洗碗机说明书
en Table of contents
Safety instructions . . . . . . . . . . . . . . . . . 4 Before you switch ON the appliance . . 4 Delivery . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation . . . . . . . . . . . . . . . . . . . . . . 4 In daily use . . . . . . . . . . . . . . . . . . . . . 4 Children in the household . . . . . . . . . . 4 Door lock . . . . . . . . . . . . . . . . . . . . . . 4 Damage . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . 5 Getting to know your appliance . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . 5 Appliance interior . . . . . . . . . . . . . . . . 5 Water softening system . . . . . . . . . . . . . 6 Setting . . . . . . . . . . . . . . . . . . . . . . . . . 6 Water hardness table . . . . . . . . . . . . . 6 Special salt $ . . . . . . . . . . . . . . . . . . . . . 7 Using special salt . . . . . . . . . . . . . . . . 7 Detergents with salt component . . . . . 7 Switching off water softening system . 7 Rinse aid % . . . . . . . . . . . . . . . . . . . . . . . 8 Setting amount of rinse aid . . . . . . . . . 8 Switching off rinse-aid refill indicator . . 8 Utensils . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Not suitable . . . . . . . . . . . . . . . . . . . . . 9 Glass and utensil damage . . . . . . . . . 9 Loading the dishwasher . . . . . . . . . . . 9 Unloading the dishwasher . . . . . . . . . . 9 Basket . . . . . . . . . . . . . . . . . . . . . . . . . 9 Cutlery basket . . . . . . . . . . . . . . . . . . . 9 Folding spikes . . . . . . . . . . . . . . . . . . 10 Height of utensils . . . . . . . . . . . . . . . 10 Detergent . . . . . . . . . . . . . . . . . . . . . . . . 10 Adding detergent . . . . . . . . . . . . . . . 11 Combination detergent . . . . . . . . . . . 11 Overview of programmes . . . . . . . . . . 12 Programme selection . . . . . . . . . . . . 12 Information for test institutes . . . . . . . 12 Additional options . . . . . . . . . . . . . . . . 13 Express Wash/ Speed Perfect (VarioSpeed) . . . . . . . . . . . . . . . . . . . 13 Intensive zone . . . . . . . . . . . . . . . . . . 13 Hygiene . . . . . . . . . . . . . . . . . . . . . . . 13 Half load . . . . . . . . . . . . . . . . . . . . . . 13 Extra drying . . . . . . . . . . . . . . . . . . . . 13Washing the dishes . . . . . . . . . . . . . . . 13 Programme data . . . . . . . . . . . . . . . 13 Aqua sensor . . . . . . . . . . . . . . . . . . 13 Switching on the appliance . . . . . . . 13 Timer programming . . . . . . . . . . . . . 13 End of programme . . . . . . . . . . . . . . 14 Switching off the appliance . . . . . . . 14 Interrupting the programme . . . . . . . 14 Terminating the programme . . . . . . 14 Changing the programme . . . . . . . . 14 Intensive drying . . . . . . . . . . . . . . . . 14 Maintenance and care . . . . . . . . . . . . . 15 Overall condition of the machine . . . 15 Special salt and rinse aid . . . . . . . . 15 Filters . . . . . . . . . . . . . . . . . . . . . . . . 15 Spray arm . . . . . . . . . . . . . . . . . . . . 16 Troubleshooting . . . . . . . . . . . . . . . . . 16 Waste water pump . . . . . . . . . . . . . . 17 ... when the appliance is switched on 17 ... on the appliance . . . . . . . . . . . . . 17 ... during the wash cycle . . . . . . . . . 18 ... on the utensils . . . . . . . . . . . . . . . 18 Customer service . . . . . . . . . . . . . . . . . 19 Installation . . . . . . . . . . . . . . . . . . . . . . 20 Safety instructions . . . . . . . . . . . . . . 20 Delivery . . . . . . . . . . . . . . . . . . . . . . 20 Technical specifications . . . . . . . . . . 20 Installation . . . . . . . . . . . . . . . . . . . . 20 Waste-water connection . . . . . . . . . . 21 Fresh water connection . . . . . . . . . . 21 Electrical connection . . . . . . . . . . . . 21 Removing the appliance . . . . . . . . . 21 Transportation . . . . . . . . . . . . . . . . . 21 Protection against frost (Emptying the appliance) . . . . . . . . . . . . . . . . . . . . 21 Waste disposal . . . . . . . . . . . . . . . . . . . 22 Packaging . . . . . . . . . . . . . . . . . . . . 22 Old appliances . . . . . . . . . . . . . . . . 22
en
4
Children from 8 years of age or people whose physical, sensory or mental abilities or their lack of experience or knowledge prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person.
Before you switch ON the appliance
Please read the operating and installation instructions carefully. They contain
important information on how to install, use and maintain the appliance.
Retain all documents for subsequent use or for the next owner.
Delivery
–Check the packaging and dishwasher
immediately for damage caused in transit. Do not switch on a damaged appliance, but contact your supplier.–Please dispose of the packaging
material in an environmentally friendly manner.
–Do not let children play with packaging
and its parts. There is a risk of
suffocation from collapsible boxes and film.
Installation
Read the “Installation” chapter to learn how to install and connect the appliance correctly.
In daily use
–This appliance is intended for use in
the home and the home environment.–Use the dishwasher
only in the household and only for its designed purpose: for washing domestic dishes.
–Children or people whose physical,
sensory or mental abilities prevent them from using the appliance safely must not use this appliance without supervision or instruction by a responsible person.
–Do not lean or sit on the open door.
The appliance could tip.
–Please note that free-standing
appliances may tip over if the baskets are overloaded.
–Do not add any solvents
to the washing chamber. Danger of explosion!–Open the door carefully
when the programme is still running. There is a risk of hot water spraying out of the appliance.
–Read and observe the safety
information and instructions
for use on the packaging for cleaning and rinsing agents.
m Warning
Knives and other utensils with sharp points must be placed in the cutlery basket with the points downwards or horizontally on the knife shelf *.
* depending on model
Children in the household
–If fitted, use the childproof lock. An
exact description can be found in the back of the envelope.
–Do not allow children to play with or
operate the appliance.
–Keep children away from detergents
and rinse aid. These may cause chemical burns in the mouth, throat and eyes or asphyxiation.
–Keep children away from open
dishwasher. The water in the rinsing compartment is not drinking water and could contain detergent residue.
Childproof lock (door lock) *
The description of the childproof lock is at the back in the envelope.* depending on model
Safety instructions
en
5
Damage
–The appliance may be repaired and
opened up by a technician only. To do this, disconnect the appliance from the power supply. Pull out the mains plug or switch off the fuse. Turn off the tap.–If the fascia is damaged (cracks, holes,
broken buttons), do not operate the appliance. Pull out the mains
plug or switch off the fuse. Turn off the tap, call customer service.
Disposal
–Make redundant appliances unusable
to prevent subsequent accidents. –Dispose of the appliance in an
environmentally friendly manner.
m Warning
Children could become locked in the appliance (risk of suffocation) or find themselves in other dangerous situations.Therefore: Pull out the mains plug, sever and dispose of the power cord. Destroy the door lock so that the door can no longer be closed.
Diagrams of the control panel and the interior of the appliance can be found in the envelope at the front.
Individual positions are referred to in the text.
Control panel
* depending on model
** Number depending on model
Appliance interior
Getting to know your appliance
(ON/OFF switch
0Programme selector 8START button
@Timer programming *H Additional options **P Rinse aid refill indicator X Salt refill indicator
`Display “Check water supply”h Dry display
)"
Cleaning display
1"Spray arm 1*Filters
12Dispenser for special salt 1:Cutlery basket 1B Basket
1J Dispenser for rinse aid 1R Detergent dispenser
1Z Lock for detergent dispenser 1b
Rating plate
en
6
To ensure good washing results, the dishwasher requires soft water, i.e.
containing low amounts of lime, otherwise white limescale will be deposited on the utensils and inner container.
Tap water above a specific degree of water hardness must be softened, i.e. descaled, for use in a dishwasher. Water is softened with special salt in the water softening system of the dishwasher.The setting and therefore the required amount of salt depends on the degree of hardness of your tap water (see table).
Setting
The amount of salt dispensed can be set in 4 stages
depending on the hardness of your water. Accordingly 0, 1, 2 or 3 displays are lit (see table). Factory setting: 1.–Find out about the hardness
value of your tap water. Your water utility company will help you with this.–Setting can be found in the water
hardness table.–Close the door.
–Switch on ON/OFF switch (.
The Cleaning display )" flashes.–Press and hold down the START
button 8.
–Rotate programme selector 0 until
the salt refill indicator X flashes.–Release button.
The salt refill indicator X flashes and the display “Check water supply” ` are lit (= Setting 1).To change the setting:
–Rotate programme selector 0 until
the required setting has been selected.–Press START button 8.
The salt refill indicator X goes out. The selected setting is saved.
Water hardness table
Water softening system
en
7
Using special salt
Always refill with special salt immediately before switching on the appliance. This ensures that overrun special salt solution is immediately washed out and does not corrode the rinsing tank.
–Open the screw-type cap of the
compartment 12.
–Fill the tank with water (only required
when switching on the appliance for the first time).
–Then add dishwasher salt (not table
salt or tablets).
The water is displaced and runs out. As soon as the salt refill indicator X on the fascia is lit, top up the salt.
* depending on model
Using detergents with salt component
If combined detergents with a salt
component are used, salt can usually be omitted up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l). If the water hardness is over 21° dH, special salt must be used.
