(完整版)材料力学中英对照词汇
材料力学中英对照词汇
A
安全因数safety factor
B
半桥接法half bridge
闭口薄壁杆thin-walled tubes
比例极限proportional limit
边界条件boundary conditions
变截面梁beam of variable cross section 变形deformation
变形协调方程compatibility equation 标距gage length
泊松比Poisson’s ratio
补偿块compensating block
C
材料力学mechanics of materials
冲击荷载impact load
初应力，预应力initial stress
纯剪切pure shear
纯弯曲pure bending
脆性材料brittle materials
D
大柔度杆long columns
单位荷载unit load
单位力偶unit couple
单位荷载法unit-load method
单向应力，单向受力uniaxial stress
等强度梁beam of constant strength
低周疲劳low-cycle fatigue
电桥平衡bridge balancing
电阻应变计resistance strain gage
电阻应变仪resistance strain indicator 叠加法superposition method
叠加原理superposition principle 动荷载dynamic load
断面收缩率percentage reduction in area
多余约束redundant restraint
E
二向应力状态state of biaxial stress
F
分布力distributed force
复杂应力状态state of triaxial stress
复合材料composite material
G
杆，杆件bar
刚度stiffness
刚架，构架frame
刚结点rigid joint
高周疲劳high-cycle fatigue
各向同性材料isotropical material
功的互等定理reciprocal-work theorem
工作应变计active strain gage
工作应力working stress
构件structural member
惯性半径radius of gyration of an area
惯性积product of inertia
惯性矩，截面二次轴距moment of inertia
广义胡克定律generalized Hook’s law
H
横向变形lateral deformation
胡克定律Hook’s law
滑移线slip-lines
J
基本系统primary system
畸变能理论distortion energy theory
畸变能密度distortional strain energy
density极惯性矩，截面二次极矩
polar moment of inertia极限应力
ultimate stress
极限荷载limit load
挤压应力bearing stress
剪力shear force
剪力方程equation of shear force
剪力图shear force diagram
剪流shear flow
剪切胡克定律Hook’s law for shear
剪切shear
交变应力，循环应力cyclic stress
截面法method of sections
截面几何性质geometrical properties of
an area
截面核心core of section
静不定次，超静定次数degree of a
statically indeterminate problem
静不定问题，超静定问题statically
indeterminate problem
静定问题statically determinate problem
静荷载static load
静矩，一次矩static moment
颈缩necking
K
开口薄壁杆bar of thin-walled open cross
section
抗拉强度ultimate stress in tension
抗扭截面系数section modulus in torsion
抗扭强度ultimate stress in torsion
抗弯截面系数section modulus in
bending
L
拉压刚度axial rigidity
拉压杆，轴向承载杆axially loaded bar
理想弹塑性假设elastic-perfectly plastic
assumption
力法force method
力学性能mechanical properties
连续梁continuous beam
连续条件continuity condition
梁beams
临界应力critical stress
临界荷载critical load
M
迈因纳定律Miner’s law
名义屈服强度offset yielding stress
莫尔强度理论Mohr theory of failure
敏感栅sensitive grid
N
挠度deflection
挠曲轴deflection curve
挠曲轴方程equation of deflection curve
挠曲轴近似微分方程approximately
differential equation of the deflection
curve
内力internal forces
扭力矩twisting moment
扭矩torsional moment
扭矩图torque diagram
扭转torsion
扭转极限应力ultimate stress in torsion
扭转角angel of twist
扭转屈服强度yielding stress in torsion
扭转刚度torsional rigidity
O
欧拉公式Euler’s formula
P
疲劳极限，条件疲劳极限endurance
limit
疲劳破坏fatigue rupture
疲劳寿命fatigue life
偏心拉伸eccentric tension
偏心压缩eccentric compression
平均应力average stress
平面弯曲plane bending
平面应力状态state of plane stress
平行移轴定理parallel axis theorem
平面假设
plane cross-section assumption
Q
强度strength
强度理论theory of strength
强度条件strength condition
切变模量shear modulus
切应变shear strain
切应力shear stress
切应力互等定理theorem of conjugate shearing stress
屈服yield
