路由器的综合配置

PC0:192.168.1.2 192.168.1.1
PC1:192.168.4.2 192.168.2.1

Switch>en
Switch#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Switch(config)#vlan 3
Switch(config-vlan)#exit
Switch(config)#vlan 31
Switch(config-vlan)#exit
Switch(config)#int vlan 3
Switch(config-if)#no shut

Switch(config-if)#ip address 192.168.1.1 255.255.255.0
Switch(config-if)#exit
Switch(config)#int vlan 31
Switch(config-if)#no shut


Switch(config-if)#ip address 192.168.2.1 255.255.255.0
Switch(config-if)#exit
Switch(config)#int fa 0/1
Switch(config-if)#switch access vlan 3
Switch(config-if)#

Switch(config-if)#exit
Switch(config)#int fa 0/2
Switch(config-if)#switch access vlan 31
Switch(config-if)#exit
Switch(config)#router rip
Switch(config)#version 2
Switch(config-router)#network 192.168.1.0
Switch(config-router)#network 192.168.2.0
Switch(config-router)#exit

Switch(config)#ip route 0.0.0.0 0.0.0.0 192.168.2.2
Switch(config)#exit
Switch#
%SYS-5-CONFIG_I: Configured from console by console

Switch#show run

Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa 0/0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet0/0, changed state to up

%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0, changed state to up

Router(config-if)#ip address 192.168.2.2 255.255.255.0
Router(config-if)#exit
Router(config)#int fa 1/0
Router(config-if)#no shut

Router(config-if)#
%LINK-5-CHANGED: Interface FastEthernet1/0, changed state to up

Router(config-if)#ip address 192.168.3.1 255.255.255.0
Router(config-if)#exit
Router(config)#router rip
Router(config-router)#version 2
Router(config-router)#network 192.168.2.0
Router(config-router)#exit
Router(config)#route ospf 1
Router(config-router)#network 192.168.3.0 0.0.0.255 area 0
Router(config-router)#exit
Router(config)#router rip
Router(config-router)#redistribute ospf 1
Router(config-router)#exit
Router(config)#route ospf 1
Router(config-router)#redistribute rip subnets
Router(config-router)#end





>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#int fa 0/0
Router(config-if)#no shut
Router(config-if)#ip address 192.168.4.1 255.255.255.0
Router(config-if)#exit
Router(config)#int fa 1/0
Router(config-if)#no shut
Router(config-if)#ip address 192.168.3.2 255.255.255.0
Router(config-if)#

Router(config-if)#exit

Router(config)#route ospf 1
Router(config-router)#network 192.168.4.0 0.0.0.255 area 0
Router(config-router)#network 192.168.3.0 0.0.0.255 area 0
Router(config-router)#
00:26:30: %OSPF-5-ADJCHG: Process 1, Nbr 192.168.22.1 on FastEthernet1/0 from LOADING to FULL, Loading Done

Router(config-router)#exit