MCS-51系列单片机中英文资料对照外文翻译文献综述

.

MCS-51系列单片机

中英文资料对照外文翻译文献综述

Structure and function of the MCS-51 series

Structure and function of the MCS-51 series one-chip computer MCS-51 is a name of a piece of one-chip computer series which Intel Company produces. This company introduced 8 top-grade one-chip computers of MCS-51 series in 1980 after introducing 8 one-chip computers of MCS-48 series in 1976. It belong to a lot of kinds this line of one-chip computer the chips have, such as 8051, 8031, 8751, 80C51BH, 80C31BH,etc., their basic composition, basic performance and instruction system are all the same.8051 daily representatives-51 serial one-chip computers.

A one-chip computer system is made up of several following parts: (1) One microprocessor of 8 (CPU). ( 2) At slice data memory RAM (128B/256B),it use not depositing not can reading /data that write, such as result not middle of operation, final result and data wanted to show, etc. (3)

Procedure memory ROM/EPROM (4KB/8KB ), is used to preserve the procedure , some initial data and form in slice. But does not take ROM/EPROM within some one-chip computers, such as 8031, 8032.(4) Four 8 run side by side I/O interface P0 four P3, each mouth can use as introduction , may use as exporting too. (5) Two timer / counter, each timer / counter may set up and count in the way, used to count to the external incident, can set up into a timing way too, and can according to count or result of timing realize the control of the computer. (6) Five cut off cutting off the control system of the source. (7) One all duplex serial I/O mouth of UART (universal asynchronous receiver/transmitter (UART) ), is it realize one-chip computer or one-chip computer and serial communication of computer to use for. (8) Stretch oscillator and clock produce circuit, quartz crystal finely tune electric capacity need outer. Allow oscillation frequency as 12 megahertz now at most. Every the above-mentioned part was joined through the inside data bus .Among them, CPU is a core of the one-chip computer, it is the control of the computer and command centre, made up of such parts as arithmetic unit and controller , etc.. The arithmetic unit can carry on 8 persons of arithmetic operation and unit ALU of logic operation while including one, the 1 storing device temporaries of 8, storing device 2 temporarily, 8's accumulation device ACC, register B and procedure state register PSW, etc. Person who accumulate ACC count by 2 input ends entered of checking etc. temporarily as one operation often, come from person who store 1 operation is it is it make operation to go on to count

temporarily , operation result and loop back ACC with another one. In addition, ACC is often regarded as the transfer station of data transmission on 8051 inside. The same as general microprocessor, it is the busiest register. Help remembering that agreeing with a express in the order. The controller includes the procedure counter, the order is deposited, the order deciphering, the oscillator and timing circuit, etc. The procedure counter is made up of counter of 8 for two, amounts to 16. It is a byte address counter of the procedure in fact, the content is the next IA that will carried out in PC. The content which changes it can change the direction that the procedure carries out. Shake the circuit in 8051 one-chip computers, only need outer quartz crystal and frequency to finely tune the electric capacity, its frequency range is its 12MHZ of 1.2MHZ. This pulse signal, as 8051 basic beats of working, namely the minimum unit of time. 8051 is the same as other computers, the work in harmony under the control of the basic beat, just like an orchestra according to the beat play that is commanded.

There are ROM (procedure memory , can only read ) and RAM in 8051 slices (data memory, can is it can write ) two to read, they have each independent memory address space, dispose way to be the same with general memory of computer. Procedure 8051 memory and 8751 slice procedure memory capacity 4KB, address begin from 0000H, used for preserving the procedure and form constant. Data 8051- 8751 8031 of memory data memory 128B, address false 00FH, using for middle result to deposit operation, the data are stored temporarily and the data are buffered. In RAM

of this 128B, there is unit of 32 bytes that can be appointed as the job register, this and general microprocessor is different, 8051 slice RAM and job register rank one formation the same to arrange the location. It is not very the same that the memory of MCS-51 series one-chip computer and general computer disposes the way in addition. General computer for first address space, ROM and RAM can arrange in different space within the range of this address at will, namely the addresses of ROM and RAM, with distributing different address space in a formation. While visiting the memory, corresponding and only an address Memory unit, can ROM, it can be RAM too, and by visiting the order similarly. This kind of memory structure is called the structure of Princeton. 8051 memories are divided into procedure memory space and data memory space on the physics structure, there are four memory spaces in all: The procedure stores in one and data memory space outside data memory and one in procedure memory space and one outside one, the structure forms of this kind of procedure device and data memory separated form data memory, called Harvard structure. But use the angle from users, 8051 memory address space is divided into three kinds: (1) In the slice, arrange blocks of FFFFH, 0000H of location, in unison outside the slice (use 16 addresses). (2) The data memory address space outside one of 64KB, the address is arranged from 0000H 64KB FFFFH (with 16 addresses) too to the location. (3) Data memory address space of 256B (use 8 addresses). Three above-mentioned memory space addresses overlap, for distinguishing and designing the order symbol of different data

transmission in the instruction system of 8051: CPU visit slice, ROM order spend MOVC , visit block RAM order uses MOVX outside the slice, RAM order uses MOV to visit in slice.

