H3C MSR路由器配置
配置telnet登录
telnet server enable
创建本地账号与密码
local-user admin
password simple hnjb8013
user-interface vty 0 4
authentication-mode schema
user-role level-15
配置WAN口地址
[H3C]interface GigabitEthernet 0/0
[H3C-GigabitEthernet0/0]ip address 119.57.73.67 255.255.255.248 //IP地址和掩码配置运营商分配的地址
[H3C-GigabitEthernet0/0]quit
2) 设置内网网关
[H3C]interface GigabitEthernet 0/1
[H3C-GigabitEthernet0/1]ip address 192.168.1.1 24//内网网关IP地址
[H3C-GigabitEthernet0/1]quit
设置DHCP
[H3C]dhcp server ip-pool 1
[H3C-dhcp-pool-1]network 192.168.1.0 mask 255.255.255.0
[H3C-dhcp-pool-1]gateway-list 192.168.1.1
[H3C-dhcp-pool-1]address range 192.168.1.2 192.168.1.200 地址池
[H3C-dhcp-pool-1]dns-list202.106.0.20 114.114.114.114 //具体的运营商DNS 地址
[H3C-dhcp-pool-1]quit
4) 在WAN接口配置NAT，实现内网地址上网进行源地址转换。
[H3C]interface GigabitEthernet 0/0
[H3C-GigabitEthernet0/0]nat outbound
5) 配置默认路由
[H3C]ip route-static 0.0.0.0 0.0.0.0 119.57.73.65 //下一跳地址配置运营商分配的网关地址
Nat一对一NAT
[H3C]nat static outbound 192.168.1.248 119.57.73.70
[H3C]interface GigabitEthernet0/0
[H3C-GigabitEthernet0/0]ip address 119.57.73.70 255.255.255.248 sub
[H3C-GigabitEthernet0/0]nat static enable
[H3C-GigabitEthernet0/0]quit
NAT端口映射
[H3C]interface GigabitEthernet 0/0 //进入设备公网接口
[H3C-GigabitEthernet0/0]
nat server protocol tcp global 119.57.73.67 5366 inside 192.168.1.67 5366
nat server protocol tcp global 119.57.73.67 5367 inside 192.168.1.67 5367
nat server protocol tcp global 119.57.73.67 8081 inside 192.168.1.244 8081
nat server protocol tcp global 119.57.73.67 8123 inside 192.168.1.250 8443
nat server protocol tcp global 119.57.73.67 33890 inside 192.168.1.88 3389
L2TP over ipsec
1.开启L2TP功能。
[H3C]l2tp enable
2.配置本地用户名和密码，可配置多个用户
[H3C]local-user hnjb class network //配置拨号用户名
New local user added.
[H3C-luser-network-hnjb]password simple hnjb8013//配置拨号密码[H3C-luser-network-hnjb]service-type ppp
[H3C-luser-network-hnjb]quit
3. 配置用户认证方式和IP地址池
[H3C]domain system
[H3C-isp-system]authentication ppp local //配置PPP用户的认证方式为本地认证
[H3C-isp-system]quit
[H3C]ip pool 10 10.1.1.10 10.1.1.100 //配置为拨入终端分配的IP地址范围
4. 创建虚拟模板接口
[H3C]interface Virtual-Template0
[H3C-Virtual-Template0]ppp authentication-mode chap//配置本端PPP协议对终端的验证方式为CHAP
[H3C-Virtual-Template0]remote address pool 10 //在虚模板视图下指定为用户分配IP的地址池
[H3C-Virtual-Template0]ip address 10.1.1.1 24
[H3C-Virtual-Template0] ppp ipcp dns 219.141.140.10 114.114.114.114 配置DNS
[H3C-Virtual-Template0]quit
5.创建并配置L2TP组
[H3C]l2tp-group 1 mode lns
[H3C-l2tp1]undo tunnel authentication //取消L2TP隧道验证功能，因为很多终端系统不支持隧道验证功能。
[H3C-l2tp1]allow l2tp virtual-template 0
[H3C-l2tp1]quit
配置IPsec功能
A. 创建并进入一个IKE keychain视图，该视图用于配置IKE对等体的密钥信息。
[H3C]ike keychain keychain1
[H3C-ike-keychain-keychain1]pre-shared-key address 0.0.0.0 0.0.0.0 key simple hnjb2017 //配置预共享密钥123456。
[H3C-ike-keychain-keychain1]quit
配置IKE对等体
[H3C]ike profile profile1
[H3C-ike-profile-profile1]keychain keychain1
[H3C-ike-profile-profile1]local-identity address 119.57.73.67//指定标识本端身份的IP地址。
