机械术语英文翻译
机械术语英文翻译
阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load
凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key
变形deformation摆杆oscillating bar 摆动从动件oscillating follower
摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism
摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile
摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact
保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone
背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity
闭式链closed kinematic chain闭链机构closed chain mechanism
臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient
标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor
表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness
并联式组合combination in parallel并联机构parallel mechanism
并联组合机构parallel combined mechanism并行工程concurrent engineering
并行设计concurred design, CD不平衡相位phase angle of unbalance
不平衡imbalance (or unbalance)不平衡量amount of unbalance
不完全齿轮机构intermittent gearing波发生器wave generator
波数number of waves补偿compensation
参数化设计parameterization design, PD残余应力residual stress
操纵及控制装置operation control device槽轮Geneva wheel
槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate
槽凸轮groove cam侧隙backlash
差动轮系differential gear train差动螺旋机构differential screw mechanism
差速器differential常用机构conventional mechanism; mechanism in common use
车床lathe承载量系数bearing capacity factor
承载能力bearing capacity成对安装paired mounting
尺寸系列dimension series齿槽tooth space
齿槽宽spacewidth齿侧间隙backlash
齿顶高addendum齿顶圆addendum circle
齿根高dedendum齿根圆dedendum circle
齿厚tooth thickness齿距circular pitch
齿宽face width齿廓tooth profile
齿廓曲线tooth curve齿轮gear
齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack
齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter
齿轮机构gear齿轮轮坯blank
齿轮传动系pinion unit齿轮联轴器gear coupling
齿条传动rack gear齿数tooth number
齿数比gear ratio齿条rack
齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain
齿形系数form factor齿式棘轮机构tooth ratchet mechanism
插齿机gear shaper重合点coincident points
重合度contact ratio冲床punch
传动比transmission ratio, speed ratio传动装置gearing; transmission gear
传动系统driven system传动角transmission angle
传动轴transmission shaft串联式组合combination in series
串联式组合机构series combined mechanism串级调速cascade speed control
创新innovation ; creation创新设计creation design
垂直载荷、法向载荷normal load唇形橡胶密封lip rubber seal磁流体轴承magnetic fluid bearing
从动带轮driven pulley从动件driven link, follower从动件平底宽度width of flat-face
从动件停歇follower dwell从动件运动规律follower motion
从动轮driven gear粗线bold line粗牙螺纹coarse thread
大齿轮gear wheel打包机packer打滑slipping带传动belt driving
带轮belt pulley带式制动器band brake单列轴承single row bearing
单向推力轴承single-direction thrust bearing单万向联轴节single universal joint
单位矢量unit vector当量齿轮equivalent spur gear; virtual gear
当量齿数equivalent teeth number; virtual number of teeth当量摩擦系数equivalent coefficient of friction 当量载荷equivalent load刀具cutter导数derivative倒角chamfer导热性conduction of heat
导程lead导程角lead angle
等加等减速运动规律parabolic motion; constant acceleration and deceleration motion
等速运动规律uniform motion; constant velocity motion
等径凸轮conjugate yoke radial cam等宽凸轮constant-breadth cam
等效构件equivalent link等效力equivalent force等效力矩equivalent moment of force
等效量equivalent等效质量equivalent mass等效转动惯量equivalent moment of inertia
等效动力学模型dynamically equivalent model
底座chassis低副lower pair点划线chain dotted line（疲劳）点蚀pitting垫圈gasket
垫片密封gasket seal碟形弹簧belleville spring顶隙bottom clearance
定轴轮系ordinary gear train; gear train with fixed axes
动力学dynamics动密封kinematical seal动能dynamic energy动力粘度dynamic viscosity
动力润滑dynamic lubrication动平衡dynamic balance
动平衡机dynamic balancing machine动态特性dynamic characteristics
动态分析设计dynamic analysis design动压力dynamic reaction动载荷dynamic load
端面transverse plane端面参数transverse parameters端面齿距transverse circular pitch
端面齿廓transverse tooth profile
端面重合度transverse contact ratio端面模数transverse module端面压力角transverse pressure angle 锻造forge对称循环应力symmetry circulating stress对心滚子从动件radial (or in-line ) roller follower 对心直动从动件radial (or in-line ) translating follower
对心移动从动件radial reciprocating follower
对心曲柄滑块机构in-line slider-crank (or crank-slider) mechanism多列轴承multi-row bearing
多楔带poly V-belt多项式运动规律polynomial motion多质量转子rotor with several masses
惰轮idle gear额定寿命rating life额定载荷load ratingII 级杆组dyad发生线generating line
发生面generating plane 法面normal plane法面参数normal parameters法面齿距normal circular pitch 法面模数normal module法面压力角normal pressure angle法向齿距normal pitch
法向齿廓normal tooth profile法向直廓蜗杆straight sided normal worm法向力normal force
反馈式组合feedback combining反向运动学inverse ( or backward) kinematics
