当前位置：搜档网 › 轮机英语Ⅲ-轮机英语Ⅲ试卷

轮机英语Ⅲ-轮机英语Ⅲ试卷

Direction: This part is to test your ability to translate English into Chinese.

1.The bedplate, frames and cylinder blocks are secured together by long tie-rods to

achieve a greater rigid construction with less deformation in service and lower vibration. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 2.The by-pass line with overflow valve between the inlet and outlet of the main

engine serves the purpose of by-passing the main engine if, for instance, a major overhaul is required on the main engine fuel oil system. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 3. In addition to providing lubricating films, oils used in marine diesel engines have

to remove heat from oil cooled pistons, neutralize acidic products of combustion, cleanse hot moving parts of carbonaceous deposits, resist oxidation and wash away wear detritus. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 4. By increasing the density of the charge air by the use of a suitable compressor

between the air intake and the cylinder, the weight of air induced per working stroke is increased, and thereby a greater weight of fuel can be burnt, with a consequent increase in the cylinder power output. (10’)

5. Lip seas are shaped rings of material with a projecting lip or edge which is held in

contact with a shaft to prevent oil leakage or water entry. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 6. The auxiliary steam installation provided in modern diesel powered tankers

usually uses all exhaust gas heat exchanger at the base of the funnel and one or perhaps tow water tube boilers. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 7. Also it must be continued for at least two hours after the engine has been stopped

to ensure that any combustible material from the exhaust gas which has deposited on the heating surfaces is thoroughly cooled below the ignition point. (10’)

__________________________________________________________________ __________________________________________________________________ __________________________________________________________________ 8. Sea training is done when the Marine Engineer has accumulated sufficient

knowledge to enable him to go to sea on an ocean. This is the time when he can live the life of a seaman. The Cadet Marine Engineer receives his uniform as an officer. He usually undergoes his apprenticeship under the 2nd Engineer, who will assign him duties. Because various engineers have specific duties and responsibilities, the cadet engineer may be assigned to help other engineers during his tour of duty on board ship. The sea training can be anything from 6 months to 1 year, depending on the College he attends, and the requirement of the various Countries’ Governments which issue out Marine Certificates of Competency. (30’)