屈服强度yield strength
全桥接线法full bridge
R
热应力thermal stress
S
三向应力状态state of triaxial stress
三轴直角应变花three-element rectangular rosette
三轴等角应变花three-element delta rosette
失稳buckling
伸长率elongation
圣维南原理Saint-Venant’s principle
实验应力分析experimental stress analysis
塑性变形，残余变形plastic deformation
ductile materials塑性材料，延性材料
塑性铰plastic hinge
T
弹簧常量spring constant
弹性变形elastic deformation
弹性模量modulus of elasticity
体积力body force
体积改变能密度density of energy of
volume change
体应变volume strain
W
弯矩bending moment
弯矩方程equation of bending moment
弯矩图bending moment diagram
弯曲bending
弯曲刚度flexural rigidity
弯曲正应力normal stress in bending
弯曲切应力shear stress in bending
弯曲中心shear center
位移法displacement method
位移互等定理reciprocal-displacement
theorem
稳定条件stability condition
稳定性stability
稳定安全因数safety factor for stability
X
细长比，柔度slenderness ratio
线性弹性体linear elastic body
约束扭转constraint torsion
相当长度，有效长度equivalent length
相当应力equivalent stress
小柔度杆short columns
形心轴centroidal axis
形状系数shape factor
许用应力allowable stress
许用应力法allowable stress method
许用荷载allowable load
许用荷载法allowable load method
Y
应变花strain rosette
应变计strain gage
应变能strain energy
应变能密度strain energy density
应力stress
应力速率stress ratio
应力比stress ratio
应力幅stress amplitude
应力状态state of stress
应力集中stress concentration
应力集中因数stress concentration factor
应力－寿命曲线，S-N曲线stress-cycle
curve
应力－应变图stress-strain diagram
应力圆，莫尔圆Mohr’s circle for stresses
Z
正应变normal strain
正应力normal stress
中面middle plane
中柔度杆intermediate columns
中性层neutral surface
中性轴neutral axis
轴shaft
轴力axial force
轴力图axial force diagram
轴向变形axial deformation
轴向拉伸axial tension
轴向压缩axial compression
主平面principal planes
主应力principal stress
主应力迹线principal stress trajectory
主轴principal axis
主惯性矩principal moment of inertia
主形心惯性矩principal centroidal
moments of inertia
主形心轴principal centroidal axis
转角angel of rotation
转轴公式transformation equation
自由扭转free torsion
组合变形combined deformation
组合截面composite area
最大切应力理论maximum shear stress
theory
最大拉应变理论maximum tensile strain
theory
最大拉应力理论maximum tensile stress
theory
最大应力maximum stress
最小应力minimum stress
材料力学词汇
材料力学常用英文词汇 弹性力学elasticity 弹性理论theory of elasticity 均匀应力状态homogeneous state of stress 应力不变量stress invariant 应变不变量strain invariant 应变椭球strain ellipsoid 均匀应变状态homogeneous state of strain 应变协调方程equation of strain compatibility 拉梅常量Lame constants 各向同性弹性isotropic elasticity 旋转圆盘rotating circular disk 楔wedge 开尔文问题Kelvin problem 布西内斯克问题Boussinesq problem 艾里应力函数Airy stress function 克罗索夫--穆斯赫利什维利法Kolosoff-Muskhelishvili method 基尔霍夫假设Kirchhoff hypothesis 板Plate 矩形板Rectangular plate 圆板Circular plate 环板Annular plate 波纹板Corrugated plate 加劲板Stiffened plate,reinforced Plate 中厚板Plate of moderate thickness 弯[曲]应力函数Stress function of bending 壳Shell 扁壳Shallow shell 旋转壳Revolutionary shell 球壳Spherical shell [圆]柱壳Cylindrical shell 锥壳Conical shell 环壳Toroidal shell 封闭壳Closed shell 波纹壳Corrugated shell 扭[转]应力函数Stress function of torsion 翘曲函数Warping function 半逆解法semi-inverse method 瑞利--里茨法Rayleigh-Ritz method 松弛法Relaxation method 莱维法Levy method 松弛Relaxation 量纲分析Dimensional analysis
(完整word版)工程材料常用词汇表(中英文)