S witching off salt refill indicator/water softening system
If the salt refill indicator X is impaired (e.g. when using combined detergents containing salt component), it can be switched off.
–Proceed as described under “Adjusting
the water softening system” and select setting 0.
The water softening system and salt refill indicator are now switched off.
n Caution
Never fill the salt dispenser with detergent. You will destroy the water softening system.
Special salt $
en
8
As soon as the rinse-aid refill indicator P is lit on the fascia, there is still a rinse-aid reserve of 1 – 2 rinsing processes. Refill with rinse aid.
The rinse aid is required for stain-free utensils and clear glasses. Use only rinse aid for domestic dishwashers.
Combined detergents with rinse-aid component may be used up to a water hardness of 21° dH (37° fH, 26° Clarke, 3.7 mmol/l) only. If the water hardness is over 21° dH, rinse aid must be used.–Open the dispenser 1J by pressing
and lifting the plate on the cover.
–Carefully pour rinse aid up to the max.
mark in the filler opening.
–Close cover until it clicks shut.
–To prevent excessive foam formation
during the next rinse cycle, remove any rinse aid which has run over with a cloth.
Setting amount of rinse aid
The amount of rinse aid dispensed can be set in 4 stages. Accordingly 0, 1, 2 or 3 displays are lit (see water hardness table). Factory setting: 2.
Do not change the amount of rinse aid unless streaks (select lower
setting) or water stains (select higher setting) are left on the utensils.–Close the door.
–Switch on ON/OFF switch (.
The Cleaning display )" flashes.–Press and hold down the START
button 8.
–Rotate programme selector 0 until
the rinse aid refill indicator P flashes.–Release button.
The rinse aid refill indicator P flashes and the displays h and ` are lit (= Setting 2).
To change the setting:
–Rotate programme selector 0 until
the required setting has been selected.–Press START button 8.
The rinse-aid refill indicator P goes out. The selected setting is saved.
Switching off rinse-aid refill indicator
If the rinse-aid refill indicator P is impaired (e.g. when using combined detergents containing rinse-aid component), it can be switched off.
–Proceed as described under “Setting
amount of rinse aid” and select setting 0.
The rinse aid refill indicator P is now switched off.
Rinse aid
%
en
9
Not suitable
–Cutlery and utensils made of wood. –Delicate decorative glasses, craft and
antique utensils. These decors are not dishwasher-proof.
–Plastic parts not resistant to heat.–Copper and tin utensils.
–Utensils which are soiled with ash, wax,
lubricating grease or ink.
Aluminium and silver parts have a
tendency to discolour and fade during the wash cycle. Even some types of glass (e.g. crystal glass objects) may turn cloudy after many wash cycles.
Glass and utensil damage
Causes:
–Glass type and glass production
process.
–Chemical composition of the detergent.–Water temperature of the wash
programme.Recommendation:
–Use only glasses and porcelain which
the manufacturer designates as dishwasher-proof.
–Use a detergent which protects
utensils.
–Take glass and cutlery out of the
dishwasher as soon as possible after the programme ends.
Loading the dishwasher
–Remove large food remnants. It is not
necessary to prerinse utensils under running water.
–Place the utensils so that
–they are secure and cannot tip over.–all utensils with their openings face
down.
–parts with curves or indentations
are at an angle, thereby allowing water to drain.
–the spray arm 1" can still rotate
freely.
Very small utensils should not be washed in the dishwasher, as they can easily fall out of the utensils basket 1B .
Unloading the dishwasher
Hot utensils are sensitive to shock! Therefore, when the programme ends, leave the utensils to cool down in the dishwasher until they can be handled.Note
When the programme ends, water droplets can still be seen inside the appliance. This does not affect the drying of the utensils.
B asket 1B
Cutlery basket
You should always place cutlery unsorted with the points downwards.
To prevent injuries, place long, pointed implements and knives on the knife shelf.
Utensils
en
10
F olding spikes *
* depending on model
The spikes can be folded down to improve arrangement of pans, bowls and glasses.
Height of utensils
The maximum height of the utensils is 28 cm.
You can use tablets as well as powder or liquid detergents for dishwashers, but never use washing up liquid. The dosage can be individually adjusted with powder or a liquid detergent according
to the degree of soiling. Tablets contain an adequately large amount of active
ingredients for all cleaning tasks. Modern, powerful detergents predominantly use a low-alkaline formulation with phosphate and enzymes. Phosphates bond the lime in the water. Enzymes break down starch and remove protein. Phosphate-free detergents are less frequent. These have a slightly weaker lime bonding capacity and require a higher dosage. To remove coloured stains (e.g. tea, tomato sauce), oxygen-based bleaching agents are usually used.Note
To ensure a good washing result, always follow the instructions on the detergent packaging!
If you have further questions, we recommend that you contact
the detergent manufacturers’ helpline.
m Warning
Read and observe the safety information and instructions for use on the packaging
for cleaning and rinsing agents.
Detergent
en
11
Adding detergent
–If the detergent dispenser 1R is still
closed, press the lock 1Z to open the detergent dispenser.
Pour detergent into the dry detergent dispenser 1R only (insert tablet flat, not on its edge).
Dosage: see manufacturer’s instructions on the packaging. The graduated detergent
dispenser 1R helps you add the correct amount of powder or liquid detergent.
–Close the cover on the detergent
dispenser by sliding it up until the lock engages without difficulty.
The detergent dispenser opens automatically at the optimum time depending on the programme. The powder or liquid detergent is distributed in the appliance and is dissolved. The tablet falls into the appliance and dissolves.
Tip
If the utensils are only lightly soiled, slightly less than the indicated amount of detergent is usually adequate.
Suitable detergents and care products can be purchased online via our website or via customer service (see back page).
Combination detergent
Apart from conventional detergents (Solo), a number of products are offered with additional functions. These products contain not only the detergent but also rinse-aid and salt replacement substances (3in1) and, depending on the combination (4in1, 5in1, etc.), additional components such as glass protection or stainless steel cleaner. Combination detergents function only up to a specific degree of hardness (usually 26° Clarke). Over this limit salt and rinse-aid must be added. As soon as combined detergents
are used, the rinse programme is adjusted automatically to ensure the best possible rinsing and drying result.
Notes
–You will obtain optimum rinsing
and drying results by using solo
detergents and applying salt and rinse aid separately.
–If programmes are short, tablets
may not have full cleaning effect due to different dissolving properties
and there may even be undissolved detergent residue. It is recommended to use washing powder for these programmes.
–Even if the rinse-aid and/or salt refill
indicator is lit, the rinse programme will run correctly with combined detergents.
–If using detergents in a water-soluble
protective cover: Take hold of the cover with dry hands only and put the detergent into an absolutely
dry detergent dispenser only, otherwise the detergent may stick.
–If you switch from combined
detergents to solo detergents, ensure that the water softening system and amount of rinse aid have been set to the correct value.
en
12
The max. possible number of programmes is illustrated in this overview.
The corresponding programmes for your appliance can be found on the fascia.Programme selection
You can select a suitable programme according to the type of utensils and degree of soiling.
Information for test institutes
Test institutes receive the information for comparability tests (e.g. according to EN60436).
These are the conditions for conducting the tests, however these are not the results or consumption values. Request by e-mail to:
dishwasher@https://www.sodocs.net/doc/db1148895.html, The product number (E no.) and the production number (FD) are required
which you can find on the rating plate 1b on the appliance door.
Overview of programmes
en
13
* depending on model
Additional options can be set with the buttons H .
? Express Wash/ Speed Perfect/
(VarioSpeed) *
This function can reduce the running time by approx. 20% to 50% depending on the selected rinse programme. To obtain optimum cleaning and drying results at a reduced running time, water and energy consumption are increased.
? Intensive zone *
Perfect for a mixed load. You can wash very soiled pots and pans in the lower basket together with normally soiled utensils in the upper basket. The spray pressure in the lower basket is intensified, the rinsing temperature is increased slightly.
· Hygiene *
The temperature is increased during the cleaning process. This increases the hygiene status. This additional option is ideal for cleaning e.g. chopping boards and baby bottles.
§ Half load *
If you have only a few items to wash (e.g. glasses, cups, plates), you can switch to “half load”. This will save water, energy and time. It is recommended to put a little less detergent in the detergent dispenser than for a full load.
? Extra drying *
An increased temperature during the final rinse and an extended drying phase ensure that even plastic parts dry better. There is a slight increase in the energy consumption.
Programme data
The programme data (consumption values) can be found in the summary of instructions. This data refers to normal conditions and the water hardness set value 2. Different influencing factors such as water temperature or mains pressure may result in deviations.
Aqua sensor *
* depending on model
The Aqua sensor is an optical measuring device (light barrier) which measures the turbidity of the rinsing water.
The Aqua sensor is used according to the programme. If the Aqua sensor is active, “clean” rinsing water can be transferred to the next rinse bath and water consumption can be reduced by 2–4 litres. If the turbidity is greater, the water is drained and is replaced with fresh water. In the automatic programmes the temperature and running time can also be adjusted to the degree of soiling.
Switching on the appliance
–Turn on the tap fully.–Close the door.
–Switch on ON/OFF switch (.
The Cleaning display )" flashes.–Rotate programme selector 0
to the required programme.–Press START button 8.
The Cleaning display )" is lit. The programme starts running.
T imer programming *
* depending on model
You can delay the start of the programme by 3, 6 or 9 hours.
–Switch on ON/OFF switch (.
–Keep pressing the Preselected starting
time button @ until the appropriate display 3h, 6h or 9h is lit.
–Press START button 8, timer
programming is activated.
