIP PLIERS
平行钳夹大力钳PARALLEL JAW LOCK-GRIP PLIERS
宽口大力钳WIDE JAW LOCKING PLIERS
滑行杆式大力钳LOCK-GRIP SLIDE CLAMP
固定大力钳GRIP WRENCH FOR GLUEING
机械工作台钳MACHINE WORKBENCH CLAMP
焊接大力钳LOCK-GRIP WELDING CLAMP
管子焊接大力钳LOCK-GRIP TUBE WELDING CLAMP
C型大力钳LOCK-GRIP C CLAMP
水泵钳UNIVERSAL PLIERS（7种设置/5种设置）
水泵钳WATER PUMP PLIERS
特殊水泵钳SPECIAL WATER PUMP PLIERS
可调式高速管子钳HIGH-SPEED PIPE WRENCH WITH SCREW ADJUSTER
高速曲口管子钳HIGH-SPEED PIPE WRENCH CURVED
迷你链式管子钳MINI CHAIN PIPE WRENCH
链钳CHANIN PIPE WRENCH
重型管子钳STILLSON PIPE WRENCH
断线钳BOLT CUTTERS
钳子套装（3件/4件/6件/8件）
VDE绝缘安全电工工具VDE INSULATED SAFETY TOOLS
VDE绝缘标准符合DIN EN 60900 IEC 60900：2004以及VDE680 适合在高压区安全工作（AC1000V DC1500V）
VDE绝缘螺丝起子VDE SCREWDRIVER（一字/十字/米字/星型/内六角）
VDE绝缘起子套装
电压传感器/电压测试器VOLTAGE DETECTOR/TESTER
绝缘扭力扳手VDE TORQUE WRENCH
绝缘双向棘轮扳手VDE REVERSIBLE RATCHET
绝缘六角套筒VDE SOCKET HEXAGONAL
绝缘旋具头套筒VDE SCREWDRIVER BIT SLCKET
T型绝缘扳手VDE T-HANDLE
绝缘延长杆VDE EXTENSION
绝缘电工工具组套（3件/8件/14件/108件）
VED 3C绝缘手柄套筒扳手VDE SOCKET WRENCH WITH 3C HANDLE
绝缘梅花扳手VDE SINGLE-ENDED RING SPANNER WITH DEEP OFFSET
绝缘开口扳手VDE SINGLE-ENDED OPEN SPANNER
VDE绝缘钢锯HACKSAW
绝缘电缆刀VDE CABLE KNIFE
绝缘电缆剪CABLE SHEARS
棘轮式绝缘电缆剪钳CABLE CUTTERS
VDE绝缘电缆剪VDE CABLE SHEARS
绝缘剥线钳/绝缘固定剥线钳/绝缘水泵钳/绝缘强力钢丝钳/绝缘斜口钳/绝缘电工斜口钳/绝缘平口钳/绝缘圆头钳/绝缘直头尖嘴钳/绝缘弯头尖嘴钳
VDE绝缘橡胶垫VDE RUBBER COVER SHEET
VDE绝缘电工安全手套VDE ELECTRICIANS’S SAFETY GLOVES
绝缘塑料夹VDE PLASTIC CLAMPS
车轮扳手WHEEL WRENCHES
十字扳手4 WAY WHEEL WRENCH
撬棒TYRE LEVER
轮毂罩移除工具HUBCAP RENOVING TOOS
配重钳BALANCE-WEINHT PLIERS
制动弹簧钳BRAKE-SPRING PLIERS
闸线弹簧钳PLIERS FOR BRAKE-CABLE SPRINGS
制动钳刷BRAKE-CALIPER BRUSH
放油塞扳手（四方）DRAIN-PLUG WRENCH WITH SQUARE
油壶OIL CANS
过滤器扳手UNIVERSAL FILTER WRENCH
皮带钳PULLEY WRENCH
阀门研磨机VALVE GRUNDER
阀门研磨工具VALVE LAPPING TOOS
油封钳VALVE-SEAL PLIERS GUNMETAL FINISH
汽缸/活塞环压缩器VALVE SPRING COMPRESSOR BRIGHT NICKEL-PLATDE
活塞环钳PISTON RING PLIERS
软