工程材料常用词汇表 A 奥氏体 austenite 奥氏体本质晶粒度 austenite inhorent grain size 奥氏体化 austenitization, austenitii zing B 白口铸铁 white cast iron 白铜 white brass, copper-nickel alloy 板条马氏体 lath martensite 棒材 bar 包晶反应 peritectic reaction 薄板 thin sheet 薄膜技术 thin film technique 贝氏体 bainite 本质晶粒度 inherent grain size 比强度 strength-to-weight ratic 变质处理 inoculation, modification 变质剂 modifying agent,modificator 表面处理 surface treatment 表面粗糙度 surface roughness 表面淬火 surface quenching 表面腐蚀 surface corrosion 表面硬化 surface hardening 玻璃 glass 玻璃态 vitreous state, glass state 玻璃钢 glass fiber reinforced plastics 玻璃纤维 glass fiber 不可热处理的 non-heat-treatable 不锈钢 stainless steel 布氏硬度 Brinell hardness C 材料强度 strength ofmaterial 残余奥氏体residual austenite 残余变形 residual deformation 残余应力 residual stress 层状珠光体 lamellar pearlite
焊接专业术语中英文对照整理
机械——焊接专业术语中英文对照 （郭运）整理 1Single 单面的 2V—groove V型坡口 3Joint 焊接接头 4Edges overlap 接头形式 5Butt 对接 6T T型焊接 7Fillet 角焊缝 8Edge 端接 9Corner 角接 10Radius 半径 11Joint root 焊接根部 12Bevel angle 削边角度 13Groove angle 坡口角度 14Root face 根部钝边 15Groove face 坡口面 16Plug weld 塞焊 17Spot weld 点焊 18Seam weld 缝焊 19Slot weld 槽焊 20Double—flare—bevel—groove K型坡口焊缝
21Single—flare—V 单面V型22Edge flange 翻边端接 23Corner flange 卷边端接 24Flange weld 卷边焊缝25Flare weld 扩口焊缝26Fillet weld 角焊缝 27Slot weld 槽焊缝 28Spot weld 点焊缝 29Surfacing weld 堆焊焊缝30Melt—through weld 熔透焊缝31Backing weld 打底焊缝32Back weld 背面焊缝33Root weld 根部焊缝34Crown weld 隆起部分35Weld reinforcement 焊缝加强36Weld face 焊缝表面37Cap pass 盖面焊道38Weld edge 焊缝边缘39Leg 焊脚 40Toe 焊趾 41Buildup 堆焊 42Weld reinforcement 焊缝加强高
土木工程 专业词汇大全中英对照
土木工程专业外语词汇大全中英翻译 1. 综合类 大地工程geotechnical engineering 反分析法back analysis method 基础工程foundation engineering 临界状态土力学critical state soil mechanics 数值岩土力学numerical geomechanics 土soil, earth 土动力学soil dynamics 土力学soil mechanics 岩土工程geotechnical engineering 应力路径stress path 应力路径法stress path method 2. 工程地质及勘察 变质岩metamorphic rock 标准冻深standard frost penetration 冰川沉积glacial deposit 冰积层（台）glacial deposit 残积土eluvial soil, residual soil 层理beding 长石feldspar 沉积岩sedimentary rock 承压水confined water 次生矿物secondary mineral 地质年代geological age 地质图geological map 地下水groundwater 断层fault 断裂构造fracture structure 工程地质勘察engineering geological exploration 海积层（台）marine deposit 海相沉积marine deposit 花岗岩granite 滑坡landslide 化石fossil 化学沉积岩chemical sedimentary rock 阶地terrace 节理joint 解理cleavage 喀斯特karst 矿物硬度hardness of minerals 砾岩conglomerate
常用焊接术语中英文对照
常用焊接术语中英文对照 焊接Welding 10.1 焊接种类Varieties of Welding 电弧焊arc welding 电熔焊electric fusion welding (EFW) 气熔焊fusion gas welding (FGW) 电阻焊electric resistance welding (ERW) 有保护的金属电弧焊shielded metal arc welding (SMAW) 手工或自动隋性气体保护钨极电弧焊manual and automatic inert gas tungsten arc welding (GTAW) 自动埋弧焊automatic submerged arc welding 金属极隋性气体保护电弧焊gas metal arc weiding (GMAW) 氩弧焊argon-arc welding， 气体保护电弧焊gas-shielded arc welding 气焊gas welding; flame welding 等离子焊plasma welding 硬钎焊braze welding 电渣焊electroslag welding 爆炸焊explosive welding 10.2 焊接形式Type of Welding 角焊fillet welding 间断焊intermittent welding 点焊spot welding 对焊butt welding 搭焊lap welding 塞焊plug welding 珠焊bead welding 槽焊slot welding 堆焊build up welding 垫板焊backing weld 坡口groove V形坡口V groove 单面U形坡口single U groove K形坡口double bevel groove X形坡口double V groove 双面U形坡口double U groove U-V组合坡口combination U and V groove 根部间隙root gap 焊接符号symbol of weld 错边量alignment tolerance
