模具专业英文术语大全 This model paper was revised by the Standardization Office on December 10, 2020
模具英语专业术语
模具述语
一、入水:gate
进入位: gate location
水口形式:gate type
大水口:edge gate
细水口: pin-point gate
水口大小:gate size
转水口: switching runner/gate 唧嘴口径: sprue diameter
二、流道: runner
热流道: hot runner,hot manifold
热嘴冷流道: hot sprue/cold runner
唧嘴直流: direct sprue gate 圆形流道:round(full/half runner
流道电脑分析:mold flow analysis
流道平衡:runner balance
热嘴: hot sprue
热流道板:hot manifold
发热管:cartridge heater 探针: thermocouples
插头: connector plug
插座: connector socket
密封/封料: seal
三、运水:water line
喉塞:line lpug
喉管:tube
塑胶管:plastic tube
快速接头:jiffy quick connector plug/socker
四、模具零件: mold components 三板模:3-plate mold
二板模:2-plate mold
边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing
中托司:shoulder guide bushing 中托边L:guide pin
顶针板:ejector retainner plate 托板: support plate
螺丝: screw
管钉:dowel pin 开模槽:ply bar scot
内模管位:core/cavity inter-lock
顶针: ejector pin
司筒:ejector sleeve
司筒针:ejector pin
推板:stripper plate
缩呵:movable core,return core core puller
扣机(尼龙拉勾):nylon latch lock
斜顶:lifter
模胚(架): mold base
上内模:cavity insert
下内模:core insert
行位(滑块): slide
镶件:insert
压座/斜鸡:wedge
耐磨板/油板:wedge wear plate 压条:plate
撑头: support pillar
唧嘴: sprue bushing
挡板:stop plate
定位圈:locating ring
锁扣:latch
扣鸡:parting lock set
推杆:push bar
栓打螺丝:顶板:eracuretun
活动臂:lever arm
分流锥:spure sperader
水口司:bush 垃圾钉:stop pin
隔片:buffle
弹弓柱:spring rod
弹弓:die spring
中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin
销子:dowel pin
波子弹弓:ball catch
喉塞: pipe plug
锁模块:lock plate
斜顶:angle from pin
斜顶杆:angle ejector rod 尼龙拉勾:parting locks
活动臂:lever arm
复位键、提前回杆:early return bar
气阀:valves
斜导边:angle pin
术语:terms
承压平面平衡:parting surface support balance
模排气:parting line venting
回针碰料位:return pin and cavity interference
模总高超出啤机规格:mold base shut hight
顶针碰运水:water line interferes withejector pin
料位出上/下模:part from cavith (core) side 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate.
不准用镶件: Do not use
(core/cavity) insert
用铍铜做镶件: use beryllium copper insert
初步(正式)模图设计:preliinary (final) mold design 反呵:reverse core
弹弓压缩量:spring compressed length
稳定性好:good stability,stable 强度不够:insufficient rigidity 均匀冷却:even cooling
扣模:sticking
热膨胀:thero expansion
公差:tolorance
铜公(电极):copper electrode Mold & die components 模具单元Mold changing systems 换模系统Mold core 模芯
Mold heaters/chillers 模具加热器/冷却器
Mold polishing/texturing 模具打磨/磨纹
Mold repair 模具维修
Molds 模具
Pressing dies 压模
Quick die change systems 速换模系统Quick mold change systems 快速换模系统
三、模具
塑料模具 mould of plastics
注塑模具injection mould
冲压模具die
模架mould base
定模座板Top clamping plate Top plate
Fixed clamp plate
水口推板stripper plate
A 板A plate
B 板B plate
支承板 support plate
方铁 spacer plate
底针板 ejector plate
面针板 ejector retainer plate 回针 Return pin
导柱 Guide pin
有托导套 Shoulder Guide bush
直导套 Straight Guide bush
动模座板Bottom clamp plate Moving clamp plate
基准线datum line
基准面datum plan
型芯固定板core-retainer plate 凸模固定板punch-retainer plate 顶针ejector pin
单腔模具single cavity mould
多腔模具multi-cavity mould 多浇口multi-gating