管夹钳HOSE CLIP PLIERS
电极拉马BATTERY TERMINAL PULLER
电池测试器BATTERY TESTER
火花塞套筒SPARK PLUG SOCKET
火花塞套筒扳手SPARK PLUG SOCKET WRENCH
火花塞刷SPARK-PLUG BRUSH
特殊尖冲凿SPECIAL PIN PUNCH
弹簧撑开器SPRING SPREADER
球头拉拔器UNIVERSAL BALL JOINT REMOVER
通用罐UMIVERSAL CANISTER
防冻测试器ANTI-FREEZE TESTER
安装钳INSTALLATION PLIERS
吸盘SUCTION LIFTER
磁性拾取工具MAGNETIC PICK-UP TOOL
金属片切割器NIBBER
杠杆剪切机LEVER-ACTION TIN SNIPS
打孔钳PUNCH PLIERS
橡胶锤RUBBER HAMMER
塑料锤PLASTIC HAMMER
无后坐力锤RECOILLESS HAMMER
钳工球头锤ENGINEERS’S BALL PEIN HAMMER
钳工锤ENGINEERS’S HAMMER
平面刮刀FLAT SCRAPER
三角空心刮刀THREE-EDGED HOLLOW-GROUND SCRAPER
三角实心刮刀THREE-EDGED FLAT-GROUND SCRAPER
密封刮刀GASKET SCRAPER
平锉HAND FILE
圆锉ROUND FILE
三角锉TRIANGULAR FILE
半圆锉HALF-ROUND FILE
锉类6件套装
中心冲/凿/开口销冲CENTRE PUNCHES/CHISELS/DRIFT PUNCHES
钢锯HACKSAW
栓孔锯KEYHOLE SAW
小金属锯SMALL METAL SAW
小PUK钢锯PUK JUNIOR HACKSAW
HOBBY锯
台钳/台虎钳METALWORKING VICE（100/125/150mm）
钢卷尺STEEL TAPE MEASURE（3米/5米/8米）
阀塞尺VALVE FEELER GAUGE
塞尺
火花塞塞尺SPARK PLUG GAUGE
螺纹规THREAD GAUGE
游标卡尺POCKET VERNIER CALLIPER
数显游标卡尺DIGITAL CALLIPER
划线器SCRIBER
镊子TWEEZERS
十字镊子CROSSLOCK TWEEZERS
螺钉取出器BOLT EXTRACTOR
断螺钉取出器套装SCREW EXTRACTOR SET
机械螺母破开器MECHANICAL NUT SPLITTER
螺栓插入及取出器STUD INSERTER AND EXTRACTOR
丝锥THREAD FILE
管子割刀PIPE CUTTER
自动切割机AUTOMATIC PIPE CUTTER
链式切管机CHAIN PIPE CUTTER
虹吸扳手SIPHON TRAP PLIERS
钢丝刷WIRE BRUSH
锉刀清洁刷FILE CLEANING BRUSH
裁缝剪TAILORS SCISSORS
发光二极管井下检查灯LED INSPECTION LAMP
井下检查灯INSPECTION LAMP
发光二极管工作灯LED WORK LIGHT
工程锤ENGINEERS HAMMER ROTBAND-PLUS
工程圆头锤ENGINEERS’BALL PEIN HAMMER
胡桃木备用手柄SPARE HANDLE HICKORY
工匠锤JOINERS’HAMMER ROTBAND-PLUS
石匠锤CLUB HAMMER
双面石匠锤DOUBLE FACED CLUB HAMMER ROTBAND-PLUS
大锤SLEDGE HAMMER
大碎石锤STONE SLEDGE HAMMER
劈木锤WOOD SPLITTING HAMMER
铺路锤PAVING HAMMER
单板锤VENEER HAMMER
磁性锤MAGNETIC HAMMER ROTBAND
玻璃装配工锤GLAZIERS HAMMER
炭化合金瓦锤CARBIDE TILE HAMMER
羊角锤CLAW HAMMER