8051 one-chip computer have four 8 walk abreast I/O ports, call P0, P1, P2 and P3. Each port is 8 accurate two-way mouths, accounts for 32 pins altogether. Every one I/O line can be used as introduction and exported independently. Each port includes a latch (namely special function register), one exports the driver and a introduction buffer. Make data can latch when outputting, data can buffer when making introduction, but four function of pass away these self-same. Expand among the system of memory outside having slice, four ports these may serve as accurate two-way mouth of I/O in common use. Expand among the system of memory outside having slice, P2 mouth see high 8 address off; P0 mouth is a two-way bus, send the introduction of 8 low addresses and data / export in timesharing The circuit of 8051 one-chip computers and four I/O ports is very ingenious in design. Familiar with I/O port logical circuit, not only help to use port correctly and rationally, and will inspire to designing the peripheral logical circuit of one-chip computer to some extent. Load ability and interface of port have certain requirement, because output grade, P0 of mouth and P1 end output, P3 of mouth grade different at structure, so, the load ability and interface of its door demand to have nothing in common with each other. P0 mouth is different from other mouth, its output grade draws the resistance supremely. When using it as the mouth in common use,

output grade is it leak circuit to turn on, is it urge NMOS draw the resistance on taking to be outer with it while inputting to go out to fail. When being used as introduction, should write"1" to a latch first. Every one with P0 mouth can drive 8 Model LS TTL load to export. P1 mouth is an accurate two-way mouth too, used as I/O in common use. Different from P0 mouth output of circuit its, draw load resistance link with power on inside have. In fact, the resistance is that two effects are in charge of FET and together: One FET is in charge of load, its resistance is regular. Another one can is it lead to work with close at two state, make its President resistance value change approximate 0 or group value heavy two situation very. When it is 0 that the resistance is approximate, can draw the pin to the high level fast; when resistance value is very large, P1 mouth high electricity at ordinary times, can is it draw electric current load to offer outwards, draw electric current load to offer outwards, draw the resistance on needn't answer and thinking. Here when the port is used as introduction, must write into 1 to the corresponding latch first too, make FET end relatively about 20,000 ohms because of load resistance in scene and because 40,000 ohms, will not exert an influence on the data that are input. The structure of P2 some mouth is similar to P0 mouth, there are MUX switches. Is it similar to mouth partly to urge, but mouth large a conversion controls some than P1.P3 mouth one multi-functional port, mouth getting many than P1 it have "3 doors and 4 buffers". Two parts there, make her besides accurate two-way function with P1 mouth just, can also use the second function of every pin, "and" door 3

functions one switch in fact, it determines to be to output data of latch to output second signal of function. Act as W=At 1 o'clock, output Q end signal; act as Q=At 1 o'clock, can output W line signal. At the time of programming, it is that the first function is still the second function but needn't have software that set up P3 mouth in advance .It hardware not inside is the automatic to have two function outputted when CPU carries on SFR and seeks the location to visit to P3 mouth/at not lasting lining, there are inside hardware latch Qs=1. The operation principle of P3 mouth is similar to P1 mouth.

Output grade, P3 of mouth, P1 of P1, connect with inside have load resistance of drawing, every one of they can drive 4 Model LS TTL load to output. As while inputting the mouth, any TTL or NMOS circuit can drive P1 of 8051 one-chip computers as P3 mouth in a normal way. Because draw resistance on output grade of them have, can open a way collector too or drain-source resistance is it urge to open a way, do not need to have the resistance of drawing outer. Mouths are all accurate two-way mouths too. When the conduct is input, must write the corresponding port latch with 1 first. As to 80C51 one-chip computer, port can only offer milliampere of output electric currents, is it output mouth go when urging one ordinary basing of transistor to regard as, should contact a resistance among the port and transistor base, in order to the electricity while restraining the high level from exporting P1~P3 Being restored to the throne is the operation of initializing of an one-chip computer. Its main function is to turn PC into

0000H initially, make the one-chip computer begin to hold the conduct procedure from unit 0000H. Except that the ones that enter the system are initialized normally, as because procedure operate it make mistakes or operate there aren't mistake, in order to extricate oneself from a predicament , need to be pressed and restored to the throne the key restarting too. It is an input end which is restored to the throne the signal in 8051 China RST pin. Restore to the throne signal high level effective, should sustain 24 shake cycle (namely 2 machine cycles) the above its effective times. If 6 of frequency of utilization brilliant to shake, restore to the throne signal duration should exceed 4 delicate to finish restoring to the throne and operating. Produce the logic picture of circuit which is restored to the throne the signal: restore to the throne the circuit and include two parts outside in the chip entirely. Outside that circuit produce to restore to the throne signal (RST) hand over to Schmitt's trigger, restore to the throne circuit sample to output , Schmitt of trigger constantly in each S5P2 , machine of cycle in having one more , then just got and restored to the throne and operated the necessary signal inside. Restore to the throne resistance of circuit generally, electric capacity parameter suitable for 6 brilliant to shake, can is it restore to the throne signal high level duration greater than 2 machine cycles to guarantee. Being restored to the throne in the circuit is simple, its function is very important. Pieces of one-chip computer system could normal running, should first check it can restore to the throne not succeeding. Checking and can pop one's head and monitor the pin with the oscilloscope tentatively,

push and is restored to the throne the key, the wave form that observes and has enough range is exported (instantaneous), can also through is it restore to the throne circuit group holding value carry on the experiment to change.