浇口gate
缺料starving
排气breathing
光泽gloss
合模力mould clamping force 锁模力mould locking force 挤出extrusion
开裂crack
循环时间cycle time
老化aging
螺杆screw
麻点pit
嵌件insert
活动镶件movable insert
起垩chalking
浇注系统feed system
主流道 sprue
分流道runner
浇口gate
直浇口direct gate , sprue gate 轮辐浇口spoke gate , spider gate
点浇口pin-point gate
测浇口edge gate
潜伏浇口submarine gate , tunnel gate
料穴cold-slug well
浇口套sprue bush
流道板runner plate 排飞槽vent
分型线(面)parting line
定模stationary mould,Fixed mould
动模movable mould, movable half 上模upper mould, upper half
下模lower mould, lower half
型腔cavity
凹模cavity plate,cavity block 拼块split
定位销dowel
定位销孔dowel hole
型芯core
斜销angle pin, finger cam
滑块slide
滑块导板slide guide strip
楔紧块heel block, wedge lock 拉料杆sprue puller
定位环locating ring
冷却通cooling channel
脱模斜度draft
滑动型芯slide core
螺纹型芯threaded core
热流道模具hot-runner mould
绝热流道模insulated runner mould
熔合纹weld line (flow line)三板式模具 three plate mould 脱模ejection 换模腔模具 interchangeable cavity mould
脱模剂release agent
注射能力shot capacity
注射速率injection rate
注射压力injection pressure
差色剂colorant
保压时间holdup time
闭模时间closing time
定型装置sizing system
阴模female mould,cavity block 阳模male mould
电加工设备Electron Discharge Machining
数控加工中心CNC machine center
万能铁床Universal milling machine
卧式刨床Horizontal planer
车床Engine lathe
平面磨床Surface grinding machine
去磁机Demagnetization machine
万能摇臂钻床Universal radial movable driller
立式钻床Vertical driller
超声波清洗机Ultrasonic clearing machine
compre sion molding 压缩成型flash mold 溢流式模具
plsitive mold 挤压式模具
split mold 分割式模具cavity 型控母模
core 模心公模
taper 锥拔
leather cloak 仿皮革
shiver 饰纹
flow mark 流痕
welding mark 溶合痕
post screw insert 螺纹套筒埋值self tapping screw 自攻螺丝striper plate 脱料板
piston 活塞
cylinder 汽缸套
chip 细碎物
handle mold 手持式模具
(移转成型用模具)
encapsulation molding 低压封装成型
(射出成型用模具)
two plate 两极式(模具)
well type 蓄料井
insulated runner 绝缘浇道方式hot runner 热浇道
runner plat 浇道模块
valve gate 阀门浇口
band heater 环带状的电热器spindle 阀针
spear head 刨尖头
slag well 冷料井
cold slag 冷料渣
air vent 排气道welding line 熔合痕
eject pin 顶出针
knock pin 顶出销
return pin 回位销反顶针
sleave 套筒
stripper plate 脱料板
insert core 放置入子
runner stripper plate 浇道脱料板
guide pin 导销
eject rod (bar)(成型机)顶业捧subzero 深冷处理
three plate 三极式模具
runner system 浇道系统
stress crack 应力电裂
orientation 定向
sprue gate 射料浇口,直浇口nozzle 射嘴
sprue lock pin 料头钩销(拉料杆) slag well 冷料井
side gate 侧浇口
edge gate 侧缘浇口
tab gate 搭接浇口
film gate 薄膜浇口
flash gate 闸门浇口
slit gate 缝隙浇口
fan gate 扇形浇口
dish gate 因盘形浇口
diaphragm gate 隔膜浇口
ring gate 环形浇口subarine gate 潜入式浇口tunnel gate 隧道式浇口pin gate 针点浇口Runner less 无浇道(sprue less)无射料管方式long nozzle 延长喷嘴方式sprue 浇口;溶渣
emboss 凸点
dome 凸圆
semi-shearing 半剪stamp mark 冲记号
deburr or coin 压毛边punch riveting 冲压铆合side stretch 侧冲压平reel stretch 卷圆压平
groove 压线
blanking 下料
stamp letter 冲字(料号) shearing 剪断
tick-mark nearside 正面压印tick-mark farside 反面压印冲压名称类
extension dwg 展开图procedure dwg 工程图
die structure dwg 模具结构图material 材质
material thickness 料片厚度factor 系数
upward 向上
downward 向下press specification 冲床规格die height range 适用模高
die height 闭模高度
burr 毛边
gap 间隙
weight 重量
total wt.总重量