土木工程专业英语词汇(整理版)
第一部分必须掌握，第二部分尽量掌握 第一部分： 1 Finite Element Method 有限单元法 2 专业英语Specialty English 3 水利工程Hydraulic Engineering 4 土木工程Civil Engineering 5 地下工程Underground Engineering 6 岩土工程Geotechnical Engineering 7 道路工程Road (Highway) Engineering 8 桥梁工程Bridge Engineering 9 隧道工程Tunnel Engineering 10 工程力学Engineering Mechanics 11 交通工程Traffic Engineering 12 港口工程Port Engineering 13 安全性safety 17木结构timber structure 18 砌体结构masonry structure 19 混凝土结构concrete structure 20 钢结构steelstructure 21 钢-混凝土复合结构steel and concrete composite structure 22 素混凝土plain concrete 23 钢筋混凝土reinforced concrete 24 钢筋rebar 25 预应力混凝土pre-stressed concrete 26 静定结构statically determinate structure 27 超静定结构statically indeterminate structure 28 桁架结构truss structure 29 空间网架结构spatial grid structure 30 近海工程offshore engineering 31 静力学statics 32运动学kinematics 33 动力学dynamics 34 简支梁simply supported beam 35 固定支座fixed bearing 36弹性力学elasticity 37 塑性力学plasticity 38 弹塑性力学elaso-plasticity 39 断裂力学fracture Mechanics 40 土力学soil mechanics 41 水力学hydraulics 42 流体力学fluid mechanics 43 固体力学solid mechanics 44 集中力concentrated force 45 压力pressure 46 静水压力hydrostatic pressure 47 均布压力uniform pressure 48 体力body force 49 重力gravity 50 线荷载line load 51 弯矩bending moment 52 torque 扭矩 53 应力stress 54 应变stain 55 正应力normal stress 56 剪应力shearing stress 57 主应力principal stress 58 变形deformation 59 内力internal force 60 偏移量挠度deflection 61 settlement 沉降 62 屈曲失稳buckle 63 轴力axial force 64 允许应力allowable stress 65 疲劳分析fatigue analysis 66 梁beam 67 壳shell 68 板plate 69 桥bridge 70 桩pile 71 主动土压力active earth pressure 72 被动土压力passive earth pressure 73 承载力load-bearing capacity 74 水位water Height 75 位移displacement 76 结构力学structural mechanics 77 材料力学material mechanics 78 经纬仪altometer 79 水准仪level 80 学科discipline 81 子学科sub-discipline 82 期刊journal ,periodical 83文献literature 84 ISSN International Standard Serial Number 国际标准刊号 85 ISBN International Standard Book Number 国际标准书号 86 卷volume 87 期number 88 专著monograph 89 会议论文集Proceeding 90 学位论文thesis, dissertation 91 专利patent 92 档案档案室archive 93 国际学术会议conference 94 导师advisor 95 学位论文答辩defense of thesis 96 博士研究生doctorate student 97 研究生postgraduate 98 EI Engineering Index 工程索引 99 SCI Science Citation Index 科学引文索引
建筑专业词汇中英对照(精心整理版)
1DESIGN BASIS 设计依据 计划建议书planning proposals 设计任务书design order 标准规范standards and codes 条件图information drawing 设计基础资料basic data for design 工艺流程图process flowchart 工程地质资料engineering geological data 原始资料original data 设计进度schedule of design 2STAGE OF DESIGN 设计阶段 方案scheme, draft 草图sketch 会谈纪要summary of discussion 谈判negotiation 可行性研究feasibility study 初步设计preliminary design 基础设计basic design 详细设计detail design 询价图enquiry drawing 施工图working drawing, construction drawing 竣工图as built drawing 3CLIMATE CONDITION 气象条件 日照sunshine 风玫瑰wind rose 主导风向prevailing wind direction 最大(平均)风速maximum (mean) wind velocity 风荷载wind load 最大(平均)降雨量maximum (mean) rainfall 雷击及闪电thunder and lightning 飓风hurricane 台风typhoon 旋风cyclone 降雨强度rainfall intensity 年降雨量annual rainfall 湿球温度wet bulb temperature 干球温度dry bulb temperature 冰冻期frost period