三管轮轮机英语大证考试真题41期

中华人民共和国海事局 2006年第3期海船船员适任证书全国统考试题(总第41期) 科目：轮机英语试卷代号：805 适用对象：无限、近洋航区3000KW及以上船舶二/三管轮（本试卷卷面总分100分，及格分为70分，考试时间为100分钟）答题说明：请选择一个最合适的答案，并将该答案按答题卡要求，在其相应位置上用2B铅笔涂黑。第1题至74题，每题1分，第75题至78题，每题1.5分,第79题至80题, 每题10分。一、单项选择题 1. A diesel engine is similar to a gasoline engine except that the former has no ______. A. cross-head B. spark plug C. connecting rod D. cylinder 2. A diesel engine which is rated for normal operation at a crankshaft speed of 800 RPM, is commonly classed as a ______. A. slow-speed diesel B. medium-speed diesel C. high-speed diesel D. constant-speed diesel 3.Which of the diesel engine components listed increases air density and helps to improve engine operating efficiency? A. Impeller B. Compressor C. After-cooler D. Exhaust diffuser 4.For a given size engine, the two-stroke/cycle diesel engine will deliver more power than a four- stroke/cycle diesel engine because ______. A. it has a longer power stroke B. more air gets into the cylinder each stroke C. it develops twice as many power strokes at the same speed D. higher combustion pressure is developed 5.The intake valves in a diesel engine are reseated by ______. A. cam followers B. push rods C. combustion gases D. valve springs 6.According to the way the energy of the exhaust gases is utilized, pressure-charging can be divided into two main systems, namely, the constant-pressure system and ______. A. the pulse-phase system B. the pulse Doppler system C. the pulse system D. the pulse interval system 7.An over-speed safety device is usually fitted to a generator engine for______in the event of over- speed. A. cutting power off the engine B. increasing the fuel pump setting C. braking the crankshaft D. stabilizing the ship speed 8.What preventative maintenance should be done frequently to diesel engine starting air receivers? A. Drain the accumulated moisture. B. Test the relief valves. C. Watch the temperature to prevent fluctuations in pressure. D. Clean the interior to remove oil and foreign matter. 9.Immediately after any diesel engine is started, the engineer should check the ______. A. crankcase pressure B. lube oil pressure C. seawater pressure D. exhaust temperature 10. A controllable pitch propeller on a diesel driven vessel eliminates the need for ______. A. friction clutches B. disconnect clutches C. reversing gears D. reduction gears 11.In motor ship, ______is often used to recover some of the heat carried in the exhaust gases from the main engine. A. an diesel oil heater B. a waste heat boiler C. a fresh water generator D. a donkey boiler 12.An exhaust gas bypass is installed on a waste heat boiler in order to ______. A. bypass exhaust gas at high loads to prevent excessive back pressure B. bypass a portion of the exhaust gas at peak loads for better efficiency C. recycle exhaust gas to the turbocharger D. minimize moisture condensation in the boiler gas passages at low loads 13.Prior to lighting off a cold automatically fired auxiliary boiler, you should ______. A. check and regulate the water level B. close the air cock once fires are lit C. blow down the gage glass D. assure protective steam flow 14.Flame failure in an automatically fired auxiliary boiler can mostly result from a/an ______. A. incorrect electrode setting B. incorrect nozzle position C. clogged fuel nozzle D. broken high tension lead 15.Waterside scale in a fire-tube boiler may cause ______. A. increased heat transfer B. fireside erosion C. high steam demand D. overheated tubes 16.Which of the following will be the advantage of a centrifugal pump as compared with a reciprocating pump? I. Its discharge is continuous; II. It has no internal valves; III. Upon accidental closing of discharge valve, excessive pressure will not build up A. I, II B. II, III C. I, II, III D. II only 17.Why are removable sleeves installed on centrifugal pump shafts? A. They make it easier to replace the pump shaft packing. B. They can be economically replaced as they wear out. C. They can be removed when it is necessary to lighten the weight of the pump. D. They increase the strength of the shaft. 18.If one of the bilge system manifold valves does not properly seat, the ______. A. bilge well connected to that valve, plus the second bilge well being pumped will be completely emptied B. bilge system will lose vacuum and prevent the other bilges from being pumped out C. bilge well aft connected to that valve will siphon(虹吸) its contents to the forward bilge wells D. discharge pressure will be too high. 19.Which of the listed statements is correct concerning the starting of centrifugal pumps? A. They should always be started with the discharge valve closed. B. They should always be started with the discharge valve opened. C. A priming pump is always required to flood the impeller suction. D. They should always be started with the sealing line valves closed. 20.The simplest method to use for determining if a centrifugal pump is operating as designed, is to ______. A. closely observe the pump discharge temperature B. close off the discharge valve, and watch for a rise in pressure C. momentarily close off the suction valve, and watch for a rise in pressure D. use a clamp on ammeter and compare the readings to past records

2020年自考英语模拟试题及答案

2020年自考英语模拟试题及答案一、语音知识(5 points) 第1题请选择出划线部分读音不同的选项( )。 A.practice B.possible C.physical D.pacific 答案：B 第2题请选择出划线部分读音不同的选项( )。 A. arm B. party C. warm D. farther 答案：C 第3题请选择出划线部分读音不同的选项( )。 A.energy B.engineer C.encourage D.entrance 答案：C 第4题请选择出划线部分读音不同的选项( )。 A. great B. league C. peace D. neat 答案：A