punch wt.上模重量
五金零件类
inner guiding post 内导柱inner hexagon screw 内六角螺钉dowel pin 固定销
coil spring 弹簧
lifter pin 顶料销
eq-height sleeves=spool 等高套筒
pin 销
lifter guide pin 浮升导料销guide pin 导正销
wire spring 圆线弹簧
outer guiding post 外导柱
stop screw 止付螺丝
located pin 定位销
outer bush 外导套
模板类
top plate 上托板(顶板)
top block 上垫脚
punch set 上模座
punch pad 上垫板punch holder 上夹板
stripper pad 脱料背板
up stripper 上脱料板
male die 公模(凸模)
feature die 公母模
female die 母模(凹模)
upper plate 上模板
lower plate 下模板
die pad 下垫板
die holder 下夹板
die set 下模座
bottom block 下垫脚
bottom plate 下托板(底板) stripping plate 内外打(脱料板) outer stripper 外脱料板
inner stripper 内脱料板lower stripper 下脱料板
零件类
punch 冲头
insert 入块(嵌入件) deburring punch 压毛边冲子groove punch 压线冲子stamped punch 字模冲子
round punch 圆冲子
special shape punch 异形冲子bending block 折刀
roller 滚轴baffle plate 挡块
located block 定位块
supporting block for location 定位支承块
air cushion plate 气垫板
air-cushion eject-rod 气垫顶杆trimming punch 切边冲子stiffening rib punch = stinger 加强筋冲子
ribbon punch 压筋冲子
reel-stretch punch 卷圆压平冲子guide plate 定位板
sliding block 滑块
塑料模具专业术语
动模 movable mould moving half
定模座板 fixed clamp plate, top clamping plate. top plate 动模座板 moving clamp plate. bottom clamping plate. bottom plate
上模座板 upper clamping plate
下模座板 lower clamping plate
凹模固定板 cavity-retainer plate
型芯固定板 core-retainer plate
凸模固定板 punch-retainer plate
模套 chase. bolster. frame 支承板 backing plate. supprr plate
垫块 spacer parallel
支架 ejector housing. mould base leg
压力铸造模具 die-casting die 压铸模零部件
定模 fixed die, cover die
定模座板 fixed clamping
plate
定模套板 bolstor, fixed die 动模 moving die,ejector die 动模座板 moving clamping plate
直流道 sprue
横流道 runner
内浇口 gate
landed plunger mold||有肩柱塞式模具
burnishing die||挤光模
landed positive mold||有肩全压式模具
button die||镶入式圆形凹模loading shoe mold||料套式模具center-gated mold||中心浇口式模具
loose detail mold||活零件模具chill mold||冷硬用铸模
loose mold||活动式模具
clod hobbing||冷挤压制模louvering die||百叶窗冲切模composite dies||复合模具manifold die||分歧管模具counter punch||反凸模
modular mold||组合式模具double stack mold||双层模具multi-cavity mold||多模穴模具electroformed mold||电铸成形模multi-gate mold||复式浇口模具expander die||扩径模
offswt bending die||双折冷弯模具
extrusion die||挤出模palletizing die||叠层模
family mold||反套制品模具plaster mold||石膏模
blank through dies||漏件式落料模
porous mold||通气性模具duplicated cavity plate||复板模positive mold||全压式模具fantail die||扇尾形模具pressure die||压紧模
fishtail die||鱼尾形模具
profile die||轮廓模
flash mold||溢料式模具progressive die||顺序模
gypsum mold||石膏铸模
protable mold||手提式模具
hot-runner mold||热流道模具prototype mold||雏形试验模具ingot mold||钢锭模
punching die||落料模
lancing die||切口模
raising(embossing)||压花起伏成形
re-entrant mold||倒角式模具sectional die||拼合模
runless injection mold||无流道冷料模具
sectional die||对合模具segment mold||组合模
semi-positive mold||半全压式模具
shaper||定型模套
single cavity mold||单腔模具solid forging die||整体锻模