焊接专用英文词汇
焊接专用英文词汇 1.1 焊接方法 焊接方法与设备（Welding process& facility） 手工电弧焊(MAW:manual arc welding) 电弧焊（arc welding）埋弧电弧焊（SAW：submerged arc welding）气焊（gas welding）氩弧焊（argon arc welding） 气体保护电弧焊 CO2保护焊(CO2 shielded arc welding) 熔化焊（GMAW—gas metal arc welding） fusion welding 电渣焊(ESW—electroslag welding) 激光焊(LW—laster welding) 等离子焊(PAW—plasma arc welding) 摩擦焊（FRW—friction welding） 焊接压力焊超声波焊（UW—ultrasonic welding） welding pressure welding 冷压焊（CPW—cold pressure welding）锻焊（FW—forge-welding）对焊butt welding 电阻焊(RW—resistance welding) 缝焊seam welding 点焊spot welding 烙铁钎焊 iron soldering 火焰钎焊 torch brazing/ torch soldering 钎焊炉中钎焊 furnace brazing/ furnace soldering soldering/brazing 盐浴钎焊 saltbath dip brazing (soldering) 真空钎焊 vacuum brazing 堆焊 overlaying welding 平焊 downhand welding/flat welding 横焊 horizontal welding 立焊 vertical welding 仰焊 overhead welding 全位置焊 all position welding/positional welding 半自动电弧焊 Semi-automatic arc welding 钨极惰性气体保护电弧焊 (TIG) tungsten inert-gas arc welding 熔化极惰性气体保护电弧焊（MIG）metal inert-gas arc welding 1.2 焊接设备 电弧焊机 arc welding machine 直流弧焊机 DC arc welding machine 交流弧焊机 AC arc welding machine 交直流两用弧焊机 AC/DC arc welding machine 氩弧焊机 argon arc welding machine 二氧化碳弧焊机 CO2 arc welding machine 埋弧焊机 submerged arc welding machine 焊接机头 welding head 行走机构 traveller 送丝机构 wire feeder 焊丝盘 wire reel
材料力学词汇中英对照按汉语拼音字母顺序A安全因数safetyfactor
材料力学词汇中英对照 （按汉语拼音字母顺序） A 安全因数safety factor B 半桥接法half bridge 闭口薄壁杆thin-walled tubes 比例极限proportional limit 边界条件boundary conditions 变截面梁beam of variable cross section 变形deformation 变形协调方程compatibility equation 标距gage length 泊松比Poisson’s ratio 补偿块compensating block C 材料力学mechanics of materials 冲击荷载impact load 初应力，预应力initial stress 纯剪切pure shear 纯弯曲pure bending 脆性材料brittle materials
D 大柔度杆long columns 单位荷载unit load 单位力偶unit couple 单位荷载法unit-load method 单向应力，单向受力uniaxial stress 等强度梁beam of constant strength 低周疲劳low-cycle fatigue 电桥平衡bridge balancing 电阻应变计resistance strain gage 电阻应变仪resistance strain indicator 叠加法superposition method 叠加原理superposition principle 动荷载dynamic load 断面收缩率percentage reduction in area 多余约束redundant restraint E 二向应力状态state of biaxial stress F 分布力distributed force 复杂应力状态state of triaxial stress
软件工程专业词汇中英对照
软件工程专业词汇中英 对照 The manuscript was revised on the evening of 2021
Acceptance Testing－－可接受性测试一般由用户/客户进行的确认是否可以接受一个产品的验证性测试。 actual outcome－－实际结果被测对象在特定的条件下实际产生的结果。 Ad Hoc Testing－－随机测试测试人员通过随机的尝试系统的功能，试图使系统中断。 algorithm－－算法一个定义好的有限规则集，用于在有限步骤内解决一个问题；（2）执行一个特定任务的任何操作序列。 algorithm analysis－－算法分析一个软件的验证确认任务，用于保证选择的算法是正确的、合适的和稳定的，并且满足所有精确性、规模和时间方面的要求。 Alpha Testing－－Alpha测试由选定的用户进行的产品早期性测试。这个测试一般在可控制的环境下进行的。 analysis－－分析分解到一些原子部分或基本原则，以便确定整体的特性；（2）一个推理的过程，显示一个特定的结果是假设前提的结果；（3）一个问题的方法研究，并且问题被分解为一些小的相关单元作进一步详细研究。 anomaly－－异常在文档或软件操作中观察到的任何与期望违背的结果。 application software－－应用软件满足特定需要的软件。 architecture－－构架一个系统或组件的组织结构。 ASQ－－自动化软件质量（Automated Software Quality）使用软件工具来提高软件的质量。 assertion－－断言指定一个程序必须已经存在的状态的一个逻辑表达式，或者一组程序变量在程序执行期间的某个点上必须满足的条件。assertion checking－－断言检查用户在程序中嵌入的断言的检查。 audit－－审计一个或一组工作产品的独立检查以评价与规格、标准、契约或其它准则的符合程度。 audit trail －－审计跟踪系统审计活动的一个时间记录。 Automated Testing－－自动化测试使用自动化测试工具来进行测试，这类测试一般不需要人干预，通常在GUI、性能等测试中用得较多。 Backus-Naur Form－－BNF范式一种分析语言，用于形式化描述语言的语法 baseline－－基线一个已经被正式评审和批准的规格或产品，它作为进一步开发的一个基础，并且必须通过正式的变更流程来变更。 Basic Block－－基本块一个或多个顺
