直导套 Straight Guide bush
动模座板Bottom clamp plate
Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate
凸模固定板punch-retainer plate
顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould
多浇口multi-gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force
锁模力mould locking force
挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate
轮辐浇口spoke gate , spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate 料穴cold-slug well
浇口套sprue bush
流道板runner plate
排飞槽vent
分型线(面)parting line
定模stationary mould,Fixed mould 动模movable mould, movable half
上模upper mould, upper half
下模lower mould, lower half
型腔cavity
凹模cavity plate,cavity block
拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock
拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line (flow line)
三板式模具three plate mould
脱模ejection
换模腔模具 interchangeable cavity mould
脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould,cavity block
阳模male mould
电加工设备Electron Discharge Machining
数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller 立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine 四、品管
SPC statistic process control
品管保证Quality Assurance
品管控制Quality control
来料检验IQC Incoming quality control
巡检IPQC In-process quality control
校对calibration
动态试验dynamic test
环境试验Environmental test
非破坏性试验non-destructive test
光泽gloss
击穿电压(dielectric) breakdown voltage
拉伸强度tensile strength
冷热骤变试验thermal shock test
环境试验炉Environmental chamber
盐雾实验salt spray test
绝缘电阻测试验仪Insulating resistance meter 内应力internal stress
疲劳fatigue
蠕变creep
试样specimen
撕裂强度tear strength
缩痕shrink mark, sink mark
耐久性durability
抽样sampling
样品数量sample size
AQL Acceptable Quality level
批量lot size
抽样计划sampling plan
OC曲线operation curve
试验顺序sequence of tests
环境温度ambient temperature
可焊性solderability
阻燃性flame resistance
五、生产
注塑机injection machine
冲床Punch machine
混料机blender mixer
尼龙nylon
黄铜 brass
青铜 bronze
紫(纯)铜 copper
料斗hopper
麻点pit
配料compounding
涂层coating
飞边flash
预热preheating
再生料reworked material
再生塑料reworked plastics
工艺设计process design
紧急停止emergency stop
延时time delay
六.物控
保质期shelf life
ABC分类法ABC Classification
反常需求Abnormal Demand
措施信息Action Message
活动报告标志Action-report-flag
基于活动的成本核算Activity-based Costing (ABC) 实际能力Actual Capacity
实际成本Actual Costs
调整现有库存量Adjust-on-hand
已分配量Allocation
替代工序Alternative Routine
装配订单Assembly Order
装配零件表Assembly Parts List
装配Assembly
计划自动重排Automatic Rescheduling
可达到库存Available Inventory
可用材料Available Material
达到库存Available Stock
可利用工时Available Work
可签约量Available-to-promise
平均库存Average Inventory
欠交订单Back Order
倒序计划Back Scheduling
倒冲法Back flush
未完成订单Backlog
现有库存余额Balance-on-hand Inventory
批号Batch Number
批量生产Batch Production
标杆瞄准Benchmarking
工时清单Bill of Labor
提货单Bill of Lading
物料清单Bill of Material
分库Branch Warehouse
经营规划Business Plan
采购员Buyer
能力管理Capacity Management
能力需求计划Capacity Requirements Planning (CRP)
保管费率Carrying Cost Rate
保管费Carrying Cost
单元式制造Cellular Manufacturing
修改批量日期Change Lot Date
修改工序Change Route
修改产品结构Change Structure
检查点Check Point
闭环物料需求计划Closed Loop MRP
通用工序标识Common Route ID
计算机集成制造Computer-integrated Manufacturing (CIM)
配置代码Configuration Code
约束管理/约束理论Constraints Management/Theory of Constraints (TOC) 依成本的材料清单Costed Bill of Material
急需零件Critical Part
累计提前期Cumulative Lead Time
现有运转时间Current Run Hour
现有运转数量Current Run Quantity
周期盘点Cycle Counting
调整日期Date Adjust
有效日期Date Available
修改日期Date Changed
结束日期Date Closed
截止日期Date Due
生产日期Date in Produced
库存调整日期Date Inventory Adjust
作废日期D ate Obsolete
收到日期Date Received
交付日期Date Released
需求日期Date Required
发货日期Date to Pull
空负荷Dead Load
需求管理Demand Management
需求Demand
实际能力Demonstrated Capacity
非独立需求Dependent Demand
直接增减库存处理法Direct-deduct Inventory Transaction Processing