电焊敲锤SCALING HAMMER ROTBAND-PLUS
无弹力安全锤RECOILLESS HAMMER
安全锤SAFETY HAMMER SOFT-PLUS
塑料锤PLASTIC HAMMER
橡皮锤RUBBER MALLET HARD
尼龙锤NYLON HAMMER
木锤WOOLEN MALLET
铜锤COPPER HAMMER CLUB SHAPE
铝锤ALUMINIUM HAMMER ROTBAND
桶形铝锤LEAD HAMMER SARREL SHAPE
冷凿锤COLD CHISEL HAMMER
热凿锤HOT CHISEL HAMMER
平底压摸锤SET HAMMER TOP PART
压槽铁锤TOP FULLER
上型模锤BOTTOM FULLER
冲锤PUNCH HAM

MER
镰刀锤SCYTHE HAMMER
锻工钳BLACKSMITH’S TONGS
铆钉钳RIVETTING TONGS
锥型冲子/中心冲子/销式冲子DRIFT PUNCHES/CENTRE PUNCHES/PIN PUNCHES
自动中心冲子AUTOMATIC CENTRE PUNCH WITH TIP
冲子组套DRIFT PUNCH SET
铆钉装配器RIVET SETTER
字母及数字冲子LETTER AND NUMBER PUNCHES
装配冲子SETTING PUNCH
撬杆PRVBAR
起钉器NAIL FIFER OCTAGONAL
撬棍CROWBAR
通用拉马UNIVERSAL PULLER
两爪拉马PULLER 2-ARM PATTERN
三爪拉马PULLER 3-ARM PATTERN
防腐蚀拉马COROSTOP PULLER PATTERN
快速拉马QUICK-ACTION PULLER
两爪液压拉马UNIVERSAL 2-ARM PULLER
拉马延长杆EXTENSION FOR PULLERS
液压轴杆HYDRAULIC PRESSURE SPINDLE
三爪液压拉马UNIVERSAL 2-ARM PULLER
拉马套装PULLER SET
螺母劈开器NUT SPLITTER
液压螺母劈开器NUT SPLITTER HYDRAULIC
螺栓提取器STUD EXTRACTOR
轴承提取器BALL BEARING EXTRACTOR
滚珠轴承提取器套装BALL BEARING EXTRACTOR SET
内提取器INTERNAL EXTRACTOR
冲击轴承拉马IMPACT BEARING PULLER
汽缸拉马CYLINDER LINER PULLER COMPLETE WITH SUPPORT BRACE
分离拉马SEPARATOR PULLER
轴承分离器BEARING SEPARATOR
传动轴轴承拉马DRIVE SHAFT BEARING PULLER
分离器及拉马套装SEPARATOR AND PULLER SET
拉拔卡盘PULLING CHUCK
液压泵HYDRAULIC PUMP
液压手泵HYDRAULIC HAND PUMP
液压工具拉马1.50 PULLER FOR HUDRAULIC IMPLEMENT1.50
液压增力器HYDRAULIC PRESS
轮毂拉马WHEEL-HUB PULLER
传动轴拉马DRIVE-SHAFT PULLER
方向盘拉马STEERING-WHEEL PULLER
装配叉DISMANTLING AND ASSEMBLY FORK
球头拉拔器BALL JOINT PULLER
三爪机滤扳手OIL FILTER HOOK
弹簧撑SPRING SPREADER
塑料轴承安装套装PROFESSINAL PLASTIC BEARING INSTALLATION SET
法兰分离器FLANGE SEPARATORS
轨距测量器TRACK ALIGNMENT GAUGE
扳手WRENCHES
管子切割器PIPE CUTTERS
扩口工具FLARING TOOLS
弯管机PIPE BENDERS
管子工具PLUMBING TOOLS
铁皮剪/断线钳TIN SNIPS/BOLT CUTTERS
管子清洁设备PIPE CLEANING EQUIPMENT