第5题请选择出划线部分读音不同的选项( )。 A. theory B. throgh C. birth D. there 答案：D 二、词汇与语法知识(15 points) 第6题She kept a close eye__________the sick child and didn’t sleep the whole night. A.at B.in C.for D.on 答案：D 第7题The effect of TV__________the life of average people is incalculable. A.in B.for C.about D.on 答案：D 第8题Jim is the most intelligent，of __________ A.four US https://www.sodocs.net/doc/f718952124.html, four C.the four US https://www.sodocs.net/doc/f718952124.html, of four 答案：B 第9题I like all kinds of fruit，but my __________is banana. A.favorite B.favored C.favorable D.preferred 答案：A 第10题We were overjoyed at the news of China__________ another man-made satel1ite. A.starting B.1aunching C.fighting D.shouting 答案：B

第47期轮机英语

47期轮机英语考试题目一单项选择题 A1.The___ engine is used for alternators and some times for main propulsion provide a propeller of between 90 to 120 rpm. A.four-stroke B.two-stroke. C.slow speed D.reversible B2.The abbreviation”MIP”stands for____, A.middle indicating pressure B.mean indicated pressure C.mean pitch D.middle indicated power D3.The cetane number of a diesel fuel oil indicates its____. A.viscosity B.acid content C.heating value D.ignition quality C4.In a two-stroke engine the camshaft rotates at___the enging rotational speed. A.half B.twice C.the same speed as D.four times D5.A diesel enging is similar to a gasoline engine except that the former has no ____. A.cross-head B.cylinder C.connecting rod D.spark plug C6.It is easier to replace a dry cylinder liner than a wet one because____. A.of the thin wall thickedss B.honing makes it easier to maintain the desired oil film C.water seals are not required D.it fits more loosely due to a decrease in heat transfer through the composite wall D7.A main bearing consists of two shells which are secured by means of studs and____. A.tie rods B.though bolts C.lead wires D.bearing caps C8.However fast or slow the combustion rate,it is still a____between carbon,hydrogen,sulph and oxygen that releases heat. A.physical deformation B.state exchange C.chemical reaction D.coalescence A9.During the fuel injection period,fuel pressure must exceed cylinder gas pressure to____. A.ensure penetration and distribution of the fuel in the combustion chamber B.ensure the needle valves is flushed clean duringeach injection C.prevent combustion gas blowback into the open needle valve Dprevent reflected pressure waves when the neddle valve close. B10.In a diesel engine lube oil system ,which of the following parts should be lubricated first? A.Camshaft bearings B.Main bearings C.Piston crowns D.Cylinder walls B11.In a diesel engine closed freshwater cooling system,the amount of coolant flowing through the heat exchanger is controlled by the _____, A.suction pressure regulator B.thermostatic bypass valve C.sea water temperature D.water level in the expansion tank