发料单Disbursement List
派工单Dispatch List
分销资源计划Distribution Resource Planning (DRP)
鼓-缓冲-绳子Drum-buffer-rope
经济订货批量Economic Order Quantity (EOQ)
工程变更生效日期Engineering Change Effect Date
工程变更生效单Engineering Change Effect Work Order
工程停止日期Engineering Stop Date
例外控制Exception Control
呆滞材料分析Excess Material Analysis
急送代码Expedite Code
加工订单Fabrication Order
补足欠交Fill Backorder
总装提前期Final Assembly Lead Time
确认的计划订单Firm Planned Order
固定订货批量F ixed Order Quantity
集中预测Focus Forecasting
完全跟踪Full Pegging
通用生产管理原则Generally Accepted Manufacturing Practices 毛需求Gross Requirements
在制品库存In Process Inventory
独立需求Independent Demand
投入/产出控制Input/ Output Control
检验标识Inspection ID
厂际需求Interplant Demand
库存周转率Inventory Carry Rate
仓库库位类型Inventory Location Type
库存周转次数Inventory Turnover
发送订单Issue Order
项目记录Item Record
物料项目Item
加工车间Job Shop
准时制生产Just-in-time (JIT)
看板Kanban
人工工时Labor Hour
最后运输日期Last Shipment Date
提前期Lead Time
层Level
负荷量Load Leveling
负荷报告Load Report
负荷Load
仓位代码Location Code
仓位备注Location Remarks
仓位状况Location Status
按需订货Lot for Lot
批量标识Lot ID
批量编号Lot Number
批量Lot Size
低位码Low Level Code
机器能力Machine Capacity
机器加载Machine Loading
外购或自制决策Make or Buy Decision
面向订单生产的产品Make-to-order Product
面向库存生产的产品Make-to-stock Product
制造周期时间Manufacturing Cycle Time
制造资源计划Manufacturing Resource Planning (MRP II)
主生产计划Master Production Schedule (MPS)
物料成本Material Cost
物料发送和接收Material Issues and Receipts
物料需求计划Material Requirements Planning (MRP)
登陆标志MPS Book Flag MPS
多重仓位Multiple Location
净改变式MRP N et Change MRP
净需求Net Requirements
新仓位New Location
新组件New Parent
新仓库New Warehouse
不活动报告No Action Report
现有库存量On-hand Balance
未结订单Open Order
订单输入Order Entry
订货点Order Point
订货方针Order Policy
订货承诺Order Promising
订货备注Order Remarks
双亲Parent
零件清单Part Bills
零件批次Part Lot
零件编号Part Number
零件Part
反查Pegging
领料单Picking List
领料/提货Picking
计划订单Planned Order
后减库存处理法Post-deduct Inventory Transaction Processing 前减库存处理法Pre-deduct Inventory Transaction Processing 发票价格Price Invoice
采购订单价格Price Purchase Order
优先计划Priority Planning
产品控制Product Control
产品线Production Line
生产规划编制Production Planning
产品率Production Rate
产品结构树Production Tree
预计可用库存Projected Available Balance
采购订单跟踪Purchase Order Tracking
已分配量Quantity Allocation
仓位数量Quantity At Location
欠交数量Quantity Backorder
完成数量Quantity Completion
需求量Quantity Demand
毛需求量Quantity Gross
进货数量Quantity In
排队时间Queue Time
队列Queue
重生成式MRP Regenerated MRP
重排假设Rescheduling Assumption
资源需求计划Resource Requirements Planning 粗能力计划Rough-cut Capacity Planning
工艺路线Routing
安全库存量Safety Stock
保险期Safety Time
预计入库量Scheduled Receipt
残料率Scrap Factor
发送零件Send Part
维修件Service Parts
发货地址Ship Address
发货单联系人Ship Contact
发货零件Ship Date
发货单Ship Order
工厂日历Shop Calendar
车间作业管理Shop Floor Control
损耗系数Shrinkage Factor
标准产品成本Standard Product Cost
标准机器设置工时Standard Set Up Hour
标准单位运转工时Standard Unit Run Hour
标准工资率Standard Wage Rate
状况代码Status Code
库存控制Stores Control
建议工作单Suggested Work Order
约束理论Theory of Constraints (TOC)
时间段Time Bucket
时界Time Fence
单位成本Unit Cost
采购计划员Vendor Scheduler
采购计划法Vendor Scheduling
工作中心能力Work Center Capacity
工作中心Work Center
在制品Work in Process
工作令跟踪Work Order Tracking
工作令Work Order
工作进度安排Work Scheduling
零库存Zero Inventories
经济订货批量=Squat(2*年订货量*平均一次订货准备所发生成本/每件存货的年储存成本)
美国生产和库存控制协会APICS,American Production & Inventory Control Society 七.QS-9000中的术语
APQP Advanced Product Quality Planning and Control Plan,产品质量先期策划和控制计划PPAP Production Part Approval Process,生产件批准程序
FMEA Potential Failure Mode and Effects Analysis,潜在失效模式及后果分析
MSA Measure System Analysis,测量系统分析
SPC Statistical Process Control,统计过程控制
审核 Audit
能力 Capability
能力指数 Capability Indices
控制计划 Control Plans
纠正措施 Corrective Action
文件document ation
作业指导书 Job Instruction, work instruction