模具英语专业术语 模具述语 一、入水:gate 进入位: gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口: switching runner/gate 唧嘴口径: sprue diameter 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴: hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头: connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件: mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板: support plate 螺丝: screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针: ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug
塑胶模具类中英文对照专业术语工程部/ Design department: 1) Designer - 设计师。 2) Assembly drawing - 模具组装图。 3) Mold layout - 模具结构图。 4) 2D product drawing - 2D产品图。 5) 3D product data - 3D产品数据。 6) Part drawing - 散件图。 7) Insert molding - 镶件模。 8) 2 color mold / Double injection tool - 双色模。 9) Hydraulic system - 油/水压系统。 10) Parting line - 分模线。 11) Air venting - 排气槽。 12) Cooling system - 冷却系统。 13) Screw - 镙丝。 14) Hot runner system - 热流道。 15) Valve gate - 伐针入水口。 16) Fan gate - 扇型入水口。 17) Pin point gate - 针点进胶。 18) Moon gate / Banana gate - 香蕉,象牙入水口。 19) Submarine gate - 潜水口。 20) Injection machine tonnage - 注塑机吨数。 21) Number of cavity - 穴数。 22) Steel - 钢材。 23) Copper - 铜。 24) Tungsten copper - 钨铜。 25) Beryllium copper - 铍铜。 26) Hardening - 加硬/淬火。 27) Tempering - 回火。
模芯 Parting Core 耐落胶 Teflon Paste 局部视图 Partial View 偏移量 Offset 冷料 Cold Slag 水塞 Water Line Plug 线切割 Wire 撬模脚 Ppy Slot 轮廓 Contour 重新加工 Reworked 螺纹孔Tapping Hole 配件 Components 连接件 Fittings 补偿 Compensation 斜针 Angle Pin 平面度 Parallel 接合 Engage 倒角Chamfer 替换镶件Interchangeable Mold Inserts 模胚 Mold Base 指定吨位的注塑机 Specific Press 热嘴Hotnozzle 水嘴接头 Water Fitting 火花机 Edm 螺纹 Eyebolt Thread 熔接线 Weildline 回针 Stop Pin 压机 Press 二级顶出针 Sub-Leaderd Pin 嗮纹 Texturing 镶件 Mold Insert 梯形 Trapezoid
加硬 Harden 凸缘、法兰 Flange 唧嘴 Sprue 方铁 Spacer Block 设计筒图 Design Preliminary 顶针板 Ejector Plate 名称块表 Title Block 顶针底板 Ejector Retainer Plate 版本标识 Revision Level 垫板 Retainer Plate 材料清单 Stock List 后模镶针 Core Pin 制模 Build Mold 垃圾钉 Stop Pin 手动滑块 Hand Slide 有托顶针 Shoulder Ejector Pin 漏水测试 Leak Test 顶针板导套Guided Ejection Bushing 流道排气 Runner Vents 针板导柱 Guided Ejection Leader Pin 抛光 Draw Polish 唧嘴 Sprue Bushing 侧抽芯 Slide Action 三板模延伸式唧嘴 Extension Noozzle Bulishing 加强筋 Reinforcing 水口板导套 Runner Stripper Pin 三角撑 Gusset 定位圈(法兰)Locating Ring 柱子 Bossed 管钉(定位销)Dowel Pin 出模斜度 Draft 管状管钉 Tubular Dowel
实用文案 模具英语专业术语 模具述语开模槽:ply bar scot 内模管位:一、入水:gate core/cavity inter-lock 顶针:ejector pin 进入位:gate location 司筒:ejector sleeve 水口形式:gate type 司筒针:edge gate ejector pin 大水口:推板:细水口:stripper plate pin-point gate 缩呵:gate size movable core,return core core 水口大小:puller switching runner/gate 转水口:扣机(尼龙拉勾):nylon latch lock sprue diameter 唧嘴口径:斜顶:lifter : runner 二、流道模胚(架):mold base hot runner,hot manifold 热流道:上内模:cavity insert : hot sprue/cold runner 热嘴冷流道下内模:core insert : direct sprue gate 唧嘴直流行位(滑块):slide round(full/half runner 圆形流道:镶件:insert mold flow analysis 流道电脑分析:压座/斜鸡:wedge :runner balance 流道平衡耐磨板/油板:wedge wear plate hot sprue 热嘴:压条:plate hot manifold 热流道板:撑头: support pillar cartridge heater 发热管:唧嘴:sprue bushing : thermocouples 探针挡板:stop plate connector plug 插头:定位圈:locating ring connector socket 插座:锁扣:latch seal 封料:/密封扣鸡:parting lock set water line 三、运水:推杆:push bar line lpug 喉塞:栓打螺丝:S.H.S.B tube 