模具名称中英对照
top view 俯视图
front view 前视图
side view 侧视图
plane view 平面图
contour 外型铣削
pocket 挖槽
flow line 罩一曲面
multisurf多重曲面
filter过滤
ellipse 椭圆
polar 极坐标
arc endpoints两点画弧
polygon 多边形
isometric 等角视图
zig zag 双向
one way 单向
spline 圆滑曲线
blend 顺接
guide pin 导针;边针;直边
support pin 拉杆;水口边
support pin collar 拉杆定位;水口边定位介子
tapped hold for eyebolt 吊模螺孔
thermal expansion coefficien热膨胀系数
welding rod 熔接棒
cavity plate; A bolster plate(holder material) 母模板 (A板), 前模板stripper plate活动板,推料板
core plate 公模板 (B板),后模板
spacer block 间隔板
ejector retainer plate 上顶针板
ejector plate 下顶针板
pin point gate system 小水口系统
side gate system 大水口系统
infrared-transmitter 红外线发射器
infrared-receiver红外线接受器
synthetic resin合成权脂
air blow gun(with nozzles&hose)气枪
spiral hose 螺旋形的;盘旋的
guide strip行位导轨
ejector rod斜坊
set screw固定螺丝
countersunk screw沉头螺丝
hex screws胚头螺丝
shoulder screw带肩螺丝
residual stress残余应力
tensile张力
electricity erode电蚀刻
ohm meter电阻表
tubular dowel管钉,销钉
abrasive stone 研磨石材
SPI Mold Finish Comparison Kit -----SPI模具拋光比照工具rolled热轧
forged 热锻
extrude 挤压
cold drawn 冷拉
corrosive plastics 防腐塑料
tough 硬度
anneal ----n.退火
service life 注塑寿命
high viscosity 粘度较高的
extension plug 延伸尾塞
angle plug 斜角尾塞
thermocouple connector 热电偶连结头
hydraulic system (注塑机的)油压系统
temperature control zone 温控区
barrel heating capacity 料筒加热能力
screw torque 螺杆力矩
screw speed 螺杆速度
screw stroke 螺杆行程
nozzle contact force 热嘴接触力
screw L/D ratio 螺杆长度/直径比例
theoretical shot volume理论的注射容量
clamp force合模力
lock force 锁模力
internal heated 内部加热
external heated 外部加热
heating rod 加热棒
air-gap insulation 空气隔绝层
spare part(accesory)备用件
insulating ring 绝缘圈
sealing washer 垃圾钉
adaptor适配器
hole gauge 孔深量测仪
high-temperature grease 高温油脂
thermal conductivity paste 导热膏
data cable数据线
compression mold base 压缩模胚
countersunk 埋头孔锥孔,沉孔
mill 压榨机;磨坊;碾磨;
drill钻头;钻床钻孔;钻通
grind 磨擦;磨碎;磨光
turn 转动;旋转;翻转
adapter plate 适配模板
leader pin; shoulder leader pin 导针;带肩导针( 实心) angle pin(horn pin) 斜针;斜边
straight bushing 直导套(空心)
shoulder bushing 带肩导套
sprue puller pin 唧咀扣针
sprue spreader 浇口分流锥
runner spreader 流道分流锥
tapered interlocks(round & rectangular) 啤把锁bronze plated bushing 镀铜导套
guided ejection bushing 导向导套
toggle-lock early ejector return 切换式早期回撞装置accelerated knock-out 加速顶棍
accelerated ejector 加速顶针
collapsible core 可折叠式的型芯
slide retainer 行位固定装置
jiffy latch-lock assemblies 快速拉杆锁定装置
tapped hole 螺丝孔
no resettable shot counter 非复位注射计数器
profiled ejector pin 底面在有倾斜截面的顶针
copper 红铜
brass 黄铜
bronze 青铜
BeCu 铍铜
counterbore 拔头,介子托
fan gate 扇形入口
fillet 圆形入口
pin point gate 细水口
hose clip 入喉箍
jiggle斜顶
British Standard Whitworth thread BSW 英制螺丝(粗牙)
British Standard Fine Thread BSF 英制螺丝(幼牙)
National Pipe Thread 美制螺牙
pressure plug 喉塞
pressure spring 压力弹簧
vent 疏气孔
alignment strip斜锁
ball catch 弹弓波子
bridge piece 水口铁
Jiffy-matic connector 快速连接喉
All ejector blades must have key to avoid rotating 扁顶要管定,以防旋转. ejector bearing length弹弓压缩长度
reinforcement rib 加强筋
steel pad 方铁
latch 拉杆
sprue puller insert 扣针导套
stage ejector=knock out 顶棍
ejector retainer plate 上顶针板
ejector base plate 下顶针板
stripper plate 活动板
runner stripper plate 脱料板
P/L flash 分形面披锋
scrape 拖花
burn 烧黑
safety strap 码板
side gate system 大水口系统
three plate type system 简化型细水口系统
pin point gate system 细水口系统
guide pin/guide bush 直边/托司
top clamp plate 工字板
stripper plate 推板
spacer block 方铁
bottom clamp plate 底板
shoulder guide pin 带肩导针
shoulder guide bush 托司
straight guide bush 直司/直导套
guide pin 直边
screw thread 螺纹
air pump 空气泵
alloy 合金
alloy steel 合金钢
定模座块 fixed clamp plate;top clamping plate;top plate
动模座块 moving clamp plate;bottom clamping plate;bottom plate 上模座块 upper clamping plate
