模具术语英文翻译

模具术语英文翻译

根据国家标准，以下为部分塑料模具成形术语的标准翻译。

动模 Movable Mould Moving Half

定模座板 Fixed Clamp Plate Top Clamping Plate Top Plate

动模座板 Moving Clamp Plate Bottom Clamping Plate Bottom Plate 上模座板 Upper Clamping Plate

下模座板 Lower Clamping Plate

凹模固定板 Cavity-retainer Plate

型芯固定板 Mould Core-retainer Plate

凸模固定板 Punch-retainer Plate

模套 Die Body Die Sleeve Die Blank

支承板 Backing Plate Support Plate

垫块 Spacer Parallel

支架 Ejector Housing Mould Base Leg

模头 Die Head

根据国家标准，以下为部分压铸模具术语的标准翻译。

压力铸造模具 Die-Casting Die

压铸模零部件

定模 Fixed Die Cover Die

定模座板 Fixed Clamping Plate

定模套板 Bolster Fixed Die

动模 Moving Die Ejector Die

动模座板 Moving Clamping Plate

直流道 Sprue

横流道 Runner

内浇口 Gate

模具分类

Injection Mold 注塑模

Plastic Rubber Mould 塑胶模

Rubber Molding 橡胶成形

Hot Chamber Die Casting 热室压铸

Sand Mold Casting 砂模铸造

Extrusion Mold 挤出模

Multi-Cavity Mold 多模穴模具

Stack Mold, Stack Injection Mould 叠层模

Plaster Mold 石膏模

Three Plates Mold 三板模

Plain Die 简易模

Pierce Die 冲孔模

Forming Die 成型模

Progressive Die 连续模

Gang Dies 复合模

Shearing Die 剪边模

Cavity Die 型腔模

Riveting Die 铆合模

Compression Molding 压缩成型

Flash Mold 溢流式模具

Extrusion Mold 挤压式模具

Split Mold 分割式模具

Mould Cavity 型腔母模

Mold Core 模芯公模

Large Die Mold 大型模具

Precise Die Mold 精密模具

Complex Die Mold 复杂模具

Foaming Mould 发泡模具

Metal Die 金属模具

Plastic Mold 塑料模具

Press Tool Stamping Die Punch Die 冲压模具Extrusion Die 挤压模具

Graphite Die 石墨模具

流道浇口部分

Runner System 浇道系统

Sprue Cold Material Trap 浇道冷料井Sprue Puller 拉杆

Runner Design 流道设计

Main Runner 主流道

Secondary Runner 次流道

Mould Gate Design 浇口设计

Submarine Gate 潜伏浇口

Tunnel Gate 隧道式浇口

Pinpoint Gate 点浇口

Fan Gate 扇形浇口

Side Gate 侧浇口

Edge Gate 侧缘浇口

Tab Gate 搭接浇口

Film Gate 薄膜浇口

Flash Gate 闸门浇口

Slit Gate 缝隙浇口

Dish Gate 盘形浇口

Diaphragm Gate 隔膜浇口

Ring Gate 环形浇口

Runnerless 无浇道

Sprueless 无射料管方式

Long Nozzle 延长喷嘴方式

Sprue 浇口，溶渣

Insulated Runner Hot Runner 热浇道

Runner Plat 浇道模块

Valve Gate阀门浇口

Slag Well 冷料井

Cold Slag 冷料渣

Sprue Gate 射料浇口，直浇口

Nozzle 射嘴

Sprue Lock Pin 料头钩销（拉料杆）

注塑缺陷

Flash 飞边

Warpage 翘曲

Air Trap 积风

Blush 发赤

Flow Line 流痕

Splay 银纹

Short Shot 短射

Sink Mark 缩痕

模具专业英文术语大全

模具英语专业术语 模具述语 一、入水：gate 进入位： gate location 水口形式：gate type 大水口：edge gate 细水口： pin-point gate 水口大小：gate size 转水口： switching runner/gate 唧嘴口径： sprue diameter 二、流道: runner 热流道： hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形流道：round(full/half runner 流道电脑分析：mold flow analysis 流道平衡:runner balance 热嘴： hot sprue 热流道板：hot manifold 发热管：cartridge heater 探针: thermocouples 插头： connector plug 插座： connector socket 密封/封料： seal 三、运水：water line 喉塞：line lpug 喉管：tube 塑胶管：plastic tube 快速接头：jiffy quick connector plug/socker 四、模具零件： mold components 三板模：3-plate mold 二板模：2-plate mold 边钉/导边：leader pin/guide pin 边司/导套：bushing/guide bushing 中托司：shoulder guide bushing 中托边L：guide pin 顶针板：ejector retainner plate 托板： support plate 