喉管:顶板:eracuretun plastic tube 塑胶管:活动臂:lever arm jiffy quick connector 快速接头:分流锥:spure sperader plug/socker 水口司mold components 四、模具零件::bush 垃圾钉:三板模:3-plate mold stop pin 隔片:buffle 二板模:2-plate mold 弹弓柱:导边:/leader pin/guide pin spring rod 边钉弹弓:die spring 导套:边司/bushing/guide bushing 中托司:ejector guide bush 中托司:shoulder guide bushing 中托边:ejector guide pin guide pin :L中托边镶针:ejector retainner plate 顶针板:pin 销子:托板:support plate dowel pin 波子弹弓:ball catch screw 螺丝:: pipe plug dowel pin 管钉:喉塞文案大全. 实用文案 锁模块:lock plate Mold repair 模具维修 angle from pin 斜顶:Molds 模具
模具术语英文翻译
模具术语英文翻译 根据国家标准,以下为部分塑料模具成形术语的标准翻译。 动模 Movable Mould Moving Half 定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate 动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate 下模座板 Lower Clamping Plate 凹模固定板 Cavity-retainer Plate 型芯固定板 Mould Core-retainer Plate 凸模固定板 Punch-retainer Plate 模套 Die Body Die Sleeve Die Blank 支承板 Backing Plate Support Plate 垫块 Spacer Parallel 支架 Ejector Housing Mould Base Leg 模头 Die Head 根据国家标准,以下为部分压铸模具术语的标准翻译。 压力铸造模具 Die-Casting Die 压铸模零部件 定模 Fixed Die Cover Die 定模座板 Fixed Clamping Plate 定模套板 Bolster Fixed Die 动模 Moving Die Ejector Die 动模座板 Moving Clamping Plate 直流道 Sprue 横流道 Runner 内浇口 Gate 模具分类 Injection Mold 注塑模 Plastic Rubber Mould 塑胶模 Rubber Molding 橡胶成形 Hot Chamber Die Casting 热室压铸 Sand Mold Casting 砂模铸造 Extrusion Mold 挤出模 Multi-Cavity Mold 多模穴模具 Stack Mold, Stack Injection Mould 叠层模
常用模具零件中英文对照表 2005-12-19 14:51:17???中国注塑网 入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口: pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis :?[??n?l?s?s] 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边:guide pin 顶针板:ejector retainer plate 托板:support plate
"R,L Co.,Ltd" 模具常用术语中英文对照 模芯Parting Core 局部视图Partial View 冷料# Cold Slag 线切割 Wire 轮廊Contour 螺纹孔 Tapping Hole 连接件 Fittings 斜针Angle Pin 接合Engage 替换镶件Interchangeable Mold Inserts 指定吨位的注塑机Specific Press 水嘴接头Water Fittings 螺纹Eyebolt Thread 回针Stop Pin 二级顶出针Sub-Leaderd Pin 镶件Mold Insert 加硬Harden 唧嘴Sprue 设计筒图Design Preliminary 名称块表Title Block 版本标识Revision Level 材料清单Stock List 制模Build Mold 手动滑块Hand Slide 漏水测试Leak Test 流道排气Runner Vents 抛光Draw Polish 侧抽芯 Side Action 加强筋 Reinforcing
三角撑 Gusset 柱子Bossed 出模斜度Draft 外廊Contour 落单会议Kick-Off Meeting 装卸孔 Handling Hole 运输安全带Moldstrap 码模槽 Clamp Slot 撑头Support Pillar 螺牙1/2-13 Eye Bolt 1/2-13Tap 导柱位 Leader Pin Location 耐落胶 Teflon Paste 偏移量 Offset 水塞Water Line Plug 撬模脚 Ppy Slot 重新加工Reworked 配件Components 补偿Compensation 平面度 Parallel 倒角Chamfer 模胚Mold Base 热嘴Hotnozzle 火花机 Edm 熔接线 Weildline 压机Press 晒纹Texturing 梯形Trapezoid 凸缘、法兰Flange 方铁Spacer Block 顶针板Ejector Plate 顶针底板Ejector Retainer Plate 垫板Retainer Plate