Additional options
Washing the dishes
en
14
–To delete the preselected starting time,
keep pressing the Preselected starting time button @ until none of the displays 3h, 6h or 9h is lit.
You can change your programme selection at any time until the programme starts.
End of programme
The programme has ended when neither of the two displays h or )" is lit.Note
To save energy, the dishwasher
automatically switches off after the end of the programme.
Switching off the appliance
Short time after the end of the programme:–Switch off ON/OFF switch (.
–Turn off the tap (not applicable if Aqua-Stop fitted).
–Remove the utensils when they have
cooled down.Note
When the programme ends, leave
the appliance to cool down a while before opening it. This will prevent steam from escaping and causing long-term damage to your built-in furniture.
Interrupting the programme
–Switch off ON/OFF switch (.
The LEDs go out. The programme is saved.
If the door was opened on an
appliance which has a warm water connection or is heated, first leave the door ajar for several minutes and then close. Otherwise, expansion (pressure) may cause the appliance door to
spring open or water to run out of the appliance.
–To continue the programme, switch on
the ON/OFF switch ( again.
T erminating the programme (Reset)
–Press START button 8 for
approx. 3 sec. until all displays go out.–The remaining programme sequence
for draining the residual water takes approx. 1 minute.
Changing the programme
When the START button 8 has been pressed, the programme cannot be changed.
The only way a programme can be
changed is by Cancel programme (Reset).
Intensive drying
The final rinse uses a higher temperature which improves the drying result.
The running time may increase slightly. (Caution if utensils are delicate!)–Close the door.
–Switch on ON/OFF switch (.
The Cleaning display )" flashes.–Press and hold down the START
button 8.
–Rotate programme selector 0 until
the “Check water supply” display ` flashes.
–Release button.To change the setting:
–By rotating the programme selector
0, you can switch on intensive drying (Dry display h
is lit) or switch off intensive drying (Dry display h is not lit).–Press START button 8.
The setting is saved.
en
15
A regular inspection and maintenance of your machine will help to prevent faults. This saves time and prevents problems.
Overall condition of the machine
–Check spray arm for grease and
limescale deposits.If you find such deposits:
–Fill detergent dispenser with detergent.
Start the appliance without utensils in the programme with the highest rinsing temperature.
Clean the appliance with detergents/
appliance cleaners which are particularly suitable for use with dishwashers.
–Regularly clean door seal with a damp
cloth.
Never use a steam cleaner to clean your dishwasher. The manufacturer is not liable for any consequential damage.
Regularly wipe the front of the appliance and fascia with a damp cloth; water and a little washing up liquid are adequate. Do not use sponges with a rough surface or abrasive detergents, as these could scratch the surfaces.
Stainless steel appliances: To prevent corrosion, avoid using sponge cloths or wash them out thoroughly several times before using for the first time.
m Warning
Never use other chlorinated household detergents! Health hazard!
Special salt and rinse aid
–Check the refill indicators X and
P . If required, refill salt and/or rinse aid.
Filters
The filters 1* keep large foreign objects in the rinsing water away from the pump. These foreign objects may occasionally block the filters.
The filter system consists of a coarse filter, a flat fine filter and a microfilter.
–After each washing cycle check the
filters for residue.
–Unscrew filter cylinder as illustrated
and take out filter system.
–Remove any residue and clean filters
under running water.
–Re-install filter system in reverse
sequence and ensure that the arrow marks are opposite each other after closing the filter system.
Maintenance and care
en
16
Spray arm
Limescale and dirt from the rinsing water may block nozzles and the bearing assemblies of the spray arm 1".
–Check outlet nozzles on the spray arm
for blockages.
–Remove the spray arm upwards.
–Clean the spray arm under running
water.
–Lock the spray arm into position.
The majority of faults which could occur in daily operation can be rectified by the user. This ensures that the appliance is quickly available for use again. The
following overview will help you locating the causes and gives helpful advise to eliminate them.
Note
If the appliance stops during dishwashing or does not start for no obvious reason, first run the Abort programme function (Reset).
(See chapter entitled “Dishwashing”)
m Warning
Don’t forget: Repairs may be carried out by technicians only. If a component has to be replaced, ensure that only original spare parts are used. Improper repairs or use of non-original spare parts may cause considerable damage and put the user at
considerable risk.
Troubleshooting
en
17
Waste water pump
Large food remnants in the rinsing water not retained by the filters may block the waste water pump. The rinsing water is then not pumped out and covers the filter. In this case:
–First disconnect the appliance from the
power supply.
–Remove the filters 1*.
–Scoop out water, use a sponge if
required.
–Loosen screws on the pump cover
(Torx T 20) and pull off.
–Check inner compartment and remove
any foreign objects.
–Place pump cover in the original
position, press down and screw tight.–Install filters.
... when the appliance is switched on
The appliance does not start.–The mains fuse has tripped.
–The appliance plug has not been
inserted.
–The appliance door has not been shut
properly.
... on the appliance
Spray arm rotates sluggishly.–Spray arm blocked.
The door is difficult to open. *
–Child-proof lock is activated. The
deactivation instructions are at the back in the envelope.* depending on model
Cover on the detergent dispenser cannot be closed.
–Detergent dispenser overfilled or
mechanism blocked by sticky detergent residue.
Detergent residue in the detergent dispenser.
–Dispenser was damp when filled.
“Check water supply” display ` lights up.
–Tap turned off.
–Water supply interrupted.–Supply hose kinked.
–Filter in the water supply blocked.
–Switch off the appliance and pull
out the mains plug. –Turn off the tap.
–Clean filter in the supply hose.
–Reconnect power supply. –Turn on the tap.
–
Switch on the appliance.
en
18
–Water is left in the appliance at the end
of the programme.–Waste water hose
is blocked or kinked.
–Waste water pump blocked,
cover on the waste water pump is not locked in position (see Waste water pump).–Filters blocked.
–The programme has not yet ended.
Wait until programme
ends or implement “Reset” function.
The “Check water supply” display ` flashes rapidly.
–Water in the safety system.
–Switch off the appliance and pull
out the mains plug. –Turn off the tap.
–Call customer service.
Refill indicator for salt X and/or rinse-aid P is not lit.
–Refill indicator/s switched off.–Adequate salt/rinse-aid available.
Refill indicator for special salt X is lit.–No salt.
Refill with special salt.
–Sensor does not detect salt tablets.
Use different special salt.
... during the wash cycle
Unusual foam formation.
–Handwash liquid in the rinse aid
dispenser.
Spilled rinse aid causes excessive frothing, therefore please remove with a cloth.
Appliance stops during the wash cycle.–Power supply interrupted.–Water supply interrupted.
Filling valves making striking noises
–Caused by the installation of the water
line and has no effect on the function of the machine. Remedial action is not possible.
Knocking/rattling noise during rinsing –Spray arm is striking utensils.–Utensils not arranged correctly.
... on the utensils
Food residue on the utensils.
–Utensils placed too closely together,
utensils basket overfilled.–Too little detergent.
–Rinse programme too weak.–Spray arm rotation obstructed.–Spray arm nozzles blocked.–Filters blocked.
–Filters incorrectly inserted.–Waste water pump blocked.
Tea or lipstick residue is not completely removed.
–The detergent has an inadequate
bleaching effect.
–Too low rinsing temperature.–Too little/unsuitable detergent.White stains on the utensils/glasses remain milky.
If phosphate-free detergents are used with hard tap water, white deposits may be deposited more easily on utensils and the container walls.
–Too little/unsuitable detergent.–Too weak programme selected.–No/too little rinse aid.–No/too little special salt.
–Water softening system set to the
wrong value.
–Salt dispenser lock not fastened.Contact the detergent manufacturer, in particular if:
–the utensils are very wet at the end of
the programme.–limescale forms.
Dull, discoloured glasses, film cannot be washed off.
–Unsuitable detergent.
–Glasses not dishwasher-proof.
Streaks on glasses and cutlery, glasses have metallic appearance.–Too much rinse aid.Plastic parts discoloured.
–Too little/unsuitable detergent.–Too weak programme selected.
en
19
Rust spots on the cutlery.–Cutlery not rust-resistant.
–Salt content in the rinsing water too
high, as salt dispenser lock not
fastened firmly or salt was spilled while being refilled.Utensils not dry.
–Appliance door opened too early and
utensils taken out too early.
–Programme selected without drying.–Too little/unsuitable rinse aid.–Activate intensive drying.
–The combined detergent used has
a poor drying performance.
Use rinse aid (see Rinse aid chapter for setting).
If the advice given does not resolve your problem, please contact your customer service. Contact details can be found on the back cover of this instruction manual or in the enclosed customer service list. When calling , please quote the appliance number (1) and the production date
(FD = 2) which can be found on the rating plate 1b on the appliance door.
Rely on the expertise of the
manufacturer. Call us to ensure that the repair will be carried out by fully-trained service engineers, who are equipped with original spare parts for your appliance.
Customer service
en
20
The dishwasher must be connected correctly, otherwise it will not function properly. The specifications for the inlet and outlet as well as the electrical
connected loads must correspond with the required criteria as specified in the
following paragraphs or in the installation instructions.
Install the appliance in the correct sequence:
–Checking appliance on delivery –Installing the appliance –Waste water connection –Fresh water connection –Electrical connection
Safety instructions
–Install and connect the appliance
according to the installation and assembly instructions.
–Prior to installation, disconnect the
dishwasher from the power supply.–Ensure that the protective conductor
system of the domestic supply has been correctly installed.
–The electrical connection conditions
must correspond with the
specifications on the dishwasher rating plate 1b .
–If the power cord of this appliance is
damaged, it must be replaced with a particular power cord.