轮机大管轮英语真题48期

中华人民共和国海事局 2009年第5期海船船员适任证书全国统考试题(总第48期) 科目：轮机英语试卷代号：803 适用对象：无限、近洋航区3000KW及以上船舶大管轮（本试卷卷面总分100分，及格分为70分，考试时间为100分钟）答题说明：请选择一个最合适的答案，并将该答案按答题卡要求，在其相应位置上用2B铅笔涂黑。第1题至82题，每题1分，第83题至94题，每题1.5分。一、单项选择题： 1. The reason why more and more of the large merchant vessels are being powered by medium-speed diesel engines is . A. they operate between 150 and 450 rpm B. they are connected to the propeller by gearing C. their smaller size and weight D. they can be connected directly to the propeller without gearing 2. The closing of the exhaust valves used on a modern, large, low-speed, main propulsion diesel engine may be directly provided by . A. large conical springs B. compressed air pressure C. hydraulic pressure D. exhaust gas pressure 3. One of the factors limiting the amount of toad which can be put on a modem marine diesel engine is the . A. governor sensitivity B. exhaust temperature C. fuel injection pressure D. speed of the cam shaft 4. The desirable properties or a marine fuel oil should inc lude . A. high flash point and high viscosity B. low flash point and high viscosity C. low heating value and high sulphur content D. high heating value and low sulphur content 5. As the plunger moves upwards in the barrel, injection will commence once the plunger bas the spill ports and the pressure builds up. A. opened up B. closed off C. lined up D. taken off 6. In an auxiliary diesel engine bypass type lubricating oil system, the main lube oil pump forces . A. all of the oil used by the engine through a filter B. some of the oil used by the engine through a filter C. some of the oil used by the engine through a centrifuge D. all of the oil used by the engine through a centrifuge 7. Because the circulating water is in a closed loop, is installed to cater for expansion and contraction of the water at different conditions of operation. A. an expansion joint B. a drain tank C. a head tank D. a contraction tank 8. The high air velocity leaving the compressor of an exhaust gas turbocharger is converted to pressure in the . A. inlet nozzle ring B. turbine wheel blade C. diffuser passages D. inlet volute 9. is usually driven by the engine camshaft and supplies pilot air to the cylinder air start valve. A. An air receiver B. An operating valve C. An automatic valve D. An air distributor 10. Diesel engines driving alternators operating in parallel must maintain a set frequency regardless of load changes. The governor characteristic used to accomplish this is known as . A. actuation B. sensitivity C. compensation D. promptness 11. By comparing the exhaust gas temperature of each cylinder, the operator can determine if the load is balanced throughout the engine. The device most commonly used is a . A. tachometer B. pyrometer C. dynamometer D. calorimeter 12. When the ship is going to enter into the harbor, ____. A. change from heavy fuel oil to diesel oil for main engine B. pumping out bilge water C. change sea chest from high level one to lower level one D. test emergency generator 13. If the jacket water temperature rises rapidly above normal in a diesel engine, you should first . A. place standby cooler in operation B. reduce engine toad C. check thermostatic valve D. clean sea water strainer 14. Air cocks, usually positioned at the in a circulating system, is used to get rid of the air in the system. A. bending joint B. expansion tank C. weld D. the highest point 15. Which of the following conditions could contribute to the cracking of a diesel engine cylinder head? A. Leaking seal ring B. Insufficient heat transfer from the exhaust valves C. Blocked cooling water passages to the head D. Excessive scavenging air provided to the engine 16. of an engine crankshaft can be detected by measuring deflections of' crank webs for each unit of the engine. A. Misalignment B. Length C. Strength D. Stresses 17. can be a direct cause of faulty operation of diesel engine fuel injection nozzles. A. Excessive fuel nozzle holder cooling B. Sediment in the fuel supply C. Distortion of the fuel spray pattern D. Improper atomization of the fuel 18. When fuel is injected late into a diesel engine cylinder . A. the exhaust will be clear B. fuel consumption will be low C. all the fuel will be burned at top dead center D. fuel consumption will be high 19. A large change in ambient temperature, or using an oil of a viscosity different than the one recommended by the manufacturer in a mechanical hydraulic governor, will result m the need to adjust the . A. pilot valve opening B. compensating needle valve C. compensating spring tension D. accumulator spring tension 20. Which of the following factors tends to increase scale formation on the saltwater side of a heat exchanger used in a diesel engine cooling water system? A. Baffle plates that have been bent during prior removal. B. Leaks m the cooler tube nest. C. Operating the engine while maintaining a high sea water outlet temperature. D. A punctured sea water strainer supplying cooling water to the heat exchanger. 21. If the scavenge fire is of a more major nature, if there is a risk of the fire extending or if the scavenge trunk is adjacent to the crankcase with risk of a hot spot developing it sometimes becomes necessary to the engine. A. stop B. start C. speed up D. slow down 22. In an operating diesel engine, which of the following conditions is an indication of a leaking air starting valve?