螺丝： screw 管钉：dowel pin 开模槽：ply bar scot 内模管位：core/cavity inter-lock 顶针： ejector pin 司筒：ejector sleeve 司筒针：ejector pin 推板：stripper plate 缩呵：movable core,return core core puller 扣机（尼龙拉勾）：nylon latch lock 斜顶：lifter 模胚（架）： mold base 上内模：cavity insert 下内模：core insert 行位（滑块）： slide 镶件：insert 压座/斜鸡：wedge 耐磨板/油板：wedge wear plate 压条：plate 撑头: support pillar 唧嘴： sprue bushing 挡板：stop plate 定位圈：locating ring 锁扣：latch 扣鸡：parting lock set 推杆：push bar 栓打螺丝：S.H.S.B 顶板：eracuretun 活动臂：lever arm 分流锥：spure sperader 水口司:bush 垃圾钉：stop pin 隔片：buffle 弹弓柱：spring rod 弹弓:die spring 中托司：ejector guide bush 中托边：ejector guide pin 镶针：pin 销子：dowel pin 波子弹弓：ball catch 喉塞: pipe plug

塑料模具发展中英文对照外文翻译文献

中英文对照外文翻译文献 (文档含英文原文和中文翻译) 外文： The development of plastic mould China's industrial plastic moulds from the start to now, after more than half a century, there has been great development, mold levels have been greatly enhanced. Mould has been at large can produce 48-inch big-screen color TV Molded Case injection mold, 6.5 kg capacity washing machine full of plastic molds, as well as the overall car bumpers and dashboards, and other plastic mould precision plastic molds, the camera is capable of producing plastic mould , multi-cavity mold small modulus gear and molding mold. --Such as Tianjin and Yantai days

Electrical Co., Ltd Polaris IK Co. manufactured multi-cavity mold VCD and DVD gear, the gear production of such size precision plastic parts, coaxial, beating requirements have reached a similar foreign the level of product, but also the application of the latest gear design software to correct contraction as a result of the molding profile error to the standard involute requirements. Production can only 0.08 mm thickness of a two-cavity mold and the air Cup difficulty of plastic doors and windows out of high modulus, and so on. Model cavity injection molding manufacturing accuracy of 0.02 to 0.05 mm, surface roughness Ra0.2 μ m, mold quality, and significantly increase life expectancy, non-hardening steel mould life up to 10~ 30 million, hardening steel form up to 50 ~ 10 million times, shorten the delivery time than before, but still higher than abroad,and the gap between a specific data table. Process, the multi-material plastic molding die, efficient multicolor injection mould, inserts exchange structure and core pulling Stripping the innovative design has also made great progress. Gas-assisted injection molding, the use of more mature technologies, such as Qingdao Hisense Co., Ltd., Tianjin factorycommunications and broadcasting companies, such as moldmanufacturers succeeded in 29 ~ 34-inch TV thick-walled shell, as well as some parts on the use of gas-assisted mould technology Some manufacturers also use the C-MOLD gas-assisted software and achieved better results. Prescott, such as Shanghai, such as the new