不合格品 Nonconformance
不合格 Nonconformity
每百万零件不合格数 Defective Parts Per Million, DPPM
预防措施 Preventive Action
程序Procedures
过程流程图 Process Flow Diagram, Process Flow Chart
质量手册Quality Manual
质量计划 Quality Plan
质量策划 Quality Planning
质量记录Quality Records
原始数据Raw Data
反应计划Reaction Plan
返修Repair。
返工Rework
现场Site
分承包方Subcontractors
产品product
质量quality
质量要求quality requirement
顾客满意customer satisfaction
质量管理体系quality management system
质量方针quality policy
质量目标quality objective
质量管理quality management
质量控制quality control
质量保证quality assurance
组织organization
顾客customer
供方supplier
过程process
服务service
设计与开发design and development:
特性characteristic
可追溯性trace ability
合格conformity
缺陷defect
纠正correction
让步concession
放行release
报废scrap
规范specification
检验inspection
试验test
验证verification
评审review
测量measurement
计数型数据Attributes Data
普通原因Common Cause
单值Individual
均值Mean
随机抽样Random Sampling
极差Range
特殊原因Special Cause
稳定性Stability
子组Subgroup
计量型数据Variables Data
变差Variation
固有变差Inherent Variation
总变差Total Variation
偏倚Bias
重复性Repeatability
再现性Reproducibility
稳定性Stability
线性Linearity
分辨率Resolution
过程更改Process change
质量功能展开QFD
过程特殊特性Special Process Characteristic
产品特殊特性Special Product Characteristic
外观项目Appearance Item
初始过程能力Preliminary Process Capability
材料清单Bill of Material
设计确认Design Validation
设计验证Design Verification
顾客的呼声Voice of the Customer
过程的呼声Voice of the Process
八.常用缩略词语
1、ES 工程规范 Engineering Specification
2、KCC 关键控制特性(GM)Key Control Characteristic
3、KPC 关键产品特性(GM)Key Product Characteristic
4、OEM 整车厂 Original Equipment Manufacturer
5、SC重要(特殊)特性 Significant(Special) Characteristic
6、ANOVA 方差分析法 Analysis of Variance
7、CFT 多方论证小组 Cross function Team
8、DFMEA 设计失效模式及后果分析 Design Failure Mode and Effects Analysis
9、DOE 试验设计 Design of Experiment
10、DVP&R 设计验证计划和报告 Design verification Plan and Report
11、FTC 试生产能力 First Time Capability
12、GR&R 量具的重复性和再现性Gage Repeatability and Reproducibility
13、PFMEA 过程失效模式及后果分析Process Failure Mode and Effect Analysis
14、SFMEA 系统失效模式及后是分析 System Failure Mode and Effect Analysis
15、QSR 质量体系要求 Quality System Requirement
16、QFD 质量功能展开 Quality Function Deployment
17、TGR 运行情况良好 Things Gone Right
18、TGW 运行情况不良 Things Gone Wrong
19、VE/VA 价值工程/价值分析value Engineering/value Analysis
20、BOM 物料清单 Bill of Material
21、Cpk 稳定过程的能力指数 Capability for stable process
22、LCL 下控制限 Lower Control Limit
23、UCL 上控制限 Upper Control Limit
24、LSL 工程规范下限 Lower Specification Limit
25、USL 工程规范上限 Upper Specification Limit
26、Ppk 性能指数 The performance index
27、MRB 物料评审 Material Review Board
28、PSW 零件提交保证书 Part Submission Warrant
29、X(—)--R图均值一极差图 Average-Range Chart
30、SRPC 供方要求产品更改 Supplier Request for Product Change
31、SREA 供方工程批准的要求 Supplier Request for Engineering Approval
32、IAA 临时批准授权 Interim Approval Authorization
33、AAR 外观件批准报告 Appearance Approval Report
34、PTR 试生产(报告) Production Trial Run (Report)
大梁girder 复式桁架complex truss 承受withstand 拉伸 stretch 屈曲 buckle 断裂brea k可行的feasible 地基土subsoil 面板deck 柔性的flexible 索 cable 桥台 abutment 传递 transmit 相交 intersect 推力 thrust The amount of bridge traffic 桥梁交通流量 jammed traffic 交通堵塞cost 费用financing 筹款Acquire 获取survey 勘察Tide 潮汐 Flood 洪水 current 水流 Bore 钻孔samples of soil and rock 岩土试样 Girder 大梁cantilever 悬臂梁truss 桁架arch 拱suspension 悬索location 地理位置 purposes 功用Span length 跨度Strength 强度harmony 协调 Alloy steels 合金钢 Steel wires 钢丝tension 拉力compression 压力bending 弯曲 shear 剪力torsion 扭矩Static loads 静载 vehicle 车辆impact 冲击vibration 振动Dynamic loads 动载live loads 活载tremors 地震震动Floating debris 浮物model testing 模型测试 Scale-down model test 缩尺模型试验Wind tunnel tests 风洞试验 Erect安装 cofferdams 围堰caissons 沉箱piles 桩上部结构 superstructure False work 脚手架 Floatation 浮运 cantilevering 悬 lifting 提升suspension悬吊 signs 