MCS-51系列单片机的功能和结构

MSC-51系列单片机具有一个单芯片电脑的结构和功能，它是英特尔公司的系列产品的名称。这家公司在1976年推出后，引进8位单芯片的MCS-48系列计算机后于1980年推出的8位的MCS-51系列单芯片计算机。诸如此类的单芯片电脑有很多种，如8051，8031，8751，80C51BH,80C31BH 等，其基本组成，基本性能和指令系统都是相同的。8051是51系列单芯片电脑的代表。

一个单芯片的计算机是由以下几个部分组成：（1）一个8位的微处理器（CPU）。（2）片内数据存储器RAM（128B/256B）,它只读/写数据，如结果不在操作过程中，最终结果要显示数据（3）程序存储器ROM/EPROM(4KB/8KB).是用来保存程序一些初步的数据和切片的形式。但一些单芯片电脑没有考虑ROM/EPROM,如8031，8032，80C51等等。（4）4个8路运行的I/O接口，P0，P1，P2，P3，每个接口可以用作入口，也可以用作出口。（5）两个定时/计数器，每个定时方式也可以根据计

算结果或定时控制实现计算机。（6）5个中断（7）一个全双工串行的I/UART（通用异步接收器I口/发送器（UART）），它是实现单芯片电脑或单芯片计算机和计算机的串行通信使用。（８）振荡器和时钟产生电路，需要考虑石英晶体微调能力。允许振荡频率为12MHz，每个上述的部分都是通过内部数据总线连接。其中CPU是一个芯片计算机的核心，它是计算机的指挥中心，是由算术单元和控制器等部分组成。算术单元可以进行８位算术运算和逻辑运算，ALU单元是其中一种运算器，18个存储设备，暂存设备的积累设备进行协调，程序状态寄存器PSW积累了2个输入端的计数等检查暂时作为一个操作往往由人来操作，谁储存1输入的是它使操作去上暂时计数，另有一个操作的结果，回环协调。此外，协调往往是作为对8051内的数据传输转运站考虑。作为一般的微处理器，解码的顺序。振荡器和定时电路等的程序计数器是一个由8个计数器为2，总计16位。这是一个字节的地址，其实程序计数器，是将在个人电脑内进行。从而改变它的内容可以改变它的程序进行。在8051的单芯片电脑的电路，只需要外部石英晶体和频率微调电容，其频率范围为1.2MHz到12MHz。这种脉冲信号，作为8051的工作，即单位时间的最低基本节奏。8051是其他电脑一样，控制的基本工作在于和谐，就像一个管弦乐队，根据击败发挥是指挥。

有光盘（程序存储器，只能读取），并在8051片（数据存储器RAM，可以是可写可读，他们各自独立的内存地址空间，处理办法是，与一般的电脑记忆体相同。8051可8751的程序存储的存储容量4KB的程序切片，地址开始从0000H开始执行，维护的程序和形式不断使用。数据8051-8751的内存数据存储器128B）条8031，地址虚假00FH，中层结果

存入操作使用，数据存储和数据暂时缓冲等。在这128B条内存，有32字节，可以作为工作寄存器使用，这和一般的微处理器是不同的，8051片RAM和登记形式的同一级到安排的位置。这不是很相同，MCS-51系列内存的单芯片计算机和通用计算机为主。通用计算机的第一个地址空间，ROM和RAM,可安排在不同的空间在这个范围内的地址范围，即ROM和RAM 地址的形成与分布在不同的地址空间。在访问内存，相应的，只有一个地址的内存单元，可以用外部存储，也可以内存，并通过访问顺序与此类似。这种内存结构的一种被称为普林斯顿结构。8051记忆分为程序存储器空间和数据存储空间的物理结构上划分，有四个在所有的记忆体空间。在1和数据外部数据存储器和程序存储器空间之一，一组在外面一个内存空间的程序商店，结构这一种形式的程序和数据存储器器件数据存储分开的形式，称为哈佛结构。但是，从用户使用，8051的内存地址空间分为三种：分为（1）片内，（使用16个地址一致的FFFFH，地点为0000H）。（2）64KB的外部数据存储器空间的一个地址，该地址是从0000H 开始执行64KB的FFFFH安排16地址，也到该位置。（3）数据存储器的256B（使用8个地址）的地址空间。上述三个内存空间的地址重叠，区分和设计的8051指令系统中不同的数据传输顺序代码，CPU的访问片，访问RAM块顺序使用MOVX指令外片，内存为访问片。

8051单芯片的电脑有4个8步行并进的I/O端口，分别为P0,P1,P2和P3。每个端口8位的双向口，共占了32针。每一个I/O线可作为独立的入口和出口。每个端口包括一个锁存器，1名入口和一出口引进缓冲区。使数据能锁存输出时，数据缓冲区时，可以引进，但4个通道这些自我相同的功能。系统中的内存片展开外来的，这四个港口可作为准