下模座块 lower clamping plate
凹模固定板 cavity-retainer plate
型芯固定板 core-retainer plate
突模固定板 punch-retainer plate
模套 chase;bolster;frame
支承板 backing plate;support plate
垫块 spacer;parallel
支架 ejector housing,mould base leg
斜销 angle pin,finger cam
滑块 slide,cam slide
侧芯型滑块 side core slide
滑块导板 side guide strip
楔紧块,撑鸡 heel block,wedge bock
斜槽导板 finger guide plate
弯销 dog-leg cam
斜滑块 angle-lift splits
导向零件
导柱 guide pillar;guide pin;leader pin
推板导柱 ejector guide pillar;ejector guide pin 带头导套 guide bush;guide bushing
推板导套 ejector guide bush;ejector bushing
定位和限位零件
锥形定位件 mould bases locting elements
复位杆 ejector plate return pin,push-back pin 限位块 stop block; stop pad
定距拉杆 length bolt; puller bolt
定距拉板 puller plate; limit plate
推出零件
推流道板 runner stripper plate
分流道拉料杆 runner puller; runner lock pin
拉流杆;扣针 sprue puller
钩形拉料杆 sprue puller, Z-shaped
球头拉料杆 sprue puller,ball-headed
圆锥头拉料杆 sprue puller,conical headed
连接推杆 ejector tie rod
推板 ejector plate;ejection plate
推杆固定板 ejector retainer plate
推件环(盘) stripper ring(disk)
推件板 stripper plate
推块 ejector pad
推管(司筒,导筒) ejector sleeve
推杆 ejector pin
圆柱头推杆 ejector pin with cylindrical head
带肩推杆 shouldered ejector pin
扁推杆 flat ejector pin
塑料成型模具的主要设计要素
脱模距 stripper distance
脱模斜度 draft
投影面积 projected area
最大开距 maximum daylight;open daylight
闭合高度 mould-shut height
抽芯距 core-pulling distance
抽芯力 core-pulling force
脱模力 ejector force
开模力 mould opening force
模内压力 internal mould pressure;cavity pressure 成型压力 moulding pressure
背压环 back-up ring
1.bar =
高压接头 bite type fitting
液压马达 hydraulic motor
冷却水流量计 waterflow regulator
打磨器材 abrasive material
打磨砂轮 grinding wheels
切割砂轮 cutting wheels
码模夹(注塑机使用)mould clamps; lifting clamps
小五金工具 piping tools
高压力软管 high pressure hose
风管,水软管 air .water hose
高压油表 pressure gauge
压力油喉 hydraulic hoses
光塑检测 photoelastic testing
吹塑模 plastic blow mould
注塑模 plastic injection mould
冲扎复合模 blank & form compound die
精密冲模 precision blanking die
熔料流动率 MFR=melt flow rate
熔料流动指数 MET=melt flow index
推板导柱 guide pin for ejector plater
座板 clamping plate
垫块 space block(plate)
推板 ejector block(plate)
afdek plate 档尘板
guide stripe 行位后板
cavity sub-insert 前模镶件
core sub-insert 后模镶件
sprue puller insert 扣针镶件
stage ejector 顶棍
spacer rock(risers) 间隔板
变形 distortion
弯曲 warp
拖花 drag marks
火花纹 EDM marks
困气 venting
烧黑 burns
表面缩水 shrinkage
料位过薄/砸穿 thin wall stock
走水不平行 uneven fill pattern
夹水纹/流纹 witness line;mismatch;stress marks 走水纹 knit lines
走水不齐 short shots
orifice 料口
nozzle seat 热嘴垫圈
nozzle plate 射嘴板
cross pin 十字头销
sled 射台
seal ring 封密圈
spacer rail 介子座
heater groove 发热管槽
heater cement 发热管的结合剂
soak 浸泡
seat 垫圈
ream 铰大圆孔直径
grind 磨床
drill 钻床
mill 铣床
caliper 卡尺
G-caliper 分厘卡
Depth Gauge 深厚计
hardness tester 硬度计
angle gauge 角规
marble table 云台石
projector 投影仪
height gauge 高度仪
microscope 显微镜
plug gauge 塞规
leveller 水平器
R gauge R 规
Inter caliper 内分厘卡
surface 平面仪
item number 细目编码
catalog number 材料分类编码undercut lip 倒扣口
hot tip = hot drop = nozzle 热嘴blow-off strip 放气板
blow-off nozzle 吹风口
spiral hose 螺旋式的连接喉
rust solvent 除锈剂
shaft 曲轴
tensile strength 拉伸力
yield strength 屈服力
spark erosion 电火花蚀刻
etch(photo-etch) 电蚀
harden 淬硬
copper electrode 铜公
corrosion resistance 耐腐蚀anneal 退火
heat treatment 淬火
FEM(finite elemnet method) 有限元法preliminary tool design 初期模具设计图zone 热流道区域
reverse taper 倒啤把
clamp plate 码板
toggle clamp 快速夹
vacuum furnace 真空炉
cavity insert rounds 圆柱镶件
cavity insert b0locks 方柱镶件
tensile strength 抗张强度,抗拉强度Concept drawing 概念图
Assembly drawing 装配图
mismatch;witness line 夹纹
shut-off(n.) 枕位