To prevent injury, the power cord may be replaced by customer service only.–If the dishwasher is installed in a high-sided unit, the unit must be secured properly.
–Do not install the appliance near heat
sources (radiators, heat storage tanks, cookers or other appliances which generate heat) and do not install under a hob.
–After installing the appliance, ensure
that the plug is easily accessible.
–Some models:
The plastic housing on the water
connection contains an electric valve, the connecting cables are in the supply hose. Do not cut through this hose, do not immerse the plastic housing in water.
Delivery
Your dishwasher has been checked
thoroughly in the factory to ensure that it is in working order. This may cause small water stains. These will disappear after the first wash cycle.
Technical specifications
Weight:max. 24 kg Voltage:
220–240 V, 50 Hz or 60 Hz Connected load:2.0–2.4 kW Fuse:
10/16 A (UK 13A)Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve ahead.Inlet rate:
minimum 10 litres/minute Water temperature:
cold water; hot water max. temperature 60 °C.
Installation
The required installation dimensions can be found in the installation instructions. Level the appliance. Ensure that the
appliance is situated securely on the floor.–The appliance can easily be
installed in a fitted kitchen between wooden and plastic walls.
Installation
en
21
Waste-water connection
–The required work sequence can be
found in the installation instructions. If required, fit a siphon with an drainage connection.
–Connect the waste-water hose to the
drainage connection of the siphon with the enclosed parts.
Ensure that the drainage hose is not kinked, crushed or twisted and that there is no cover plate in the drainage to prevent the waste water from flowing out!
Fresh water connection
–Connect the fresh-water connection to
the tap according to the installation instructions with the enclosed parts.Ensure that the fresh-water connection is not kinked, crushed or twisted.
–When replacing the appliance, always
use a new water supply hose.Water pressure:
at least 0.05 MPa (0.5 bar), maximum 1 MPa (10 bar). At a higher water
pressure: connect pressure-reducing valve ahead.Inlet rate:
minimum 10 litres/minute Water temperature:
cold water; hot water max. temperature 60 °C.
Electrical connection
–Connect the appliance to an
alternating current only, ranging from 220 V to 240 V and 50 Hz or 60 Hz via a correctly installed socket with protective earth conductor. See rating plate for required fusing 1b .
–The socket must be near the appliance
and freely accessible following installation.
If the plug is not freely accessible, an allpole disconnector with a contact opening of at least 3 mm must be fitted on the installation side to satisfy the relevant safety instructions.
–The connection may be modified by
technicians only.
– A power cord extension may be
purchased from customer service only.
–Use only a residual current operated
circuit-breaker which features
the symbol ?. Only this extension guarantees compliance with the currently valid regulations.–The appliance features a water
damage protection system. Please note the system will not function
unless the power supply is connected.
Removing the appliance
Also observe the sequence of worksteps here.
–Disconnect the appliance from the
power supply.
–Turn off the water supply.
–Disconnect the waste water and fresh
water connections.
–Pull out the appliance, carefully pulling
the hose behind.
Transportation
Empty the dishwasher and secure loose parts.
Drain the appliance according to the following steps:–Turn on the tap.–Close the door.
–Switch on ON/OFF switch (.
–Select programme with the highest
temperature.
–Press START button 8.
Programme sequence starts.–After approx. 4 minutes press
the START button 8 until all displays go out.
After approx. 1 min. the appliance is completely drained.
–Switch off ON/OFF switch (.–Turn off the tap, disconnect supply
hose and drain water.
Transport appliance upright only.
(This prevents residual water from running into the machine control and damaging the programme sequence.)
Protection against frost
If the appliance is in a room where there is a risk of frost (e.g. holiday home), empty the appliance completely (see Transportation).
洗碗机分配器使用说明书
洗碗机分配器 分配器的安装 1、机身安装将机身固定在架子或垂直的墙面上，保证机身远离洗碗机的通风口及蒸汽通道上，否则会造成设备过热，从而影响运行状况。机身后壳上的预留孔是用于安装于墙面时上螺丝之用，安装时需加密封垫片。 2、分配器安装 1）探头的安装： 当分配器选择探头控制加料模式时，必须安装探头。探头必须安装在水箱液面以下，并尽可能的在靠近水箱底部的洗碗机缸臂上钻一个22.0MM的孔，用橡胶圈从内、外部固定探头。探头应与热源、洗涤剂入口、排水管、进水管等保持一定距离。 2）洗涤剂注入器的安装 注入器应安装在水箱液面以上，在洗涤缸臂适当位置钻一个22.0MM的孔安装注入器，作为洗涤剂的入口。用橡胶垫圈从内部固定注入器。 3）催干剂单向阀的安装 将单向阀安装在洗碗机的过水管或者加热包上。一般洗碗机上有预留接口；若没有，在管壁厚度足够的情况下，自钻一个11/32（8.7MM）的孔或用三通来替代。 4）输液管连接 将ф6MM的白色输液管插入洗涤泵的黑色蠕动胶管末端，并用拉带扎紧。再将输液管截成适当