确的双向的I/O共同使用的输出口。系统的内存中展开外来的片，P2口处于高位，8地址关闭；入口P0口是双向总线，发送地址和8个低数据。

8051单芯片电脑的4个I/O端口是非常巧妙的电路设计。熟悉I/O 端口的逻辑电路，不仅有助于正确和合理利用端口，并在一定程度上将有助于设计周边的单芯片计算机的逻辑电路。在一定程度上负载能力和端口界面有一定的要求，因为输出级和P1口输出端，P3口与P0口结构的不同，因此，负载能力和接口需求互相无太多共同之处。求解P0口是与其他口不同，它的输出级提取阻力。当使用的常用是它的输出级电路泄漏打开，它是利用它敦促采取NMOS管能与它外部的阻力，而输入走出失败。当被用作数据，应该写“1”到内部，每一个P0口与一个可以驱动8型号LS TTL负载出口。P1口是一个准确的双向口，共同使用输出口。不同在P0口输出的电路，得出与负载功率电阻内有联系。事实上，阻力是，两个效果是在场效应管，同负责：一个场效应管的负载负责，它的电阻是正常的。另一条是它可以导致在来两个工作状态密切，使其电阻值变化近似0或2阻值的情况非常严重。当它是0，该阻力是近似的，可以提请较快的高层次，当电阻值是非常大的，P1口以阻碍引进高电平。为P1口输出高电平时，它是可以借鉴的负载提供电流向外，提请电阻无须回答。在这里，当端口作为引进使用，必须首先写入1到相应的锁存，使FET的结束。相对约20000欧姆，因为在现场，负载电阻和40000欧姆，不会产生对输入的数据的影响。一些为P2结构类似于P0口，有MUX的开关。它是类似口部分，大的一个转换控制P1口的多功能端口，获得第一位，这有很多“与”门和4个缓冲。两部分中提供准确的双向功能，还可以使用第二个函数的每一个针“与”门三功能开关，

实际上，它决定将输出数据锁存到输出的函数的第二个信号为W=1点，输出Q端信号。法令：Q=1时，可以输出W线路信号，在制定方案的时候，那就是第一个函数仍是第二个功能，但不必软件预先设置P3口。IT 硬件里面是不是有自动两个函数输出时的CPU进行SFR和要求的位置来访问，在没有至P3口，里面有硬件锁Q报表，P3口的工作原理类似于P1口。

输出级，P1,P3口连接内带的负载电阻的图纸，每一个能驱动4型号LS TTL负载输出1。由于输入口，任何TTL或NMOS电路可以驱动8051的单芯片子在一个正常的方式。因为他们利用输出级阻力，可以打开漏源电阻以敦促打开方式，不需要有阻力。都是准确的双向口。当行为是输入，必须编写相应的锁存器。至于80C51单芯片计算机，端口只能提供输出毫安的电流，是它的输出口去当一个普通的晶体管，要求应与端口之间和晶体管的基极电阻，以电而从出口限制P1~P3被恢复了的高水平，是一个单芯片电脑初始化操作。其主要功能是把最初的PC为0000H，使单芯片电脑开始持有单位0000H开始执行程序的行为。唯一例外的是那些进入系统初始化正常，程序操作，而是因为它犯了错或没有错，为了摆脱自己的困境，需要按下和恢复位的按键重新启动了。这是一个输入端是恢复位，在8051中国RST引脚信号。恢复位的信号还原到高一级的有效值，应维持24倍以上的有效周期。如果是有频率6，恢复位的信号持续时间应超过4微秒完成恢复。设计的电路，恢复位的信号逻辑图：恢复位的电路和芯片包括两个部分外完全。以外的电路产生恢复到施密特触发了位信号（RST),恢复位电路示例输出，施密特不断在每个S5P2,触发机循环，那么就得到了恢复位所需的信号。还原6电阻的

电路一般，电容参数适合，它是可以恢复到较高水平的信号持续时间大于2个机器周期来保证。作为恢复到电路，其功能是非常重要的。一个芯片的计算机系统能够正常运转，应先检查它可不可以恢复。检查可以弹出一个首部和监测与示波器针暂定，推动并恢复位的关键，波形式观察和有足够的范围是出口，也可以通过它使恢复电路进行改变。

英文文献翻译

中等分辨率制备分离的 快速色谱技术 W. Clark Still,* Michael K a h n , and Abhijit Mitra Departm(7nt o/ Chemistry, Columbia Uniuersity,1Veu York, Neu; York 10027 ReceiLied January 26, 1978 我们希望找到一种简单的吸附色谱技术用于有机化合物的常规净化。这种技术是适于传统的有机物大规模制备分离，该技术需使用长柱色谱法。尽管这种技术得到的效果非常好，但是其需要消耗大量的时间，并且由于频带拖尾经常出现低复原率。当分离的样本剂量大于1或者2g时，这些问题显得更加突出。近年来，几种制备系统已经进行了改进，能将分离时间减少到1-3h，并允许各成分的分辨率ΔR f≥（使用薄层色谱分析进行分析）。在这些方法中，在我们的实验室中，媒介压力色谱法1和短柱色谱法2是最成功的。最近，我们发现一种可以将分离速度大幅度提升的技术，可用于反应产物的常规提纯，我们将这种技术称为急骤色谱法。虽然这种技术的分辨率只是中等（ΔR f≥），而且构建这个系统花费非常低，并且能在10-15min内分离重量在的样本。4 急骤色谱法是以空气压力驱动的混合介质压力以及短柱色谱法为基础，专门针对快速分离，介质压力以及短柱色谱已经进行了优化。优化实验是在一组标准条件5下进行的，优化实验使用苯甲醇作为样本，放在一个20mm*5in.的硅胶柱60内，使用Tracor 970紫外检测器监测圆柱的输出。分辨率通过持续时间（r）和峰宽（w,w/2）的比率进行测定的（Figure 1），结果如图2-4所示，图2-4分别放映分辨率随着硅胶颗粒大小、洗脱液流速和样本大小的变化。