[H3C-ike-profile-profile1]match remote identity address 0.0.0.0 0.0.0.0 //指定对端身份FQDN名称。
[H3C-ike-profile-profile1]proposal 1 2 3 4 5 6
[H3C-ike-profile-profile1]quit
配置IPsec安全提议
[H3C]ipsec transform-set tran1
[H3C-ipsec-transform-set-tran1]esp encryption-algorithm des-cbc
[H3C-ipsec-transform-set-tran1]esp authentication-algorithm md5
[H3C-ipsec-transform-set-tran1]quit
配置IPSec安全策略模板
[H3C]ipsec policy-template msr 1
[H3C-ipsec-policy-template-msr-1]ike-profile profile1//引用之前配置的IKE对等体
[H3C-ipsec-policy-template-msr-1]transform-set 1 2 3 4 5 6 //引用之前配置的IPsec安全提议
[H3C-ipsec-policy-template-msr-1]quit
创建IPSec安全策略并引用安全策略模板
[H3C]ipsec policy 123 1 isakmp template msr
在公网接口上应用IPsec安全策略。
[H3C]interface GigabitEthernet 0/0
[H3C-GigabitEthernet0/0]ipsec apply policy 123
ike proposal 1
encryption-algorithm aes-cbc-128
dh group2
authentication-algorithm md5
ike proposal 2
encryption-algorithm 3des-cbc
dh group2
authentication-algorithm md5
ike proposal 3
encryption-algorithm 3des-cbc
dh group2
ike proposal 4
encryption-algorithm aes-cbc-256
dh group2
ike proposal 5
dh group2
ike proposal 6
encryption-algorithm aes-cbc-192
dh group2
ipsec transform-set 1
encapsulation-mode transport
esp encryption-algorithm 3des-cbc esp authentication-algorithm md5
ipsec transform-set 2
encapsulation-mode transport
esp encryption-algorithm aes-cbc-128 esp authentication-algorithm sha1
ipsec transform-set 3
encapsulation-mode transport
esp encryption-algorithm aes-cbc-256 esp authentication-algorithm sha1
ipsec transform-set 4
encapsulation-mode transport
esp encryption-algorithm des-cbc esp authentication-algorithm sha1
ipsec transform-set 5
encapsulation-mode transport
esp encryption-algorithm 3des-cbc esp authentication-algorithm sha1
ipsec transform-set 6
encapsulation-mode transport
esp encryption-algorithm aes-cbc-192 esp authentication-algorithm sha1
H3C VDI安装配置指导
目录 1概述···························································································································· 1-1 1.1 产品简介···················································································································1-1 1.2 产品组件···················································································································1-1 1.3 典型组网···················································································································1-2 1.3.1 组织架构··········································································································1-2 1.3.2 典型组网··········································································································1-2 2安装前的准备工作·········································································································· 2-1 2.1 安装前需确认的内容····································································································2-1 2.2 Broker服务器配置要求 ································································································2-1 2.3 AD服务器配置要求·····································································································2-1 2.4 CAS服务器配置要求···································································································2-2 3安装VDI云桌面管理平台 ································································································ 3-1 3.1 安装CAS ··················································································································3-1 3.2 安装AD域控服务器 ····································································································3-1 3.2.1 通过命令行启动安装域控制器和DNS配置。 ···························································3-1 3.2.2 在弹出的对话框中点击下一步。 ············································································3-2 3.2.3 在弹出的对话框中点击下一步。 ············································································3-3 3.2.4 在弹出的对话框中选中”在心林中新建域”，点击下一步。 ············································3-3 3.2.5 在弹出的对话框输入根级域名，点击下一步。 ··························································3-4 3.2.6 选中正确的林功能级别(本服务器安装的是2008 Server R2)，点击下一步 . ·····················3-5 3.2.7 自动配置DNS ···································································································3-6 3.2.8 因为没有创建DNS服务器委派,弹出警告提示,单击”是”继续下一步································3-8 3.2.9 指定AD域的数据库.日志文件的存放路径································································3-9 3.2.10 设定administrator的密码,单击”下一步”······························································· 3-10 3.2.11 查看安装域控前的摘要信息,确认无误后单击下一步················································ 3-11 3.2.12 配置域控服务 ································································································ 3-11 3.2.13 安装完成后,重新启动服务器·············································································· 3-12 3.3 安装Broker服务器 ··································································································· 3-13 3.3.1 解压VDI安装包 ······························································································ 3-13 3.3.2 修改数据库配置······························································································· 3-13 3.3.3 CAS服务器数据库配置 ····················································································· 3-14 3.3.4 初始化数据并注册系统服务················································································ 3-15 3.3.5 运行VDI Broker服务························································································ 3-15 i
H3C S5600系列交换机典型配置举例
S5600系列交换机典型配置举例 2.1.1 静态路由典型配置 1. 组网需求 (1)需求分析 某小型公司办公网络需要任意两个节点之间能够互通，网络结构简单、稳定， 用户希望最大限度利用现有设备。用户现在拥有的设备不支持动态路由协议。 根据用户需求及用户网络环境，选择静态路由实现用户网络之间互通。 (2)网络规划 根据用户需求，设计如图2-1所示网络拓扑图。 图2-1 静态路由配置举例组网图 2. 配置步骤 交换机上的配置步骤： # 设置以太网交换机Switch A的静态路由。
[SwitchB] ip route-static 1.1.1.0 255.255.255.0 1.1.3.1 # 设置以太网交换机Switch C的静态路由。
H3C路由器配置实例