弯管系统PIPE BENDING SYSTEMS
SNAP管道扳手PIPE WRENCH ECK-SNAP
钢管切割器PIPE CUTTER TUBEX FOR STEEL PIPES
生铁管切割器PIPE CUTTER TUBEX FOR CAST IRON PIPES
不锈钢管切割器RATCHET PIPE CUTTER NIRO FOR STAINLESS STEEL PIPES
管子修边器PIPE DEBURRING REAMER
不锈钢管修边器PIPE DEBURRING REAMER FOR STAINLESS STEEL PIPES
扩口工具套装FLARING TOOL SET BOERDEX
钢管扩口钳EXPANDER PLIERS FOR COPPER PIPES
带滑轨的弯管机PIPE BENDER WITH SLIDE RAIL
带滚轴的弯管机PIPE BENDER WITH ROLLER
弯管钳PIPE BENDING PLIERS
带滑轨的弯管钳PIPE BENDING PLIERS WITH SLIDE RAIL
带滚轴的弯管钳PIPE BENDING PLIERS WITH ROLLER
手动弯管机MANUAL BENDING TOOL
液压弯管机HYDRAULIC PIPE BENDER
手动液压弯管机PIPE BENDING MACHINE FOR MANUAL HYDRAULIC OPERATION
电动液压弯管机PIPE BENDING MACHINE FOR ELECTRO HYDRAULIC OPERATION
管道矫直工具PIPE STRAIGHTENING TOOL
金属片弯

边钳SHEET METAL CRINPING PLIERS
折边钳SEAMING PLIERS
快速夹取扳手QUICK-CLAMP WRENCH
夹管钳GRIPPING PLIERS
分级扳手STEPPED KEY
复合分级扳手COMBINATION STEPPED KEY
铁皮剪TIN SNIPS /HOLE CUTTING SNIPS /PELICAN PATTERN SNIPS
断线钳BOLT CUTTER
管道清洁软轴FLEXIBLE PIPE CLEANING SHAFT
排水管清洁器DRAIN PIPE CLEANER
工作台几工作桌WORKBENCHES AND WORK TABLES
工具车TOOL TROLLEYS
工具柜TOOL CABINETS
车间推车WORKSHOP TROLLEYS
抽屉柜/箱DRAWER-CABINETS/BOXES
衣柜/工作服柜WARDROBES
矮橱LOWER CUPBOARD UNIT
图纸夹DRAWING HOLDER
电源面板PWER SUPPLY PANEL
防酸放腐蚀工作台面板
六边形工作台HEXAGONAL WORKBENCH
带抽屉工作台WORKBENCH WITH DRAWER CABINET
塑料抽屉插件PLASTIC DRAWER INSERT
工作桌推车WORKSHOP TABLE TROLIEYS
工作台WORKBENCH
带背板工作台
坚固推车TROUGH TROLLEY
平板车PLATFORM TROLLEY
带手柄平板车PLATFORM TROLLYE WITH HANDLE
维护推车SERVICE TROLLEY
带工具箱车间推车WORKSHOP TROLLEY WITH TOOL CHEST
工具箱TOOL CHEST
存放斗STORAGE TRAY
卷纸架PAPER ROLL HOLDER
垃圾桶WASTE BASKET
移动架写字板LECTERN WORKTOP
存储盒STORAGE BOXES
带门库架CUPBOARD WITH SHELVING WITH DOORS
开敞式壁板COMPLETE PANEL SYSTEM WITH SLOTTED PANELS
存物柜LOCKER WITH HINGED DOORS
滑门橱CUPBOARD WITH SLIDING DOORS
电脑柜COMPUTER CABINET
桌上设备DESK INSTALLATION
移动电脑架PC STAION MOBILE