反转法kinematic inversion反正切Arctan范成法generating cutting仿形法form cutting
方案设计、概念设计concept design, CD防振装置shockproof device飞轮flywheel
飞轮矩moment of flywheel非标准齿轮nonstandard gear非接触式密封non-contact seal
非周期性速度波动aperiodic speed fluctuation非圆齿轮non-circular gear粉末合金powder metallurgy
分度线reference line; standard pitch line
分度圆reference circle; standard (cutting) pitch circle分度圆柱导程角lead angle at reference cylinder
分度圆柱螺旋角helix angle at reference cylinder分母denominator分子numerator
分度圆锥reference cone; standard pitch cone分析法analytical method封闭差动轮系planetary differential 复合铰链compound hinge复合式组合compound combining复合轮系compound (or combined) gear train 复合平带compound flat belt复合应力combined stress复式螺旋机构Compound screw mechanism
复杂机构complex mechanism杆组Assur group 干涉interference 刚度系数stiffness coefficient
刚轮rigid circular spline钢丝软轴wire soft shaft刚体导引机构body guidance mechanism
刚性冲击rigid impulse (shock)刚性转子rigid rotor刚性轴承rigid bearing刚性联轴器rigid coupling
高度系列height series高速带high speed belt高副higher pair格拉晓夫定理Grashoff`s law
根切undercutting公称直径nominal diameter高度系列height series功work
工况系数application factor工艺设计technological design
工作循环图working cycle diagram工作机构operation mechanism工作载荷external loads
工作空间working space工作应力working stress工作阻力effective resistance
工作阻力矩effective resistance moment公法线common normal line公共约束general constraint
公制齿轮丨metric gears功率power功能分析设计function analyses design共轭齿廓conjugate profiles 共轭凸轮conjugate cam构件link鼓风机blower固定构件fixed link; frame固体润滑剂solid lubricant 关节型操作器jointed manipulator惯性力inertia force惯性力矩moment of inertia ,shaking moment
惯性力平衡balance of shaking force惯性力完全平衡full balance of shaking force
惯性力部分平衡partial balance of shaking force惯性主矩resultant moment of inertia
惯性主失resultant vector of inertia冠轮crown gear广义机构generation mechanism
广义坐标generalized coordinate轨迹生成path generation轨迹发生器path generator
滚刀hob滚道raceway滚动体rolling element滚动轴承rolling bearing
滚动轴承代号rolling bearing identification code滚针needle roller滚针轴承needle roller bearing
滚子roller滚子轴承roller bearing滚子半径radius of roller滚子从动件roller follower
滚子链roller chain滚子链联轴器double roller chain coupling滚珠丝杆ball screw
滚柱式单向超越离合器roller clutch过度切割undercutting函数发生器function generator
函数生成function generation 含油轴承oil bearing耗油量oil consumption
耗油量系数oil consumption factor赫兹公式H. Hertz equation
合成弯矩resultant bending moment合力resultant force合力矩resultant moment of force
黑箱black box横坐标abscissa互换性齿轮interchangeable gears花键spline滑键、导键feather key
滑动轴承sliding bearing滑动率sliding ratio滑块slider环面蜗杆toroid helicoids worm
环形弹簧annular spring缓冲装置shocks; shock-absorber灰铸铁grey cast iron回程return
回转体平衡balance of rotors混合轮系compound gear train积分integrate
机电一体化系统设计mechanical-electrical integration system design
机构mechanism机构分析analysis of mechanism机构平衡balance of mechanism
机构学mechanism机构运动设计kinematic design of mechanism
机构运动简图kinematic sketch of mechanism机构综合synthesis of mechanism
机构组成constitution of mechanism机架frame, fixed link机架变换kinematic inversion
机器machine机器人robot机器人操作器manipulator机器人学robotics
技术过程technique process技术经济评价technical and economic evaluation
技术系统technique system机械machinery机械创新设计mechanical creation design, MCD
机械系统设计mechanical system design, MSD机械动力分析dynamic analysis of machinery
机械动力设计dynamic design of machinery机械动力学dynamics of machinery
机械的现代设计modern machine design
机械系统mechanical system机械利益mechanical advantage机械平衡balance of machinery
机械手manipulator机械设计machine design; mechanical design
机械特性mechanical behavior机械调速mechanical speed governors机械效率mechanical efficiency 机械原理theory of machines and mechanisms
机械运转不均匀系数coefficient of speed fluctuation机械无级变速mechanical stepless speed changes 基础机构fundamental mechanism基本额定寿命basic rating life基于实例设计case-based design,CBD 基圆base circle基圆半径radius of base circle基圆齿距base pitch
基圆压力角pressure angle of base circle基圆柱base cylinder基圆锥base cone
急回机构quick-return mechanism急回特性quick-return characteristics
急回系数advance-to return-time ratio急回运动quick-return motion
棘轮ratchet棘轮机构ratchet mechanism棘爪pawl极限位置extreme (or limiting) position
极位夹角crank angle between extreme (or limiting) positions
计算机辅助设计computer aided design, CAD
计算机辅助制造computer aided manufacturing, CAM
计算机集成制造系统computer integrated manufacturing system, CIMS
计算力矩factored moment; calculation moment计算弯矩calculated bending moment
加权系数weighting efficient加速度acceleration加速度分析acceleration analysis
加速度曲线acceleration diagram尖点pointing; cusp尖底从动件knife-edge follower
间隙backlash间歇运动机构intermittent motion mechanism减速比reduction ratio
减速齿轮、减速装置reduction gear
减速器speed reducer减摩性anti-friction quality渐开螺旋面involute helicoid