长度的两段，长度以达到洗涤剂料桶与重锤注入器连接。进料输液管末端与注入器用白色螺帽紧密连接。 同样，将ф6MM的输液管截成适当长度的两段，长度以达到催干剂料桶与重锤连接。进料输液管一端与催干泵的黑色蠕动胶管末端相连，另一端与白色PVC吸液管用白色螺帽相连，然后一并放入催干剂料桶。出料输液管末端与单向阀相连。 电路安装 1、分配器工作电压（常电源）220V、110V，如果有24V电压则不需要安装变压器电源，电源单独设置电源开关。 2、连接主电源前检查洗碗机输出端电压后再进行连接，以免烧坏变压器以及电路板。 3、一般洗碗机都在电控箱内，留有洗涤剂催干剂的电源信号接口，比较方便的就可以接在分配器的触发信号连接柱上，电压范围在24V—230V都可以。 4、如果洗碗机没有预留洗涤剂催干剂的电源信号，可以将触发电源信号连接在主洗接触器和过水接触器的电源上。 5、分配器选择在时间速度控制模式时，则将首次加药的电源信号，连接进水电磁阀的电源上。 设置与调试 1、具体见电路板图标和屏幕显示及设置。 2、此机有清洁剂泵、催干剂泵手动按钮，在显示面板上，可以在初次使用时将清洁剂、催干剂直接打入泵体内，可以测试泵是否能正常运转，压力如何。 3、在不用探头模式下，（时间模式P0）具有首次加药功能，只需要将进水电磁阀的电源信号接入DET.SIG接线柱，再设置C2、C3，可以设置延时定时功能，也可以设置与电源信号同步调节速度，进行首次加入清洁剂的运行功能。 4、在不用探头的模式下，补充加药量的控制。将信号电源接到RINSE.SIG接线柱，此时可以调节C4、C5，即可与电源信号同步运行（将延时调到0，定时调到0），也可运用速度C1调节加药量。也可以用延时功能和定时功能循环加药，在通道式洗碗机内特别适用。再可以调节b2、b3，与电源信号同步运行（将延时调到0，定时调到0）。用速度调节加催干剂的量（通道式），也可以定时加催干剂的量（门式）。 5、在探头模式下，将A1设置为最高转速。数字越大转速越快，最高为99，A2为浓度设置，数字越大浓度越高，应运用化学滴定法来设置您所需要的清洁剂浓度范围(建议值55)，A3为报警延时时间，最长时间为（99*2）S，如果在设定的时间内，没有将加药浓度达到所设定的范围内，报警器会蜂鸣，蜂鸣时间等于A4所设定的时间，分配器会立即启动时间模式。查找原因后可重新调回探头模式。 6、在探头模式下，催干剂泵的设置可以用速度调节加药量（将延时调到0，定时调到0），也可以用延时时间，定时时间来调节加药量（一般在门式上）。 7、在时间模式时，在信号线始终有电的情况下，如果要求两个泵只运转一次，只需要把B2、C4调为0,B3、C5调为需泵运转的相应时间，其它不管即可。 8、在使用探头模式时，当对数值进行设置后，需要从探头模式退出，所设置的新数值才能生效。 9、注意事项：在使用探头模式时，请务必把时间模式也调节到适量位置。
家用自动洗碗机的工作原理和使用说明
家用自动洗碗机工作原理和使用说明 洗碗这件事，看似不大却又在潜移默化的影响着我们的生活。当你刚和家人朋友吃完饭，谈笑风生的时候，转身看着一摞摞油腻的碗筷堆积在厨房的时候，笑会立刻僵住，内心ｏｓ，“哎，又要洗碗了。。。。。”这可能是我们每个人都会经常遇到的事情，直白点说，洗碗就是件很讨厌的事情。 双手沾上油，手上那种滑滑的有点抓不住的感觉，再加上还有些残渣菜叶沾到手背上，还有七七八八的花椒粒胡椒粉辣椒籽，在油叽叽的手和碗盘之间生硬的硌着。努力的想把油腻的碗抓紧，却不得不接受花椒辣椒颗粒的硬拗，是的，我特别不喜欢这个感觉。而洗干净碗以后，哪怕已经把手清洗干净且抹上护手霜，洗碗液留下的那种涩涩的感觉总是在手上要停留很久，相当不舒服。 总之，这些种种，就能看出我是多么厌恶洗碗这件小事了，能躲多远就躲多远！！！ 有了洗碗机之后，洗碗这件讨厌人的小事就不见啦。 那么洗碗机到底是中怎么工作（原理），以及如何操作？ 【洗碗机的工作原理】 这款洗碗机是depelec中式洗碗机DCS-Q8，通过微电脑控制方式，用双层反向螺旋双峰喷臂，通过高压、高速喷射，形成立体循环水柱，水温可达70度高温，可以快速分解油脂，去除顽固动植物油脂，使细菌失去活力，在清洁剂的辅助作用下，对餐具进行冲洗，达到清洁效果。同时采用三重自清洗过滤系统，过滤细致，可以将污水残渣强力排除，使残渣不会停留在过滤器中，水压稳定、降低噪音，无泡洗碗更干净。高温清洗结束后，餐具表面温度逐渐降低过程中，不断蒸发水分，快速干燥餐具，如同置于暴晒中，让霉菌无所遁形。 【操作说明】 第一步:
按开/关键开启洗碗机,进入待机状态。 第二步: 按程序键，屏幕上的程序图标A组 会依次亮起, 选择适合你的洗涤程序。 第三步: 按下启动/哲停键,屏幕“:”闪烁、,洗涤程序开始。 亮时,进水异常提醒,确保水龙头已经打开。 亮时,表示需要添加亮碟剂,详见说明书添加量亮碟剂部分。 亮时,表示需要添加专用盐,详见说明书添加软水盐部分。 【使用好处】 1、洗涤：全封闭式洗涤，不用抹布，切断细菌传播途径。 2、消毒：采用加热及专门的洗涤用品：涤龙浸泡粉、消毒剂、洗洁精，足以杀死大肠杆菌、葡萄洗碗机球菌、肝炎病毒等病菌病毒。 3、烘干：洗刷后直接烘干，避免水渍留下的斑痕，使餐具更光洁。
洗碗机作业指导书
洗碗机安全操作指导书 一、洗碗机开机前准备： 1．该设备必须专人负责，操作，维修及保养； 2．操作人员需学习洗碗机《使用说明书》，了解该设备的基本结构和性能，熟练掌握操作规程，并严格按照操作规程进行操作； 3．洗碗机用电量大，为防止导线超负荷，须采用单独线路供电，同时安装合适的熔断器和使用耐高温的绝缘材料并加装漏电保护器；4．开机前加满洗缸水，点检机台外壳是否完整有无破损，安全防护罩是否牢固齐全；机械部件传动、润滑是否良好有无异音，各部零件有无松动； 5．点检电气装置是否完好，各按钮是否灵敏，仪表指针是否正常，接地是否正常； 6．检查水箱内是否有异物，各管路是否畅通，加热，喷淋，密封功能是否正常，一切正常方可投入使用； 二、操作程序： 1．严格按照检查标准进行点检； 2．检查完毕后，打开注水阀，注入冷水，水注满后即关闭进阀门；3．开机前40分钟准备预热工作； 4.开启蒸汽总阀门，打开汽门将各水箱的水升温到不低于85℃，然后关闭小汽门继续加热，保证水箱内水的温度不致降低； 5.到电器柜合闸，接通洗碗机电源，启动输送带和水泵开关，空车运转几分钟，并检查机械部件传动平稳，润滑良好、无异音，各部零件
无松动； 6．正常后开始洗碗，打开消毒汽门，运转过程中手不要放在输送带上； 7．在清洗过程中，餐具放置均匀、不重叠并倾斜放在输送带上，小件餐具要放在洗涤筐内。餐具在放进水箱前应先粗洗，对已干了的淀粉等污垢需先浸泡，以减少过滤网以及洗涤喷嘴的堵塞，保证洗涤效果； 8．运转中发现异常现象和不正常的声音要立即停车，及时清除餐具的碎片；如有紧急情况可在尾端侧边按OFF钮,即停止运转; 9．机器运行中，专职人员不得擅离职守，一定要做到人离停机；三、操作完毕后： 1．断开洗碗机电源总开关； 2．打开清扫阀门，用刷子或抹布清理洗碗机的出入口，把污物冲入滤网； 3．打开排水阀，排掉各水箱的水。用水管冲洗洗碗机内部； 4．取出滤网，清理污物，待水排尽后方可取出吸入滤网，吸入滤网必须每次取出清理； 5．将取出滤网放回原处，开启窗门使洗碗机内部干燥； 阜阳市棋胜后勤管理服务有限公司
洗碗机操作指导书
1.0目的 指导测试人员正确操作测试仪器，确保仪器正常运作及实验效果的准确，同时提高使用仪器的工作效率和寿命。 2.0使用范围：本公司品质部检测人员。 3.0操作步骤： 3.1打开总电源及水阀开关（显示“ON”为打开，显示“OFF”为关闭） 3.2按下Power键，Power键指示灯亮为仪器打开，不亮为关闭。 3.3按下Mode键，调整供应水资源Water Supply一栏的时间参数值，分别为35sec、55sec、75sec，调至相应指示灯 处，即为所选时间。 3.4待仪器自己升温，当温度（TEMPERARURE）区显示值为80-90摄氏度，方可进行实验。 3.5按下Work键，Washing键指示灯亮，仪器正常工作，此时时间（TIME sec）一栏数值在变化，仪器洗槽开始喷水， 对产品进行洗涤；水温过低时，仪器自动加热清洗水，此时Rinsing和Heating键亮。 3.6当（Time sec）栏时间显示到到所设定的供水时间时，对产品清洗结束，Rinsing键灯亮，TIME sec兰进入倒计时， 对产品进行15s的淋浴、冲洗。 3.7当冲洗完毕，仪器出现提示音（嘀嘀声），此时完成一个冲洗循环，当连续响三次后按下Work键，进行下一轮清 洗，重复步骤3.5、3.6循环作业。 3.8每做完10个循环，取出实验产品检测，主要检查产品是否有掉漆、掉叻架油、变色，并做好测试记录。待做完 300个循环，取出产品，关掉电源及水阀，并将测试结果填写于《试验报告》中。 4.0判定标准 冲洗200个循环以下掉漆或掉叻架、变色、将判定为严重缺陷，200至此299个循环判定为轻微缺陷。 5.0注意事项： 5.1操作人员应遵守操作流程，首先查看两种洗碗剂溶液是否够量、有无过期。 5.2查看进、出水管以及洗碗剂溶液连接管是否与仪器紧密连接。 5.3仪器在运转过程中，查看进、出水量以及时间运行等有无异常；若发现仪器运转出现异常，应及时关掉电源，通 知仪器管理员，采取相应措施。 5.4操作人员应在指定位置安全操作，以免烫伤。 6.0维护及保养： 仪器表面点触式操作界面、洗槽及喷水管表面应保持清洁。 品质政策：专精务实，开拓创新，以人为本，服务客户
洗碗机分配器使用说明书