外文翻译 - 英文

The smart grid Smart grid is the grid intelligent (electric power), also known as the "grid" 2.0, it is based on the integration, high-speed bidirectional communication network, on the basis of through the use of advanced sensor and measuring technology, advanced equipme nt technology, the advanced control method, and the application of advanced technology of decision support system, realize the power grid reliability, security, economic, efficient, environmental friendly and use the security target, its main features include self-healing, incentives and include user, against attacks, provide meet user requirements of power quality in the 21st century, allow all sorts of different power generation in the form of access, start the electric power market and asset optimizatio n run efficiently. The U.S. department of energy (doe) "the Grid of 2030" : a fully automated power transmission network, able to monitor and control each user and power Grid nodes, guarantee from power plants to end users among all the nodes in the whole process of transmission and distribution of information and energy bi-directional flow. China iot alliance between colleges: smart grid is made up of many parts, can be divided into:intelligent substation, intelligent power distribution network, intelli gent watt-hourmeter,intelligent interactive terminals, intelligent scheduling, smart appliances, intelligent building electricity, smart city power grid, smart power generation system, the new type of energy storage system.Now a part of it to do a simple i ntroduction. European technology BBS: an integration of all users connected to the power grid all the behavior of the power transmission network, to provide sustained and effective economic and security of power. Chinese academy of sciences, institute of electrical: smart grid is including all kinds of power generation equipment, power transmission and distribution network, power equipment and storage equipment, on the basis of the physical power grid will be modern advanced sensor measurement technology, network technology, communication

文献综述,外文翻译,论文网站

文献综述怎么写 1) 什么是文献综述? 文献综述是研究者在其提前阅读过某一主题的文献后，经过理解、整理、融会贯通，综合分析和评价而组成的一种不同于研究论文的文体。 2) 文献综述的写作要求 1、文献综述的格式 文献综述的格式与一般研究性论文的格式有所不同。这是因为研究性的论文注重研究的方法和结果，而文献综述介绍与主题有关的详细资料、动态、进展、展望以及对以上方面的评述。因此文献综述的格式相对多样，但总的来说，一般都包含以下四部分：即前言、主题、总结和参考文献。撰写文献综述时可按这四部分拟写提纲，再根据提纲进行撰写工作。 前言，要用简明扼要的文字说明写作的目的、必要性、有关概念的定义，综述的范围，阐述有关问题的现状和动态，以及目前对主要问题争论的焦点等。前言一般200-300字为宜，不宜超过500字。 正文，是综述的重点，写法上没有固定的格式，只要能较好地表达综合的内容，作者可创造性采用诸多形式。正文主要包括论据和论证两个部分，通过提出问题、分析问题和解决问题，比较不同学者对同一问题的看法及其理论依据，进一步阐明问题的来龙去脉和作者自己的见解。当然，作者也可从问题发生的历史背景、目前现状、发展方向等提出文献的不同观点。正文部分可根据内容的多少可分为若干个小标题分别论述。 小结，是结综述正文部分作扼要的总结，作者应对各种观点进行综合评价，提出自己的看法，指出存在的问题及今后发展的方向和展望。内容单纯的综述也可不写小结。 参考文献，是综述的重要组成部分。一般参考文献的多少可体现作者阅读文献的广度和深度。对综述类论文参考文献的数量不同杂志有不同的要求，一般以30条以内为宜，以最近3-5年内的最新文献为主。 2、文献综述规定 1. 为了使选题报告有较充分的依据，要求硕士研究生在论文开题之前作文献综述。 2. 在文献综述时，研究生应系统地查阅与自己的研究方向有关的国内外文献。通常阅读文献不少于30篇，且文献搜集要客观全面 3. 在文献综述中，研究生应说明自己研究方向的发展历史，前人的主要研究成果，存在的问题及发展趋势等。 4. 文献综述要条理清晰，文字通顺简练。 5. 资料运用恰当、合理。文献引用用方括号[ ]括起来置于引用词的右上角。 6. 文献综述中要有自己的观点和见解。不能混淆作者与文献的观点。鼓励研究生多发现问题、多提出问题、并指出分析、解决问题的可能途径，针对性强。 7. 文献综述不少于3000字。 3、注意事项 ⒈搜集文献应尽量全。掌握全面、大量的文献资料是写好综述的前提，否则，随便搜集一点资料就动手撰写是不可能写出好的综述。 ⒉注意引用文献的代表性、可靠性和科学性。在搜集到的文献中可能出现观点雷同，有的文献在可靠性及科学性方面存在着差异，因此在引用文献时应注意选用代表性、可靠性和科学性较好的文献。 ⒊引用文献要忠实文献内容。由于文献综述有作者自己的评论分析，因此在撰写时应分清作者的观点和文献的内容，不能篡改文献的内容。引用文献不过多。文献综述的作者引用间接文献的现象时有所见。如果综述作者从他人引用的参考文献转引过来，这些文献在他人