标识 guardrails 护栏 Sea Works海洋工程maritime engineering 海事工程 Fishing ports渔港 marinas码头Reclamation and conservancy填海与保护 Maintenance 维护 estuaries河口Hydraulic水力的 Natural harbor天然海港 artificial harbor人工海港 Tidal cycle潮汐周期 scour冲刷 siltation淤积 breakwater防波堤 Secondary wave次生波 Reflected wave反射波 disturbances干扰 Bay海湾 jetty防波堤mole防波堤 locality地区 conservancy保护 ruin废墟 wharf码头alluvial冲积的 destructive破坏的 bar沙滩 anchorage锚地 littoral drift沿岸漂浮物 coast海岸 maintain保持 beach海滩 frailty弱点 craft工艺 indestructibility不可破坏性 implement执行outlast比…经久 durability耐久性 ingress入口 egress出口 underpin 支撑 dewater排水 hydraulic cement水硬性水泥 lime石灰dam水坝 retain保持 discharge流量 hydroelectric水电的
管道专业词汇 1. 阀门类 1.1 常用阀( 闸阀 Gate valve 截止阀(球心阀) Globe valve 节流阀 Throttle valve TRV 针型阀 Needle valve 角阀(角式截止阀)Angle valve Y 型阀(Y 型截止阀) Y-valve (Y-body globe valve 球阀 Ball valve 三通球阀3-Way ball valve 蝶阀 Butterfly valve 柱塞阀 Piston type valve 旋塞阀 Plug valve 三通旋塞阀 3-Way cock valve 旋塞 Cock 隔膜阀 Diaphragm valve ! 夹紧式胶管阀 pinch valve 止回阀 Check valve
1.2 其它阀 安全泄汽阀(安全阀) Safety valve SV 安全泄液阀(卸荷阀) Relief valve 安全泄压阀 Safety relief valve 罐底排污阀 Flush-bottom tank valve 波纹管密封阀 Bellow sealed valve 电磁阀Solenoid valve 电动阀 Electrically operated valve 气动阀 Pneumatic operated valve 低温用阀Cryogenic service valve 蒸汽疏水阀 Steam trap T 呼吸阀 Breather valve 减压阀 Reducing valve RV 3 控制阀、调节阀 Control valve 1.3不表明结构的阀 切断阀 Block valve;Shut-off valve;Stop valve 手动控制阀 Hand control valve HCV 调节阀 Regulating valve 快开阀 Quick opening valve 快闭阀 Quick closing valve 隔断阀 Isolating valve 三通阀 3-Way valve 夹套阀 Jacketed valve
管道专业术语常用英语 单词 Document number:BGCG-0857-BTDO-0089-2022
管道专业术语常用英语单词 在引进装置、涉外及中外合资技术改造工程的技术资料中,经常要接触到英语单词。由于管道安装涉及多项工程技术,而不从属于任何一项工程技术分支,故其技术性质有一定特殊性,不少英语词汇是在实践中逐渐形成的,借助一般科技英汉词典有时也难以找到它们的确切含意。现将管道安装工程中出现较多的单词整理列出,如果能熟悉这些单词,对阅英文图纸能收到事半功倍的效果。 一、专业名词术语 设计图 施工图 平面图 立面图 轴测图、透视图 详图、大样图、接点图 修改图竣工图图名 图号 比例 温度 设计温度 湿度 流量 流速 摄氏温度ayout; design final plan elevation isometric drawing;detail drawing record drawing as-completed drawing; as-built drawing title drawn No. scale temperature design temperature humidity flow flow velocity ? ? 毛重 净重 支座 支架 吊架 间距 跨距 焊接 焊缝 石棉水泥 接口 青铅接口 承口、大 头 插口、小 头 压力试验 水压试验 gross weight net weight saddle support cradle distance; clearance; spacing span welding weld; welding seam; bead asbestos-cement joint lead joint hub; bell; socket spigot pressure test hydraulic test
土建专业常用英文词汇(较完整版) A-frame A型骨架水泥cement 粉煤灰pulverized fuel ash 碎石broken stone cracked sto ne A-truss A型构架供应量supply 外加剂admixture cement additive abrasion 磨耗;磨蚀桩的平面布置pile layo ut 伸缩接头expansion joint 稀释沥青cut back bitumen abrasive cut-off machine 磨切机回填backfill 摩擦角an angle of frictio n 颗粒材料granular fill abrasive grinding machine 磨机(火石机) 颗粒层granular layer 立方码cubic yard abrasive particle 磨粒psi =po und/square inch 英制压力单位Psi具体单位是“lb/in2”, 就是“磅/平方英寸”路堤embankment 粗滤层coarse fliter abso rptio n 吸收ingredients 组成部分,成分,原料;要素,因素job mix formula 工地配合比abutment 桥台;拱座sampling 抽样frequency of test 检测频率 abutting end 邻接端co mpliance with 遵守符合co nform to 遵照符合acceleratio n 加速 in accordance with 依照与…一致wet cohesion 湿粘聚力Asphalt Binder 沥青胶泥 acceleratio n lane 加速车道potholes 坑洞locatio n 现场 acceleratio n pedal 加速器踏板reno mattress 石笼垫层splash pad 冲刷层geo-textile 土工布accelerato r 催凝剂;加速器;催化剂free drainage 自由排水 acceptance criteria 接受准则 access 通路;通道 access door 检修门;通道门 access lane 进出路径 access panel 检修门 access point 入口处;出入通道处 access ramp 入口坡道;斜通道 access ro ad 通路;通道 access shaft 竖井通道 access spiral loop 螺旋式回旋通道 access staircase 通道楼梯 access step 上落踏板;出入踏板 access tunnel 隧道通道 accessible roof 可到达的屋顶;有通道的屋顶 accessory 附件;配件 accident 事故;意外 accidental collapse 意外坍塌 acco mmodate 装设;容纳 accredited private laborato ry 认可私营实验室 accumulato r 储压器;蓄电池 accuracy limit 准确度极限 acetylene cylinder 乙炔气(风煤)樽 acid plant 酸洗设备;酸洗机 acid pump 酸液泵 acid tank 酸液缸 aco ustic co uplant 声耦合剂 aco ustic co upler 声耦合器 aco ustic lining 隔音板