电脑车间组合PC WORKPLACE COMBINATION
更衣室条凳CHANGING CUBICLE SEAT BENCH
安全橱SAFETY CUPBOARD
衣橱CLOTHES LOCKER
带凳子的衣橱CLOTHES LOCKER WITH SEAT BENCH
消防员衣橱FIREFIGHTER’S CUPBOARD
工具橱TOOL CABINET
移动式可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER MOBILE
固定可回收物品垃圾收集箱RECYCLING WASTE-COLLECTION CONTAINER STATIONARY
分类垃圾收集站WASTE-COLLECTION STATION CONTAINER
立式烟灰缸STAND ASHTRAY
OCHSENKOPF系列斧头
欧洲ILTIS型斧
制图用刮刀
专业伐木斧
快劈斧
抢险袖珍刀
CAROLUS特殊工具
KLANN汽车专用工具
弹簧压缩器
横杆球头拉拔器
轮轴拉马
液压手用压力器
轴衬提取器
发动机锁定工具套装
扭距测试仪及设备TORQUE TESTER AND EQUIPMENT
扭距倍增器TORQUE MULTIPLIERS
扭距角度指示器TORQUE ANGLE INDICATORS
特殊DREMO工具SPECIAL DREMO TOOLS
DREMOMETER系列扭力工具DREMOMETER TOOLS
扭距螺丝刀TORQUE SCREWDRIVERS
扭距扳手/扭力扳手TORQUE WRENCHES
电子扭距测试仪ELECTRONIC TORQUE TESTER
DKD校准遵守DKD准则3-7/3-8/DIN EN ISO 6789
RAHSOL DREMOTEC产品校准按照DIN EN ISO 6789标准
迷你型扭距扳手DREMOMETER MINI
DREMOMETER高强度铝合金扭距扳手 含：
DREMOMETER 1-12NM /10-100LBF.IN （塑料外表）
DREMOMETER 6-30NM /50-270LBF.IN
DREMOMETER 8-40NM /70-350LBF.IN
DREMOMETER 20-120NM /15-90LBF.FT
DREMOMETER 40-200NM /30-150LBF.FT
DREM

OMETER 50-300NM /35-220LBF.FT
DREMOMETER 80-360NM /60-260LBF.FT
DREMOMETER 110-550NM /80-405LBF.FT
DREMOMETER 140-760NM /105-560LBF.FT
DREMOMETER 520-1000NM /380-730LBF.FT
DREMOMETER 750-2000NM
DREMOMETER 1500-3000NM
DREMOMETER系列棘轮头RATCHET HEADS DREMOMTER
扭距限制接合器TORQUE LIMIT UNIT
转角仪TORQUE ANGLE INDICATOR
圆形插头式扭距扳手（覆盖范围8-1000NM）
开口扳子头OPEN END RTTING
梅花扳子头RING END RTTING
半开口梅花扳子头FLARED END FITTING
棘轮头RATCHET HEAD
四方头FIXED SQUARE HEAD
方形插头式扭距扳手（覆盖范围8-400NM）
开口插头RECTANGULAR OPEN END RTTING
梅花插头RECTANGULAR RING END RTTING
半开口梅花插头RECTANGULAR FLARED END RTTING
TORCOFIX系列带四方驱动的扭距扳手
TORCOFIX K扭距扳手（四方头）TORQUE WRENCH TORCOFIX K 含：
4549-01 1-5NM 1/4’方头
4549-02 2-25NM 1/4’方头
4549-05 5-50NM 3/8’方头
4550-10 10-100NM 1/2’方头
4550-20 20-200NM 1/2’方头