计算机网络-外文文献-外文翻译-英文文献-新技术的计算机网络

New technique of the computer network Abstract The 21 century is an ages of the information economy, being the computer network technique of representative techniques this ages, will be at very fast speed develop soon in continuously creatively, and will go deep into the people's work, life and study. Therefore, control this technique and then seem to be more to deliver the importance. Now I mainly introduce the new technique of a few networks in actuality live of application. keywords Internet Network System Digital Certificates Grid Storage 1. Foreword Internet turns 36, still a work in progress Thirty-six years after computer scientists at UCLA linked two bulky computers using a 15-foot gray cable, testing a new way for exchanging data over networks, what would ultimately become the Internet remains a work in progress. University researchers are experimenting with ways to increase its capacity and speed. Programmers are trying to imbue Web pages with intelligence. And work is underway to re-engineer the network to reduce Spam (junk mail) and security troubles. All the while threats loom: Critics warn that commercial, legal and political pressures could hinder the types of innovations that made the Internet what it is today. Stephen Crocker and Vinton Cerf were among the graduate students who joined UCLA professor Len Klein rock in an engineering lab on Sept. 2, 1969, as bits of meaningless test data flowed silently between the two computers. By January, three other "nodes" joined the fledgling network.

外文翻译computerprogram英文.doc

Computer Program 1 Introduction Computer Program, set of instructions that directs a computer to perform someprocessing function or combination of functions. For the instructions to be carried out, a computer must execute a program, that is, the computer reads the program, and then follow the steps encoded in the program in a precise order until completion. A program can be executed many different times, with each execution yielding a potentially different result depending upon the options and data that the user gives the computer. Programs fall into two major classes: application programs and operating systems. An application program is one that carries out somefunction directly for a user, such as word processing or game-playing. An operating system is a program that manages the computer and the various resources and devices connected to it, such as RAM,hard drives, monitors, keyboards, printers, and modems,so that they maybe used by other programs. Examples of operating systems are DOS, Windows 95, OS\2, and UNIX. 2 Program Development Software designers create new programs by using special applications programs, often called utility programs or development programs. A programmer uses another type of program called a text editor to write the new program in a special notation called a programming language. With the text editor, the programmer creates a text file, which is an ordered list of instructions, also called the program source file. The individual instructions that make up the program source file are called source code. At this point, a special applications program translates the source code into machine language, or object code— a format that the operating system

机械设计外文翻译(中英文)

机械设计理论 机械设计是一门通过设计新产品或者改进老产品来满足人类需求的应用技术科学。它涉及工程技术的各个领域，主要研究产品的尺寸、形状和详细结构的基本构思，还要研究产品在制造、销售和使用等方面的问题。 进行各种机械设计工作的人员通常被称为设计人员或者机械设计工程师。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。如前所诉，机械设计的目的是生产能够满足人类需求的产品。发明、发现和科技知识本身并不一定能给人类带来好处，只有当它们被应用在产品上才能产生效益。因而，应该认识到在一个特定的产品进行设计之前，必须先确定人们是否需要这种产品。 应当把机械设计看成是机械设计人员运用创造性的才能进行产品设计、系统分析和制定产品的制造工艺学的一个良机。掌握工程基础知识要比熟记一些数据和公式更为重要。仅仅使用数据和公式是不足以在一个好的设计中做出所需的全部决定的。另一方面，应该认真精确的进行所有运算。例如，即使将一个小数点的位置放错，也会使正确的设计变成错误的。 一个好的设计人员应该勇于提出新的想法，而且愿意承担一定的风险，当新的方法不适用时，就使用原来的方法。因此，设计人员必须要有耐心，因为所花费的时间和努力并不能保证带来成功。一个全新的设计，要求屏弃许多陈旧的，为人们所熟知的方法。由于许多人墨守成规，这样做并不是一件容易的事。一位机械设计师应该不断地探索改进现有的产品的方法，在此过程中应该认真选择原有的、经过验证的设计原理，将其与未经过验证的新观念结合起来。 新设计本身会有许多缺陷和未能预料的问题发生，只有当这些缺陷和问题被解决之后，才能体现出新产品的优越性。因此，一个性能优越的产品诞生的同时，也伴随着较高的风险。应该强调的是，如果设计本身不要求采用全新的方法，就没有必要仅仅为了变革的目的而采用新方法。 在设计的初始阶段，应该允许设计人员充分发挥创造性，不受各种约束。即使产生了许多不切实际的想法，也会在设计的早期，即绘制图纸之前被改正掉。只有这样，才不致于堵塞创新的思路。通常，要提出几套设计方案，然后加以比较。很有可能在最后选定的方案中，采用了某些未被接受的方案中的一些想法。