第一部分必须掌握,第二部分尽量掌握 第一部分: 1 Finite Element Method 有限单元法 2 专业英语Specialty English 3 水利工程Hydraulic Engineering 4 土木工程Civil Engineering 5 地下工程Underground Engineering 6 岩土工程Geotechnical Engineering 7 道路工程Road (Highway) Engineering 8 桥梁工程Bridge Engineering 9 隧道工程Tunnel Engineering 10 工程力学Engineering Mechanics 11 交通工程Traffic Engineering 12 港口工程Port Engineering 13 安全性safety 17木结构timber structure 18 砌体结构masonry structure 19 混凝土结构concrete structure 20 钢结构steelstructure 21 钢-混凝土复合结构steel and concrete composite structure 22 素混凝土plain concrete 23 钢筋混凝土reinforced concrete 24 钢筋rebar 25 预应力混凝土pre-stressed concrete 26 静定结构statically determinate structure 27 超静定结构statically indeterminate structure 28 桁架结构truss structure 29 空间网架结构spatial grid structure 30 近海工程offshore engineering 31 静力学statics 32运动学kinematics 33 动力学dynamics 34 简支梁simply supported beam 35 固定支座fixed bearing 36弹性力学elasticity 37 塑性力学plasticity 38 弹塑性力学elaso-plasticity 39 断裂力学fracture Mechanics 40 土力学soil mechanics 41 水力学hydraulics 42 流体力学fluid mechanics 43 固体力学solid mechanics 44 集中力concentrated force 45 压力pressure 46 静水压力hydrostatic pressure 47 均布压力uniform pressure 48 体力body force 49 重力gravity 50 线荷载line load 51 弯矩bending moment 52 torque 扭矩53 应力stress 54 应变stain 55 正应力normal stress 56 剪应力shearing stress 57 主应力principal stress 58 变形deformation 59 内力internal force 60 偏移量挠度deflection 61 settlement 沉降 62 屈曲失稳buckle 63 轴力axial force 64 允许应力allowable stress 65 疲劳分析fatigue analysis 66 梁beam 67 壳shell 68 板plate 69 桥bridge 70 桩pile 71 主动土压力active earth pressure 72 被动土压力passive earth pressure 73 承载力load-bearing capacity 74 水位water Height 75 位移displacement 76 结构力学structural mechanics 77 材料力学material mechanics 78 经纬仪altometer 79 水准仪level 80 学科discipline 81 子学科sub-discipline 82 期刊journal ,periodical 83文献literature 84 ISSN International Standard Serial Number 国际标准刊号 85 ISBN International Standard Book Number 国际标准书号 86 卷volume 87 期number 88 专着monograph 89 会议论文集Proceeding 90 学位论文thesis, dissertation 91 专利patent 92 档案档案室archive 93 国际学术会议conference 94 导师advisor 95 学位论文答辩defense of thesis 96 博士研究生doctorate student 97 研究生postgraduate 98 EI Engineering Index 工程索引 99 SCI Science Citation Index 科学引文索引 100ISTP Index to Science and Technology Proceedings 科学技术会议论文集索引 101 题目title 102 摘要abstract 103 全文full-text 104 参考文献reference 105 联络单位、所属单位affiliation 106 主题词Subject 107 关键字keyword 108 ASCE American Society of Civil Engineers 美国土木工程师协会 109 FHWA Federal Highway Administration 联邦公路总署
9 主要术语说明 9.1 排水工程 sewerage engineering,wasterwater engineering 收集、输送、处理、再生和处置污水和雨水的工程。 9.2 排水系统 sewer system 收集、输送、处理、再生和处置污水和雨水的设施以一定方式组合成的总体。 9.3 排水制度 sewerage system 在一个地区内收集和输送城镇污水和雨水的方式。它有合流制和分流制两种基本方式。 9.4 排水设施 wastewater facilities 排水工程中的管道、构筑物和设备等的统称。 9.5 合流制 combined system 用同一管渠系统收集和输送城镇污水和雨水的排水方式。 9.6 分流制 separate system 用不同管渠系统分别收集和输送各种城镇污水和雨水的排水方式。 9.7 城镇污水 urban wastewater 城镇中排放各种污水和废水的统称,它由综合生活污水、工业废水和入渗地下水三部分组成。在合流制排水系统中,还包括被截留的雨水。 9.8 城镇污水系统 urban wastewater system 收集、输送、处理、再生和处置城镇污水的设施以一定方式组合成的总体。 9.9 城镇污水污泥 urban wastewater sludge 城镇污水系统中产生的污泥。 9.10 流污水 dry weather flow,DWF 合流制排水系统晴天时输送的污水。 9.11 生活污水 domestic wastewater,sewage 居民生活活动所产生的污水。主要是厕所、洗涤和洗澡产生的污水。 9.12 综合生活污水 comprehensive sewage 由居民生活污水和公共建筑污水组成。 9.13 工业废水 industrial wastewater 工业生产过程中产生的废水。 9.14 入渗地下水 infiltrated ground water 通过管渠和附属构筑物破损处进入排水管渠的地下水。 9.15 总变化系数 peak variation factor 最高日最高时污水量与平均日平均时污水量的比值。 9.16 径流系数 runoff coefficient 一定汇水面积内地面径流水量与降雨量的比值。 9.17 暴雨强度 rainfall intensity 在某一历时内的平均降雨量,即单位时间内的降雨深度。工程上常用单位时间单位面积内的降雨体积来表示。 9.18 重现期 recurrence interval 在一定长的统计期间内,等于或大于某降雨强度的降雨出现一次的平均间隔时间。 9.19 降雨历时 duration of rainfall