冲压模具专业词汇中英文翻译

Counter bored hole 沉孔 Chamfer 倒斜角 Fillet 倒圆角 padding block垫块 stepping bar垫条 upper die base上模座 lower die base下模座 upper supporting blank上承板 upper padding plate blank上垫板 spare dies模具备品 spring 弹簧 bolt螺栓 document folder活页夹 file folder资料夹 to put file in order整理资料 spare tools location手工备品仓 first count初盘人 first check初盘复棹人 second count 复盘人 second check复盘复核人 equipment设备 waste materials废料 work in progress product在制品 casing = containerization装箱 quantity of physical inventory second count 复盘点数量 Quantity of customs count 会计师盘,点数量 the first page第一联 filed by accounting department for reference会计部存查 end-user/using unit(department)使用单位 Summary of year-end physical inventory bills 年终盘点截止单据汇总表 bill name单据名称 This sheet and physical inventory list will be sent to accounting department together (Those of NHK will be sent to financial department) 本表请与盘点清册一起送会计部－(NHK厂区送财会部) Application status records of year-end physical inventory List and physical inventory card 年终盘点卡与清册使用－状况明细表 blank and waste sheet NO. 空白与作废单号

机械专业术语英文翻译

陶瓷 ceramics 合成纤维 synthetic fibre 电化学腐蚀 electrochemical corrosion 车架 automotive chassis 悬架 suspension 转向器 redirector 变速器 speed changer 板料冲压 sheet metal parts 孔加工 spot facing machining 车间 workshop 工程技术人员 engineer 气动夹紧 pneuma lock 数学模型 mathematical model 画法几何 descriptive geometry 机械制图 Mechanical drawing 投影 projection 视图 view 剖视图 profile chart 标准件 standard component 零件图 part drawing 装配图 assembly drawing 尺寸标注 size marking

技术要求 technical requirements 刚度 rigidity 内力 internal force 位移 displacement 截面 section 疲劳极限 fatigue limit 断裂 fracture 塑性变形 plastic distortion 脆性材料 brittleness material 刚度准则 rigidity criterion 垫圈 washer 垫片 spacer 直齿圆柱齿轮 straight toothed spur gear 斜齿圆柱齿轮 helical-spur gear 直齿锥齿轮 straight bevel gear 运动简图 kinematic sketch 齿轮齿条 pinion and rack 蜗杆蜗轮 worm and worm gear 虚约束 passive constraint 曲柄 crank 摇杆 racker 凸轮 cams

模具英语100句

如何用英文和老外检讨模具 (2008-1-16 08:50) 1．XXX！你现在有空吗，我可以问你一些问题吗？ Could I ask you some questions？May I ask you some questions (a question)? 2．请问此产品的面是否为外观面？表面做什么处理？是晒纹/抛光？ Can you tell me whether the surface of this part is a visible/esthetic one? What will we do for its surface? Texture or Polishing? 3．请问产品这个面可否加顶针或顶块？产品允许加扁顶针吗？ Does this part need an ejector pin or an ejector bar? Can we add an ejector blade? 4．这个产品的柱位我们打算做司筒。（或镶针）可以吗？ Can we add ejector sleeves or ejector pins in the boss of this part? 5．产品的这个位置有倒扣不能出模，我们打算做行位，在此面上会有分模线，你接受吗？There's an undercut at this position that can not be molded, we plan to make a slider for it. It will also have a parting line on this side, is that OK? 6．产品里面的这个位置我们打算做斜顶或内行位，有问题吗？ We will make the lifter and (inner) slider in this position, will that be a problem? 7．你提供的2D产品图与3D产品图不一致，请问以哪一个图面为准？ The 2D and 3D drawings you provided are not the same, could you advise which one is correct? 8．你提供的3D产品图有的地方没有出模角，有的地方胶位太厚，有的地方胶位太溥，这些产品问题我们可以自己修改吗？修改后会给交给你确认。 There is no draft angle in the 3D model, some areas are too thick, and some are too thin. Can we modify them by ourselves? We will send you the updated drawing for approval. 9．按你们提供的缩水率千分之五，这个模具的尺寸已经做到了模具图面要求。但注塑出来的产品不符合你们的产品图。请确认你们的材料的缩水率是否正确？ According to the shrinkage rate .005”, the mold has been done in the right dimension, but the part falls short to your part print(the actual dimensions are out of tolerances), are you sure the shrinkage is right?