洗碗机分配器使用说明书 一、简价 洗碗机分配器，适用于国外销售的任何品牌洗碗机。是一种准确方便经济实用的洗碗机清洁剂、催干剂分配器，有门式、通道式专用型，有探头和时间速度双模式控制方法，有CPU控制的探头、非探头（时间、速度）双模式控制，适用于任何类型洗碗机上使用。 二、安装 1、分配器安装 在洗碗机的进口上方墙体，打两个φ6塑胶膨胀管螺丝固定分配器，须将密封垫片安在墙头，防蒸发进入箱体内。 2、管路安装 1）将φ6塑管截成适当长度，插入泵管两端用扎带扎紧，注意不要将吸入口、出口搞反。泵的转向应是顺时针方向，吸入口的塑管末端装上过滤底阀， 长度能放入清洁剂和催干剂的桶内，出口与清洁剂下药口和单向阀连接。 2）清苦剂进口，在洗碗机洗涤槽水平面上方，打一个φ10.2-10.5孔或7/8” 标准孔装上进药口装置. 3）催干剂进口须单向阀,一般洗碗机上有预留口。 3、探头安装 必须安装在洗涤槽的水平面下10CM左右的地方，最好的位置应离水泵吸口 较近，离进水口较远，切忌安装在加热管附近，否则容易熔化，选择好位置 后打一个22（7/8英寸）的孔，用0.75-1平方米多股软线,连接至分配器的探 头信号连接柱上. 4、电路安装 1）分配器工作电压（常电源）220V、110V，如有24V电压则不必接变压器电源，电源单独设置电源开关（以备清洗洗碗机用）。 2）连接主电源前检查洗碗机输出端电压再进行连接，以免烧坏变压器及电路板，确实后再连接。 3）一般洗碗机都在电控箱内，留有洗涤剂催干剂的电源信号接口，比较方便的就可接在分配器的触发信号连接柱上，电压范围在14V-230V都可以。 4）若洗碗机没有预留洗涤干剂的电源信号，可以将触发电源信号连接在主洗接触器和过水接触器的电源上。 5）分配器选择在时间速度控制模式时，则将首次加药的电源信号，连接进水电磁阀的电源上。 6）远程预警，可用连接线将分配器内ALARM 连接柱连接外部报警器（3V-24V）。 5、设置与调试 1）具体见电路板图示和屏幕显示及设置。 2）此机有清洁剂泵、催干剂泵手动按钮，在显示面板上，可在初次使用时将清洁剂、催干剂直接打入泵体内，可测试泵是否能正常运转，压力如何。
ge洗碗机说明书
ge洗碗机说明书 篇一：洗碗机说明书节能洗碗机说明书 洗碗机说明书大家肯定都有过这样的经历:油腻腻的碗筷,冬天冰冷的洗碗水…看着就难过发愁!真是不想洗，但是总让老婆或者爸妈洗也心疼啊！可是市场上的洗碗机不说价格多贵，动不动就上万元，而且体积也大，不是新装修的房子都没办法嵌在橱柜里，而且洗一次要一个多小时，时间太久！最关键的是洗不干净，不说洗杯子了，连碗底都洗不干净！还费电费水容易坏。。由于自己也深受其害，经常为洗碗郁闷不已，所以和很多朋友大量查找国内外的洗碗机，终于找到也最适合中国习惯的洗碗机，既可洗碗，又能洗碟、洗盘、洗餐盒、洗杯、还能给宝宝洗奶瓶！还有干净快速，节能环保，方便移动，寿命超长等特点，家用商用都适合，价格大家都想象不到的低，多少？才一百多！ 这么好的产品都动心了吧？！那咱们赶紧来详细了解一下吧洗碗机性能、产品参数、安装方法、使用方法、用后清洁等大家关心的问题吧。 节能洗碗机-新时代的宠儿 多功能节能环保洗碗机属国内首创，不需要接电源，真正实现零电耗，创造性地诠释了最具清洁功能的刷洗功能，适用于各种大小，各种材质的碗、碟、餐盒、餐盘、杯子、奶瓶、刀叉、筷子等的清洗！外形采用国际流行的流线型设
计，设计新颖，操作简单，方便实用！独特的洗碗双毛刷配合设计和洗杯毛刷设计可异常干净地清除各种死角，彻底解决一般洗碗机洗不到碗底杯底的烦恼！还具有去污能力强，占地小，价格实惠，快捷，方便，省水，省电，安全可靠，经久耐用，能洗各种形状碗、碟、盘、杯、奶瓶等，不需培训即可操作等优点。 晟宇伟业公司节能洗碗机速度极快，熟练的话可达到600~1000个/小时，不仅适用于家用，也适合商用！而且拥有最好的性价比，每台都经过严格的测试和检验，设备的各项性能均达到或超过国内外同类产品水平，产品远销到美国，德国，日这，澳大利亚，英国，加拿大，奥地利，匈牙利等十几个国家，获得一致好评！ 比于昂贵的，体积庞大，又耗电又耗水，时间长，餐具易破，容易损坏，不易维修，需要专业培训的大型洗碗机来说，这款洗碗机能完美解决上述大型洗碗机易出现的烦心问题。 产品参数 主体材质：优质PP； 毛刷才智：优质弹性PET； 尺寸（长宽高）：41*24*23厘米； 重量：2.3kg； 电压：0V；
洗碗机-操作流程
工作行为规范系列洗碗机:操作流程（标准、完整、实用、可修改）
编号：FS-QG-31091 洗碗机:操作流程 Dishwasher: operating procedure 说明：为规范化、制度化和统一化作业行为，使人员管理工作有章可循，提高工作效率和责任感、归属感，特此编写。 洗碗机操作流程准备程序:1、先将洗碗机的电源闸门合上，确保洗碗机电源已接通。2、将网板和垃圾篮放在清洗水箱上的适当位置，插好排水管。3、关上机门。4、按一下启动按钮，计算机控制器开启，并自动进行注水。(注意，请勿擅自调节洗碗机设置按钮，日常操作仅需要操作面板上第一个和最后一个开关键)5、注水停止后打开机门，检查水箱是否已加满水。注水前先关闭清洁剂自动分配器电源，当注水程序结束后再将清洁剂自动分配器电源打开。6、关上机门后，清洗和喷淋周期会自动开始。7、请等水箱升到适当的温度后再开始洗涤工作。清洗碗碟:1、请先清除碗盘上较大的食物残屑。2、根据碗盘的大小情况选择合适的洗碗机框。3、将盘插立在框架上。请注意不要将盘迭在一起，因为水必须要能冲洗到盘的正反两面才行。请将盘放在有立架的框架中，
靠边立起。茶杯、玻璃杯和碗则倒放在开放式篮框或格层式篮框里。刀叉以及其它小餐具可以疏松地放在开放式篮框的底部。4、篮框装满后，将门打开，将篮框推入洗碗机内，然后关上门。清洗和喷淋周期会自动开始。清洗周期是在关门以后开始，喷淋周期则是在清洗周期结束开始。5、清洗和喷淋周期结束后，将门打开，拉出篮框后，在等待30秒后才能将篮框中干净的碗盘取出并叠放整齐，这样可以使刚洗好的碗盘等将水自动沥干。然后继续装入下一批需要清洗的碗盘，将篮框推入洗碗机内，然后关上门。6、如果您想在清洗周期开始后加装碗盘，请先关掉电源开关，等十秒钟后再开门，让洗臂慢慢停下，避免热水溅出，烫伤操作人员。(请尽量不要使用此操作)清洗机器:每次操作完机器后都彻底清洁一次(用餐使用后)，或至少每天一次。清洁步骤如下:1、按下洗碗机关闭按钮后，并切断电源2、打开门3、清洗不锈钢工作台并让水流回洗碗机。4、拔出排水管排水5、拆下网板，垃圾篮和泵吸入滤网，将里面的杂物倒出后彻底清洁干净。 6、将洗碗机内部彻底清洁并冲洗干净。 7、将泵吸入滤网和网板、垃圾篮装回。 8、敞开门以使空气自然吹干机器内部。
洗碗机分配器使用说明书
洗碗机分配器 数字型电脑液体分配器 分配器的安装 1、 机身安装 将机身固定在架子或垂直的墙面上， 保证机身远离洗碗机的通风口及蒸汽通道上, 否则 会造成设备过热，从而影响运行状况。机身后壳上的预留孔是用于安装于墙面时上螺丝之 用，安装时需加密封垫片。 2、 分配器安装 1） 探头的安装： 当分配器选择探头控制加料模式时，必须安装探头。探头必须安装在水箱液面以下，并尽可能 的在靠近水箱底部的洗碗机缸臂上钻一个的孔，用橡胶圈从内、外部固定探头。探头应与热源、 洗涤剂入口、排水管、进水管等保持一定距离。 2） 洗涤剂注入器的安装 注入器应安装在水箱液面以上，在洗涤缸臂适当位置钻一个的孔安装注入器，作为洗涤剂的入 口。用橡胶垫圈从内部固定注入器。 3） 催干剂单向阀的安装 将单向阀安装在洗碗机的过水管或者加热包上。一般洗碗机上有预留接口；若没有，在管壁厚 度足够的情况下，自钻一个 11/32 （）的孔或用三通来替代。 4） 输液管连接 将血6MM 的白色输液管插入洗涤泵的黑色蠕动胶管末端，并用拉带扎紧。再将输液管截成适当 长度的两段，长度以达到洗涤剂料桶与重锤注入器连接。进料输液管末端与注入器用白色螺帽 紧密连接。 cjiiEMaNOlOH 白冷 FACE I LA, b ZT3O6 酹iff 冒 PIPETTES FJ4(J-
2017年洗碗机系统使用说明书(word版本)
洗碗机系统 使 用 说 明 书
目录 一．养成安全第一的好习惯 二．控制板视图 三．洗碗机内部视图 四．技术参数 五．盐、洗涤剂和助清剂 六．将餐具装入洗碗机 七．运行洗碗机 八．洗涤循环调整按钮 九．洗涤循环表 十．节能密诀 十一．如何保存洗碗机 十二．清洗及专门维护 十三．故障排除 十四．安装
一．养成安全第一的好习惯 注意: 请仔细阅读本手册的安项内容, 它向你提供了有关洗碗机安全、正确安装以及使用和维护的重要内容。 该洗碗机符合ＥＥＣ下列标准： －７３／２３ＥＥＣ１９／０２／７３（低压）规定以及其后的修定本； －８９／３３６／ＥＥＣ０３／０５／８９（电磁兼容性）标准以及其后的修定本。 １．小心处置包装材料。 ２．除去包装后，请检查确认机器是否有损，如有疑惑，请与Ariston 授权的技术人员联系。 ３．该洗碗机仅供成年人用于洗涤家用碗碟和烹饪用具。 ４．使用洗碗机时，请遵守以下基本规则： ――光脚或手脚潮湿时，严禁触摸洗碗机； ――严禁使用接线板和多孔插座； ――安装时，禁止将电源线过度拉拽或弯曲； ――如果机器不能正常运转或有必要维修，切断电源。 ５．将洗涤剂存放在小孩接触不到的地方，机器工作时，让小孩远离洗碗机。６．洗碗机不能安装在室外，即使有顶蓬的地方也不行，将其暴露在雨中或外界环境下是十分危险的。 ７．洗涤过程中或洗完之后，不要触摸发热元件。 ８．机门打开时，禁止斜靠或坐在门上，因为这样可使机器翻倒。 ９．如果机器不能正常工作，关掉进水，切断电源（拨下电源插头）。如果您自已不能解决问题，请与维修中心联系。 １０．只有被授权的技术人员方可进行维修。 １１．不再使用机器时，通过切断电源线和拆下门锁，使机器不能运行。 二．控制板视图
STR洗碗机操作说明书
输送式洗碗机STR 操作说明