Part IV:Commonly Used Professional Terms of Civil Engineering development organization 建设单位 design organization 设计单位 construction organization 施工单位 reinforced concrete 钢筋混凝土 pile 桩 steel structure 钢结构 aluminium alloy 铝合金 masonry 砌体(工程)reinforced ~ 配筋砌体load-bearing ~ 承重砌体unreinforced ~非配筋砌体 permissible stress (allowable stress) 容许应力plywood 胶合板 retaining wall 挡土墙 finish 装修 finishing material装修材料 ventilation 通风 natural ~ 自然通风 mechanical ~ 机械通风 diaphragm wall (continuous concrete wall) 地下连续墙 villa 别墅 moment of inertia 惯性矩 torque 扭矩 stress 应力normal ~ 法向应力shear ~ 剪应力 strain 应变 age hardening 时效硬化 air-conditioning system空调系统 (air) void ration(土)空隙比 albery壁厨,壁龛 a l mery壁厨,贮藏室 anchorage length锚固长度 antiseismic joint 防震缝 architectural appearance 建筑外观 architectural area 建筑面积 architectural design 建筑设计 fiashing 泛水 workability (placeability) 和易性 safety glass安全玻璃 tempered glass (reinforced glass) 钢化玻璃foamed glass泡沫玻璃 asphalt沥青 felt (malthoid) 油毡 riveted connection 铆接 welding焊接 screwed connection 螺栓连接 oakum 麻刀,麻丝 tee三通管 tap存水弯 esthetics美学 formwork 模板(工程) shoring 支撑 batching 配料 slipform construction (slipforming) 滑模施工 lfit-slab construction 升板法施工 mass concrete 大体积混凝土 terrazzo水磨石 construction joint 施工缝 honeycomb蜂窝,空洞,麻面 piled foundation桩基 deep foundation 深基础 shallow foundation浅基础 foundation depth基础埋深 pad foundation独立基础 strip foundation 条形基础 raft foundation筏基 box foundation箱形基础 BSMT=basement 地下室 lift 电梯electric elevator lift well电梯井 escalator 自动扶梯 Poisson’s ratio 泊松比μ Young’s modulus , modulus of elasticity 杨氏模量,弹性模量E safety coefficient 安全系数 fatigue failure 疲劳破坏 bearing capacity of foundations 地基承载力bearing capacity of a pile 单桩承载力 two-way-reinforcement 双向配筋 reinforced concrete two-way slabs钢筋混凝土双向板 single way slab单向板 window blind 窗帘sun blind wind load 风荷载 curing 养护 watertight concrete 防水混凝土 white cement白水泥 separating of concrete混凝土离折segregation of concrete mortar 砂浆~ joint 灰缝 pilaster 壁柱 fire rating耐火等级 fire brick 耐火砖 standard brick标准砖
管道工程英文术语缩写(中英对照) 1.管子及管件 P 管子 Pipe EL 弯头 ELL 长半径弯头 ELS 短半径弯头 MEL 斜接弯头(虾米腰弯头) REL 异径弯头 T 三通 Tee LT 斜三通 RT 异径三通 R 异径管接头(大小头) Reducer CR 同心异径管接头(同心大小头) Concentric reducer ER 偏心异径管接头(偏心大小头) Eccentric reducer CPL 管箍 Coupling FCPL 双头管箍 Full coupling HCPL 单头管箍 Half coupling RCPL 异径管箍 Reducing coupling BU 内外螺纹接头 Bushing UN 活接头 Union HC 软管接头 Hose coupler SE 翻边短节 Stub end NIP 短节 Pipe nipple or straight nipple SNIP 异径短节 Swaged nipple CP 管帽(封头) Cap PL 管堵(丝堵) Plug BLK 盲板 Blank SB 8字盲板 Spectacle blind (blank) RP 补强板 Reinforcing pad
2.法兰 FLG 法兰 Flange WNF 对焊法兰 Welding neck flange SOF 平焊法兰 Slip-on flange SWF 承插焊法兰 Socket-welding flange T 螺纹法兰 Threaded flange LJ 松套法兰 Lapped joint flange REDF 异径法兰 Reducing flange BF 法兰盖(日法兰) Blind flange FSF 法兰密封面 Flange scaling FF 全平面 Flat face RF 凸台面 Raised face MFF 凹凸面 Male and female face LF 凹面 Female face LM 凸面 Male face RJ 环连接面 Ring joint face TG 榫槽面 Tongue and groove face TF 榫面 Tongue face GF 槽面 Groove face 3.垫片 G 垫片 Gasket NMG 非金属垫片 Non-metallic gasket AG 石棉垫片 Asbestos gasket RG 橡胶垫片 Rubber gasket TEG 聚四氟乙烯包复垫片 PTFE envelope gasket SMG 半金属垫片 Semimetallic gasket MJG 金属包垫片 Meta-jacket gasket SWG 缠绕式垫片 Spiral wound gasket MG 金属垫片 Metallic gasket FMG 金属平垫片 Flat metallic gasket SMSG 齿形金属垫片 Solid metal serrated gasket LER 透镜式金属环垫 Lens ring gasket OCR 八角形金属环垫 Octagonal ring gasket