机械专业外文翻译中英文翻译

外文翻译 英文原文 Belt Conveying Systems Development of driving system Among the methods of material conveying employed，belt conveyors play a very important part in the reliable carrying of material over long distances at competitive cost．Conveyor systems have become larger and more complex and drive systems have also been going through a process of evolution and will continue to do so．Nowadays，bigger belts require more power and have brought the need for larger individual drives as well as multiple drives such as 3 drives of 750 kW for one belt(this is the case for the conveyor drives in Chengzhuang Mine)．The ability to control drive acceleration torque is critical to belt conveyors’ performance．An efficient drive system should be able to provide smooth，soft starts while maintaining belt tensions within the specified safe limits．For load sharing on multiple drives．torque and speed control are also important consideratio ns in the drive system’s design. Due to the advances in conveyor drive control technology，at present many more reliable．Cost-effective and performance-driven conveyor drive systems cov ering a wide range of power are available for customers’ choices[1]. 1 Analysis on conveyor drive technologies 1．1 Direct drives Full-voltage starters．With a full-voltage starter design，the conveyor head shaft is direct-coupled to the motor through the gear drive．Direct full-voltage starters are adequate for relatively low-power, simple-profile conveyors．With direct fu11-voltage starters．no control is provided for various conveyor loads and．depending on the ratio between fu11- and no-1oad power requirements，empty starting times can be three or four times faster than full load．The maintenance-free starting system is simple，low-cost and very reliable．However, they cannot control starting torque and maximum stall torque；therefore．they are

冲压模具技术外文翻译(含外文文献)

前言 在目前激烈的市场竞争中，产品投入市场的迟早往往是成败的关键。模具是高质量、高效率的产品生产工具，模具开发周期占整个产品开发周期的主要部分。因此客户对模具开发周期要求越来越短，不少客户把模具的交货期放在第一位置，然后才是质量和价格。因此，如何在保证质量、控制成本的前提下加工模具是值得认真考虑的问题。模具加工工艺是一项先进的制造工艺，已成为重要发展方向，在航空航天、汽车、机械等各行业得到越来越广泛的应用。模具加工技术，可以提高制造业的综合效益和竞争力。研究和建立模具工艺数据库，为生产企业提供迫切需要的高速切削加工数据，对推广高速切削加工技术具有非常重要的意义。本文的主要目标就是构建一个冲压模具工艺过程，将模具制造企业在实际生产中结合刀具、工件、机床与企业自身的实际情况积累得高速切削加工实例、工艺参数和经验等数据有选择地存储到高速切削数据库中，不但可以节省大量的人力、物力、财力，而且可以指导高速加工生产实践，达到提高加工效率，降低刀具费用，获得更高的经济效益。 1.冲压的概念、特点及应用 冲压是利用安装在冲压设备（主要是压力机）上的模具对材料施加压力，使其产生分离或塑性变形，从而获得所需零件（俗称冲压或冲压件）的一种压力加工方法。冲压通常是在常温下对材料进行冷变形加工，且主要采用板料来加工成所需零件，所以也叫冷冲压或板料冲压。冲压是材料压力加工或塑性加工的主要方法之一，隶属于材料成型工程术。 冲压所使用的模具称为冲压模具，简称冲模。冲模是将材料（金属或非金属）批量加工成所需冲件的专用工具。冲模在冲压中至关重要，没有符合要求的冲模，批量冲压生产就难以进行；没有先进的冲模，先进的冲压工艺就无法实现。冲压工艺与模具、冲压设备和冲压材料构成冲压加工的三要素，只有它们相互结合才能得出冲压件。 与机械加工及塑性加工的其它方法相比，冲压加工无论在技术方面还是经济方面都具有许多独特的优点，主要表现如下； (1) 冲压加工的生产效率高，且操作方便，易于实现机械化与自动化。这是