venting valves 疏气阀
venting plug 疏气塞
valve casing 阀门罩
twist drill 旋钻
harden/nitride 碎硬
anneal 退火
temper 回火
stess crack 应力断裂
corrosion resistance 防腐,防锈
tensile strength 抗张强度,抗拉强度
split mould (分离)组合式的模具
inclined plate 斜面
inclined bolt 斜栓
jaw (工具,机械等)夹住东西的部分,钳口
step change of the P/L 分形面枕位的改变thin steel section 较薄的料位
clean-up 清理,清除,清扫
Mold Dating Insert 模具日志镶件
Hot Sprue Bushing 热浇口套
semi-automatic 半自动
quick disconnector 快速断开接头
full shot 足量注射
mismatch 夹痕;夹水纹
ejector mark 顶痕
screw boss 螺丝孔,螺丝基座
sink mark 缩坑
15% glass filled ABS 掺有15%玻璃的ABS spraying mold release 脱模剂
drag mark 拖痕
stress mark 应力痕
reinforcement rib 加强筋
slght stoning 轻度磨砂
soliid line 实线
dotted line 虚线
internal diameter 内径
external diameter 外径
nickel-plated 电镀的
handling hole;lifting hole 吊装孔parallel 平行块
piston 活塞
plunger 柱塞
carrier 导轨
rest 支架
item number 项目编号
catalog item 商品目录编码
dimensional datum 尺寸基准
heat treatment certification 淬硬证明文件back-up bushing 支撑导套
jacking screw 起重螺丝,千斤顶
tapped hole (带有螺旋角度的)螺丝孔
diagonal corner 成对角的角落
burn mark 烧痕
hot runner mainfold (热流道板)分流板texuring 蚀纹
clamping screw (注塑机)码模螺丝
imperial 英制的
metric 公制的
puller bushing 水口套
puller bar 水口铁
drool bushing 防漏胶套筒
safety switch 限位制
water line connected internally or hard tubing 不可用胶喉连接运水lifter: on square rod or locked from rotation 用方形柱或用管钉防止斜顶转动
gate insert 入水镶件
gate shut-offs 流道开关配件
guided ejection 中托司
parting line shutoff 前后模接触面
waterlines clear tie bars. 运水喉咀接驳位要避开啤机呵林柱.
BGV=Balanced Gate Value 平衡入水值
spacer 垫块
pocket 挖槽
rough 粗加工
finish 精加工
plunge rate 进刀率
retract rate 提刀速率
splindle rate 主轴转速
coolant 冷却液
SPLIT RING 开口环(钥匙圈)
侧向抽芯力 side pulling-core force
转图
guide pin 边针
Tee slot cutter T形SLOT CUTTER
zigzag 双向切削
constant overlap spiral 等距环切
parallel spiral 环绕切削
parallel spiral clean corners 环切并清角
morph spiral 依外形环绕
true spiral 螺旋切削
one way 单向
end mill 平铣刀
spher mill 球刀
bull mill 圆鼻刀
face mill 面铣刀
rad mill 圆角成型刀
chamfer mill 倒角刀
slot mill 槽刀
taper mill 推拔铣刀
dove mill 鸠尾铣刀
lot mill 棒状
drill 钻孔
reamer 纹刀
bore bar 搪刀
tap RH 右牙刀
Tap LH 左牙刀
ctr Drill 中心钻
spot drill 点钻
cntr bore 沉头孔刀
c. sink 鱼眼孔钻
loft surface 举升曲面
coons surface 昆氏曲面
ruled surface 直纹曲面
revolved surface 旋转曲面
swept surface 扫描曲面
draft surface 牵引曲面
grinding wheel 磨砂使用的轮子
quench steel 将...淬火,使冷却
stress relieving 应力消除
molten 熔热的
oxide film 氧化层
guide pin and sleeve, locating ring ,ejector ,ejector balde, ejector sleeve,lifters, wear plate,horn pin,O ring, water baffle, water pipe plug,water line connector,wear plate ,air cylinder,hydraulic cylinder, micro switch,oil nipple, spring,sprue bushing,early return system, accelerated ejectors, slied holder,cycle counter,date stamper, hot runner syste 导边,司筒,定位圈,顶针,扁顶针,顶针司筒,斜坊,磨损板,气顶针,O形圈,隔片,运水管道塞,运水管道转接头,氯压缸,液压缸,开关装置,油枪接头,
弹弓,浇口套,早期回撞装置,加速顶针,注塑周期计数器,滑块固定板,生产日期铭牌,热流道系统
chemical composition 化学成份
thermal conductiivity 导热性能
thermal diffusivity 热扩散性能
dimensonal stablity 尺寸稳定性能
cooling effiency 冷却效率
easiler ejection 易于脱模
alloy insert 合金镶件
(cooling) duct 输送管;导管
maintenance cost 维护费用
ultrasonic testing 超声波检测
crack 断裂
direct gate 直接浇口
ring gate 环形浇口
disk gate;disphragm gate 盘形浇口
spoke gate;spider gate 轮辐浇口
pin-point gate 点浇口
edge gate 侧浇口
submarine gate;tunnel gate 潜伏浇口
fan gate 扇形浇口
tab gate 护耳浇口
runner plate 流道板(或冷或热)
secondary nozzle 二级喷嘴
torpedo;torpedo body assembly 鱼雷形组合体
catridge heater 管式加热器
heat pipe 热管
valve gate 阀式浇口
force plunger;pot plunger 柱塞
flash groove;spew groove 溢料槽
impression;cavity block;cavity plate 凹模
punch;force 凸模
movable insert;loose detail 活动镶件
cavity splits;core splits(凹模拼块) (型芯拼块) 拼块