渐开线involute渐开线齿廓involute profile渐开线齿轮involute gear
渐开线发生线generating line of involute渐开线方程involute equation
渐开线函数involute function渐开线蜗杆involute worm渐开线压力角pressure angle of involute
渐开线花键involute spline简谐运动simple harmonic motion键key键槽keyway
交变应力repeated stress交变载荷repeated fluctuating load交叉带传动cross-belt drive
交错轴斜齿轮crossed helical gears胶合scoring角加速度angular acceleration
角速度angular velocity角速比angular velocity ratio角接触球轴承angular contact ball bearing
角接触推力轴承angular contact thrust bearing角接触向心轴承angular contact radial bearing
角接触轴承angular contact bearing铰链、枢纽hinge校正平面correcting plane
接触应力contact stress接触式密封contact seal阶梯轴multi-diameter shaft结构structure
结构设计structural design截面section节点pitch point节距circular pitch; pitch of teeth
节线pitch line节圆pitch circle节圆齿厚thickness on pitch circle节圆直径pitch diameter
节圆锥pitch cone节圆锥角pitch cone angle解析设计analytical design
紧边tight-side紧固件fastener径节diametral pitch径向radial direction
径向当量动载荷dynamic equivalent radial load径向当量静载荷static equivalent radial load
径向基本额定动载荷basic dynamic radial load rating径向基本额定静载荷basic static radial load tating 径向接触轴承radial contact bearing径向平面radial plane径向游隙radial internal clearance
径向载荷radial load径向载荷系数radial load factor径向间隙clearance静力static force
静平衡static balance静载荷static load静密封static seal局部自由度passive degree of freedom
矩阵matrix矩形螺纹square threaded form锯齿形螺纹buttress thread form
矩形牙嵌式离合器square-jaw positive-contact clutch绝对尺寸系数absolute dimensional factor
绝对运动absolute motion绝对速度absolute velocity均衡装置load balancing mechanism
抗压强度compression strength 开口传动open-belt drive 开式链open kinematic chain
开链机构open chain mechanism可靠度degree of reliability可靠性reliability
可靠性设计reliability design, RD空气弹簧air spring空间机构spatial mechanism
空间连杆机构spatial linkage空间凸轮机构spatial cam
空间运动副spatial kinematic pair空间运动链spatial kinematic chain
空转idle宽度系列width series框图block diagram雷诺方程Reynolds‘s equation
离心力centrifugal force 离心应力centrifugal stress离合器clutch离心密封centrifugal seal
理论廓线pitch curve理论啮合线theoretical line of action隶属度membership力force
力多边形force polygon力封闭型凸轮机构force-drive (or force-closed) cam mechanism
力矩moment力平衡equilibrium力偶couple力偶矩moment of couple连杆connecting rod, coupler 连杆机构linkage连杆曲线coupler-curve连心线line of centers链chain
链传动装置chain gearing链轮sprocket ; sprocket-wheel ; sprocket gear ; chain wheel
联组V 带tight-up V belt联轴器coupling ; shaft coupling两维凸轮two-dimensional cam
临界转速critical speed六杆机构six-bar linkage龙门刨床double Haas planer
轮坯blank轮系gear train螺杆screw螺距thread pitch螺母screw nut
螺旋锥齿轮helical bevel gear螺钉screws螺栓bolts螺纹导程lead螺纹效率screw efficiency
螺旋传动power screw螺旋密封spiral seal螺纹thread (of a screw)螺旋副helical pair
螺旋机构screw mechanism螺旋角helix angle螺旋线helix ,helical line
绿色设计green design ; design for environment马耳他机构Geneva wheel ; Geneva gear
马耳他十字Maltese cross 脉动无级变速pulsating stepless speed changes
脉动循环应力fluctuating circulating stress脉动载荷fluctuating load铆钉rivet
迷宫密封labyrinth seal密封seal密封带seal belt密封胶seal gum密封元件potted component
密封装置sealing arrangement面对面安装face-to-face arrangement
面向产品生命周期设计design for product`s life cycle, DPLC名义应力、公称应力nominal stress
模块化设计modular design, MD模块式传动系统modular system模幅箱morphology box
模糊集fuzzy set模糊评价fuzzy evaluation模数module摩擦friction
摩擦角friction angle摩擦力friction force摩擦学设计tribology design, TD
摩擦阻力frictional resistance摩擦力矩friction moment摩擦系数coefficient of friction
摩擦圆friction circle磨损abrasion ;wear; scratching末端执行器end-effector
目标函数objective function耐腐蚀性corrosion resistance 耐磨性wear resistance
挠性机构mechanism with flexible elements挠性转子flexible rotor内齿轮internal gear
内齿圈ring gear内力internal force内圈inner ring能量energy
能量指示图viscosity逆时针counterclockwise (or anticlockwise)
啮出engaging-out啮合engagement, mesh, gearing啮合点contact points
啮合角working pressure angle啮合线line of action啮合线长度length of line of action
啮入engaging-in牛头刨床shaper凝固点freezing point; solidifying point
扭转应力torsion stress扭矩moment of torque扭簧helical torsion spring诺模图Nomogram
O 形密封圈密封O ring seal盘形凸轮disk cam 盘形转子disk-like rotor
抛物线运动parabolic motion疲劳极限fatigue limit疲劳强度fatigue strength偏置式offset
偏( 心) 距offset distance偏心率eccentricity ratio偏心质量eccentric mass
偏距圆offset circle偏心盘eccentric偏置滚子从动件offset roller follower
偏置尖底从动件offset knife-edge follower偏置曲柄滑块机构offset slider-crank mechanism
拼接matching评价与决策evaluation and decision频率frequency平带flat belt
平带传动flat belt driving平底从动件flat-face follower平底宽度face width
平分线bisector平均应力average stress平均中径mean screw diameter平均速度average velocity
平衡balance平衡机balancing machine平衡品质balancing quality平衡平面correcting plane
平衡质量balancing mass