变电站_外文翻译_外文文献_英文文献_变电站的综合概述

英文翻译 A comprehensive overview of substations Along with the economic development and the modern industry developments of quick rising, the design of the power supply system become more and more completely and system. Because the quickly increase electricity of factories, it also increases seriously to the dependable index of the economic condition, power supply in quantity. Therefore they need the higher and more perfect request to the power supply. Whether Design reasonable, not only affect directly the base investment and circulate the expenses with have the metal depletion in colour metal, but also will reflect the dependable in power supply and the safe in many facts. In a word, it is close with the economic performance and the safety of the people. The substation is an importance part of the electric power system, it is consisted of the electric appliances equipments and the Transmission and the Distribution. It obtains the electric power from the electric power system, through its function of transformation and assign, transport and safety. Then transport the power to every place with safe, dependable, and economical. As an important part of power’s transport and control, the transformer substation must change the mode of the traditional design and control, then can adapt to the modern electric power system, the development of modern industry and the of trend of the society life. Electric power industry is one of the foundations of national industry and national economic development to industry, it is a coal, oil, natural gas, hydropower, nuclear power, wind power and other energy conversion into electrical energy of the secondary energy industry, it for the other departments of the national economy fast and stable development of the provision of adequate power, and its level of development is a reflection of the country's economic development an important indicator of the level. As the power in the industry and the importance of the national economy, electricity transmission and distribution of electric energy used in these areas is an indispensable component.。Therefore, power transmission and distribution is critical. Substation is to enable superior power plant power plants or power after adjustments to the lower load of books is an important part of power transmission. Operation of its functions, the capacity of a direct impact on the size of the lower load power, thereby affecting the industrial production and power consumption.Substation system if a link failure, the system will protect the part of action. May result in power outages and so on, to the production and living a great disadvantage. Therefore, the substation in the electric power system for the protection of electricity reliability,

机械专业外文翻译(中英文翻译)

外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important considerations in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems covering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11-and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are

员工激励的文献综述、外文翻译.doc

一、激励理论的背景 在经济发展的过程中,劳动分工与交易的出现带来了激励问题。激励理论是行为科学中用于处理需要，动机，目标和行为四者之间关系的核心理论。行为科学认为人的动机来自需要，由需要确定人们的行为目标，激励则作用于人内心活动，激发，驱动和强化人的行为。哈佛大学维廉詹姆士研究表明：在没有激励措施下,下属一般仅能发挥工作能力的20%～30%，而当他受到激励后,其工作能力可以提升到80%～90%，所发挥的作用相当于激励前的3到4倍。日本丰田公司采取激励措施鼓励员工提建议，结果仅1983年一年，员工提了165万条建议，平均每人31条，它为公司带来900亿日元利润，相当于当年总利润的18%。由于激励的效果明显，所以各种组织为了提高生产效率，有些专家学者就开始了对激励理论的研究之中，探索激励的无穷潜力。 二、国外研究现状 国外对于激励理论有了大量的研究并获得了丰硕的成果。总体来说，可以分为两类激励理论。一类是以人的心理需求和动机为主要研究对象的激励理论，熟称“内容型激励理论”。另一类是以人的心理过程和行为过程相互作用的动态系统为研究对象的激励过程理论,它也被称作是“行为型激励理论”。 1 内容型激励理论 1.1 奠瑞的人类人格理论 这种理论认为，在面临着动态且不断变化的环境时，人们都是自适应的。它把需求分成了两种类型，即生理需求和心理需求。前者与人体基本生理过程的满足感有关，而后者所关注的是情绪上和精神上的满足感。 1.2 马斯洛的“需要层次”理论 美国心理学家马斯洛(A.H.Maslow)进一步发展了莫瑞的研究，在1954年出版的《动机与人格》一书中对该理论作了进一步的阐释。马斯洛认为人的需要可以划分为五个层次，从低到高依次为生理需要，安全需要，社交需要，尊熏需要，自我实现需要，且这五个层次的顺序，对每个人都是相同的。只有当较低层次的需要获得了基本满足后，下一个较高层次的需要才能成为主导需要。 1.3 赫茨伯格的激励—保健双因素理论 美国心理学家赫茨伯格因素理论打破了这一假设。他于1959年在《工作的激励》一书中提出了保健——激励因素理论，简称双因素理论。即保健因素和激励因素。保健因素可以用来体现高水平员工的不满意，激励因素可以用来体现高水平员工的满意度。他认为只有激励因素才能促发员工积极性,提高生产效率。 2 行为型激励理论 2.1 洛克的目标设置理论 2O世纪6O年代末，埃德温·A·洛克和他的同事们花了许多年的时间研究目标对于人类行为和绩效的效果。他们的研究导致了目标设置理论的创立并不断地得到验证，提出：指向一共同目标的工作意向是工作效率的主要源泉。他还提出了具体的设置目标的步骤。 2.2 亚当斯的公平理论 美国心理学家亚当斯(J.s.Adams)对员工受激励程度的大小与他人之间的关系进行研究，并在《工人关于工资不公平的内心冲突同其生产率的关系》(1962年与罗森合写)，《工