side core 侧型芯
thread plug;threaded core 螺纹型芯
thread ring;threaded cavity 螺纹型环
cutting wheel 切割砂轮
grinding wheel 打磨砂轮
abrasive material 打磨器材
mould clamps;lifting clamp 砂模夹(注塑机使用) air (water) hose 风管,水轮管
pressure gauge 高压油表
hydraulic hose 压力油喉
plastic blow mould 吹塑模
plastic injection mould 注塑模
blandk&form compound die 冲扎复合模
precisiion blanking die 精密冲模
MFR=melt flow rate 熔料流动率
MFT=melt flow index 熔料流动指数
handling hole 拉铃孔
stop plate 限位块
linder bush 衬套
spacer block(plate) 垫块,方铁
back-up ring 背位环
standoff 限位块
American Safety Hoist Rings. 英制安全吊装环Mechanical Properties 机械性能
Tensile Strength(MPa) 抗拉强度
elongation 延伸率
hardness(Brinell) 硬度
shear stength(MPa) 剪切力
impact strength 冲ren性
Physical Properties 物理性能
solidification shrinkage 凝固收缩率
freezing range 凝固与熔范围
thermal expansion 热膨胀系数
specific heat 比热
thermal conductivity 热导率
electrical conductivity 电导率
micro-structure 金相分析
hot work tool steel 热作钢
circular motion 环形运动
variable 变量,参数
graphics window 图形窗口
45 degree entry and a zero degree exit. 进刀口45度,退刀口0度runner stripper plate 脱料板
stripper plate 活动板
spacer rock(risers) 间隔板
stage ejector 顶棍
sprue puller insert 扣针导套
guide strip 行位后板
afdek plate 挡尘板
side gate 大水口
pinpoint gate 细水口
SHCS 杯头螺丝
FHCS 平头螺丝
set screw 无头螺丝
ball catch 波子螺丝
wedge 行位较杯
gib 线条,(撑鸡的导轨)
latch 拉杆
clamp 码仔
spring guide pin 弹弓导柱
steel pad disc 橙仔方
ejector cam insert 斜顶块
(screw) nut 螺母
taper 嗲把/ 斜度
taper interlock 嗲把锁
texture 花纹
toggle-lok 回撞装置
top clamping plate 顶码板
unified national coarse (UNC) 美制螺丝(粗牙)
unified national fine (UNF) 美制螺丝(幼牙)
set screw 喷头螺丝
side gate 大水口
slide retainer 行位管位
water junction 喉咀
spacer block 登仔
jiffy-matic socket 喉咀套
jiffy-tite plug 喉咀公
spring plunger 弹弓座
sprue puller 勾针/勾粒
spring washer 弹簧塑圈
stepped ejector pin 有托顶针
strippers plate 推板/细水口板
submarine gate 潜水口
support pin 拉杆
support plate 暗板
surface finish 光洁度
alignment strip 斜锁
angle pin 斜针
fan gate 扇形入水
fillet 圆口
ball catch 弹弓波子
blade ejector 扁顶
bottom clamping plate 底码板
free length 自然长度
bridge piece 水口铁
British Standard Fine Thread (BSF) 英制螺丝(幼牙) British Standard Pipe Thread (BSP) 英制喉牙
British Standard Whitworth Thread (BSW) 英制螺丝(粗牙) helix spindle 锅杆
hose clip 水喉箍
bubbler 隔气运水
jiggle 斜顶
jiggle witness line 斜顶片位置
center distance (CRS) 山打距离(中心线距离)
clamp 码仔
contour 外形
leader pin 导针
location ring(flange) 法兰
counterbore 拔头,介子托
mock-up;prototype 手办
die cast 合金压铸
national pipe thread(NPT) 美制喉牙
overflow 垃圾位
ejection sleeve 司筒,顶套
epoxy 胶样
pin point gate 细水口
pressure plug 喉塞
pressure spring 压力弹簧
parting line flash 披锋
burned 烧黑
underfilled 缺料
insert mismatch 镶件夹口
ejector pins not flush 顶针有高低
ejector pins skid 顶针滑动
insert flash 镶件披锋
pressure transducer 压力探测头
hydraulic schematic 油积筒油路接驳图
jiffy connector recessed 安装喉嘴后不可突出模胚
knock out pullback stud -flush with clamp plate 顶棍镶件与底板有否空间safety switches 限位制
stop block 限位块
safety strap 安全带
drool bushing 防漏胶套筒
insert mismatch 镶件夹口
EDM visible 明显火花纹
lifter scrapes 斜顶拖花
short shots 走水不齐
wall stock 料位厚薄
knit lines 走水纹
stress marks 夹水纹
uneven fill pattern 走水不平行
drag marks 拖花
sprue pretrusion 唧嘴突出高度
sprue orifice and radil size 唧嘴R尺寸
sprue bushing-keyed 唧嘴有管钉
English Chinese
program name 产口名称
part name 零件名称
tool name 模具名称
tool source 模具来源
tool steel 模具钢材
resin 塑料
program number 产品编号
part number 零件编号
tool number 模具编号
customer 客户名称
No of cavities 内模编号
machine size 啤机吨数
drum miller 鼓形铣床
duplex horizontal miller 复式卧铣床face miller 端面铣床
grinding miller 研磨机
plain miller 平面铣床
planer-type miller 刨式铣床
rack miller 齿条铣床
slab miller 大型平面铣床
slot miller 键槽铣刀
spline miller 花键铣刀