模具英语专业术语模具的分类: 冲压模(五金模): stamping die 分离模: cutting die 成形模: forming die 塑胶模: plastics mold 注射模: injection mold 压缩模: compression mold 铸塑模: transfer mold 吹塑模: blow mold 吸塑模: suck mold 铸造模: casting die 砂型铸造: sand casting 压铸模: die casting 锻造模: forging die 塑胶模具术语 一、入水:gate 进入位(入水点):gate location 水口形式:gate type 大水口(侧浇口): edge gate 潜水口: sub-gate 薄膜式水口: film gate 牛角式潜水口: banana gate 扇形水口: fan gate 环形水口: ring gate 二次水口: 细水口:pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 直接水口: direct gate 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道:round(full/half) runner 矩形流道: rectangle runner 梯形流道: trapezoid runner U形流道: U shape runner 流道电脑分析(模流分析):mold flow analysis 流道平衡: runner balance
模具专业英文术语大全
模具英语专业术语 模具述语 一、入水:gate 进入位:gate location 水口形式:gate type 大水口:edge gate 细水口:pin-point gate 水口大小:gate size 转水口:switching runner/gate 唧嘴口径:sprue diameter 二、流道: runner 热流道:hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道:round(full/half runner 流道电脑分析:mold flow analysis 流道平衡:runner balance 热嘴:hot sprue 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座:connector socket 密封/封料:seal 三、运水:water line 喉塞:line lpug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socker 四、模具零件:mold components 三板模:3-plate mold 二板模:2-plate mold 边钉/导边:leader pin/guide pin 边司/导套:bushing/guide bushing 中托司:shoulder guide bushing 中托边L:guide pin 顶针板:ejector retainner plate 托板:support plate 螺丝:screw 管钉:dowel pin 开模槽:ply bar scot 内模管位:core/cavity inter-lock 顶针:ejector pin 司筒:ejector sleeve 司筒针:ejector pin 推板:stripper plate 缩呵:movable core,return core core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架):mold base 上内模:cavity insert 下内模:core insert 行位(滑块):slide 镶件:insert 压座/斜鸡:wedge 耐磨板/油板:wedge wear plate 压条:plate 撑头: support pillar 唧嘴:sprue bushing 挡板:stop plate 定位圈:locating ring 锁扣:latch 扣鸡:parting lock set 推杆:push bar 栓打螺丝:S.H.S.B 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 中托司:ejector guide bush 中托边:ejector guide pin 镶针:pin 销子:dowel pin 波子弹弓:ball catch 喉塞: pipe plug 锁模块:lock plate 斜顶:angle from pin
模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin
32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机(尼龙拉勾)n yl on latch lock 45斜顶lifter 46模胚(架)mold base 47母模cavity in sert 48公模core insert 49行位(滑块)slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm
钣金设计中常用的其它术语 扩孔enlarge hole 自铆self-chinching 全周压毛边all round burr 平头拉钉set-head rivet 表面处理finish 定位销dowel pin 挂钩hook 平头铆钉closed-end rivet 焊接线weld line 塑料固定栓fastener, plastic, push-type 压合胶粘剂pressure sensitive adhesive 尼龙绑带tie wrap, nylon 五金件hardware 泡棉静电导片gasket, foam, emi 贴纸labeling 铍铜静电导片gasket, beck, emi 烤漆paint 圆头螺钉button-head screw 电镀plating 平头螺母nut flush 铭板nameplate 平齐自铆flush, self-clinching 包装packing 紧固螺丝fix screw 铁材零件sheet metal parts 组装assembly 塑料零件plastic parts 凹陷,顶针sink mark 压边铆钉open-end rivet 插孔jack 弹簧螺丝caps 度thick 文字,记号char actor 半冲孔spring slice 角corner 基座chassis 自锁螺母nut self-clenching 承座bracket 轴肘式铆接toggle lock 承架horsing 卡尺caliper 下盖base 打印字模stamp letter 去毛边deburr 推板导住ejector guide 直导套guide bush, straight[straight bushing] 带头导套guide bush, straight {shoulder bushing} 推板导套ejector guide bush[ejector bushing] 定位圈Locating ring 锥形定位件mould bases locating elements 复位杆ejector plate return pin[push-back pin] 限位钉stop pin[stop but ton] 限位块stop block [stop pad] 定距拉杆puller[length]bolt 定距拉板puller[limit]plate 