平衡重counterweight平衡转速balancing speed平面副planar pair, flat pair平面机构planar mechanism 平面运动副planar kinematic pair平面连杆机构planar linkage平面凸轮planar cam
平面凸轮机构planar cam mechanism平面轴斜齿轮parallel helical gears普通平键parallel key
其他常用机构other mechanism in common use 起动阶段starting period
启动力矩starting torque气动机构pneumatic mechanism奇异位置singular position
起始啮合点initial contact , beginning of contact气体轴承gas bearing千斤顶jack
嵌入键sunk key强迫振动forced vibration切齿深度depth of cut曲柄crank
曲柄存在条件Grashoff`s law曲柄导杆机构crank shaper (guide-bar) mechanism
曲柄滑块机构slider-crank (or crank-slider) mechanism曲柄摇杆机构crank-rocker mechanism
曲齿锥齿轮spiral bevel gear曲率curvature曲率半径radius of curvature曲面从动件curved-shoe follower 曲线拼接curve matching曲线运动curvilinear motion曲轴crank shaft驱动力driving force
驱动力矩driving moment (torque)全齿高whole depth权重集weight sets球ball球面滚子convex roller 球轴承ball bearing球面副spheric pair球面渐开线spherical involute球面运动spherical motion
球销副sphere-pin pair
球坐标操作器polar coordinate manipulator燃点spontaneous ignition
热平衡heat balance; thermal equilibrium 人字齿轮herringbone gear
冗余自由度redundant degree of freedom柔轮flexspline柔性冲击flexible impulse; soft shock
柔性制造系统flexible manufacturing system; FMS柔性自动化flexible automation
润滑油膜lubricant film润滑装置lubrication device润滑lubrication润滑剂lubricant
三角形花键serration spline 三角形螺纹V thread screw 三维凸轮three-dimensional cam
三心定理Kennedy`s theorem砂轮越程槽grinding wheel groove砂漏hour-glass
少齿差行星传动planetary drive with small teeth difference
设计方法学design methodology设计变量design variable设计约束design constraints
深沟球轴承deep groove ball bearing生产阻力productive resistance升程rise升距lift
实际廓线cam profile十字滑块联轴器double slider coupling; Oldham‘s coupling
矢量vector输出功output work输出构件output link输出机构output mechanism
输出力矩output torque输出轴output shaft输入构件input link数学模型mathematic model
实际啮合线actual line of action双滑块机构double-slider mechanism, ellipsograph
双曲柄机构double crank mechanism双曲面齿轮hyperboloid gear
双头螺柱studs双万向联轴节constant-velocity (or double) universal joint
双摇杆机构double rocker mechanism
双转块机构Oldham coupling双列轴承double row bearing
双向推力轴承double-direction thrust bearing松边slack-side顺时针clockwise
瞬心instantaneous center死点dead point四杆机构four-bar linkage
速度velocity速度不均匀( 波动) 系数coefficient of speed fluctuation
速度波动speed fluctuation速度曲线velocity diagram
速度瞬心instantaneous center of velocity塔轮step pulley 踏板pedal 台钳、虎钳vice
太阳轮sun gear弹性滑动elasticity sliding motion
弹性联轴器elastic coupling ; flexible coupling
弹性套柱销联轴器rubber-cushioned sleeve bearing coupling套筒sleeve
梯形螺纹acme thread form特殊运动链special kinematic chain特性characteristics
替代机构equivalent mechanism调节modulation, regulation调心滚子轴承self-aligning roller bearing 调心球轴承self-aligning ball bearing调心轴承self-aligning bearing调速speed governing
调速电动机adjustable speed motors调速系统speed control system调压调速variable voltage control 调速器regulator, governor铁磁流体密封ferrofluid seal停车阶段stopping phase停歇dwell
同步带synchronous belt同步带传动synchronous belt drive凸的，凸面体convex凸轮cam
凸轮倒置机构inverse cam mechanism凸轮机构cam , cam mechanism凸轮廓线cam profile
凸轮廓线绘制layout of cam profile凸轮理论廓线pitch curve凸缘联轴器flange coupling
图册、图谱atlas图解法graphical method推程rise推力球轴承thrust ball bearing
推力轴承thrust bearing退刀槽tool withdrawal groove退火anneal陀螺仪gyroscope
V 带V belt外力external force 外圈outer ring 外形尺寸boundary dimension
万向联轴器Hooks coupling ; universal coupling外齿轮external gear弯曲应力beading stress
弯矩bending moment腕部wrist往复移动reciprocating motion往复式密封reciprocating seal
网上设计on-net design, OND微动螺旋机构differential screw mechanism位移displacement
位移曲线displacement diagram位姿pose , position and orientation
稳定运转阶段steady motion period稳健设计robust design蜗杆worm蜗杆传动机构worm gearing 蜗杆头数number of threads蜗杆直径系数diametral quotient蜗杆蜗轮机构worm and worm gear
蜗杆形凸轮步进机构worm cam interval mechanism蜗杆旋向hands of worm蜗轮worm gear
涡圈形盘簧power spring无级变速装置stepless speed changes devices无穷大infinite
系杆crank arm, planet carrier 现场平衡field balancing 向心轴承radial bearing
向心力centrifugal force
相对速度relative velocity相对运动relative motion相对间隙relative gap象限quadrant
橡皮泥plasticine细牙螺纹fine threads销pin消耗consumption小齿轮pinion
小径minor diameter橡胶弹簧balata spring
修正梯形加速度运动规律modified trapezoidal acceleration motion
修正正弦加速度运动规律modified sine acceleration motion
斜齿圆柱齿轮helical gear斜键、钩头楔键taper key泄漏leakage谐波齿轮harmonic gear
谐波传动harmonic driving谐波发生器harmonic generator
斜齿轮的当量直齿轮equivalent spur gear of the helical gear心轴spindle
行程速度变化系数coefficient of travel speed variation行程速比系数advance-to return-time ratio
行星齿轮装置planetary transmission行星轮planet gear
行星轮变速装置planetary speed changing devices行星轮系planetary gear train