通过在外网口配置nat基本就OK了，以下配置假设Ethernet0/0为局域网接口，Ethernet0/1为外网口。 1、配置内网接口（E t h e r n e t0/0）：[M S R20-20]i n t e r f a c e E t h e r n e t0/0 [M S R20-20 2、使用动态分配地址的方式为局域网中的P C分配地址[M S R20-20]d h c p s e r v e r i p-p o o l 1 [M S R20-20-d h c p-p o o l-1]n e t w o r k2 4 [M S R20-20 [M S R20-20 3、配置n a t [M S R20-20]n a t a d d r e s s-g r o u p1公网I P公网I P [MSR20-20]acl number 3000 [MSR20-20-acl-adv-3000]rule 0 permit ip 4、配置外网接口（Ethernet0/1） [MSR20-20] interface Ethernet0/1 [MSR20-20- Ethernet0/1]ip add 公网IP [MSR20-20- Ethernet0/1] nat outbound 3000 address-group 1 5．加默缺省路由 [MSR20-20]route-stac 0.0.0外网网关 总结： 在2020路由器下面, 配置外网口, 配置内网口, 配置acl 作nat, 一条默认路由指向电信网关. ok! Console登陆认证功能的配置 关键词：MSR;console; 一、组网需求： 要求用户从console登录时输入已配置的用户名h3c和对应的口令h3c，用户名和口令正确才能登录成功。 二、组网图： 三、配置步骤：
H3C交换机DHCP服务器接口地址池典型配置指导
1.2 DHCP服务器接口地址池典型配置指导 1.2.1 组网图 图1-2 DHCP服务器接口地址池配置举例 1.2.2 应用要求 ●Switch A作为DHCP服务器，其VLAN接口1的IP地址为192.168.0.1/24； ●客户端属于VLAN1，通过DHCP方式动态获取IP地址； ●DHCP服务器通过接口地址池为MAC地址为000D-88F7-0001的客户文件服务器分配固定的IP地址192.168.0.10/24，为其它客户端主机分配192.168.0.0/24网段的IP地址，有效期限为10天。DNS服务器地址为192.168.0.20/24，WINS服务器地址为192.168.0.30/24。 1.2.3 适用产品、版本 表1-2 配置适用的产品与软硬件版本关系 1.2.4 配置过程和解释 # 使能DHCP服务
[SwitchA-Vlan-interface1] ip address 192.168.0.1 24 # 配置VLAN接口1工作在DHCP接口地址池模式 [SwitchA-Vlan-interface1] dhcp select interface # 配置DHCP接口地址池中的静态绑定地址 [SwitchA-Vlan-interface1] dhcp server static-bind ip-address 192.168.0.10 mac-address 000D-88F7-0001 # 配置DHCP接口地址池的地址池范围、DNS服务器地址、WINS服务器地址 [SwitchA-Vlan-interface1] dhcp server expired day 10 [SwitchA-Vlan-interface1] dhcp server dns-list 192.168.0.20 [SwitchA-Vlan-interface1] dhcp server nbns-list 192.168.0.30 [SwitchA-Vlan-interface1] quit 1.2.5 完整配置 # interface Vlan-interface1 ip address 192.168.0.1 255.255.255.0 dhcp select interface dhcp server static-bind ip-address 192.168.1.10 mac-address 000d-88f7-0001 dhcp server dns-list 192.168.0.20 dhcp server nbns-list 192.168.0.30 dhcp server expired day 10 # dhcp server forbidden-ip 192.168.0.10 dhcp server forbidden-ip 192.168.0.20 dhcp server forbidden-ip 192.168.0.30 # 1.2.6 配置注意事项 当DHCP服务器采用接口地址池模式分配地址时，在接口地址池中的地址分配完之后，将会从包含该接口地址池网段的全局地址池中挑选IP地址分配给客户端，从而导致获取到全局地址池地址的客户端与获取到接口地址池地址的客户端处在不同网段，无法正常进行通信。 故在本例中，建议从VLAN接口1申请IP地址的客户端数目不要超过250个。
史上最详细H3C路由器NAT典型配置案例
H3C路由器NAT典型配置案列（史上最详细）神马CCIE，H3CIE,HCIE等网络工程师日常实施运维必备，你懂的。 NAT典型配置举例 内网用户通过NAT地址访问外网（静态地址转换） 1. 组网需求 内部网络用户使用外网地址访问Internet。 2. 组网图 图1-5 静态地址转换典型配置组网图 3. 配置步骤 # 按照组网图配置各接口的IP地址，具体配置过程略。 # 配置内网IP地址到外网地址之间的一对一静态地址转换映射。
There are 1 outbound static NAT mappings. IP-to-IP: Local IP : Global IP : Interfaces enabled with static NAT: There are 1 interfaces enabled with static NAT. Interface: GigabitEthernet1/2 # 通过以下显示命令，可以看到Host访问某外网服务器时生成NAT会话信息。[Router] display nat session verbose Initiator: Source IP/port: Destination IP/port: VPN instance/VLAN ID/VLL ID: -/-/- Protocol: ICMP(1) Responder: Source IP/port: Destination IP/port: VPN instance/VLAN ID/VLL ID: -/-/- Protocol: ICMP(1) State: ICMP_REPLY Application: INVALID Start time: 2012-08-16 09:30:49 TTL: 27s Interface(in) : GigabitEthernet1/1 Interface(out): GigabitEthernet1/2 Initiator->Responder: 5 packets 420 bytes Responder->Initiator: 5 packets 420 bytes Total sessions found: 1 内网用户通过NAT地址访问外网（地址不重叠） 1. 组网需求