机械术语英文翻译

机械术语英文翻译 阿基米德蜗杆Archimedes worm 安全系数safety factor; factor of safety安全载荷safe load 凹面、凹度concavity扳手wrench 板簧flat leaf spring 半圆键woodruff key 变形deformation摆杆oscillating bar 摆动从动件oscillating follower 摆动从动件凸轮机构cam with oscillating follower 摆动导杆机构oscillating guide-bar mechanism 摆线齿轮cycloidal gear摆线齿形cycloidal tooth profile 摆线运动规律cycloidal motion 摆线针轮cycloidal-pin wheel包角angle of contact 保持架cage背对背安装丨back-to-back arrangement 背锥back cone ；normal cone 背锥角back angle背锥距back cone distance比例尺scale 热容specific heat capacity 闭式链closed kinematic chain闭链机构closed chain mechanism 臂部arm 变频器frequency converters变频调速frequency control of motor speed 变速speed change 变速齿轮change gear ; change wheel变位齿轮modified gear变位系数modification coefficient 标准齿轮standard gear标准直齿轮standard spur gear 表面质量系数superficial mass factor 表面传热系数surface coefficient of heat transfer 表面粗糙度surface roughness 并联式组合combination in parallel并联机构parallel mechanism 并联组合机构parallel combined mechanism并行工程concurrent engineering 并行设计concurred design, CD不平衡相位phase angle of unbalance 不平衡imbalance (or unbalance)不平衡量amount of unbalance 不完全齿轮机构intermittent gearing波发生器wave generator 波数number of waves补偿compensation 参数化设计parameterization design, PD残余应力residual stress 操纵及控制装置operation control device槽轮Geneva wheel 槽轮机构Geneva mechanism ；Maltese cross槽数Geneva numerate 槽凸轮groove cam侧隙backlash 差动轮系differential gear train差动螺旋机构differential screw mechanism 差速器differential常用机构conventional mechanism; mechanism in common use 车床lathe承载量系数bearing capacity factor 承载能力bearing capacity成对安装paired mounting 尺寸系列dimension series齿槽tooth space 齿槽宽spacewidth齿侧间隙backlash 齿顶高addendum齿顶圆addendum circle 齿根高dedendum齿根圆dedendum circle 齿厚tooth thickness齿距circular pitch 齿宽face width齿廓tooth profile 齿廓曲线tooth curve齿轮gear 齿轮变速箱speed-changing gear boxes齿轮齿条机构pinion and rack 齿轮插刀pinion cutter; pinion-shaped shaper cutter齿轮滚刀hob ,hobbing cutter 齿轮机构gear齿轮轮坯blank 齿轮传动系pinion unit齿轮联轴器gear coupling 齿条传动rack gear齿数tooth number 齿数比gear ratio齿条rack 齿条插刀rack cutter; rack-shaped shaper cutter齿形链、无声链silent chain 齿形系数form factor齿式棘轮机构tooth ratchet mechanism 插齿机gear shaper重合点coincident points 重合度contact ratio冲床punch

模具DFM常用中英文对照

DFM常用中英文对照 1、这个红色面在前模方向/后模方向/行位方向有倒扣。 This red surface is undercut at cavity side / core side / slider side. 2、这些红色面在前模方向/后模方向/行位方向有倒扣。 These red surfaces are undercut at cavity side / core side / slider side. 3、产品的这个位置太小，导致模具在前模方向/后模方向/行位方向有薄钢位。 This position is too small and it will bring the thin steel at cavity side / core side / slider side. 4、这些红色线是前后模/镶件/行位/斜顶分型线。 These red lines are the parting line of cavity and core / insert / slider / lifter. 5、此产品使用推板/推块顶出。 Use the stripper plate / ejector block to eject this part. 6、前模/后模斜内行位。 Inner angle slider at cavity / core side. 7、为了简化模具结构建议改变此处出模方向。 Suggest to change the draft direction of this position to make the mold structure simply. 8、最终的进胶位置根据模流分析。 Finally gate position according the mold flow analysis. 9、斜顶与后面的柱位空间太小，斜顶在运动时会干涉到柱子，请考虑移动这个柱子的位置。 This lifter intervene with the pole during ejection, please consider changing the position of the pole. 10、此处有薄钢位，强度不足而且不容易冷却。 The strength of this area is too weak and it is hard to cool because the thin steel. 11、此处有尖角，填充困难。 It is hard to fill for this area because the sharp feature. 12、此处料位太厚，会有缩水，建议减胶改善。 We suggest to reduce some wall thickness to avoid the sink mark for this position. 13、此处的行位夹线在外观面上，请确认是否接受？ Please confirm whether it is acceptable to have a slider line on the visible surface? 14、建议加大拔模角，以便脱模顺利。 We suggest to enlarge the draft angle to help release the tool. 15、如果分型面此处，模具上会有尖角和刀口，对模具寿命有影响。 There are sharp edges if we set the parting line here, it will reduce the tool life. 16、此处料厚段差很大，成品表面会有应力痕，建议修改如图示。 The thickness is not equal and it will bring the stress lines on the surface, suggest to improve the part as the picture shown. 17、此大行位上有小行位，开模时小行位需先退，大行位做延时，合模时则相反。 The small slider is inside the big slider, when the mold open, the small slider need to recede first and the big slider have to postpone. When the mold close, it is contrary. 18、此处需做强顶。 This position need to force ejection. 19、由于此处没有足够空间下热咀，所以需做一个柱子进胶。 This position need to make a pole for gating because there have no enough space for hot sprue. 20、沾模， stick