形封闭凸轮机构positive-drive (or form-closed) cam mechanism虚拟现实virtual reality
虚拟现实技术virtual reality technology, VRT虚拟现实设计virtual reality design, VRD
虚约束redundant (or passive) constraint许用不平衡量allowable amount of unbalance
许用压力角allowable pressure angle许用应力allowable stress; permissible stress
悬臂结构cantilever structure悬臂梁cantilever beam循环功率流circulating power load
旋转力矩running torque旋转式密封rotating seal旋转运动rotary motion选型type selection
压力pressure 压力中心center of pressure
压缩机compressor压应力compressive stress压力角pressure angle
牙嵌式联轴器jaw (teeth) positive-contact coupling雅可比矩阵Jacobi matrix摇杆rocker
液力传动hydrodynamic drive液力耦合器hydraulic couplers液体弹簧liquid spring
液压无级变速hydraulic stepless speed changes液压机构hydraulic mechanism
一般化运动链generalized kinematic chain移动从动件reciprocating follower
移动副prismatic pair, sliding pair移动关节prismatic joint移动凸轮wedge cam
盈亏功increment or decrement work应力幅stress amplitude
应力集中stress concentration应力集中系数factor of stress concentration
应力图stress diagram应力—应变图stress-strain diagram优化设计optimal design
油杯oil bottle油壶oil can油沟密封oily ditch seal有害阻力useless resistance
有益阻力useful resistance有效拉力effective tension有效圆周力effective circle force
有害阻力detrimental resistance余弦加速度运动cosine acceleration (or simple harmonic) motion
预紧力preload原动机primer mover圆带round belt圆带传动round belt drive
圆弧齿厚circular thickness圆弧圆柱蜗杆hollow flank worm圆角半径fillet radius
圆盘摩擦离合器disc friction clutch圆盘制动器disc brake原动机prime mover
原始机构original mechanism圆形齿轮circular gear
圆柱滚子cylindrical roller圆柱滚子轴承cylindrical roller bearing圆柱副cylindric pair
圆柱式凸轮步进运动机构barrel (cylindric) cam
圆柱螺旋拉伸弹簧cylindroid helical-coil extension spring
圆柱螺旋扭转弹簧cylindroid helical-coil torsion spring
圆柱螺旋压缩弹簧cylindroid helical-coil compression spring圆柱凸轮cylindrical cam
圆柱蜗杆cylindrical worm圆柱坐标操作器cylindrical coordinate manipulator
圆锥螺旋扭转弹簧conoid helical-coil compression spring圆锥滚子tapered roller
圆锥滚子轴承tapered roller bearing圆锥齿轮机构bevel gears
圆锥角cone angle原动件driving link约束constraint约束条件constraint condition
约束反力constraining force跃度jerk跃度曲线jerk diagram
运动倒置kinematic inversion运动方案设计kinematic precept design
运动分析kinematic analysis运动副kinematic pair运动构件moving link运动简图kinematic sketch 运动链kinematic chain运动失真undercutting运动设计kinematic design运动周期cycle of motion 运动综合kinematic synthesis运转不均匀系数coefficient of velocity fluctuation
运动粘度kenematic viscosity载荷load 载荷—变形曲线load—deformation curve
载荷—变形图load—deformation diagram窄V 带narrow V belt毡圈密封felt ring seal
展成法generating张紧力tension张紧轮tension pulley振动vibration振动力矩shaking couple
振动频率frequency of vibration振幅amplitude of vibration正切机构tangent mechanism
正向运动学direct (forward) kinematics正弦机构sine generator, scotch yoke
织布机loom正应力、法向应力normal stress制动器brake直齿圆柱齿轮spur gear
直齿锥齿轮straight bevel gear直角三角形right triangle
直角坐标操作器Cartesian coordinate manipulator直径系数diametral quotient
直径系列diameter series直廓环面蜗杆hindley worm直线运动linear motion
直轴straight shaft质量mass质心center of mass执行构件executive link; working link
质径积mass-radius product智能化设计intelligent design, ID中间平面mid-plane
中心距center distance中心距变动center distance change中心轮central gear
中径mean diameter终止啮合点final contact, end of contact周节pitch
周期性速度波动periodic speed fluctuation周转轮系epicyclic gear train肘形机构toggle mechanism 轴shaft轴承盖bearing cup轴承合金bearing alloy
轴承座bearing block轴承高度bearing height
轴承宽度bearing width轴承内径bearing bore diameter轴承寿命bearing life轴承套圈bearing ring 轴承外径bearing outside diameter轴颈journal轴瓦、轴承衬bearing bush
轴端挡圈shaft end ring轴环shaft collar轴肩shaft shoulder轴角shaft angle
轴向axial direction轴向齿廓axial tooth profile轴向当量动载荷dynamic equivalent axial load
轴向当量静载荷static equivalent axial load轴向基本额定动载荷basic dynamic axial load rating
轴向基本额定静载荷basic static axial load rating轴向接触轴承axial contact bearing
轴向平面axial plane轴向游隙axial internal clearance轴向载荷axial load
轴向载荷系数axial load factor轴向分力axial thrust load主动件driving link主动齿轮driving gear 主动带轮driving pulley转动导杆机构whitworth mechanism转动副revolute (turning) pair
转速swiveling speed ; rotating speed转动关节revolute joint转轴revolving shaft
转子rotor转子平衡balance of rotor装配条件assembly condition锥齿轮bevel gear
锥顶common apex of cone锥距cone distance锥轮bevel pulley; bevel wheel
锥齿轮的当量直齿轮equivalent spur gear of the bevel gear
锥面包络圆柱蜗杆milled helicoids worm准双曲面齿轮hypoid gear子程序subroutine
子机构sub-mechanism自动化automation自锁self-locking自锁条件condition of self-locking
自由度degree of freedom, mobility总重合度total contact ratio总反力resultant force
总效率combined efficiency; overall efficiency组成原理theory of constitution
组合齿形composite tooth form组合安装stack mounting
组合机构combined mechanism
阻抗力resistance
最大盈亏功maximum difference work between plus and minus work