4550-30 60-300NM 1/2’方头
4550-40 75-400NM 1/2’方头
4550-55 100-550NM 3/4’方头
4550-75 140-750NM 3/4’方头
TORCOFIX K扭距扳手套装TORCOFIX K TORQUE WRENCH SET
TORCOFIX K快速旋转把手QUICK-TURN WITH T-GRIP TORCOFIX K
蘑菇头MUSHROOM HEAD
TORCOFIX Z扭距扳手（圆形插头）TORQUE WRENCH TORCOFIX Z
TORCOFIX SE扭距扳手（四方插头）TORQUE WRENCH TORCOFIX SE
TORCOFIX FS扭距扳手（可预设扭力值2-200NM）TORQUE WRENCH TORCOFIX FS
TORCOFIX UK扭距扳手TORCOFIX UK TORQUE WRENCH
TORCOFIX K扭距扳手TORCOFIX K TORQUE WRENCH
扭距螺丝刀/扭力螺丝起子TORQUE SCREWDRIVERS
FS型扭距螺丝刀 范围0.02-13.6NM
S型扭距螺丝刀 范围0.05-9NM
SP型扭距螺丝刀 范围10-500CNM
TSN预置扭距滑转扳手TSN SLIPPER QORQUE WRENCH 范围3-125NM
TBN折弯式扭距扳手TBN BREAKER QORQUE WRENCH 范围0.2-135NM
TSP预置扭距滑转扳手TSP SLIPPER QORQUE WRENCH 范围1-10NM
TSC预置扭距滑转扳手TSC SLIPPER QORQUE WRENCH 范围1-10NM
电线标示系统PLASTIC-TAG MARKING SYSTEM
刻度盘/表盘扭距扳手DIAL MEASUREMENT TORQUE WRENCHES
适用场合：测试 控制 维护工作应用环境
ADS 4 0.8-4NM 1/4’方头
ADS 12D 2.4-12NM 1/4’方头
ADS 25 5-25NM 3/8’方头
ADS 40 8-40NM 3/8’方头
BDS 80E 16-80NM 1/2’方头
BDS 200 40-200NM 1/2’方头
CDS 400S 80-400NM 3/4’方头
DDS 800S 160-800NM 3/4’方头
EDS 1400S 280-1400NM 1’方头
EDS 2000S 400-2000NM 1’方头
88型折弯式扭距扳手TYPE 88 BREAKER TORQUE WRENCH 范围100-1500NM
8800-01 3/4’方头 100-500NM
8800-02 3/4’方头 150-700NM
8800-03 3/4’方头 300-1000NM
8800-04 3/4’方头 700-1500NM
8800-06 圆形插头16mm 130-550NM
扭距倍增器/扭力放大器/齿轮减速器TORQUE MULTIPLIERS
在狭小的空间内获得巨大的扭距输出 型号不同范围含1000NM - 47500NM
比例有1：5 1：15 1：15.5 1：25 1：26 1：75 1：125等等
数字扭距扳手/数显扭力

扳手ELECTRONIC TORQUE WRENCH
E-TORC微处理器控制扭距扳手E-TORC ELECTRONIC TORQUE WRENCH
TORCOTRONIC数显扭距扳手TORCOTRONIC ELECTRONIC TORQUE WRENCH
电子扭距测试仪ELECTRONIC TORSIONS TORQUE TESTER E-TP
智能型电子扭距测试仪系列
E-TP ELECTRONIC TORSIONS TORQUE TESTER范围包括：0.5-1000NM的测试
扭距扳手测试架TORQUE WRENCH TEST FRAME
E-TP打印机E-TP PRINTER
E-TP固定架E-TP ADAPTER PLATE
E-TP转接器E-TP ADAPTOR
E-TP软件及数据线E-TP SOFTWARE INCL AND PC-CONNECTION CABLE
E-TP包装箱E-TP PLASTIC-CASE