目录 1 关于说明书 ------------------------------------------------------------------3 1.1 使用符号说明---------------------------------------------------------------3 2 产品说明---------------------------------------------------------------------3 3 安全事项---------------------------------------------------------------------3 3.1 指定用途-------------------------------------------------------------------3 3.2 非指定用途-----------------------------------------------------------------3 3.3 化学物质（清洁剂，漂洗助剂，除垢剂等）的处理------------------------------- 4 3.4 通用安全事项---------------------------------------------------------------4 3.5 日常清洁和维护-------------------------------------------------------------4 4 机器工作前-------------------------------------------------------------------4 4.1 检查机器的完整性-----------------------------------------------------------5 4.2 首次安装-------------------------------------------------------------------5 5 操作和控制原理---------------------------------------------------------------5 6 操作-------------------------------------------------------------------------5 6.1 操作前准备-----------------------------------------------------------------5 6.1.1 机器开启前---------------------------------------------------------------5 6.1.2 开启机器-----------------------------------------------------------------6 6.2 洗涤-----------------------------------------------------------------------6 6.2.1 启动/停止传送------------------------------------------------------------6 6.2.2 洗涤--------------------------------------------------------------------- 7 6.2.3 打开机器门---------------------------------------------------------------7 6.2.4 操作暂停-----------------------------------------------------------------7 6.3 用较低的漂洗温度洗涤（特殊机型）-------------------------------------------7 6.4 温度显示在控制主板上------------------------------------------------------- 8 6.5 工作台限位开关-------------------------------------------------------------8 6.6 日常检查-------------------------------------------------------------------8 6.7 关闭机器-------------------------------------------------------------------9 7 维护和保养-------------------------------------------------------------------9 7.1 日检查---------------------------------------------------------------------9 7.1.1 排水槽（启动排水程序）---------------------------------------------------9 7.1.2 清洗机器外壁------------------------------------------------------------10 7.1.3 检查外部水处理----------------------------------------------------------10 7.2 月检查--------------------------------------------------------------------11 7.2.1 清洗脏凹槽--------------------------------------------------------------11 7.2.2 除锈--------------------------------------------------------------------11 7.3 客服保养------------------------------------------------------------------11 8 机器长期停用----------------------------------------------------------------12 9 故障------------------------------------------------------------------------12 9.1 故障；显示在主板上--------------------------------------------------------12 9.2 故障----------------------------------------------------------------------13 10 技术参数-------------------------------------------------------------------14 10.1 技术参数-----------------------------------------------------------------14 10.2 标准---------------------------------------------------------------------14
洗碗机说明书
洗碗机说明书
目录 1.安装说明书............. ...... ...... ...... . (1) 2.机器操作说明............ ...... ...... ...... (2) 3.控制面板按钮功能说明...... ....... ...... ...... (3) 4.维护说明...... ...... ...... ...... ...... ...... (4) 5.故障排除说明...... ...... ...... ...... ...... .. (5) 6.机器电路图...... ...... ...... ...... ...... ...... (6)
宏阳洗碗机安装说明书 一安装洗碗机 1.在洗碗机放好位置后，调节水平脚螺丝，使机器处于水平状态 连接好供给水管接，连接好进口出口工作台。 2.安装好分配器，确保分配器的两根塑料输入管进口分别完全淹 没在药水桶里，两根输出管与机器连接好 3.使用60A三相四线漏电保护器，电缆线采用国标16平方铜质 3+1电缆线，认真接好三根火线与零线，确保好地线有地良好 连接。 二机器操作说明 1.打开漏电保护器 2.打开机器控制箱正面的急停按钮，对应的电源指示灯变亮。然 后按绿色开机按钮，绿色加水指示灯变亮，机器开始加水。 3.当绿色加水指示灯熄灭，时表示机器加水完成，同时加热指示 灯会变亮，机器开始加热。此时机器已经进入准备洗涤状态。 4.按洗涤按钮，水泵开始工作，喷淋管内高压水开始喷淋，同时 传送电机开始运转，传送动作开始。注意：如果喷淋管内有少 许水喷出，说明水泵电机翻转，此时更换任意两根火线即可。 5.一切正常则机器安装成功，试运行成功，便可投入工作。
洗碗机说明
目录 ?? 洗碗机维修入门指南 ?? 洗碗机机门和开关的维修 ?? 洗碗机阀门、喷洒器和碗架的维修 ?? 与电机和水相关的洗碗机维修问题 洗碗机维修入门指南编辑本段回目录 最新型的洗碗机的控制面板有点吓人。您或许觉得它上面装着如此多的刻度表、按钮和其他部件，看上去就已经够复杂的了，莫说修理了。但实际并非如此。除控制面板外，在过去2 0年中，洗碗机的基本设计没有发生太大的变化。对于大多数的洗碗机故障，您都可以自己维修。在本文中我们将讲述一些自行维修和保养的方法。 洗碗机的部件可以单独更换，这样做其实比请专业维修人员修理还要简单便宜。如果您不能确定某个部件是否还能使用，可以把它从洗碗机上拆下来，拿到专业人员那里进行测试。之后您可以根据预计的修理费用决定是买一个新部件，还是修理坏部件。 在美国，洗碗机通常使用115伏或120伏的电压。使用的水直接来自热水器，废水则通过水槽的排水管排出。洗碗机不与冷水供应系统相连。为了达到最好的洗涤效果，您应当把热水器水温设置为不低于摄氏60度。水温低于这个温度时通常洗不干净碗碟，除非您的洗碗机是新型洗碗机，可以预热进水。洗碗机的控水开关一般位于与它相连的水槽的下方。 警告：因为洗碗机分别与供水系统和电力系统相连，所以您在这种电器上进行操作时必须同时考虑这两个系统。在对洗碗机的部件做任何修理之前，都应确保该部件没有连接电源，或关闭与它相连的电源，并拔掉主面板或分面板上的控制电路的保险丝或断电器。关闭位于地下室或者厨房下面的管路阀门，切断对洗碗机的供水。 基本操作检查 如果洗碗机无法使用，您可以进行如下的操作进行检查： 步骤1：检查并确保供电。如果它有插头插在墙上的电源插座上，那么检查电线、插头和插座，确保它们正常工作。同时还要检查控制插座的开关，确保它是闭合的。绝大多数嵌入式洗碗机都与线路直接相连。检查主控面板上保险丝是否烧断了，断电器是否断开了，然后恢复电路。如果您家里用的是老式的洗碗机，那它可能与分控制面板相连。检查这个面板上的保险丝或断电器，然后恢复电路。 步骤2：如果线路已通电，且墙上的插座是由开关控制的，则开关有可能坏了。使用电压测试仪测试开关。取下开关盖，将测试仪的一支探针置于一端，另一支探针置于另一端。如果检测灯亮，开关就是好的；如果没亮，则是坏的，这时需要更换一个相同型号的新开关。
洗碗机说明书节能洗碗机说明书