thread miller 螺纹铣刀
vertical miller 立式铣刀,立辊,立辊轧机endmill 立铣刀
plastic mould steel 塑料模钢
cold work steel 冷作钢
hot work steel 热作钢
high speed steel 高速钢
electric magnetic clutch 电磁离合器pad printer 移印机
screen printer 丝印机
hot stamper 烫印机
solid carbide slitting saw 钻石钢锯片
convex cutter 凸锣刀片
concave cutter 凹锣刀片
side&face cutters,staggered teeth 正侧双用镶钻石钢锣刀end-mill 锣刀
semi-rod 半圆刀
split double end 双头刀
single end 单头刀
2-flute 两辨
3-flute 三辨
4-flute 四辨
reamer 直拈
centre drill 中心钻
solid carbide drill 钻咀
zinc ingot 锌锭
aluminium ignot 铝锭
tin ignot 锡锭
heater cement 发热管的结合剂
heater groove 发热管槽
spacer rail 介子座
cross pin 十字头销
nozzle plate 射嘴板
nozzle seat 热嘴
addendum 齿冠
dedendum 齿根
air compressor 空气压缩机
air exhauster 抽气机
air intake 进气口
Assembly line组装线
Layout布置图
Conveyer流水线物料板
Rivet table拉钉机
Rivet gun拉钉枪
模具方面的中英文对照
模具方面的中英文对照【二】 2007-05-09 22:35 塑料成型模具的主要设计要素 脱模距 stripper distance 脱模斜度 draft 投影面积 projected area 最大开距 maximum daylight; open daylight 闭合高度 mould-shut height 抽芯距 core-pulling distance 抽芯力 core-pulling force 脱模力 ejector force 开模力 mould opening force 模内压力 internal mould pressure; cavity pressure 成型压力 moulding pressure 背压环 back-up ring 1 bar = 14.5psi 高压接头 bite type fitting 液压马达 hydraulic motor 冷却水流量计 waterflow regulator 打磨器材 abrasive material 打磨砂轮 grinding wheels 切割砂轮 cutting wheels 码模夹(注塑机使用) mould clamps; lifting clamps 小五金工具 piping tools 高压力软管 high pressure hose 风管,水软管 air .water hose 高压油表 pressure gauge 压力油喉 hydraulic hoses 光塑检测 photoelastic testing 吹塑模 plastic blow mould 注塑模 plastic injection mould 冲扎复合模 blank & form compound die 精密冲模 precision blanking die 熔料流动率 MFR=melt flow rate 熔料流动指数 MET=melt flow index 推板导柱 guide pin for ejector plater 座板 clamping plate 垫块 space block(plate) 推板 ejector block(plate) afdek plate 档尘板 guide stripe 行位后板 cavity sub-insert 前模镶件 core sub-insert 后模镶件 sprue puller insert 扣针镶件
常用模具零件中英文对照表
常用模具零件中英文对照表 2005-12-19 14:51:17中国注塑网 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin
模具DFM常用中英文对照
DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick
模具中英文对照表
landed plunger mold 有肩柱塞式模具burnishing die 挤光模 landed positive mold 有肩全压式模具button die 镶入式圆形凹模 loading shoe mold 料套式模具 center-gated mold 中心浇口式模具loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模 louvering die 百叶窗冲切模composite dies 复合模具 manifold die 分歧管模具 counter punch 反凸模 modular mold 组合式模具 double stack mold 双层模具 multi-cavity mold 多模穴模具electroformed mold 电铸成形模 multi-gate mold 复式浇口模具expander die 扩径模 offswt bending die 双折冷弯模具extrusion die 挤出模
palletizing die 叠层模 family mold 反套制品模具 plaster mold 石膏模 blank through dies 漏件式落料模porous mold 通气性模具duplicated cavity plate 复板模positive mold 全压式模具 fantail die 扇尾形模具 pressure die 压紧模 fishtail die 鱼尾形模具 profile die 轮廓模 flash mold 溢料式模具progressive die 顺序模 gypsum mold 石膏铸模 protable mold 手提式模具 hot-runner mold 热流道模具prototype mold 雏形试验模具ingot mold 钢锭模 punching die 落料模 lancing die 切口模 raising(embossing) 压花起伏成形re-entrant mold 倒角式模具
模具常用术语中英文对照表
"R，L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具方面的中英文对照
查看文章模具方面的中英文对照【二】2007-05-09 22:35 塑料成型模具的主要设计要素脱模距stripper distance 脱模斜度draft 投影面积projected area 最大开距maximum daylight;open daylight 闭合高度mould-shut height 抽芯距core-pulling distance 抽芯力core-pulling force 脱模力ejector force 开模力mould opening force 模内压力internal mould pressure;cavity pressure 成型压力moulding pressure 背压环back-up ring 1 bar = 14.5psi 高压接头bite type fitting 液压马达hydraulic motor 冷却水流量计waterflow regulator 打磨器材abrasive material 打磨砂轮grinding wheels 切割砂轮cutting wheels 码模夹（注塑机使用） mould clamps; lifting clamps 小五金工具piping tools 高压力软管high pressure hose 风管,水软管air .water hose 高压油表pressure gauge 压力油喉hydraulic hoses 光塑检测photoelastic testing 吹塑模plastic blow mould 注塑模plastic injection mould 冲扎复合模blank & form compound die 精密冲模precision blanking die 熔料流动率MFR=melt flow rate 熔料流动指数MET=melt flow index 推板导柱guide pin for ejector plater 座板clamping plate 垫块space block(plate) 推板ejector block(plate) afdek plate 档尘板guide stripe 行位后板cavity sub-insert 前模镶件core sub-insert 后模镶件sprue puller insert 扣针镶件 stage ejector 顶棍