成形推杆forming ejector pin 圆柱头推杆ejector pin with cylindrical head 带肩推杆shouldered ejector pin 扁推杆flat ejector pin 推管ejector sleeve 推块ejector pad 推件板stripper plate 推杆固定板ejector retainer plate ; 推板ejection plate[elector plate] 连接推杆ejector tie rod 冲裁间隙blanking clearance 模具闭合高度die shut height 压力机闭合高度shut height Of press machine 冲模寿命die life 压力中心center Of load 冲模中心center Of die 冲压方向pressing direction 送料方向feed direction 排样blank layout 搭边scrap 进距feed pitch 切边余量trimming allowance 毛刺burr 冲裁力blanking force 弯曲力bending force 拉仲力drawing force 挤压力extruding force 卸料力stripping force 推件力ejecting force 顶件力kicking force 压料力pressure plate force 压边力black holder force 毛坯blank ;
1.XXX!你现在有空吗,我可以问你一些问题吗? Could I ask you some questions if you are free?/ Are you free now? May I ask you some questions (a question)? 2.请问此产品的面是否为外观面?表面做什么处理?是晒纹/抛光? Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3.请问产品这个面可否加顶针或顶块?产品允许加扁顶针吗? Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4.这个产品的柱位我们打算做司筒。(或镶针)可以吗? Can we add ejector sleeves or ejector pins in the boss of this part? 5.产品的这个位置不能出模,我们打算做行位,在此面上会有分模线,你接受吗? There's an undercut at this position and it needs a slider. It will also have a parting line on this side, is that OK? 6.产品里面的这个位置我们打算做斜顶或内行位,有问题吗? We will make the lifter and (inner) slider in this position, will that be a problem? 7.你提供的2D产品图与3D产品图不一致,请问以哪一个图面为准? The 2D and 3D drawing you provided is not the same, can you tell me which one is correct? 8.你提供的3D产品图有的地方没有出模角,有的地方胶位太厚,有的地方胶位太溥,这些产品问题我们可以自己修改吗?修改后会给交给你确认。 There is no draft angle in the 3D drawing, some materials are too thick, and some place are too thin. Can we modify this part by ourselves? We will send the drawing to you for you to check after we modify it. 9.按你们提供的缩水率千分之五,这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确? Accoring to the shrinkage one over two hundred, the mold has been done in the right dimension, but the part falls short to your part drawing, are you sure the shrinkage is right? 10.产品的这个位置太小,导致模具钢料太溥,能够加宽这个位置吗? This position is too small and will make the steel material here too thin, can we widen it here? 11.斜顶与后面的柱位空间太小,斜顶在运动时会干涉到柱子,能移动这个柱子的位置吗?The angular lifter interferes with the boss during ejection. Please consider changing the position of the boss. 12.这个筋骨位胶厚太溥,而且高度偏高,注塑时很难填充这个筋位,可以增加这个筋骨位的厚度吗? The rib here is too thin and on the high side, so it will be difficult to fill here when we do the injection, can you inrcease the thickness of this rib? 13.你是想将此筋骨位的高度加高/减低吗?加胶的位置我们将用铜公放电加深。但减胶的位置有两种做法,1、做镶件;2、烧焊;因为镶件的底部有运水,我们简单的做法是烧焊处理,你可以接受吗? Will you increase/decrease the material on this rib? We will use EDM if you add material, but there are two option if you choose to decrease:1.Make inserts;2.Welding, because there is water in the bottom of the insert, is that OK? 14.这个样板的筋骨位底部烧焦,是因为排气不良,我们可以在筋骨位的中间增加一个镶件。This sample has been burned in the bottom because the venting is not good, we can add an insert in the middle of the rib.