H3C路由器设置
H3C路由器设置 1. 端口映射 如某公司内网有做游戏或者其他服务机器，需要外网的机器访问时，需要设置端口映射 内部机器:192.168.2.223 外网IP:61.190.38.198 需要做端口映射:在NAT配置中设置 2. 内网中的PC通过域名访问内部的服务器 内部服务器IP:192.168.3.2(VLAN3) TCP端口:80和3777 内部PC机:192.168.2.0/24和192.168.1.0/24(VLAN2和VLN1) 命令配置: Acl number 3400 Rule 0 permit tcp source 192.168.2.0 0.0.0.255 destination 192.168.3.2 0 destination-port eg 80 Rule 5 permit tcp source 192.168.2.0 0.0.0.255 destination 192.168.3.2 0 destination-port eg 3777
Rule 10 permit tcp source 192.168.1.0 0.0.0.255 destination 192.168.3.2 0 destination-port eg 80 Rule 15 permit tcp source 192.168.1.0 0.0.0.255 destination 192.168.3.2 0 destination-port eg 3777 Interface vlan-interface 3 Nat outbound 3400 注:acl的子网掩码和子网掩码是相反的，192.168.1.0/24的子网掩码是255.255.255.0 则acl的子网掩码是0.0.0.255 3. IP和MAC地址绑定 防止ARP欺骗 1) arp扫描:ARP防攻击 2) 固化 4. 互联网访问控制 1) 设置时间
H3C IPv6 静态路由配置
操作手册 IP路由分册 IPv6 静态路由目录 目录 第1章 IPv6静态路由配置......................................................................................................1-1 1.1 IPv6静态路由简介.............................................................................................................1-1 1.1.1 IPv6静态路由属性及功能........................................................................................1-1 1.1.2 IPv6缺省路由..........................................................................................................1-1 1.2 配置IPv6静态路由.............................................................................................................1-2 1.2.1 配置准备..................................................................................................................1-2 1.2.2 配置IPv6静态路由...................................................................................................1-2 1.3 IPv6静态路由显示和维护..................................................................................................1-2 1.4 IPv6静态路由典型配置举例（路由应用）.........................................................................1-3 1.5 IPv6静态路由典型配置举例（交换应用）.........................................................................1-5
H3C路由器配置命令
telnet 防火墙IP地址 用户名 密码 --进入普通用户权限-- --在此命令下可输入一般命令-- --可用?看有哪些命令和命令的作用-- system-view --进入超级管理员权限界面-- --此提示符下可输绝大部分命令-- --(极少数需要在com终端输入)-- quit --退出当前状态，返回上一级-- 一般命令(不一定要把命令写全) display current 展示当前配置 acl number 3050 进入访问控制列表3050号 rule 66 permit ip ........ 在当前访问控制表增加或修改规则66号 rule的具体用法可用rule ?一步步显示出来,亦可参考我原写的命令 我原配置需要涉及的部分 1.ip和mac绑定,绑定方法具体看一下参数文件你就可明白 2.策略号3050 在该条策略中如有permit就是允许你指定的ip或ip段上网 3.策略号3051和305作用是限流 在该策略号具体用法可参考其中的rule规则 最后是save 否则一重启这些改动就会无效 sH3C路由器 ##################################################################### 1、system-view 进入系统视图模式 2、sysname R1 为设备命名为R1 3、display ip routing-table 显示当前路由表 4、 language-mode Chinese|English 中英文切换 5、interface Ethernet 0/0 进入以太网端口视图