模具中英文对照
中英名詞對照 一.劃 一般商業用模座：Commercial die set 二.劃 V字形靠柵：V-gaging 三.劃 1.工作單：Operation sheet 2.三角形沖片：Triangular blank 3.小沖床沖模：Sub-press die 4.工作流程單：Route sheet 5.下驅動沖床：Underdrive press 6.三角形打料板：Knockout plate spider 7.工具校驗部門：Tool inspection depart 四.劃 1.分圓：Detail drawing 2.止動銷：Dutchman 3.雙行排列：Layout double-raw 4.分裝模體：Split die block 5.方頭駐螺：Square-head set screw 6.中心莰入件：Center insert 7.水硬工具鋼：Water hardening tool Steel 1.尺寸與注記：Dimensions and notes 2.六方埋頭螺絲：Socket cap screw 3.孔徑尺寸注記：Dimension of hole 4.手動定位裝置：Finger stop 5.雙排沖切設計（排列）：Double-raw layout 五道次沖切排列：Rive-station layout 五.劃 1.切圓：Cutting ring 2.切邊：Trimming 3.打料桿：Knockout rod 4.避位：Stiffening 5.半銅模座：Semi-steel die set 6.另件布置：Part layout 7.引伸沖模：Dies drawing 8.皮料加工：Finish of sheet 9.打料柱塞：Knockout plunger 10.打料裝置：Knockouts 11.可卸道筒：Demountable guide bushing 1.切斷沖模：Gutoff die 2.切邊裕度：Allowance or trimming 3.切邊沖模：Trimming die 4.平頭埋頭螺：Flat head screw socket 1.四道柱沖床：Four-post press 2.四道柱模座（沖模模座）：Four-post die sct 1.引伸零件展開：Development of drawn parts 1.半陰式定位銷：Semi-blind dowel 2.平行四邊形沖片：Parallelogram shaped blank 六.劃 1.沖扁（沖鍛）：Stamping 2.沖頭把：Punch shank 3.先道桿：Pilot 4.沖片毛邊：Burrside of blank 5.沖片加工：Blanking 6.沖片沖頭：Blanking 7.沖切長口：Slitting 8.沖孔沖床：Punch press 9.沖孔沖頭：Piercing punch 10.沖孔沖模：Die piercing 11.沖片沖模：Blanking die 12.沖片設計（安排）：Blank layout 13.沖片面積：Area of blank 14.沖床附件：Press accessories 15.沖床動力：Power for press 16.沖床構造：Press construction 17.自動沖床：Automated press 18.先道桿簧：Spring pilot 19.曲軸總成：Crankshaft assembly 20.沖模套筒：Die bushing 21.沖模間隙：Die Clearance 22.沖模截塊：Die section 23.沖模模座：Die set 24.沖彎公式：Bend formula
模具--中英文对照
dowel pin 定位梢 draft 拔模锥度 draw bead 张力调整杆 drive bearing 传动轴承 ejection pad 顶出衬垫 ejector 脱模器 ejector guide pin 顶出导梢 ejector leader busher 顶出导梢衬套ejector pad 顶出垫 ejector pin 顶出梢 ejector plate 顶出板 ejector rod 顶出杆 ejector sleeve 顶出衬套 ejector valve 顶出阀 eye bolt 环首螺栓 filling core 椿入蕊 film gate 薄膜形浇口 finger pin 指形梢 finish machined plate 角形模板 finish machined round plate 圆形模板fixed bolster plate 固定侧模板flanged pin 带凸缘销 flash gate 毛边形浇口 flask 上箱 floating punch 浮动冲头 gate 浇口 gate land 浇口面 gib 凹形拉紧楔 goose neck 鹅颈管
guide bushing 引导衬套 guide pin 导梢 guide post 引导柱 guide plate 导板 guide rail 导轨 head punch 顶头冲孔 headless punch 直柄冲头 heavily tapered solid 整体模蕊盒hose nippler 管接头 impact damper 缓冲器 injection ram 压射柱塞 inlay busher 嵌入衬套 inner plunger 内柱塞 inner punch 内冲头 insert 嵌件 insert pin 嵌件梢 king pin 转向梢 king pin bush 主梢 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner, hot manifold 热嘴冷流道: hot sprue/cold runner
模具DFM常用中英文对照