模具用语中英文对照 198各式模具分类用语中英文对照 landed plunger mold 有肩柱塞式模具 burnishing die 挤光模Www_17He_com landed positive mold 有肩全压式模具 button die 镶入式圆形凹模一起呵_英语站loading shoe mold 料套式模具center-gated mold 中心浇口式模具一起呵@英语站loose detail mold 活零件模具 chill mold 冷硬用铸模 loose mold 活动式模具 clod hobbing 冷挤压制模一起呵@英语站louvering die 百叶窗冲切模 composite dies 复合模具英.语.站 manifold die 分歧管模具一起呵_英语站counter punch 反凸模英语.站 modular mold 组合式模具 double stack mold 双层模具17He~Com multi-cavity mold 多模穴模具 electroformed mold 电铸成形模 multi-gate mold 复式浇口模具 expander die 扩径模一起呵.英语.站offswt bending die 双折冷弯模具
extrusion die 挤出模英语.站 palletizing die 叠层模一起呵@英语@站family mold 反套制品模具一.起.呵.英语站plaster mold 石膏模 17he_com blank through dies 漏件式落料模一porous mold 通气性模具duplicated cavity plate 复板模一起呵@英语站positive mold 全压式模具 fantail die 扇尾形模具 17he_com pressure die 压ingot mold 钢锭模 punching die 落料模 lancing die 切口模英语.站 raising(embossing) 压花起伏成形 re-entrant mold 倒角式模具 sectional die 拼合模 runless injection mold 无流道冷料模具一起呵_英语站 sectional die 对合模具 英.语.站 segment mold 组合模一起_呵_英语站 semi-positive mold 半全压式模具一起_呵_英语站 shaper 定型模套 single cavity mold 单腔模具
冲压模具词汇Counter bored hole沉孔 Chamfer倒斜角 Fillet倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count复盘人 second check复盘复核人
equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count复盘点数量 Quantity of customs count会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills年终盘点截止单据汇总表 bill name单据名称 Thissheetandphysicalinventorylistwillbesenttoaccountingdepartmenttogether(T hoseofNHKwillbesenttofinancialdepartment) 本表请与盘点清册一起送会计部-(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card年终盘点卡与清册使用-状况明细表blank and waste sheet NO.空白与作废单号 plate电镀 mold成型 material for engineering mold testing工程试模材料 not included in physical inventory不列入盘点 sample样品
五金模具常用专业术语中英文对照表 上模座 upper die set 成型公 form punch 脱料板 stripper 垫板 subplate/backup plate 下模座 die plate 滑块 CAM slider 垫脚 parallel 误检 misfeeder 托板 mounting plate 顶料销 kick off 初始管位 first start pin 带肩螺丝 shoulder screw 两用销 lifter pin 氮气汽缸 gas spring 弹簧护套 spring cage 拔牙螺丝 jack screw 侧冲组件 cam section 导正装置 guide equipment 漏废料孔 slug hole 刀口 trim line 加强装置 enhance equipment 入子 insert 护套 bushing 整形公 restrike forming punch 止挡板 stop plate 挂台 head 扣位 pocket of head 导柱 guide post 导套 guide bushing 油嘴 oil nipple 接刀口 mismatch/cookie bites 限位块 stop block 挡块 stopper 浮块 lifter 压块 keeper 靠块 heel 对正块 alignment block 简易模 prototype tooling 检具 gage/checking fixture 料带图 strip layout 闭合高度 shut hight 俯视图 top view 料带 strip 公差 tolerance 正视图 front view 走位 travel 避位/空 pocket 退磁 demagnetization 间隙 clearance 真空热外理 vacuum heat treatment 镗孔 mill hole 表面外理 surface coasting 镀钛 TD coasting 沉头 counter sink 精锣 finish mill 线割 wire cutting 穿丝孔 first wire hole 斜度 taper 镭射laser-cut 上夹板/固定座 holder/retainer 下模座 lower die set 成刑母公 forming die 电火花 EDM 码模槽 mounting slot 球锁紧固定座 ball-lock 导尺 rail 球锁紧凸模 BALL--LOCK 送料板 rail plate 外购 out sourcing 倒角 chamfer 清角 SCRAP CHOPPER 销钉 dowel 尖角 sharp --angle 普通弹簧 coil spring