纵向重合度overlap contact ratio
纵坐标ordinate
组合机构combined mechanism
最少齿数minimum teeth number
最小向径minimum radius
作用力applied force
坐标系coordinate frame
PCB专业术语中英文翻译【VIP专享】
PCB 专业术语中英文翻译 很多PCB 的书上使用的是英文，但是大多数的人又看不懂英文， 这时候怎么办呢，我们需要翻译，但是如果每看到一个不会的词 儿就去翻译，那么就太耗费时间了，所以我们捷多邦总结了一些 常用的专业术语的中英文对照，希望能对大家有用。 1.印制电路：printed circuit 2.印制线路：printed wiring 3.印制板：printed board 4.印制板电路：printed circuit board (pcb) 5.印制线路板：printed wiring board(pwb) 6.印制元件：printed component 7.印制接点：printed contact 8.印制板装配：printed board assembly 9.板：board 1 10.表面层合电路板：surface laminar circuit (slc) 11.埋入凸块连印制板：b2it printed board 12.多层膜基板：multi-layered film substrate(mfs) 13.层间全内导通多层印制板：alivh multilayer printed board 14.载芯片板：chip on board (cob) 15.埋电阻板：buried resistance board 16.母板：mother board 17.单面印制板：single-sided printed board(ssb) 、管路敷设技术通过管线不仅可以解决吊顶层配置不规范高中资料试卷问题，而且可保障各类管路习题到位。在管路敷设过程中，要加强看护关于管路高中资料试卷连接管口处理高中资料试卷弯扁度固定盒位置保护层防腐跨接地线弯曲半径标等，要求技术交底。管线敷设技术中包含线槽、管架等多项方式，为解决高中语文电气课件中管壁薄、接口不严等问题，合理利用管线敷设技术。线缆敷设原则：在分线盒处，当不同电压回路交叉时，应采用金属隔板进行隔开处理；同一线槽内强电回路须同时切断习题电源，线缆敷设完毕，要进行检查和检测处理。、电气课件中调试对全部高中资料试卷电气设备，在安装过程中以及安装结束后进行 高中资料试卷调整试验；通电检查所有设备高中资料试卷相互作用与相互关系，根据生产工艺高中资料试卷要求，对电气设备进行空载与带负荷下高中资料试卷调控试验；对设备进行调整使其在正常工况下与过度工作下都可以正常工作；对于继电保护进行整核对定值，审核与校对图纸，编写复杂设备与装置高中资料试卷调试方案，编写重要设备高中资料试卷试验方案以及系统启动方案；对整套启动过程中高中资料试卷电气设备进行调试工作并且进行过关运行高中资料试卷技术指导。对于调试过程中高中资料试卷技术问题，作为调试人员，需要在事前掌握图纸资料、设备制造厂家出具高中资料试卷试验报告与相关技术资料，并且了解现场设备高中资料试卷布置情况与有关高中资料试卷电气系统接线等情况 ，然后根据规范与规程规定，制定设备调试高中资料试、电气设备调试高中资料试卷技术电力保护装置调试技术，电力保护高中资料试卷配置技术是指机组在进行继电保护高中资料试卷总体配置时，需要在最大限度内来确保机组高中资料试卷安全，并且尽可能地缩小故障高中资料试卷破坏范围，或者对某些异常高中资料试卷工况进行自动处理，尤其要避免错误高中资料试卷保护装置动作，并且拒绝动作，来避免不必要高中资料试卷突然停机。因此，电力高中资料试卷保护装置调试技术，要求电力保护装置做到准确灵活。对于差动保护装置高中资料试卷调试技术是指发电机一变压器组在发生内部故障时，需要进行外部电源高中资料试卷切除从而采用高中资料试卷主要保护装置。
冲压模具专业词汇中英文翻译
Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号
机械图纸中英文翻译2(1)1
近几年，我厂和英国、西班牙的几个公司有业务往来，外商传真发来的图纸都是英文标注，平时阅看有一定的困难。下面把我们积累的几点看英文图纸的经验与同行们交流。 1标题栏 英文工程图纸的右下边是标题栏（相当于我们的标题栏和部分技术要求），其中有图纸名称（TILE）、设计者（DRAWN）、审查者（CHECKED）、材料（MATERIAL）、日期（DATE）、比例（SCALE）、热处理（HEAT TREATMENT）和其它一些要求，如： 1)TOLERANCES UNLESS OTHERWISE SPECIFIAL 未注公差。 2)DIMS IN mm UNLESS STATED 如不做特殊要求以毫米为单位。 3)ANGULAR TOLERANCE±1°角度公差±1°。 4)DIMS TOLERANCE±0.1未注尺寸公差±0.1。 5)SURFACE FINISH 3.2 UNLESS STATED未注粗糙度3.2。 2常见尺寸的标注及要求 2.1孔（HOLE）如： （1）毛坯孔：3"DIAO+1CORE 芯子3"0+1; （2）加工孔：1"DIA1"; （3）锪孔：锪孔(注C＇BORE=COUNTER BORE锪底面孔); （4）铰孔：1"/4 DIA REAM铰孔1"/4; （5）螺纹孔的标注一般要表示出螺纹的直径，每英寸牙数（螺矩）、螺纹种类、精度等级、钻深、攻深，方向等。如：例1.6 HOLES EQUI-SPACED ON 5"DIA (6孔均布在5圆周上（EQUI-SPACED=EQUALLY SPACED均布） DRILL 1"DIATHRO＇ 钻1"通孔（THRO＇=THROUGH通） C/SINK22×6DEEP 沉孔22×6 例2.TAP7"/8-14UNF-3BTHRO＇ 攻统一标准细牙螺纹，每英寸14牙，精度等级3B级 （注UNF=UNIFIED FINE THREAD美国标准细牙螺纹） 1"DRILL 1"/4-20 UNC-3 THD7"/8 DEEP 4HOLES NOT BREAK THRO钻1"孔，攻1"/4美国粗牙螺纹，每英寸20牙，攻深7"/8,4孔不准钻通（UNC=UCIFIED COARSE THREAD 美国标准粗牙螺纹） 1"-14NS-2THRO 攻美国固定特种螺纹M1",每英寸牙数14,精度等级为二级 （注NS=NATIONAL SPECIAL THREAD:美国固定特种标准）
机械专业术语英文翻译
陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking
技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams
(机械制造行业)机械英文翻译
英文翻译 机械设计 一台完整机器的设计是一个复杂的过程。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。 Machine Design The complete design of a machine is a complex process. The machine design is a creative work. Project engineer not only must have the creativity in the work, but also must in aspect and so on mechanical drawing, kinematics, engineerig material, materials mechanics and machine manufacture technology has the deep elementary knowledge. 任何产品在设计时第一步就是选择产品每个部分的构成材料。许多的材料被今天的设计师所使用。对产品的功能，它的外观、材料的成本、制造的成本作出必要的选择是十分重要的。对材料的特性必须事先作出仔细的评估。 One of the first steps in the design of any product is to select the material from which each part is to be made. Numerous materials are available to today's designers. The function of the product, its appearance, the cost of the material, and the cost of fabrication are important in making a selection. A careful evaluation of the properties of a. material must be made prior to any calculations. 仔细精确的计算是必要的，以确保设计的有效性。在任何失败的情况下，最好知道在最初设计中有有缺陷的部件。计算（图纸尺寸）检查是非常重要的。一个小数点的位置放错，就可以导致一个本可以完成的项目失败。设计工作的各个方面都应该检查和复查。 Careful calculations are necessary to ensure the validity of a design. In case of any part failures, it is desirable to know what was done in originally designing the defective components. The checking of calculations (and drawing dimensions) is of utmost importance. The misplacement of one decimal point can ruin an otherwise acceptable project. All aspects of design work should be checked and rechecked. 计算机是一种工具，它能够帮助机械设计师减轻繁琐的计算，并对现有数据提供进一步的分析。互动系统基于计算机的能力，已经使计算机辅助设计（CAD）和计算机辅助制造（CAM）成为了可能。心理学家经常谈论如何使人们适应他们所操作的机器。设计人员的基本职责是努力使机器来适应人们。这并不是一项容易的工作，因为实际上并不存在着一个对所有人来说都是最优的操作范围和操作