常用造价英语词汇 估算/费用估算:estimate/cost estimate; 估算类型:types of estimate; 详细估算:是偏差幅度最小的估算,defined estimate; 设备估算:equipment estimate; 分析估算:analysis estimate; 报价估算:proposal estimate; 控制估算:control estimate; 初期控制估算:interim control estimate/initial control estimate 批准的控制估算:initial approved cost 核定估算:check estimate 首次核定估算:first check estimate 二次核定估算:production check estimate 人工时估算:man hour estimate 材料费用/直接材料费用:material cost/direct material cost 设备费用/设备购买费用:equipment cost/purchased cost of equipment 散装材料费用/散装材料购买费用:bulk material cost/purchased cost of bulk material 施工费用:construction cost 施工人工费用:labor cost/construction force cost 设备安装人工费用:labor cost associated with equipment 散装材料施工安装人工费用:labor cost associated with bulk materials 人工时估算定额:standard man-hours 施工人工时估算定额:standard labor man-hours 标准工时定额:standard hours 劳动生产率:labor productivity/productivity factor/productivity ratio 修正的人工时估算值:adjusted man-hours 人工时单价:man-hours rate 施工监督费用:cost of construction supervision 施工间接费用:cost of construction indirects 分包合同费用/现场施工分包合同费用:subcontract cost/field subcontract cost 公司本部费用:home office cost 公司管理费用:overhead 非工资费用:non payroll 开车服务费用:cost of start-up services 其他费用:other cost 利润/预期利润:profit/expected profit 服务酬金:service gains 风险:risk 风险分析:risk analysis 风险备忘录:risk memorandum 未可预见费:contingency 基本未可预见费:average contingency 最大风险未可预见费:maximum risk contingency 用户变更/合同变更:cilent change/contract change
A Type Wooden Ladder A字木梯 A-frame A型骨架 A-truss A型构架 Abandon 废弃 Abandoned well 废井 Aberration of needle 磁针偏差Abnormal pressure 异常压力abnormally high pressure 异常高压Abort 中止 abrasion 磨损 Abrasion surface 浪蚀面 abrasive cut-off machine 磨切机Abrasive Cutting Wheel 拮碟abrasive grinding machine 研磨机Abrasive Grinding Wheel 磨碟abrasive particle 磨料颗粒 Absolute address 绝对地址Absolute altitude 绝对高度Absolute damping 绝对阻尼Absolute deviation 绝对偏差Absolute flying height 绝对航高Absolute gravity 绝对重力 absolute permeability 绝对渗透率absolute porosity 绝对孔隙率absolute temperature 绝对温度absorbability 吸收性;吸附性absorption 吸收 abutment 桥墩 abutting end 邻接端 acceleration 加速 acceleration lane 加速车道Acceleration of gravity 重力加速度acceleration pedal 加速器踏板accelerator 催凝剂;加速器;催化剂acceptance criteria 接受准则 access 通路;通道 access door 检修门;通道门access lane 进出路径 access panel 检修门 access point 入口处;出入通道处access ramp 入口坡道;斜通道access road 通路;通道 access shaft 竖井通道 access spiral loop 螺旋式回旋通道access staircase 通道楼梯 access step 出入口踏步 access tunnel 隧道通道 accessible roof 可到达的屋顶accessory 附件;配件accident 事故;意外 accidental collapse 意外坍塌 accommodate 装设;容纳 accredited private laboratory 认可的私 人实验室 accumulator 储压器;蓄电池 accuracy limit 精度限制 acetylene cylinder 乙炔圆筒 Acetylene Hose 煤喉 Acetylene Regulator 煤表 acid plant 酸洗设备;酸洗机 acid pump 酸液泵 acid tank 酸液缸 acidic rock 酸性岩 acoustic couplant 声耦合剂 acoustic coupler 声音藕合器;音效藕 合器 acoustic lining 隔音板 acoustic screen 隔声屏 Acoustic wave 声波 acrylic paint 丙烯漆料(压克力的油漆) acrylic sheet 丙烯胶片(压克力的胶片) active corrosion 活性腐蚀 active earth pressure 主动土压力 active fault 活断层 active oxidation 活性氧化 actual plot ratio 实际地积比率 actuator 促动器;唧筒;激发器 adapt 改装 adaptor 适配器;承接器;转接器; addition 增设;加建 additional building works 增补建筑工 程 additional horizontal force 额外横向力 additional plan 增补图则(附加的平面 图) additional vent 加设通风口 additive 添加剂 Address 地址 adhesive 黏结剂;胶黏剂 adhesive force 附着力 Adhesive Glue 万能胶 Adhesive Reflective Warning Tape 反 光警告贴纸 adit 入口;通路;坑道口 adjacent construction 相邻建造物 adjacent level 相邻水平 adjacent site 相邻基地 adjacent street 相邻街道 adjoining area 毗邻地区 adjoining building 毗邻建筑物 adjoining land 毗邻土地 adjoining structure 毗邻构筑物 adjustable 可调校 Adjustable Wrench Spanner 昔士 adjuster 调节器 adjustment 调校;调整 Administrative Lawsuit 行政诉讼 Administrative Remedy 行政救济 admixture 掺合剂;外加剂 advance directional sign 前置指路标 志;方向预告标志 advance earthworks 前期土方工程 advance warning sign 前置警告标志 advance works 前期工程 aeration 曝气 aeration tank 曝气池 aerial 天线 Aerial mapping 航空测图 aerial photograph 航测照片 Aerial photography 航照定位 aerial rapid transit system 高架快速运 输系统 aerial ropeway 高架缆车系统 aerial view 鸟瞰图 aerofoil 翼型 aerosol 悬浮微粒;喷雾 aerosphere 大气圈 affix 贴附 aftercooler 后冷却器 afterfilter 后过滤器 aftershock 余震 agent 作用剂;代理人 aggradation 堆积 aggregate 骨材;集料;碎石 aggregate area 总面积 aggregate grading 骨材级配 aggregate superficial area 表面总面积 aggregate usable floor space 总楼地板 空间 agitator 搅拌器;搅动机 air bleeding 放气(空气渗出) air blower 鼓风机 air brake 气压制动器 Air chambor 气室 air circuit 空气回路 air circuit breaker 空气断路器 air cleaner 空气滤清器