洗碗机说明书 大家肯定都有过这样的经历:油腻腻的碗筷,冬天冰冷的洗碗水…看着就难过发愁!真是不想洗，但是总让老婆或者爸妈洗也心疼啊！ 可是市场上的洗碗机不说价格多贵，动不动就上万元，而且体积也大，不是新装修的房子都没办法嵌在橱柜里，而且洗一次要一个多小时，时间太久！最关键的是洗不干净，不说洗杯子了，连碗底都洗不干净！还费电费水容易坏。。。 由于自己也深受其害，经常为洗碗郁闷不已，所以和很多朋友大量查找国内外的洗碗机，终于找到也最适合中国习惯的洗碗机，既可洗碗，又能洗碟、洗盘、洗餐盒、洗杯、还能给宝宝洗奶瓶！还有干净快速，节能环保，方便移动，寿命超长等特点，家用商用都适合，价格大家都想象不到的低，多少？才一百多！ 这么好的产品都动心了吧？！那咱们赶紧来详细了解一下吧洗碗机性能、产品参数、安装方法、使用方法、用后清洁等大家关心的问题吧。
节能洗碗机-新时代的宠儿 多功能节能环保洗碗机属国内首创，不需要接电源，真正实现零电耗，创造性地诠释了最具清洁功能的刷洗功能，适用于各种大小，各种材质的碗、碟、餐盒、餐盘、杯子、奶瓶、刀叉、筷子等的清洗！外形采用国际流行的流线型设计，设计新颖，操作简单，方便实用！独特的洗碗双毛刷配合设计和洗杯毛刷设计可异常干净地清除各种死角，彻底解决一般洗碗机洗不到碗底杯底的烦恼！还具有去污能力强，占地小，价格实惠，快捷，方便，省水，省电，安全可靠，经久耐用，能洗各种形状碗、碟、盘、杯、奶瓶等，不需培训即可操作等优点。 晟宇伟业公司节能洗碗机速度极快，熟练的话可达到600~1000个/小时，不仅适用于家用，也适合商用！而且拥有最好的性价比，每台都经过严格的测试和检验，设备的各项性能均达到或超过国内外同类产品水平，产品远销到美国，德国，日这，澳大利亚，英国，加拿大，奥地 利，匈牙利等十几个国家，获得一致好评！
洗碗机操作规范
洗碗机安全操作规范 一、开机规范 1.检查隔渣盘（也叫过滤网），支架等是否放回原位，排水管插好，机器关闭 严密。 2.检查清洁剂、催干剂,保持桶内有足够的药剂。 3.在使用洗碗机之前30分钟，开启电源开关，洗碗机自动上水、加热。 4.主洗缸温度达60度，漂洗温度达82度即可以开始使用。 二、洗涤餐具 1.将餐具去除残渣后，放入放有洗涤灵的水槽中用温水浸泡2-3分钟然后进行预洗。 洗涤茶杯、咖啡杯、密胺餐具等须用专门的去渍剂溶液浸泡去渍。 2.分类装筐，最好将同类餐具放在一起，不能将餐具重叠。 3.用花洒冲洗，尽量冲掉餐具上残留的洗涤灵。 4.打开揭盖式洗碗机门，推进装好餐具的洗涤筐，关闭机门,洗碗机自动开始洗涤。通道式洗碗机，推进洗涤筐自动清洗。 5.洗涤结束从洗碗机中出来的餐具晾半分钟后，待水分蒸发。 6.检查挑出个别未洗净的餐具，重新浸泡返洗。 三、清洗洗碗机（每餐工作结束后） 1.关闭洗碗机电源（指示灯灭）。 2.取出隔渣盘，去除残渣，并清洗干净。 3.检查喷嘴，如有堵塞须清洗干净。 4.拔起排水阀排水，并将机器内部清洗干净。 5.关闭排水水阀，放回隔渣盘，注意打开机门晾干。 6.将机器外部、工作台清洗干净，待下次使用。 四、洗碗机维护（洗碗机每周除垢一次，防止加热管被烧坏） 1.关闭分配器电源开关，放掉洗碗机水箱中原来的水，重新放入干净的水。2．往洗碗机中倒入一小桶除垢剂。 3.启动洗碗机当主洗温度达到50°C到60°C时空清洗30分钟（注意不能洗餐具），待机器内水垢已基本除掉。 4.关闭洗碗机电源，拔起排水管，将含有除垢剂的水排放完。 5.用花洒冲洗碗机内壁。 6.打开分配器开关，以后可以正常使用。 五、注意事项 1.洗碗机工作中发出异常声响应立即停机检查，排除故障后再使用。 2.洗碗机专用洗涤剂，不能接触皮肤，如不慎接触皮肤，应立即用清水冲掉。
揭盖式洗碗机使用说明书模板
揭盖式洗碗机使用 说明书
XYXWZ1型 揭盖式洗碗机使用说明书 目录 结构与安装操作简要介绍 1.型号与名称 (1) 2.用途与特点 (1) 3.技术参数 (2) 4.主要结构及工作原理 (2) 5.安装与调整 (2) 6.操作面板 (3) 7.机器操作 (3) 8.机器清洗 (4) 9.洗涤物品的摆放 (4) 操作使用说明 1.总则 (5) 2.安全注意事项 (5) 3.安装指南 (6) 4.机器运行 (8) 5.洗涤及漂洗准备 (8) 6.洗涤及漂洗操作 (10) 7.关机 (11) 8.操作面板说明 (12)
9.维护与保养 (13) 10.简易故障诊断 (13) 附图：平面总图、电路图
XYXWZ1型揭盖式洗碗机 结构与安装操作简要介绍 注意： 本机必须由受过专业培训的合格技术人员安装，由受过专业培训的合格操作人员操作。安装及操作前请详细阅读本说明书。 1.型号与名称 型号：XYXWZ1 名称：揭盖式洗碗碟机 2.用途与特点 本机采用了当前最流行的旋转式洗涤臂和漂洗臂的设计，确保了一流的洗涤效果。电器上采用了电脑芯片程序控制系统和新颖的操作面板获得最舒适的操作过程，能够满足各类盘、碟、碗以及玻璃杯的高标准洗涤要求。特别适用于宾馆、饭店、餐厅和食堂等卫生洗涤餐具的场所。本产品还具有以下特点： 2.1不锈钢结构的双层上揭盖盖，前置式操作杆，操作舒适并节约能 源。后敞开式的揭盖壳，打开机揭盖使蒸汽从后面溢出，从而增强了操作的舒适度。420mm的净通高度，洗涤大碗碟更为方便。 2.2圆弧角过渡的不锈钢洗涤水槽美观，无腐蚀，易操作，易清洗。 本机具有自清洗功能，清洗极为方便，最大程度保持机器的清洁与卫生。本机结构简洁、牢固，机器性能可靠，易维修，寿命
洗碗机安全操作规程通用版
操作规程编号：YTO-FS-PD338 洗碗机安全操作规程通用版 In Order T o Standardize The Management Of Daily Behavior, The Activities And T asks Are Controlled By The Determined Terms, So As T o Achieve The Effect Of Safe Production And Reduce Hidden Dangers. 标准/ 权威/ 规范/ 实用 Authoritative And Practical Standards
洗碗机安全操作规程通用版 使用提示：本操作规程文件可用于工作中为规范日常行为与作业运行过程的管理，通过对确定的条款对活动和任务实施控制,使活动和任务在受控状态，从而达到安全生产和减少隐患的效果。文件下载后可定制修改，请根据实际需要进行调整和使用。 一、洗碗机开机前准备： 1．该设备必须专人负责，操作，维修及保养； 2．操作人员需进行安全培训，获得上岗证必须持证上岗，并学习洗碗机《使用说明书》，了解该设备的基本结构和性能，熟练掌握操作规程，并严格按照操作规程进行操作； 3．洗碗机用电量大，为防止导线超负荷，须采用单独线路供电，同时安装合适的熔断器和使用耐高温的绝缘材料并加装漏电保护器； 4．开机前加满洗缸水，点检机台外壳是否完整有无破损，安全防护罩是否牢固齐全；机械部件传动、润滑是否良好有无异音，各部零件有无松动； 5．点检电气装置是否完好，各按钮是否灵敏，仪表指针是否正常，接地是否正常； 6．检查水箱内是否有异物，各管路是否畅通，加热，喷淋，密封功能是否正常，一切正常方可投入使用； 二、操作程序：
洗碗机正确的使用方法
见了就想带回家，你知道洗碗机怎么用吗？ 对于洗碗机，相信很多人已不陌生。作为一种能够代替人工洗碗的机器，它正为现代年轻人所簇拥，成为高品质生活方式的象征。但毕竟目前国内洗碗机的普及率还不是很高，大多数人还是觉得它略微“神秘”。很多消费者尚不明晰洗碗机怎么用，东西一到手，却不知道如何下手。 洗碗机可不像洗衣机一样，把要洗的衣服丢进去、加点洗衣液、设好程序就完事儿，还需要考虑餐具的摆放、洗碗的强度和时长，以及使用时的一些注意事项等等。因此，消费者要弄清洗碗机怎么用，就要在购买洗碗机之后熟读产品使用说明书，了解洗碗机的各个组件及基本的使用方法，才能更有效地使用和保养洗碗机，以防操作失误带来不便和对机器造成损坏。以下针对洗碗机的日常使用方法与注意事项进行了详细的解读，供大家参考。 洗碗机怎么用？安装是头等大事 洗碗机送货上门之后，首要任务当然是让它“就位”。市面上大部分洗碗机品牌都有提供免费上门安装服务，即便是通过网络途径购得，也可以联系厂家安排售后人员择日上门进行安装，消费者只需提供合适的安装位置即可。 当然，洗碗机怎么装，还得取决于你所购买的洗碗机类型，不同的洗碗机类型有不同的安装方法。市面上的洗碗机主要有台式、独立柜式、嵌入式和水槽式四种，台式洗碗机和独立柜式洗碗机需要厨房有富余的空间位置，并可能需要对水电线路进行改造；嵌入式洗碗机的安装除了需要水电改造之外，它还对厨房的橱柜尺寸有要求，消费者需要提前测量好橱柜，必要时进行适当的改造；相对其他类型的洗碗机，水槽洗碗机的安装则要简易得多，它直接替换原有水槽位置即可，不仅省空间，更无需改水电线路和橱柜。 （方太水槽洗碗机安装示意图）
洗碗机操作流程
洗碗机操作流程 准备程序： 1、先将洗碗机的电源闸门合上，确保洗碗机电源已接通。 2、将网板和垃圾篮放在清洗水箱上的适当位置，插好排水管。 3、关上机门。 4、按一下启动按钮，计算机控制器开启，并自动进行注水。（注意，请勿擅自调节洗碗机设置按钮，日常操作仅需要操作面板上第一个和最后一个开关键） 5、注水停止后打开机门，检查水箱是否已加满水。注水前先关闭清洁剂自动分配器电源，当注水程序结束后再将清洁剂自动分配器电源打开。 6、关上机门后，清洗和喷淋周期会自动开始。 7、请等水箱升到适当的温度后再开始洗涤工作。 清洗碗碟： 1、请先清除碗盘上较大的食物残屑。 2、根据碗盘的大小情况选择合适的洗碗机框。 3、将盘插立在框架上。请注意不要将盘迭在一起，因为水必须要能冲洗到盘的正反两面才行。请将盘放在有立架的框架中，靠边立起。茶杯、玻璃杯和碗则倒放在开放式篮框或格层式篮框里。刀叉以及其它小餐具可以疏松地放在开放式篮框的底部。 4、篮框装满后，将门打开，将篮框推入洗碗机内，然后关上门。清洗和喷淋周期会自动开始。清洗周期是在关门以后开始，喷淋周期则是在清
洗周期结束开始。 5、清洗和喷淋周期结束后，将门打开，拉出篮框后，在等待30秒后才能将篮框中干净的碗盘取出并叠放整齐，这样可以使刚洗好的碗盘等将水自动沥干。然后继续装入下一批需要清洗的碗盘，将篮框推入洗碗机内，然后关上门。 6、如果您想在清洗周期开始后加装碗盘，请先关掉电源开关，等十秒钟后再开门，让洗臂慢慢停下，避免热水溅出，烫伤操作人员。（请尽量不要使用此操作） 清洗机器： 每次操作完机器后都彻底清洁一次（用餐使用后），或至少每天一次。 清洁步骤如下： 1、按下洗碗机关闭按钮后，并切断电源 2、打开门 3、拔出排水管排水 4、拆下网板，垃圾篮和泵吸入滤网，将里面的杂物倒出后彻底清洁干净。 5、将洗碗机内部彻底清洁并冲洗干净。 6、将泵吸入滤网和网板、垃圾篮装回。 7、敞开门以使空气自然吹干机器内部。 8、检查确定清洗臂和喷淋臂能自由转动，无任何阻碍。 9、检查喷淋臂末端出水口，以确定无水垢和其它异物堵塞。 清洗臂及喷淋臂：