6、 ip address 192.168.1.1 255.255.255.0 配置IP地址和子网掩码 7、 undo shutdown 打开以太网端口 8、 shutdown 关闭以太网端口 9、 quit 退出当前视图模式 10、 ip route-static 192.168.2.0 255.255.255.0 192.168.12.2 description To.R2 配置静态路由 11、 ip route-static 0.0.0.0 0.0.0.0 192.168.12.2 description To.R2 配置默认的路由 H3C S3100 Switch H3C S3600 Switch H3C MSR 20-20 Router ##################################################################### 1、调整超级终端的显示字号； 2、捕获超级终端操作命令行，以备日后查对； 3、 language-mode Chinese|English 中英文切换； 4、复制命令到超级终端命令行，粘贴到主机； 5、交换机清除配置 :
ict企业网关h3c路由器配置实例
ICT企业网关H3C路由器配置实例 以下是拱墅检查院企业网关的配置实例。路由器是选H3C MRS20-10（ICG2000），具体配置的内容是： PPP+DHCP+NAT+WLAN [H3C-Ethernet0/2] # version 5.20, Beta 1605 # sysname H3C # domain default enable system # dialer-rule 1 ip permit # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable
# dhcp server ip-pool 1 network 192.168.1.0 mask 255.255.255.0 gateway-list 192.168.1.1 dns-list 202.101.172.35 202.101.172.46 # acl number 2001 rule 1 permit source 192.168.1.0 0.0.0.255 # wlan service-template 1 crypto ssid h3c-gsjcy authentication-method open-system cipher-suite wep40 wep default-key 1 wep40 pass-phrase 23456 service-template enable # wlan rrm 11a mandatory-rate 6 12 24 11a supported-rate 9 18 36 48 54 11b mandatory-rate 1 2 11b supported-rate 5.5 11 11g mandatory-rate 1 2 5.5 11
H3C路由器配置命令
1、system-view 进入系统视图模式 2、sysname 为设备命名 3、display current-configuration 当前配置情况 4、 language-mode Chinese|English 中英文切换 5、interface Ethernet 1/0/1 进入以太网端口视图 6、 port link-type Access|Trunk|Hybrid 设置端口访问模式 7、 undo shutdown 打开以太网端口 8、 shutdown 关闭以太网端口 9、 quit 退出当前视图模式 10、 vlan 10 创建VLAN 10并进入VLAN 10的视图模式 11、 port access vlan 10 在端口模式下将当前端口加入到vlan 10中 12、port E1/0/2 to E1/0/5 在VLAN模式下将指定端口加入到当前vlan 中 13、port trunk permit vlan all 允许所有的vlan通过 H3C路由器 ##################################################################### ################# 1、system-view 进入系统视图模式 2、sysname R1 为设备命名为R1 3、display ip routing-table 显示当前路由表 4、 language-mode Chinese|English 中英文切换 5、interface Ethernet 0/0 进入以太网端口视图 6、 ip address 配置IP地址和子网掩码 7、 undo shutdown 打开以太网端口 8、 shutdown 关闭以太网端口 9、 quit 退出当前视图模式 10、 ip route-static description To.R2 配置静态路由 11、 ip route-static description To.R2 配置默认的路由 H3C S3100 Switch H3C S3600 Switch H3C MSR 20-20 Router ##################################################################### ##################### 1、调整超级终端的显示字号； 2、捕获超级终端操作命令行，以备日后查对； 3、 language-mode Chinese|English 中英文切换； 4、复制命令到超级终端命令行，粘贴到主机；
h3c路由器典型配置案例
version 5.20, Release 2104P02, Basic # sysname H3C # nat address-group 27 122.100.84.202 122.100.84.202 # # domain default enable system # dns resolve dns proxy enable # telnet server enable # dar p2p signature-file cfa0:/p2p_default.mtd # port-security enable # # vlan 1 # domain system access-limit disable state active idle-cut disable self-service-url disable # dhcp server ip-pool 1 network 192.168.201.0 mask 255.255.255.0 gateway-list 192.168.201.1 dns-list 202.106.0.20 202.106.46.151 # # user-group system # local-user admin password cipher .]@USE=*8 authorization-attribute level 3 service-type telnet # interface Aux0 async mode flow link-protocol ppp