模具术语翻译

模具名词中英文对照表序号中文名英文名 1一、水口gate 2进水位gate location 3水口形式gate type 4大水口edge gate 5细水口pin-point gate 6水口大小gate size 7转水口switching gate 8唧嘴口径sprue diameter 9二、流道runner 10热流道hot runner 11冷流道cold runner 12唧嘴直流direct sprue gate 13圆形流道round runner 14模流分析mold flow analysis 15流道平衡runner balance 16热嘴hot sprue 17热流道板hot manifold 18发热管cartridge heater 19探针thermocouples 20插头connector plug 21插座connector socket 22密封/封料seal 23三、运水water line 24喉塞line pug 25喉管tube 26塑胶管plastic tube 27快速接头jiffy quick connector plug 28四、模具零件mold components 29三板模three-plate mold 模具名词中英文对照表 序号中文名英文名 30二板模two-plate mold 31边钉/ 导边leader pin /guide pin

32边司/ 导套bush in g/guide bush ing 33顶针板ejector retainer plate 34托板support plate 35螺丝screw 36管钉dowel pin 37开模槽ply bar score 38内模管位core/cavity inter-lock 39顶针ejector pin 40司筒ejector sleeve 41司筒针ejector pin 42推板stripper plate 43缩呵movable core 44扣机（尼龙拉勾）n yl on latch lock 45斜顶lifter 46模胚（架）mold base 47母模cavity in sert 48公模core insert 49行位（滑块）slide 50 镶件in sert 51压座/斜鸡wedge 52耐磨板/ 油板wedge wear plate 53压条plate 54撑头support pillar 55唧嘴sprue bushing 56挡板stop plate 57定位圈locating ring 58锁扣latch 模具名词中英文对照表 序号中文名英文名 59扣鸡parti ng lock set 60推杆push bar 61栓打螺丝S.H.S.B 62顶板ejector plate 63活动臂lever arm

模具设计与制造外文翻译、中英文翻译、外文文献翻译

Mold design and manufacture The mold is the manufacturing industry important craft foundation, in our country, the mold manufacture belongs to the special purpose equipment manufacturing industry. China although very already starts to make the mold and the use mold, but long-term has not formed the industry. Straight stabs 0 centuries 80's later periods, the Chinese mold industry only then drives into the development speedway. Recent years, not only the state-owned mold enterprise had the very big development, the three investments enterprise, the villages and towns (individual) the mold enterprise's development also quite rapid . Although the Chinese mold industrial development rapid, but compares with the demand, obviously falls short of demand, its main gap concentrates precisely to, large-scale, is complex, the long life mold domain. As a result of in aspect and so on mold precision, life, manufacture cycle and productivity, China and the international average horizontal and the developed country still had a bigger disparity, therefore, needed massively to import the mold every year . The Chinese mold industry except must continue to sharpen the productivity, from now on will have emphatically to the profession internal structure adjustment and the state-of-art enhancement. The structure adjustment aspect, mainly is the enterprise structure to the specialized adjustment, the product structure to center the upscale mold development, to the import and export structure improvement, center the upscale automobile cover mold forming analysis and the structure improvement, the multi-purpose compound mold and the compound processing and the laser technology in the mold design manufacture application, the high-speed cutting, the superfinishing and polished the technology, the information direction develops .