DFM常用中英文对照 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， Stick 1.High shrinkage values could indicate sink marks or voids at gate location 高缩水率的产品容易产生缩印，但 在浇口附近可以避免。 2.Welding line on the cosmetic surface 熔接线在外表面 3.Two banana gate was to being confluent in the end of melt flow. 两个香蕉浇口在流动未端熔合。 4.Venting insert here has flash 排气镶件处有飞边 5.Venting gap between inserts is too big 镶件处的排气槽过大 6.Stress mark on the cosmetic surface 产品外表面上有压痕 7.Uneven thickness 不平均的产品壁厚 8.Unreasonable product structure 不合理的产品结构 9.Injection speed is high 注塑压力过高 10.There is black spot on the cosmetic surface 产品外表面上有黑色点 11.There is flash on the product 产品有飞边 12.there is sink mark on the cosmetic surface 产品外表面上有缩痕 13.Gate size is not reasonably 浇口尺寸不合理 14.There is argent spot 这里有亮点（银色斑点） 15.The plastic of first shot didn't meet high temperature. 塑料的第一胶不会有很高的温度。 16.Make sure the core float plate was closed before lifter completely return to correct position 确认 lifter完全回位时core侧浮动板已经复位 17.Make sure the ejector system is smooth 确认顶针系统移动平稳 18.Add early return structure to protect lifter return to correct position 增加先复位机构保护lifter回到正确 位置。 19.Propose to add draft on slider side wall and draw polish. 建议增加 slider的角度和抛光角度。 20.It is too thin and very difficult to inject fully, and weakness wall will have risk of the part function 该 处壁厚过薄而造成很难去填充完整，薄壁将会有产品功能上的风险。 21.These are will have sink marks due to uneven thickness, propose to reduce plastic. 壁厚不均匀容易产生缩印， 建议在该处减胶。 22.These are will have sink marks due to ribs opposite. 正面的筋位易导致背面产生缩印。 23.Please confirm the 3D part thickness whether has including painting thickness or not? 请确认产品的设计是否
五金模具常用专业术语中英文对照表[1]
五金模具常用专业术语中英文对照表 上模座upper die set成型公form punch 脱料板stripper 垫板subplate/backup plate 下模座die plate滑块CAM slider 垫脚parallel 误检misfeeder 托板mounting plate顶料销kick off 初始管位first start pin带肩螺丝shoulder screw 两用销lifter pin氮气汽缸gas spring 弹簧护套spring cage 拔牙螺丝jack screw 侧冲组件cam section 导正装置guide equipment 漏废料孔slug hole刀口trim line 加强装置enhance equipment 入子insert 护套bushing 整形公restrike forming punch 止挡板stop plate 挂台head 扣位pocket of head 导柱guide post 导套guide bushing 油嘴oil nipple 接刀口mismatch/cookie bites 限位块stop block 挡块stopper 浮块lifter 压块keeper 靠块heel 对正块alignment block 简易模prototype tooling 检具gage/checking fixture 料带图strip layout 闭合高度shut hight 俯视图top view 料带strip 公差tolerance 正视图front view 走位travel 避位/空pocket 退磁demagnetization 间隙clearance 真空热外理vacuum heat treatment 镗孔mill hole 表面外理surface coasting 镀钛TD coasting 沉头counter sink 精锣finish mill 线割wire cutting 穿丝孔first wire hole 斜度taper 镭射laser-cut 上夹板/固定座holder/retainer 下模座lower die set 成刑母公forming die 电火花EDM 码模槽mounting slot 球锁紧固定座ball-lock 导尺rail 球锁紧凸模BALL--LOCK 送料板rail plate 外购out sourcing 倒角chamfer 清角SCRAP CHOPPER 销钉dowel 尖角sharp --angle 普通弹簧coil spring 展开图EXPENSINg DWG 三打螺丝spool 镶件insert 毛刺burr 键销key 插针pilot pin
模具常用中英文对照
模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level
材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner V ents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug
模具用语中英文对照
模具用语中英文对照 198各式模具分类用语中英文对照 landed plunger mold 有肩柱塞式模具 burnishing die 挤光模Www_17He_com landed positive mold 有肩全压式模具 button die 镶入式圆形凹模一起呵_英语站loading shoe mold 料套式模具center-gated mold 中心浇口式模具一起呵@英语站loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模一起呵@英语站louvering die 百叶窗冲切模 composite dies 复合模具英.语.站 manifold die 分歧管模具一起呵_英语站counter punch 反凸模英语.站 modular mold 组合式模具 double stack mold 双层模具17He~Com multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模一起呵.英语.站offswt bending die 双折冷弯模具
extrusion die 挤出模英语.站 palletizing die 叠层模一起呵@英语@站family mold 反套制品模具一.起.呵.英语站plaster mold 石膏模 17he_com blank through dies 漏件式落料模一porous mold 通气性模具duplicated cavity plate 复板模一起呵@英语站positive mold 全压式模具 fantail die 扇尾形模具 17he_com pressure die 压ingot mold 钢锭模 punching die 落料模 lancing die 切口模英语.站 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具一起呵_英语站 sectional die 对合模具 英.语.站 segment mold 组合模一起_呵_英语站 semi-positive mold 半全压式模具一起_呵_英语站 shaper 定型模套 single cavity mold 单腔模具