工程英语-现场常见词汇
Owner/Client/Customer/Company 业主 Buyer 买方 Seller/vendor 卖方 Licensor 专利商 Licensee 专利受让方 Third party 第三方 Patent 专利 Property/proprietory technology 专利技术 Know-how 专有技术/知识 Contractor 承包商 Subcontractor分包商 Supplier 供货商 Sub-supplier 分供商 Manufacturer 制造厂家 Limited liability 有限责任 Joint venture 合资企业 Foreign-funded enterprise 外商独资企业Chairman 董事长 Board of director 董事会 President/ General manager 总经理 Legal representative 法人 Authorized representative 授权代表 Power of attorney 委托书 Signature 签字 Official seal公章 SEI-Sinopec Engineering Incorporated 中国石化工程建设公司 SSEC-Sinopec Shanghai Engineering Company 中国石化上海工程公司 SNEC-Sinopec Ningbo Engineering Company 中国石化宁波工程公司 TCC-Tianchen Chemical Engineering Company 中国天辰化学工程公司 HQCEC- Huanqiu Contracting & Engineering Corp.中国寰球化学工程公司 LPEC-Luoyang Petrochemical Engineering Company 洛阳石油化工工程公司 LDI-Sinopec Lanzhou Design Institute 中国石化兰州设计院 Chengda Chemical Engineering Company 中国成达化学工程公司 Hualu Engineering Company中国华陆工程公司Aker Kvaerner 克瓦纳(英) Bechtel 柏克德(美) AMEC 阿美科(英) Fluor 福陆(美) Foster Wheeler 福斯特惠勒(美) Technip 德西尼布(法) TR-Técnicas Reunidas联合技术公司(西班牙)JGC 日晖(日) Toyo 东洋(日) ABB Lummus ABB鲁玛斯(美) SINOPEC 中石化 CNOOC中海油 PETROCHINA 中石油EXXONMOBIL 埃克森美孚(美) SHELL 英荷壳牌 BP 英国石油(英) BASF 巴斯夫(德) Chevron 雪佛龙(美) Dow Chemical 陶氏化学(美) Sumitomo 住友(日) Saudi Aramco 沙特阿美(沙特) UOP 环球油品公司(美) Project/Work项目/工程 Rabigh Development Project 拉比格炼油项目 Location 未置/地点 Onshore/domestic 国内、国产 Offshore/overseas 国外、进口 Plant 装置 Facility 设施 Unit 装置/单元 Permanent/temporary work 永久工程/临时工程 Project/Plant/Job/Construction Site现场 Battery limit 界区/红线 Fence 围墙 Embankment/bund 围堤 Containment 围护 Retaining wall 挡土墙 Onsite/ISBL-Inside Battery Limit 场内 Offsite/OSBL-Outside Battery Limit 场外 Contract/agreement 合同/协议 Memorandum of Understanding 谅解备忘录 Letter of Intent意向书 Original 原件/正本 Copy 复印件/副本 Duplicate 一式两份 Triplicate一式三份 Quadruplicate一式四份 Quintuplicate一式五份 Sextuplicate一式六份 Septuplicate一式七份 Octuplicate一式八份 Nonuplicate一式九份 Decuplicate一式两份 Blueprint 蓝图 Distribution 分发 Holder 持有人 Transmittal 文件传送单 Controlled copy 受控版本 Uncontrolled copy 非受控版本 Edition 版本 Revision 版次、修订版 Terms and conditions 条款 General conditions 通用条款 Special conditions 特殊条款 Sign/Execute/Enter into 签署 Come into force/effect生效 Effective Date 生效日期 Contract term 和同期 Expiration 届满、到期 Termination 提前终止 Obligation 义务 Liability(债务)责任 Performance 执行、业绩 Breach 违约 Default 失职 Negligence 疏怠职责 Remedy 救济、补救 Compensation 补偿 Performance guarantee 性能保证 Waiver 放弃/弃权 Severability 可分割性 Modification/Change/Variation/Change Order 变更/ 变更单Amendment 修订 Supplement/Addition/Addendum增加/增补 Deletion删除 Governing law 管辖法律 Assignment/transfer 转让 Insurance 保险 Worker’s compensation 工伤责任险 Employer’s liability 雇主责任险 All-loss liability 一切损失险 Policy保单 Insurance certificate 保险证书/凭证 QA-Quality Assurance质保 QC/Quality Control 质控 Procurement and supply 采购供应 Schedule and progress control 工期与进度控制 Reporting 报告 Acceptance 验收 Spare part 备件 Rework 返工 Repair 修补/修复/修理 Replacement 更换 Substitute 替换/代用 Warranty Period 保质期 Claim 索赔 HSE-Health, Safety and Environmental 健康、安全 与环境 HSSE- Health, Safety, Security & Environmental 健 康、安全与环境 Taxes 税款 Liquidated damages 违约赔偿 Invoice 发票 Payment 付款 Intellectual property right 知识产权 Confidentiality 保密 Disclosure 披露 Prior oral/written consent 事先口头/书面同意 Publication 公开/宣传 Suspension 停工 Take-over/hand-over 交工 Force Majeure 不可抗力 Lien 留置(权) 2