机械专业相关词汇中英文翻译大全

机械专业相关词汇中英文翻译大全 单价unit price 工日合计Man-day total/work-day total 人工费cost of labor 材料费materials expenses 机械的mechanical 检查接线connection test 发电机generator 调相机phase regulator 周波cycle 减负荷装置 load-shedding equipment 断路器柜circuit breaker cabinet 单母线single busbar 互感器transformer 每相电流Current by Phase 封闭式插接close type socket joint 发电机控制面板generator control panel 分级卸载sorted unloading 同步控制synchronization control 调速器 speed governor 信号屏signal screen 继电器relay 高压柜high pressure cabinet 油浸电力变压器oil-immersed power transformer 空气断路器air circuit breaker 控制屏control panel 直流馈电屏direct current feed control panel 电容器electric condenser 计量盘metering panel 成套配电箱whole set of distribution box 落地式floor model 控制开关Control switches 铜芯电力电缆Copper core power cable 控制电缆actuating cable 热缩式电力电缆终端头pyrocondensation power cable terminal 钢结构支架配管steel structure bracket tubing 万用槽钢versatile U-steel 电缆托架 cable bracket 钢制托盘式桥架steel Tray-type cable support system waterproof socket 防水插座 防爆插座Explosion-proof socket 接地绞线earthing twisted pair 接地母线 earthing bus

模具英语翻译大全

1. The undercut area where interfere with slide block need to be filled material to help the slide can move smoothly.（和滑塊干涉的倒勾請加料填平至滑塊可以順利滑動） 2. The thickening added too thick.(加肉太多) 3. The thickening area is too wide.（加肉面積太大） 4. Gate position is moved.(GATE位置移位) 5. The split line of slide block or the area of slide.(滑塊拆的位置) 6. This area is hard to be filled due to the sharp feature(此處有尖角，填充困難) 7. The strength of this area is too weak and isn’t easy to get c old due to the steel too thin. 8. ( 此處鋼材太薄，強度不足而且不容易冷卻) 9. .The semicircle of cylinder avoids designing on slide block lest it will be pulled apart or cause drag mark. 10. ( 圓柱特徵要有一半圓不可以拆在滑塊上，以免粘滑塊造成拉白，拉斷.) 11. The part will be damaged if we make lifter in this area. 12. ( 此處做斜銷在作動時會削到成品肉厚) 13. This is critical surface where is not allow to add material. 14. ( 這個面是裝配面，不能加料) 15. This thick wall area might because sink mark,Please reduce some wall thickness to improve it.) 16. ( 此處料位太厚，會有縮水，建議減料改善) 17. Please confirm whether it is critical surface or not. Please confirm whether it is acceptable to has Slide split line if we have slide in this area. 18. （此面是不是外觀面，此處做滑塊的話會有結合線，是否可以接受） 19. Please confirm whether we can reduce material to the area where have undercut as indicated to have shut off on core and cavity side. No slide block and lifter to be made. 20. （此處有倒勾，能否減料，使公母模靠破，不做滑塊和斜銷） 21. Please confirm the issues of Parting line, Gate position...Etc otherwise the lead-time will be extended. 22. （請盡快確認這種拆模方式和結構，否則會影響模期） 23. The trim mark of the gate is not visual after open the top case if the gate position is design ed like it 24. （GATE做在此處的話.蓋子打開後看不到GATE的修剪部位） 25. We would suggest to enlarging draft to help tool released.) 26. 加大拔模角，以便脫模順利） 27. There are sharp edges if set the parting line at here, It will reduce the tool life 28. （P.L面開在此處，模具上會有尖角和刀口，對模具壽命有影響） 29. If you insist that the gate position have to be as original design then we would