结构力学英语词汇
结构力学 结构力学 structural mechanics 结构分析 structural analysis 结构动力学 structural dynamics 拱 Arch 三铰拱 three-hinged arch 抛物线拱 parabolic arch 圆拱 circular arch 穹顶 Dome 空间结构 space structure 空间桁架 space truss 雪载[荷] snow load 风载[荷] wind load 土压力 earth pressure 地震载荷 earthquake loading 弹簧支座 spring support 支座位移 support displacement 支座沉降 support settlement 超静定次数 degree of indeterminacy 机动分析 kinematic analysis 结点法 method of joints 截面法 method of sections 结点力 joint forces 共轭位移 conjugate displacement 影响线 influence line 三弯矩方程 three-moment equation 单位虚力 unit virtual force 刚度系数 stiffness coefficient 柔度系数 flexibility coefficient 力矩分配 moment distribution 力矩分配法 moment distribution method 力矩再分配 moment redistribution 分配系数 distribution factor 矩阵位移法 matri displacement method 单元刚度矩阵 element stiffness matrix 单元应变矩阵 element strain matrix 总体坐标 global coordinates 贝蒂定理 Betti theorem 高斯--若尔当消去法 Gauss-Jordan elimination Method 屈曲模态 buckling mode 复合材料力学 mechanics of composites 复合材料 composite material 纤维复合材料 fibrous composite 单向复合材料 unidirectional composite
专业词汇中英对照翻译——铁路工程词汇
专业词汇中英对照翻译----铁路工程词汇 线路工程 线路工程railway line engineering 铁路勘测;铁道勘测railway reconnaissance 铁路选线;铁道选线railway route selection; railway location; approximate railway location; location of railway route selection 经济勘察economic investigation 地质调查geological survey; geologic survey 方案比较project comparison 铁路勘探;铁道勘探railway exploration 铁路测量;铁道测量railway survey 线路测量route survey; profile survey; longitudinal survey 曲线测量curve survey 既有线测量survey of existing line; survey of existing railway 铁路线路图;铁道线路图railway map 定线location of line 铁路设计;铁道设计railway design 线路设计track design 平面设计plane design 纵断面设计longitudinal section design 横断面设计transverse section design 曲线设计curve design 车站设计station design 站场设计design of stations and yards 标准设计standard design 线路等级line grade 铁路限界;铁道限界railway clearance 建筑限界construction clearance 设计规范code of design 设计标准design standard 铁路线路;铁道线路railway line 铁路曲线;铁道曲线railway curve 缓和曲线transition curve; easement curve; spiral transition curve 小半径曲线small-radius curve 曲线半径curve radius 曲线超高superelevation on curve; cant; elevation of curve 欠超高inadequate superelevation; deficient superelevation 未被平衡加速度unbalanced acceleration 竖曲线vertical curve 坡道gradient 坡度grade; gradient;slope 限制坡度ruling grade; limiting grade 坡度折减grade compensation; compensation of gradient; gradient compensation 避难线refuge siding; catch siding 双线插入段double track interpolation 铁路连接线;铁道连接线railway connecting line 隧道内线路line in tunnel 桥头引线bridge approach 站线siding 站线长度length of station line 铁路标志;铁道标志railway sign 警冲标fouling point indicator; fouling post 线路中心线track center line; central lines of track 线间距离;线间距distance