市场营销专业术语中英文对照标准翻译
市场营销专业术语中英文对照标准翻译 本文为市场营销中经常用到的一些中文与英文互译的标准用语，希望对市场营销从业人员有所帮助。 《财富》杂志Fortune 案头调研Desk Research 奥美公司Ogilvy & Mather 白色商品White Goods 百乐门Parliament 百威啤酒Budweiser 包裹销售法Banded Pack 宝洁公司Procter & Gamble 宝丽来Polaroid 宝马BMW 边际成本Marginal Cost 边际收益Marginal Benefit 标准差，均差Standard Deviation 别克Buick 波立兹调查公司Alfred Politz Research, Inc 波旁王朝Ancient Age Bourbon 波特福洛分析Portefolio Analysis 产品差异Product Differentiation 产品生命周期Product Life Cycle 产品系列Product Line 产品组合Product Mix 阐述Presentation 超级市场Supermarket 成对比较法Paired Comparisons 成功的理想主义者Successful Idealist 承诺型消费者Committed Buyer 程度测试Tachistoscope 橙色商品Orange Goods 冲动购买Impulse Buying 重叠率Duplication 抽样Sampling 传销Pyramid Selling 传阅发行量Pass-on Circulation 词语联想法Word Associaton 刺激营销Incentive Marketing 促销Promotion 达彼思广告公司Ted Bates & Copany 大卫·奥格威David Ogilvy 戴比尔斯De Beers
机械专业外文翻译中英文翻译
外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are
机械图纸英语翻译
1，PERMANENTLY MARK PART NUMBER(ALL METHODS ACCEPTABLE)IN LOCATION SHOWN：SAME AS DWG NO.INCLUDING REV & DATE OF MFG 2，REMOVE ALL BURRS AND BREAK ALL EDGES 3，ALL DIMENSIONS AND TOLERANCES APPLY AFTER FINISHING(IF REQUIRED) 4，COSMETIC INSPECTION CLASS IIA-EXTERNAL COMPONENT 5，MATERIAL：LAMINATED 1/2" CORIAN；COLOR SPECIFIED IN PURCHASE ORDER 6，FINISH：LAMINATION TO APPEAR SEAMLESS;NO PITTS OR LINES POST MACHINING：CLEAN & FURTHER SPECIFICATION IN PO 7，POLISHING：IF SPECIFIED IN PO；TOP，SIDES，CHAMFER & 1/2" FROM EDGE ON BASE SURFACE 8，ARTWORK：IF SPECIFIED IN PO；TO BE READ FROM ELLIPTICAL PROFILE 9，PART TO BE MANUFACTURED REFERENCING DWG AND 3D GEOMETRY SUPPLIED 2，1.如图所示的位置上加上耐久的产品编号标记,就是图纸编号包括图纸版本号及生产日期. 2.除去所有毛刺及所有边倒角. 3.(如必要的话)产品表面处理后,所有的尺寸及公差要符合要求. 4.外观检测等级为【信息工业协会[美]-外观件】 5.产品材料:1/2 英寸厚的"可丽耐"薄板, 颜色在采购单内注明. 6.表面要求:层压后无结合线,无凹坑或凸凹线状, 后处理: 洁净及详细请看采购单说明. 7.表面抛光: 如果在采购单中有说明则按其要求做,否则顶部,侧面,倒角斜面及底边上来1/2英寸处要抛光. 8.美工; 如果在采购单中有说明则按其要求做,否则从椭圆形中来读取(这一点要能与你们专业有关,我就不是很清楚, 要看产品图才知) 9.产品加工请参照提供的工程图及三维立体图. Assembly line 组装线 Layout 布置图 Conveyer 流水线物料板 Rivet table 拉钉机 Rivet gun 拉钉枪 Screw driver 起子 Electric screw driver 电动起子 Pneumatic screw driver 气动起子 worktable 工作桌 OOBA 开箱检查 fit together 组装在一起 fasten 锁紧(螺丝) fixture 夹具(治具) pallet 栈板
机械专业相关词汇中英文翻译大全
机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus
专业名词对应英文翻译
预约券reservation ticket 下午茶high tea 微博Microblog/ Tweets 裸婚naked wedding 亚健康sub-health 平角裤boxers 愤青young cynic 灵魂伴侣soul mate 小白脸toy boy 精神出轨soul infidelity 人肉搜索flesh search 剩女3S lady（single，seventies,stuck）/left girls 山寨copycat 异地恋long-distance relationship 性感妈妈yummy mummy 钻石王老五diamond bachelor 时尚达人fashion icon 上相的,上镜头的photogenic 学术界academic circle 哈证族certificate maniac 偶像派idol type 住房公积金housing funds 熟女cougar（源自电影Cougar Club） 挑食者picky-eater 伪球迷fake fans 紧身服straitjacket 团购group buying 奉子成婚shotgun marriage 婚前性行为premarital sex 炫富flaunt wealth 决堤breaching of the dike 上市list share 赌球soccer gambling 桑拿天sauna weather 自杀Dutch act 假发票fake invoice 金砖四国BRIC countries 笑料laughing stock 泰国香米Thai fragrant rice 学历造假fabricate academic credentials 泄洪release flood waters 狂热的gaga eg: I was gaga over his deep blue eyes when I first set eyes on him 防暑降温补贴high temperature subsidy 暗淡前景bleak prospects
机械专业术语英文翻译
机械专业英语词汇 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing 尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker
机械专业英文翻译
机械专业英文翻译 Company number：【WTUT-WT88Y-W8BBGB-BWYTT-19998】
启动轴 starting axle 启动齿轮starting gear 启动棘轮 starting ratchet wheel 复位弹簧 restoring, pull back spring 弹簧座 spring seating 摩擦簧friction spring 推力垫圈 thrust washer 轴挡圈axle bumper ring 下料 filling 切断 cut 滚齿机 gear-hobbing machine 剪料机 material-shearing machine 车床 lathe 拉床 broaching machine 垂直度 verticality, vertical extent 平行度 parallelism同 心度 homocentricity 位置度 position 拉伤 pulling damage 碰伤 bumping damage 缺陷 deficiency 严重缺陷 severe deficiency 摩擦力 friction 扭距 twist 滑动 glide 滚动 roll 打滑 skid 脱不开 can’t seperate 不复位 can’t restore 直径 diameter M值 = 跨棒距 test rod span 公法线 common normal line 弹性 elasticity 频率特性 frequency characteristic 误差 error 响应 response 定位 allocation 机床夹具 jig 动力学 dynamic 运动学 kinematic 静力学 static 分析力学 analyse mechanics 拉伸 pulling 压缩 hitting 机床 machine tool 刀具 cutter 摩擦 friction 联结 link 传动 drive/transmission 轴 shaft 剪切 shear 扭转 twist 弯曲应力 bending stress 三相交流电 three-phase AC 磁路 magnetic circles 变压器 transformer 异步电动机 asynchronous motor 几何形状 geometrical 精度 precision 正弦形的 sinusoid 交流电路 AC