模具常用术语中英文对照
模具常用术语中英文对照 模具常用术语中英文对照 中文英文 模芯Parting Core 局部视图Partial View 冷料# ColdSllig 线切割Wire E.D.M 轮廊Contour 螺纹孔Tapping Hole 连接件Fittings 斜针AnglePin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机SpecificPress 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-LeaderdPin 镶件Mold Insert 加硬Hapden 唧嘴Sprue 设计筒图DesignPreliminary 名称块表 Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试LeakTest 流道排气Runner Vents 抛光Draw Polish 侧抽芯SideAction 中文英文加强筋Reinforcing 三角撑Gusset 柱子Bosse 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔Handl Ing Hole 运输安全带Moldstrap 码
模槽ClampSlot
撑头Support Pillar 螺牙1/2-13 EyeBolt 1/2-13Tap 导柱位LeaderPin Location 耐落胶Teflon Paste 偏移量Offset 水塞 Water Line Plig 撬模脚PpySlot 重新加工Reworked 配件Components 补偿 Compensation 平面度 Parallel 倒角 Chamfer 模胚 Mold Base 热嘴 Hotnozzle 火花机 Edm 熔接线 Weildline 压机 Press 晒纹 Texturing 梯形Trapezoio 凸缘、法兰Flange 模具常用术语中英文对照 中文英文 方铁 SpacerBlock 顶针板 Ejector Plate
模具零件名称中英文对照一览表
模具零件名称中英文对照一览表 零件名称ENGLISH NAME 零件名称ENGLISH NAME 上固定板TOP CLAMPING PLATE 母模仁CAVITY 母模板CAVITY PLATE 公模仁CORE 公模板CORE PLATE 母模入子CAVITY INSERT 模脚SUPPRORT BLOCK 母模心子CAVITY INSERT PIN 上顶出板EJECTOR RET PLATE 母模替换入子CAVITY CHANGEABLE INSERT 下顶出板EJECTOR PLATE 公模入子CORE INSERT 下固定板BOTTOM CLAMPING PLATE 公模心子CORE INSERT PIN 隔热板THERMAL INSULATING PLATE 公模替换入子CORE CHANGEABLE INSERT 脱料板RUNNER STRIPPER PLATE 滑块入子SLIDE INSERT 母模垫板CAVITY SUPPORT PLATE 滑块心子SLIDE INSERT PIN 公模垫板CORE SUPPORT PLATE 斜销入子ANLGE LIFTER INSERT 脱料板STRIPPER PLATE 斜销心子ANLGE LIFTER PIN 流道板RUNNER PLATE 流道开关RUNNER SHUT OFF 定位环LOCATING RING T 形块T GIB 注口衬套SPRUE BUSHNG U 形块U GIB 导柱LEADER PIN 拉料销SPRUE PULLER PIN 导套LEADER BUSHING 定位销DOWEL PIN 顶板导柱GUIDE PIN 顶针EJECTOR PIN 顶板导套GUIGE BUSHING 扁销RECTANGLE EJECTOR PIN 大拉杆LARGE PULLER PIN 套筒EJECTOR SLEEVE 小拉杆SMALL PULLER PIN 顶出块EJECTOR BLOCK 支撑柱SUPPORT PILLAR 斜销ANGLE LIFTER 定位块INTERLOCKS 斜销座ANGLE LIFTER BASE 定位柱LOCATION PILLAR 引导块GUIDE BLOCK 开闭器(塑料型) FRICTIONAL PULLER 急回推杆LEVER 弹簧SPRING 冷却棒THERMAL PIN 运输板PL LOCK O 形环O RING
模具专业英文术语大全
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水：gate 进入位：gate location 水口形式：gate type 大水口：edge gate 细水口：pin-point gate 水口大小：gate size 转水口：switching runner/gate 唧嘴口径：sprue diameter 二、流道: runner 热流道：hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴：hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头：connector plug 插座：connector socket 密封/封料：seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件：mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板：support plate 螺丝：screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针：ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）：mold base 上内模：cavity insert 下内模：core insert 行位（滑块）：slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴：sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug 锁模块：lock plate 斜顶：angle from pin
模具英文缩写对照
模芯 Parting Core 局部视图 Partial View 冷料# Cold Slag 线切割 Wire E.D.M 轮廊 Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针 Angle Pin 接合 Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机 Specific Press 水嘴接头 Water Fittings 螺纹 Eyebolt Thread 回针 Stop Pin 二级顶出针 Sub-Leaderd Pin 镶件 Mold Insert 加硬 Harden 唧嘴 Sprue 设计筒图 Design Preliminary 名称块表 Title Block 版本标识 Revision Level 材料清单 Stock List 制模 Build Mold 手动滑块 Hand Slide 漏水测试 Leak Test 流道排气 Runner Vents 抛光 Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing 三角撑 Gusset 柱子 Bossed 出模斜度 Draft 外廊 Contour 落单会议 Kick-Off Meeting 装卸孔 Handling Hole 运输安全带 Moldstrap 码模槽 Clamp Slot 撑头 Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞 Water Line Plug 撬模脚 Ppy Slot