between centres of lines; distance between centers of tracks; midway between tracks 线路试验;线路实验track test; road test; running test 路基subgrade 铁路路基;路基;铁道路基railway subgrade; subgrade 软土路基soft soil subgrade 沙漠路基desert subgrade 冻土路基permafrost subgrade 膨胀土路基subgrade in swelling soil zone 路基基床subgrade bed 路堤embankment; fill 高路堤high-fill embankment 路堑cut; road cutting 深路堑deep cutting 路肩road shoulder; subgrade shoulder 边坡side slope 护坡revetment; slope protection; pitching 路基滑动subgrade slip 滑坡防治landslide preventive treatment 路基排水subgrade drainage 塑料排水板plastic drainage board 路基加固subgrade strengthening 土工织物geotextile 挡土墙;挡墙retaining walls 锚定板anchor plate 锚杆anchor bolt 抗滑桩antiskid pile; anti-slide pile; counter-sliding pile 加筋土reinforced earth 植被vegetation 路基防护subgrade protection 防护工程protective engineering 防护林protection forest 防沙sand proof 固沙stabilization of sand 输导砂sediment transport 路侧建筑物roadside structure 排水沟weeper drain;weep drain; drainage ditch; drain ditch 挡风墙wind-shield wall; wind-break wall 隔声墙sound-proof wall 防雪栅snow fence; snow guard 轨道理论track theory 轨道设计track design 轨道参数track parameter 轨距track gauge; rail gage;rail gauge 轨距加宽track gauge widening 轨底坡cant of rail; rail cant 轨道力学track dynamics; track mechanics 轨道强度track strength 轨道阻力track resistance 道床阻力trackbed resistance; ballast resistance 扣固力fastening force 钢轨应力rail stress 轨道承载力track bearing capacity 轨道稳定性track stability; stability of track 轨道试验;轨道实验track test 轮轨关系wheel-rail interaction; wheel-rail relation 轮轨动力学wheel-rail dynamics 轮轨作用力wheel-rail force 轮轨接触wheel-rail contact 接触应力contact stress 轨道结构track structure 轨道track 铁路轨道;轨道;铁道轨道railway track; track 线路上部建筑;轨道track superstructure; track 重型轨道heavy track 宽轨枕轨道broad sleeper track 板式轨道slab track; slab-track 整体道床轨道monolithic roadbed track 防振轨道anti-vibration track 高架轨道elevated track 无缝线路jointless line; continuously welded rail track; jointless track
金属加工专业术语中英对照
金属加工专业术语中英对照 砂带磨削,用研磨带磨光 abrasive belt grinding n. 砂带 abrasive belt n. 砂轮切断机 abrasive cut-off machine n. 砂轮修整轮 abrasive dressing wheel n. 磨料粒度 abrasive grain n. 研磨用磨料,铁粒 abrasive grit n. 磨料研磨轮 abrasive lapping wheel n. 位置精度 accuracy of position n. 形状精度 accuracy to shape n. 主切削刃 active cutting edge n. 连接器法兰盘 adapter flange n. 共軛齿廓 adjointing flanks n. 找中(心),找正,对中,对准,找平,调直,校直,调整,调准 align n. 角铣刀 angle milling cutter n. 斜面磨削,斜磨法 angular grinding n. 斜面铣削 angular milling n. 斜向切入磨削 angular plunge grinding n. 斜面车削 angular turning n. 刀杆,心轴,柄轴,轴,辊轴 arbour n. 附件,附件机构,联结,固接,联结法 attachment n. 棒料自动车床 automatic bar machine n. 自动镗床 automatic boring machine n. 自动仿形车床 automatic copying lathe n. 自动双轴铣床 automatic double-head milling machine n. 自动车床 automatic lathe n. 自动转塔车床 automatic turret lathe n. 砂带磨床 belt grinding machine n. 台式车床 bench lathe n. 锥齿轮切削机床 bevel gear cutting machine n. 锥齿轮系，锥齿轮传动系统 bevel gear tooth system n. 斜角，斜面，倾斜，斜切，斜角规，万能角尺，圆锥的，倾斜的，斜边，伞齿轮，锥齿轮 bevel n. 镗孔，镗出的孔，钻眼 borehole n. 镗孔夹具 boring fixture n. 镗床 boring machine n. 镗孔，钻孔，穿孔 boring n. 镗刀 boring tool n. 镗铣床 boring, drilling and milling machine n. 拉床，铰孔机，剥孔机 broaching machine n.