circuit 机械加工余量 machining allowance 变形力 deforming force 变形 deformation 电路 circuit 半导体元件 semiconductor element 拉孔 broaching 装配 assembling 加工 machining 液压 hydraulic pressure 切线 tangent 机电一体化 mechanotronics mechanical-electrical integration 稳定性 stability 介质 medium 液压驱动泵 fluid clutch 液压泵 hydraulic pump 阀门 valve 失效 invalidation 强度 intensity 载荷 load 应力 stress 安全系数 safty factor 可靠性 reliability 螺纹 thread 螺旋 helix 键 spline 销 pin 滚动轴承 rolling bearing 滑动轴承 sliding bearing 弹簧 spring 制动器 arrester brake 十字结联轴节 crosshead 联轴器 coupling 链 chain 皮带 strap 精加工 finish machining 粗加工 rough machining 变速箱体 gearbox casing 腐蚀 rust 氧化 oxidation 磨损 wear 耐用度 durability 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking 技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams 反馈 feedback 发生器 generator
机械设计专业术语地英语的翻译
机械设计专业术语的英语翻译 阿基米德蜗杆 Archimedes worm 安全系数 safety factor; factor of safety 安全载荷 safe load 凹面、凹度 concavity 扳手 wrench 板簧 flat leaf spring 半圆键 woodruff key 变形 deformation 摆杆 oscillating bar 摆动从动件 oscillating follower 摆动从动件凸轮机构 cam with oscillating follower 摆动导杆机构 oscillating guide-bar mechanism 摆线齿轮 cycloidal gear 摆线齿形 cycloidal tooth profile 摆线运动规律 cycloidal motion 摆线针轮 cycloidal-pin wheel 包角 angle of contact 保持架 cage 背对背安装 back-to-back arrangement 背锥 back cone ； normal cone 背锥角 back angle 背锥距 back cone distance 比例尺 scale 比热容 specific heat capacity 闭式链 closed kinematic chain 闭链机构 closed chain mechanism 臂部 arm 变频器 frequency converters 变频调速 frequency control of motor speed 变速 speed change 变速齿轮 change gear ; change wheel 变位齿轮 modified gear 变位系数 modification coefficient 标准齿轮 standard gear 标准直齿轮 standard spur gear 表面质量系数 superficial mass factor 表面传热系数 surface coefficient of heat transfer 表面粗糙度 surface roughness 并联式组合 combination in parallel 并联机构 parallel mechanism 并联组合机构 parallel combined mechanism 并行工程 concurrent engineering 并行设计 concurred design, CD 不平衡相位 phase angle of unbalance 不平衡 imbalance (or unbalance) 不平衡量 amount of unbalance 不完全齿轮机构 intermittent gearing 波发生器 wave generator 波数 number of waves 补偿 compensation 参数化设计 parameterization design, PD 残余应力 residual stress 操纵及控制装置 operation control device 槽轮 Geneva wheel 槽轮机构 Geneva mechanism ； Maltese cross 槽数 Geneva numerate 槽凸轮 groove cam 侧隙 backlash 差动轮系 differential gear train 差动螺旋机构 differential screw mechanism 差速器 differential 常用机构 conventional mechanism; mechanism in common use 车床 lathe 承载量系数 bearing capacity factor 承载能力 bearing capacity 成对安装 paired mounting 尺寸系列 dimension series 齿槽 tooth space 齿槽宽 spacewidth 齿侧间隙 backlash 齿顶高 addendum 齿顶圆 addendum circle 齿根高 dedendum 齿根圆 dedendum circle 齿厚 tooth thickness 齿距 circular pitch 齿宽 face width 齿廓 tooth profile 齿廓曲线 tooth curve 齿轮 gear 齿轮变速箱 speed-changing gear boxes 齿轮齿条机构 pinion and rack 齿轮插刀 pinion cutter; pinion-shaped shaper cutter 齿轮滚刀 hob ,hobbing cutter 齿轮机构 gear 齿轮轮坯 blank 齿轮传动系 pinion unit 齿轮联轴器 gear coupling 齿条传动 rack gear 齿数 tooth number 齿数比 gear ratio
机械图纸英语翻译
机加工图纸有英语看不懂？不怕！史上最全翻译都在这里了机械图纸英语翻译 ALL WELDS CONTINUOUS UNLESS OTHERWISE STATED 未注焊缝均为连续焊 ALL WELDS 3mm FILLET UNLESS OTHERWISE STATED 未注焊角高3mm. ALL UNSPECIFIED RADI - R3 未注圆角R3 REMOVE ALL BURRS AND SHARP EDGES 棱角倒钝 CHANNEL 槽钢 RSA 708 角钢70X70X8 M30X1.5 pitch M30X1.5的锥螺纹 Tackweld 点焊 OD 1/4" outside dimension 1/4"的缩写外径直1/4"
75 CRS 尺寸为75 材质为冷轧钢板 410 OPENING REF 410 开口参考尺寸 40 REF 尺寸为40,参考值 2.5" BSP 2.5”圆锥管螺纹 2.5" BSPT HEXAGON 2.5”六角圆锥管螺纹(即对丝) 30x2.5 FLAT BAR 30X2.5 扁钢 TYP 2 POSNS 2处 11 TOTAL COILS APROX.9 WORKING COILS APROX.RIGHT HAND WOUND ONLY,END COILS SQUARE TO TOUCH. 总圈数约11圈；工作圈数约9圈；右旋；弹簧的端部磨平以便于接触.(此为弹簧技术说明)
FEMALE: 内扣(母扣) MALE: 外扣(公扣) 偏心轴eccentric shaft 销轴PIN 开口销COTTER PIN 螺杆screw 紧定螺钉SET SCREW 圆螺母ROUND NUT
机械专业中英文对照翻译大全.
机械专业英语词汇中英文对照翻译一览表 陶瓷ceramics 合成纤维synthetic fibre 电化学腐蚀electrochemical corrosion 车架automotive chassis 悬架suspension 转向器redirector 变速器speed changer 板料冲压sheet metal parts 孔加工spot facing machining 车间workshop 工程技术人员engineer 气动夹紧pneuma lock 数学模型mathematical model 画法几何descriptive geometry 机械制图Mechanical drawing 投影projection 视图view 剖视图profile chart 标准件standard component 零件图part drawing 装配图assembly drawing
尺寸标注size marking 技术要求technical requirements 刚度rigidity 内力internal force 位移displacement 截面section 疲劳极限fatigue limit 断裂fracture 塑性变形plastic distortion 脆性材料brittleness material 刚度准则rigidity criterion 垫圈washer 垫片spacer 直齿圆柱齿轮straight toothed spur gear 斜齿圆柱齿轮helical-spur gear 直齿锥齿轮straight bevel gear 运动简图kinematic sketch 齿轮齿条pinion and rack 蜗杆蜗轮worm and worm gear 虚约束passive constraint 曲柄crank 摇杆racker