博物馆 外文翻译 外文文献 英文文献

第一篇： 航空博物馆与航空展示公园 巴特罗米耶杰·基谢列夫斯基 飞翔的概念、场所的精神、老机场的建筑---克拉科夫新航空博物馆理性地吸取了这些元素，并将它们整合到一座建筑当中。Rakowice-Czyzyny机场之前的旧飞机修理库为新建筑的平面和高度设定了模数比例。在此基本形态上进一步发展，如同裁切和折叠一架纸飞机，生成了一座巨大的建筑。其三角形机翼是由混凝土制成，却如同风动螺旋桨一样轻盈。这个机翼宽大通透，向各个方向开敞。它们的形态与组织都是依据内部功能来设计的。机翼部分为3个不平衡的平面，使内外景观在不断变化中形成空间的延续性，并且联系了建筑内的视觉焦点和室外的展览区。 新航空展示公园的设计连接了博物馆的8栋建筑和户外展览区，并与历史体验建立联系。从前的视觉轴线与通道得到尊重，旧的道路得到了完善，朝向飞机场和跑道的空间被限定出来。每栋建筑展示了一个主题或是一段飞行史。建筑周围伸展出巨大的平台，为特殊主题的室外展览提供了空间。博物馆容纳了超过150架飞机、引擎、飞行复制品、成套的技术档案和历史图片。这里的特色收藏是飞机起源开始的各种飞行器，如Jatho1903、Grade1909、莱特兄弟1909年的飞机模型和1911年的鸽式单翼机。 The first passage: Museum for aviation and aviation exhibition park Bartiomiej Kislelewski The idea of flying, the spirit of place, the structure of the historic airfield – the new Museum of Aviation in Krakow takes up these references intellectually and synthesizes them into a building. The old hangars of the former airport Rakowice Czyzyny set the modular scale for the footprint and the height of the new building. Developed from this basic shape, as if cut out and folded like a paper airplane, a large structure has been generated, with triangular wings made of concrete and yet as light as a wind-vane propeller. The wings are generously glazed and open in all directions. Their form and arrangement depend on the interior uses. In the floor plans of the wings, the three offset

机械设计外文翻译(中英文)

盛年不重来，一日难再晨。及时宜自勉，岁月不待人。 机械设计理论 机械设计是一门通过设计新产品或者改进老产品来满足人类需求的应用技术科学。它涉及工程技术的各个领域，主要研究产品的尺寸、形状和详细结构的基本构思，还要研究产品在制造、销售和使用等方面的问题。 进行各种机械设计工作的人员通常被称为设计人员或者机械设计工程师。机械设计是一项创造性的工作。设计工程师不仅在工作上要有创造性，还必须在机械制图、运动学、工程材料、材料力学和机械制造工艺学等方面具有深厚的基础知识。如前所诉，机械设计的目的是生产能够满足人类需求的产品。发明、发现和科技知识本身并不一定能给人类带来好处，只有当它们被应用在产品上才能产生效益。因而，应该认识到在一个特定的产品进行设计之前，必须先确定人们是否需要这种产品。 应当把机械设计看成是机械设计人员运用创造性的才能进行产品设计、系统分析和制定产品的制造工艺学的一个良机。掌握工程基础知识要比熟记一些数据和公式更为重要。仅仅使用数据和公式是不足以在一个好的设计中做出所需的全部决定的。另一方面，应该认真精确的进行所有运算。例如，即使将一个小数点的位置放错，也会使正确的设计变成错误的。 一个好的设计人员应该勇于提出新的想法，而且愿意承担一定的风险，当新的方法不适用时，就使用原来的方法。因此，设计人员必须要有耐心，因为所花费的时间和努力并不能保证带来成功。一个全新的设计，要求屏弃许多陈旧的，为人们所熟知的方法。由于许多人墨守成规，这样做并不是一件容易的事。一位机械设计师应该不断地探索改进现有的产品的方法，在此过程中应该认真选择原有的、经过验证的设计原理，将其与未经过验证的新观念结合起来。 新设计本身会有许多缺陷和未能预料的问题发生，只有当这些缺陷和问题被解决之后，才能体现出新产品的优越性。因此，一个性能优越的产品诞生的同时，也伴随着较高的风险。应该强调的是，如果设计本身不要求采用全新的方法，就没有必要仅仅为了变革的目的而采用新方法。 在设计的初始阶段，应该允许设计人员充分发挥创造性，不受各种约束。即使产生了许多不切实际的想法，也会在设计的早期，即绘制图纸之前被改正掉。只有这样，才不致于堵塞创新的思路。通常，要提出几套设计方案，然后加以比较。很有可能在最后选定的方案中，采用了某些未被接受的方案中的一些想法。

大数据外文翻译参考文献综述

大数据外文翻译参考文献综述 (文档含中英文对照即英文原文和中文翻译) 原文： Data Mining and Data Publishing Data mining is the extraction of vast interesting patterns or knowledge from huge amount of data. The initial idea of privacy-preserving data mining PPDM was to extend traditional data mining techniques to work with the data modified to mask sensitive information. The key issues were how to modify the data and how to recover the data mining result from the modified data. Privacy-preserving data mining considers the problem of running data mining algorithms on confidential data that is not supposed to be revealed even to the party

running the algorithm. In contrast, privacy-preserving data publishing (PPDP) may not necessarily be tied to a specific data mining task, and the data mining task may be unknown at the time of data publishing. PPDP studies how to transform raw data into a version that is immunized against privacy attacks but that still supports effective data mining tasks. Privacy-preserving for both data mining (PPDM) and data publishing (PPDP) has become increasingly popular because it allows sharing of privacy sensitive data for analysis purposes. One well studied approach is the k-anonymity model [1] which in turn led to other models such as confidence bounding, l-diversity, t-closeness, (α,k)-anonymity, etc. In particular, all known mechanisms try to minimize information loss and such an attempt provides a loophole for attacks. The aim of this paper is to present a survey for most of the common attacks techniques for anonymization-based PPDM & PPDP and explain their effects on Data Privacy. Although data mining is potentially useful, many data holders are reluctant to provide their data for data mining for the fear of violating individual privacy. In recent years, study has been made to ensure that the sensitive information of individuals cannot be identified easily. Anonymity Models, k-anonymization techniques have been the focus of intense research in the last few years. In order to ensure anonymization of data while at the same time minimizing the information