interface Cellular0/0 async mode protocol link-protocol ppp # interface Ethernet0/0 port link-mode route nat outbound address-group 27 ip address 122.100.84.202 255.255.255.202 # interface Ethernet0/1 port link-mode route ip address 192.168.201.1 255.255.255.0 # interface NULL0 # # ip route-static 0.0.0.0 0.0.0.0 122.100.84.201 # dhcp enable # load xml-configuration # user-interface con 0 user-interface tty 13 user-interface aux 0 user-interface vty 0 4 authentication-mode scheme user privilege level 3 set authentication password simple###￥￥￥# return [H3C]
H3C配置telnet的具体步骤
本文主要给大家讲述了对于H3C如何去配置telｎet，它的具体步骤和命令都有哪些,下面的文章将给予你详细的介绍，相信看完此文会对你有所帮助。 1.配置H3C tｅlnｅt登陆的ｉｐ地址? ２．进入用户界面视图 ３．设置认证方式为密码验证方式 ４.设置登陆验证的ｐaｓｓｗord为明文密码"huawei"? 5．配置登陆用户的级别为最高级别3(缺省为级别1) ?仅密码方式登陆:? 1．配置H3C ｔelnet登陆的ip地址 [SwitcｈA]interｆａcｅ vlａn １??［SwitｃhA-Ｖlaｎ-ｉnterfａｃe１]ip aｄdｒｅｓs 192.168．0.1 24 ?2．进入配置H3Ｃ tｅｌnet的用户界面视图? [SwiｔchA]ｕser-inｔerｆａce vtｙ 0 4 ? 3.设置认证方式为密码验证方式 [SwitｃhA-ｕi-vty0-4]ａｕtheｎｔication-modｅ paｓｓwoｒd ([schｅｍe],用于验证用户名和密码的模式) ?４.设置登陆验证的ｐaｓｓworｄ为明文密码"huawei＂ (若选用scheme模式，则不需要这一条) [SwiｔｃhA-ui-vｔy０－4]ｓet auｔheｎtｉｃａtiｏn paｓsｗord sｉmｐle ｈｕaweｉ?? 5.配置登陆用户的级别为最高级别３(缺省为级别1）? [ＳwitchA-ui-vｔy０-４]user priｖilege level ３?如第３条选用了ｓｃhｅｍe模式,则要加下面这一命令:? ６．添加tｅlnｅt管理的用户，用户类型为"teｌnet",用户名为"ｈuaｗei＂,密码为＂ aｄｍｉn" ?[SｗｉｔchＡ]lｏcal－uｓｅr ｈuaｗei??[SwitｃhA-ｌｕｓer－huawei]seｒviｃe－tｙpetｅlｎetlｅｖel ３ ? [ＳｗｉtcｈA-ｌｕｓｅr-huaｗei］passwｏrd siｍｐle adｍin? H3C路由器常用基本配置命令 [Quidway]sysname router_name 命名路由器(或交换机) [Quidway]delete 删除Flash ROM中的配置 [Quidway]save 将配置写入Flash ROM [Quidway]interface serial 0 进入接口配置模式 [Quidway]quit 退出接口模式到系统视图 [Quidway]shutdown/undo shutdown 关闭/重启接口 [Quidway]ip address ip_address subnet_mask 为接口配置IP地址和子网掩码 [Quidway]display version 显示VRP版本号 [Quidway]display current-configuration 显示系统运行配置信息 [Quidway]display interfaces 显示接口配置信息 [Quidway]display ip routing 显示路由表 [Quidway]ping ip_address 测试网络连通性 [Quidway]tracert ip_address 测试数据包从主机到目的地所经过的网关 [Quidway]debug all 打开所有调试信息 [Quidway]undo debug all 关闭所有调试信息 [Quidway]info-center enable 开启调试信息输出功能 [Quidway]info-center console dubugging 将调试信息输出到PC [Quidway]info-center monitor dubugging 将调试信息输出到Telnet终端或哑终端 换机配置命令举例(大括号{}中的选项为单选项，斜体字部分为参数值 [Quidway]super password password 修改特权模式口令 [Quidway]sysname switch_name 命名交换机(或路 [Quidway]interface ethernet 0/1 进入接口视图 [Quidway]quit 退出系统视图 [Quidway-Ethernet0/1]duplex {half|full|auto} 配置接口双工工 H3C路由器NAT典型配置案列（史上最详细） 神马CCIE，H3CIE,HCIE等网络工程师日常实施运维必备，你懂的。 1.11 NAT典型配置举例 1.11.1 内网用户通过NAT地址访问外网（静态地址转换） 1. 组网需求 内部网络用户10.110.10.8/24使用外网地址202.38.1.100访问Internet。 2. 组网图 图1-5 静态地址转换典型配置组网图 3. 配置步骤 # 按照组网图配置各接口的IP地址，具体配置过程略。 # 配置内网IP地址10.110.10.8到外网地址202.38.1.100之间的一对一静态地址转换映射。 H3C路由器配置命令
[史上最详细]H3C路由器NAT典型配置案例