焊接专业术语中英对照.
焊接专业术语中英对照焊接欠缺与检验 焊接欠缺welding imperfection 焊接缺陷weld defect 气孔blowhole/ gas pore 针尖状气孔pinhole 密集气孔porosity 条虫状气孔wormhole 裂纹crack 表面裂纹surface crack 咬边undercut 焊瘤overlap 凹坑pit 烧穿burn through 塌陷excessive penetration 未焊透incomplete penetration/ lack of penetration 未熔合lack of fusion/ incomplete fusion 未焊满incompletely filled weld 根部凹陷root concavity 电弧擦伤arc scratch 夹渣slag inclusion 夹杂物inclusion 夹钨tungsten inclusion 白点fish eye/ flake 错边misalignment/ dislocation 焊接检验 试件test piece 试样test specimen 无损检验nondestructive test 破坏检验destructive test 外观检查visual examination 超声波探伤ultrasonic inspection 直射法超声波探伤straight beam method 斜射法超声波探伤angle beam method 液浸法超声波探伤immersion method 射线探伤radiographic inspection/ radiography X射线探伤X-ray radiographic inspection γ射线探伤gamma-ray inspection X射线工业电视探伤X-ray industrial television inspection 磁粉探伤magnetic particle inspection 电磁探伤electromagnetic inspection/ eddy current test 探伤灵敏度flaw detection sensitivity 渗透探伤penetration inspection 荧光探伤flurescent penetrant inspection 着色探伤dye penetrant inspection 密封性检验leak test 气密性检验air tight test 枕形气密检验pillow test 耐压检验pressure test 水压检验hydraulic test 气压检验pneumatic test 液晶检验liquid crystal test 声发射检测acoustic emission testing 面弯试验face bend testing 背弯试验root bend test 侧弯试验side bend test 横弯试验horizontal bend test 纵弯试验axial bend test 压扁试验squeezing test actual weld-throat thick-ness焊缝厚度 all-around weld整周焊缝 all-around weld (整周焊缝)环焊缝 angle butt weld斜对接焊 angle weld角焊 appearance of weld焊缝成形 arc-seam weld电弧缝焊 arc-spot weld电弧点焊 arc-weld电弧焊 aspect ratio of weld焊缝成形系数 at weld edge在焊缝边上 attachment weld连接焊缝 automatic spot weld自动点焊法 automatic weld自动焊接 axis of a weld焊缝行南? 焊接轴线 axis of weld焊缝轴线; 焊接轴线 back of weld焊缝背面 backing groove of weld焊缝反面坡口backing weld底焊; 底焊焊缝 bare metal arc weld裸焊条电弧焊 bead weld珠焊; 堆焊 bead-on-plate weld堆焊焊缝 beading weld凸焊 beam-to-beam weld梁间焊接; 梁式引线焊接block sequence weld分段多层焊 bond weld钢轨接头焊接 bridge seam weld桥缝焊接; 桥线焊 brize weld硬焊 butt weld对接焊缝 butt weld ends对头焊接端 butt-weld碰焊; 平式焊接; 对头焊接 butt-weld in the downhand position对接平焊