4月自考英语二试题及答案知识讲解

2014年4月自考英语二00015试题及答案第一部分：阅读判断（10*1分） Running: sport or way of life? You go through the channels several times and find that once again there’s nothing on TV that interests you. Not a problem! Just put on some running shoes and comfortabl e clothes and go for a run. One of the best things about the sport of running is that you d on’t need expensive equipment. All you need is a good pair of running shoes and a safe environment. But d on’t be fool ed into thinking the sport of running is easy. It requires discipline and concentration. Running is good for you both physically and mentally. It strengthens your heart, lungs, and muscl es. It makes you more aware of your body. Running also improves your body so that you d on’t get sick as easily. It can even help you to stay more focused in school because exercise helps you to think more cl early. How d o you get engaged in the sport if you d on’t know much about it? Most schools offer running programs. A simpl e Internet search can help you find some in your area. The programs show you how running can offer competition or just be for fun. They also teach runners to set practical goals and take care of their bodies. Runners have great respect for each other because they know how difficult the sport can be. If you go to a race, you’ll see peopl e cheering for all the runners. Running isn’t always about how fast you are running or how far you’re going. It’s about getting out there and d oing it. Participation is more important than competition, and effort is recognized over talent. It you’re looking for more than just a sport, running may be the perfect choice for you. 1.You may find it interesting to go for a run. A.True B. False C. Not Given 2.The sport of running is easy. A.True B. False C. Not Given 3.It’s hard to find a safe environment for running.

轮机英语历年真题43期

中华人民共和国海事局 2007年第2期海船船员适任证书全国统考试题(总第43期) 科目：轮机英语试卷代号：805 适用对象：无限、近洋航区3000KW及以上船舶二/三管轮（本试卷卷面总分100分，及格分为70分，考试时间为100分钟）答题说明：请选择一个最合适的答案，并将该答案按答题卡要求，在其相应位置上用2B铅笔涂黑。第1题至74题，每题1分，第75题至78题，每题1.5分,第79题至80题, 每题10分。一、单项选择题 1.______ the engines, the diesel engine is ______ used engine on board. A. Between/more commonly B. Among/the most commonly C. Between/not more commonly D. Among/ not the most commonly 2.The average pressure exerted on a piston during each power stroke is termed ______. A. indicated horsepower B. mean effective pressure C. exhaust back pressure D. compression pressure 3.The cetane number rates fuels for diesel engines according to its ______. A. antiknock characteristics B. ignition qualities C. rates of vaporization D. viscosity 4.The time between injection and ignition of the fuel is known as ______. A. turbulence lag B. after burning ratio C. pre-ignition lag D. ignition delay 5.______ controls the fuel oil temperature in order to provide oil at the correct viscosity for combustion. A. The viscosity regulator B. The temperature controller C. The flow meter D. The pressure switch 6.Constant cooling the various components of diesel engine has a number of functions except for ______. A. good lubrication B. low thermal stress C. good mechanical properties D. acid corrosion 7. A device which functions to bring a diesel engine to a full stop to protect it from damage is known as a/an ______. A. torque limiter B. over-speed trip C. over-speed governor D. load limit governor 8.Engine speeds at which resonance can occur are termed ______. A. maximum speeds B. full speeds C. sea speeds D. critical speeds 9.Prolonged operation of a diesel engine with a closed cooling water system at lower than normal designed operating temperatures can ______. A. increase power output B. decrease lube oil viscosity C. eliminate fuel knock D. cause sulfuric acid formation 10.______ on a ship transmits power from the engine to the propeller. A. The automatic control system B. The speed regularly system C. The transmission system D. The compression air system 11.In a _____ boiler the hot gases from the furnace pass through the tubes while the water is on the outside. A. water-tube B. fire-tube C. exhaust gas D. composite 12.The fuel supply system to an automatic auxiliary boiler, will be automatically shutdown if the boiler ______. A.salinity is abnormally B.high steam demand is too high C.feed-water flow is low D.water level is abnormally low 13.The water in a steaming auxiliary boiler should be tested daily for ______. A. dissolved oxygen B. chlorides C. sludge D. dissolved nitrogen 14.Ignition failure in an automatically controlled auxiliary boiler could be caused by ______. A. carbon deposits on the flame scanner B. high fuel oil temperature C. low fuel oil viscosity D. high steam pressure 15.The concentration of total dissolved solids in the water of an auxiliary boiler can increase as a result of ______. A. seawater contamination B. frequent surface blows C. dissolved oxygen de-aeration D. frequent bottom blows